Red Sea ReefWave 25 Manuel utilisateur

User Manual

ENG DE FR

Red Sea ReefWave®

2

Red Sea ReefWave®

3

ENG

User Manual

Silent - Smart - Powerful

Red Sea ReefWave®

4

Contents

Introduction...........................................................................5

Safety ...................................................................................6

ReefBeat app........................................................................7

ReefWave control options...................................................8

Installation.........................................................................10

ReefWave Controller..........................................................12

Using ReefWave without ReefBeat..................................13

ReefWave with ReefBeat - Setting up.............................13

Settings...............................................................................16

Operation with ReefBeat..................................................18

Device Manager.................................................................18

Maintenance......................................................................21

Troubleshooting..................................................................22

Spare Parts list....................................................................24

Warranty..............................................................................26

Red Sea ReefWave®

5

ENG

Introduction

Congratulations on your purchase of Red Sea’s ReefWave®.

Developed specifically for Red Sea, the ReefWave pumps feature the

unique, patented, Maxspect cross-flow technology and provides a Reef-

Spec water motion that’s perfect for corals wherever they are placed in

your aquarium. The combination of an advanced, smooth running and

energy efficient sine-wave motor drive, vibration damping mounts and

dual bearings on all models make ReefWave an especially quiet pulsing

wave pump.

ReefWave is part of Red Sea’s suite of smart devices that can be

operated via Wi-Fi by Red Sea’s ReefBeat® app which needs to be

installed on a smart mobile device with internet connectivity. In addition,

the ReefWave can also be operated directly from its on-board controller.

ReefBeat provides a wide range of easy-to-use functions including

notifications if there is a loss of communication with your ReefWave –

such as in the case of power failure.

ReefBeat® is under constant development and over time will

include additional connected devices as well as additional aquarium

management tools.

Welcome to Red Sea’s smart reef-keeping.

Sincerely,

The Red Sea Team

Specifications ReefWave® 25 ReefWave® 45

Max Flow Rate 7,500 LPH (1980 GPH) 15,000 LPH (3960 GPH)

Power

Consumption 4w - 25w 8w - 45w

Dimension 23cm (9") L x 7cm

(2.8") W x 4cm (1.6") H

31.5cm (12.4") L x 8cm

(3.2") W x 5cm (2") H

Recommended

Aquarium size

45cm – 120cm

(1.5-4 ft)

60cm – 200cm

(2-6 ft)

Maximum glass

thickness 15mm (5

/

8 ") 20mm (3

/

4 ")

Cable Length 3M (10 ft) 3M (10 ft)

Red Sea ReefWave®

6

Safety

PLEASE READ AND FOLLOW ALL SAFETY INSTRUCTIONS

THIS DEVICE IS INTENDED FOR INDOOR USE ONLY.

DANGER: To avoid possible electric shock, special care should be taken

when handling a wet aquarium. For each of the following

situations, do not attempt repairs yourself; return the appliance

to an authorized service facility for service or discard the

appliance.

WARNING: To guard against injury, basic safety precautions should be

observed, including the following:

Do not operate any appliance if it has a damaged cord or plug, if it is

malfunctioning, or if it is dropped or damaged in any manner.

To avoid the possibility of the appliance, plug or receptacle getting wet,

position the aquarium stand and tank to one side of a wall-mounted

receptacle to prevent water from dripping onto the receptacle or plug.

You should create a "drip loop" (see Figure 1) for each cord connecting an

aquarium appliance to a receptacle. The "drip loop" is that part of the cord

below the level of the receptacle, or the connector. Use an extension cord,

if necessary, to prevent water traveling along the cord and coming into

contact with the receptacle. If

the plug or receptacle does get

wet, DO NOT unplug the cord.

Disconnect the fuse or circuit

breaker that supplies power to

the appliance. Then unplug the

device and examine for presence

of water in the receptacle.

Close supervision is necessary when any appliance is used by or near

children.

To avoid injury, do not contact moving parts.

Always unplug an appliance from an outlet when not in use, before

putting on or taking off parts, and before cleaning. Never pull the cord

itself to remove the plug from the outlet. Grasp the plug and pull to

disconnect.

Do not use an appliance for anything other than its intended use.

The use of attachments not recommended or sold by the appliance

manufacturer may cause unsafe conditions.

Do not install or store the appliance where it will be exposed to the

weather or to temperatures below freezing point.

Make sure an appliance mounted on a tank is securely installed before

operating it.

Read and observe all the important notices on the appliance.

Note: A cord rated for less amperes or watts than the appliance rating

may overheat. Care should be taken to arrange the cord so that

it cannot be tripped over or pulled accidentally.

ReefWave pump mounts use STRONG MAGNETIC FIELDS

Strong magnets can cause personal injury.

Keep out or the reach of children.

Persons with medical implants should maintain a

distance of 30cm/12”

Red Sea ReefWave®

7

ENG

Introduction to the ReefBeat app

All of Red Sea’s connected devices can be operated via the ReefBeat

app installed on an Android or iOS smart mobile device (SMD) with an

internet connection. See the full list of supported mobile phones/tablets

on our website.

Through your personal user account on the cloud, ReefBeat enables

you to set up and manage any number of aquariums and add multiple

devices to each of them.

For full functionality, each ReefWave must have a permanent connection

to the internet through your home Wi-Fi network. In this mode of

operation, you will be able to see the current status of your ReefWave

units, change the settings or receive notications on your SMD whenever

you have access to the internet.

The ReefBeat homepage will show you the current status of all of your

connected devices, and links you directly to the Settings Dashboard for

each group or for individual units.

You can install the ReefBeat on multiple SMDs by entering the same user

account details. All SMDs will have the same rights for operating and

changing all of the settings. You should keep this in mind before giving

your user details to any 3rd party.

In the event that you do not have a home network or your home network

does not have an active internet connection, you will only be able to

operate the ReefWave from the controller with limited functionality. More

information about operating the ReefWave in “Controller Mode” is provided

below.

ReefBeat is constantly under development. For the most up to date

operation instructions, view or download the latest user guide from the

Red Sea website at www.redseash.com

If this is your rst Red Sea connected device, it is recommended that

you complete the physical installation of your ReefWave units before

installing the ReefBeat app.

Red Sea ReefWave®

8

Local Controller Functions

Regular Flow

Pump provides a constant flow of water at the intensity you set in

forward or reverse direction.

Uniform Wave

Pump pulses at a uniform rate of 5 seconds between the maximum

intensity in the forward or reverse direction you set and a default

minimum 10% intensity.

Step Wave

Pump pulses at a uniform rate of 5 seconds at a constantly

changing intensity in steps of 10% from the minimum of 20% to

the maximum intensity you set in the forward or reverse direction.

Random Wave

Pump pulses at a randomly varying rate and at a randomly

changing intensity up to the maximum intensity you set in the

forward or reverse direction.

Alternate Wave

Pump will alternate between a uniform wave in the forward

and reverse directions every 5 minutes. User sets the maximum

intensity for both directions.

ReefBeat Mode

In the event that a ReefWave controller has been programmed

by ReefBeat, selecting this mode will implement the last known

24-hour wave schedule even when not connected to the ReefBeat

App.

Feed Mode

Pump will stop for 30 minutes and will automatically resume the

currently selected wave.

Pause/Play

Stop and start the pump on demand as required for pump or tank

maintenance.

Red Sea ReefWave®

9

ENG

ReefBeat Connected Functions

ReefBeat Schedule

User defined 24 hour schedule of up to 10 time slots per day. Each

time slot will implement a user defined wave in the forward, reverse

of alternating direction. There is also a “no wave” option for periods

of no flow.

ReefBeat Wave Library

Multiple customized versions of each of the waves types can be

saved in the wave library for implementation in the daily schedule.

Groups

Up to 3 pumps can be grouped together and run a common schedule.

Regular Flow

Pump provides a constant flow of water at the intensity you set in

forward or reverse direction.

Uniform Wave

Pump pulses at a user definable uniform pulse rate between the

maximum intensity in the forward or reverse direction you set and a

default minimum 10% intensity. Grouped pumps can be run in sync or

anti-sync.

Step Wave

Pump pulses at a user definable uniform pulse rate with intensity

increasing in user definable number of equal steps from the minimum

of 20% to the maximum intensity you set in the forward or reverse

direction.

Random Wave

Pump provides a constant flow of water at the maximum intensity you

set in forward or reverse direction.

Surface Wave

Pump pulses at a user definable uniform pulse rate set in 1/10 of

a second to create a standing wave pattern on the water surface.

Grouped pumps can be run in sync or anti-sync.

Preview

Test wave settings before saving and including in the Schedule.

On/Off

Stop and start a specific pump on demand for individual pump

maintenance.

ReefBeat Feed Mode

All selected ReefBeat connected devices will be stopped for a user

defined period and thereafter will automatically resume the schedule.

ReefBeat Maintenance Mode

All selected ReefBeat connected devices will be stopped until the

Maintenance mode is disabled and wave schedule will be resumed.

ReefBeat Emergency Shut-down

All selected ReefBeat connected devices will be stopped until the

Emergency shut-down is disabled and wave schedule will be resumed.

Notifications

A notification will be sent to your SMD whenever internet connection

to the ReefWave is lost. Could be due to a power or internet outage,

router failure or a fault with a specific device.

Red Sea ReefWave®

10

Installation

WARNING: Running the pumps outside of the water will damage

the bearings and impellor shaft causing noisy operation and a

shortened life for these wear parts!

Pump

The ReefWave pumps can be mounted in the horizontal or vertical

orientation.

Each of the 2 impellor cages can be rotated 360 degrees within the

mounting bracket to adjust the direction of the flow appropriately for

your reefscape. Initially set the A and B markings on the cage to be in

line with the ReefWave logo.

In this position the flow will be approximately perpendicular to the

magnet. The impellors and impellor cages on either side of the pump

motor are slightly different and therefore the rubber parts for each side

are color coded Red and Green to ensure that parts are reassembled

correctly after maintenance.

The impellors of the pumps can rotate both in the forward and reverse

direction however the flow in the forward direction is about 3 times

stronger than the flow in the reverse direction.

When mounting the pumps in the horizontal direction make sure that

the cable is on the top side of the pump. Mount the pumps at least

5cm/2” below the water surface to prevent vortex formation (sucking of

air from the water surface.

Mount the pumps in a location where there is easy access for

adjustment of flow direction and removal for periodic maintenance.

Red Sea ReefWave®

11

ENG

Controller

Locate the ReefWave controller in a convenient position and attach

the mounting bracket using screws or the adhesive tape provided. The

controller is designed to operate in a humid environment but it is not

waterproof. Please take the appropriate precautions in choosing its

location or when removing the controller from the mounting bracket.

Power Supply

Place the power supply in a dry ventilated area. Only use the power

supply provided with the product.

Connect the AC cable to the socket of the power supply and plug it

into the wall outlet or other suitable power center and check that the

indicator LED on the power supply is working. If the indicator LED is not

working, check that the AC cable is properly connected and the wall

outlet is switched on.

Connect the DC jack of the ReefWave to the DC jack of the power supply.

After powering on the unit, the Power indicator LED of the ReefWave will

switch on, the Setting Indicator LED will be off and the Mode indicator

LED will be set to ReefBeat Mode.

NOTE: The pump will not start working until some further action as

described below is taken.

The internal magnets are a north/south pair (look for the N/S markings)

and work together with the external magnet that has a north and south

end. The magnets are very strong and care should be taken to prevent

injury to fingers!

Before installing the pumps for the first time disassemble and

reassemble the pumps as shown in the maintenance section or as

shown on our website to properly familiarize yourself with the parts.

Remember to place the snail guards provided over the impellor cages to

prevent small animals from getting caught inside.

Red Sea ReefWave®

12

Pause/Play & Feed

Local Feed Mode: To activate the local Feed mode press the Pause/

Play button for about 1 second. When active the button will blink on/

off once per second. Wave mode, intensity and direction LEDs will switch

off for the duration of the feed mode. After 30 minutes the Feed mode

will automatically switch off and the chosen wave (and all indicator LEDs)

will resume. To switch off the feed mode manually before the end of the

30-minute period, press the Pause/Play button for about 1 second.

Pause/Play: To stop the pump press the Pause/Play button for about 3

seconds. When active the button will blink on/off every 5 seconds. Wave

mode, intensity and direction LEDs will switch off. To restart the pump,

press the Pause/Play button for about 3 seconds and the chosen wave

(and all indicator LEDs) will resume.

ReefWave Controller

Power Indicator LED

Red light when DC power is available.

Wi-Fi Settings Button and Status LED

If indicator LED is off (ReefWave Wi-Fi is off):

Pressing button for 5 seconds (until double blink) activates Wi-Fi AP mode.

If indicator LED is blinking (ReefWave Wi-Fi is in AP mode):

Pressing button for 5 seconds (until double blink) switches Wi-Fi off.

If indicator LED is on (ReefWave Wi-Fi is connected to a Wi-Fi network):

Pressing button for 5 seconds (until double blink) disconnects the ReefWave

from the network and switches it to Wi-Fi AP mode. (Note: before

disconnecting a ReefWave from a network, delete the specific ReefWave

from ReefBeat via the Device Manager.)

Clear Settings:

Pressing the button for 15 seconds (until double blink) deletes all user

settings and switches off the Wi-Fi. Complete the reset process by

disconnecting and reconnecting the DC power. (Note: before initiating “clear

settings,” delete the specific ReefWave from ReefBeat via Device Manager.)

Wave Mode Button

The Wave Mode settings button toggles the wave program between the 5

built-in Controller Mode waves and the fully programmable ReefBeat mode.

To change the operating mode, activate the mode button by pressing for

1 second, on releasing the button the mode and intensity LEDs will start

blinking and will continue blinking while the mode function is active. A

short press on the mode button will advance the mode by one step to the

right as indicated by the position of the blinking mode indicator LED. Set the

desired wave by pressing and holding the mode button until the LEDs stop

blinking. Note: If the desired wave is not confirmed by holding the button,

after 4 seconds the current position will automatically be selected.

Flow Intensity

dial (10-100%)

Flow direction

indicator LEDs

Pause/Play &

Feed button

Wave mode

selector button

ReefBeat Mode

wave programs

Power & Wi-Fi

Status LEDs 5 on-board

default wave

programs

Wi-Fi Settings

& Reset

Button

Red Sea ReefWave®

13

ENG

Connection and initial setup with ReefBeat

In the event that you do not have an available Wi-Fi network you will not

be able to connect the ReefWave unit to the ReefBeat App however you

can operate it via the local controller as described above. At any time, the

ReefWave can be added to an Online ReefBeat aquarium by completing

the onboarding process described below.

If you are already using ReefBeat for a different device (such as

ReefLED) and have your aquarium set to “Offline” you will need to

reset your aquarium to “Online” before you can connect the ReefWave

and implement customized waves and a 24-hour schedule. Once the

ReefWave has been set up you can take your aquarium Offline again

however the ReefBeat shortcuts and Notifications will be disabled and you

will need to take it back online to implement any changes.

Recommendation: Before connecting your ReefWave to the ReefBeat,

start in Controller mode to check out the effect that the ReefWave has in

various locations in your tank. Rotate the cages to learn how it affects the

flow and check out some of the basic waves and learn the strengths of

the various intensity settings.

Flow Intensity Dial

To change the flow intensity for a Controller Mode wave, press and hold

the center of the dial until the intensity indication LEDs start to blink.

Rotate the dial to the desired direction and intensity as indicated by the

number of blinking LEDs. Press and hold the center of the dial until the

LEDs stop blinking to save the setting. If the desired intensity is not saved

by pressing the center of the dial, after 10 seconds the current intensity

will automatically be selected.

For the Alternating wave, press the center of the dial until the intensity

indication LEDs start to blink. Rotate the dial to the desired forward

intensity, press the center of the dial and rotate to the desired reverse

intensity, press the center of the dial again to return to the forward

direction and save the settings by pressing the center of the dial until the

LEDs stop blinking.

Using ReefWave without ReefBeat - Controller Mode

To operate the ReefWave directly from the ReefWave controller select the

desired wave type using the Wave Mode button and set the intensity and

forward/reverse direction of flow that suits your reefscape. The chosen

wave and intensity will run continuously. You can adjust the flow path

of the pump by rotating the impellor cages. Each cage can be set at a

different angle.

Use the Pause/Play button as described above to stop the pump for

feeding or maintenance.

Red Sea ReefWave®

14

Installing ReefBeat

Download ReefBeat from the app Store or Google Play as appropriate for

your SMD. (In countries without access to Google Play an APK file and

installation instructions can be downloaded from Red Sea’s website.)

After installing ReefBeat, you will be guided through the set-up of your

ReefBeat user account and aquariums, and then you can start adding

your Red Sea connected devices. All of your user account details can be

edited only when your SMD is connected to the internet.

To connect the ReefWave to ReefBeat your aquarium must be set to

“Online”.

Make sure that you select the correct world time zone for where your

aquarium is located. There is also a “Daylight savings Time” (DST) toggle

that needs to be manually switched at the beginning and end of DST for

your location.

If you’ve set up more than one aquarium, select the aquarium from the

dropdown menu at the top of the screen before proceeding.

Adding your first ReefWave to ReefBeat

Make sure that the controller is in ReefBeat mode i.e. the wave mode

indicator LED above the ReefBeat Icon is on.

Set your ReefWave to AP mode by pressing the settings button for 5

seconds (until double blink). The indicator LED should be blinking.

Tap the Add Device button (+) from the Device Manager page, select

the ReefWave 25/45 icon and follow the instructions on the app. If no

ReefWave devices are discovered, check that the ReefWave is in AP

mode and/or refresh the page. If you have installed multiple ReefWave

units and you have already activated the AP mode on all of them, you

will see a list of all of them. Choose any one of them as the first unit and

continue as instructed by the app.

Connecting to the Home Network

ReefBeat will now display a list of Wi-Fi networks and signal strengths

that are available to the ReefWave from its current location. Note: if the

ReefWave is not in its position on the aquarium, your preferred network

may not be accessible when the ReefWave is repositioned.

Select your preferred network and wait a few moments while the

ReefWave connects to it. The indicator LED will now be a solid red.

Follow the instructions on the app for initial settings.

Initial settings

The unique serial number of each ReefWave is the default name for the

device in the app. However, you can set a new name that you prefer

such as “Left”, “Right” etc. These names can be changed at any time

using the “Rename” function from the Device Manager.

For the first ReefWave you connect to your aquarium, you are asked to

select from one of the available wave types which for simplicity will be

scheduled to run constantly for 24-hours per day. Selecting your desired

wave type will open the settings page for this specific wave. By default,

all of the RS waves are set to 40% flow intensity in the forward direction

and 60% reverse. At this stage you can either accept these default

settings or customize them however we recommend that you only

Red Sea ReefWave®

15

ENG

adjust the intensities for now and make other changes later. For a full

explanation of wave setting options see “Current Wave Settings” below.

At any time during the setup you can test the unsaved settings currently

on your screen by tapping on the Play button at the top of the

settings page and see the effect it has on your reefscape. You can also

adjust the flow path of the pump by rotating the impellor cages. Each

cage can be set at a different angle. Stopping the preview will return the

pump to the current active wave according to the schedule.

Once you are satisfied with the settings, save your customized wave

with a unique name. It will be stored in your personal Wave Library

and scheduled for 24 hours a day. ReefBeat will now display the

pump Dashboard providing access to all of the advanced settings such

as creating additional customized waves, setting a multi-wave daily

schedule or the time to switch off the pump when the ReefBeat Feed

Mode is activated. All of these settings can be changed at any time as

described below. To go to the ReefBeat homepage without editing, press

the back arrow.

Adding additional ReefWave units

To connect an additional unit, open the Device Manager page from the

Dashboard 3-dot menu and repeat the process as above.

Up to 3 ReefWave units can “Grouped” together and share a common

Schedule and customized waves however the forward and reverse flow

intensities need to be set for each pump individually. ReefWave 25 and

ReefWave 45 can belong to the same group.

After connecting the additional ReefWave to your home network

(note: all units should be connected to the same network) you should

select if the pump is to be grouped with the first pump or set up as an

ungrouped independent unit.

An ungrouped unit will have the same setup process as for the first unit

and will have a unique schedule, wave types and its own card in the

ReefBeat Homepage.

If you have selected to group the pump, open each of the waves in your

schedule and set the forward and reverse intensities for each pump

individually.

The Preview function will activate all of the pumps in the group to see

the combined effect. If you want to test/set the flows for a specific

pump in the group temporarily switch off the other pumps using the OFF

function in the Device Manager.

ReefBeat Homepage

The ReefBeat homepage will show you the current status of all of your

connected devices. Tapping a device or group card links you directly

to the settings Dashboard for each individual device or group. The

homepage also has “Shortcut” buttons for implementing frequent or

important functions across all of the ReefBeat connected devices. The

Shortcut settings page and Device Manager are accessible from the

3-dot menu of the homepage.

Red Sea ReefWave®

16

Current Wave Settings

Tapping on the current wave card opens the wave settings page with all

of the user definable parameters. For grouped pumps, open the tab for

each pump and set the forward and reverse intensities individually. All

other settings are common for all of the pumps.

At any time, you can test the unsaved settings by tapping on the Play

button at the top of the settings page and see the effect it has on your

reefscape. Grouped pumps will be activated together to see the combined

effect. If you want to test/set the flows for a specific pump in the group

temporarily switch off the other pumps using the OFF function in the

Device Manager.

Once you are satisfied with the settings, save your customized wave with

a unique name. It will be stored in your personal Wave Library and can be

used in your 24-hour schedule.

Custom settings that are available for each wave type

ReefWave Dashboard - Settings

ReefWave is designed to operate automatically according to a 24-hour

schedule that defines up to 10 time-slots allowing different wave types

or intensities during a day.

All of the settings for the ReefWave are viewed/edited from the

Dashboard which shows the current settings for the group or for an

individual ungrouped unit. Tapping on any of the sections on the

dashboard opens the settings page for that feature. Remember to press

Apply or Save to implement any changes you make to the settings.

Tapping on the 3-dot page menu provides quick access to additional

functions such as Wave Library and the Device Manager.

Icon Wave type Forward

Intensity

Reverse

Intensity Pulse time Alternate

Times

Sync / Anti-

sync Steps

Regular Flow √ √ √

Uniform Wave √√√√√

Step Wave √√√√ √

Random Wave √ √ √

Surface Wave √√√

Red Sea ReefWave®

17

ENG

Forward Intensity

Pump flow intensity from 10% to 100% in forward direction.

Reverse Intensity

Pump flow intensity from 10% to 100% in reverse direction.

Pulse time

Pump run time (secs) at maximum and minimum flow for pulsing wave3

types.

Alternate Times

Run time (mins) for automatic cycling between forward and reverse

flows.

Sync / Anti-sync

Synced pumps will pulse together. Anti-sync pumps will pulse alternately.

Steps

Number of steps for incremental intensity increases for Step wave.

Wave Library

Any number of Customized Waves can be created in the Wave Library

and used on all your pumps or aquariums. From the Wave Library,

Customized Waves can be created, edited, deleted, previewed or

selected to be applied directly as the current wave in the 24-hour

schedule. The Wave Library can be accessed from the 3-dot page menu

of the settings page or from the Schedule settings page

Schedule

The Schedule enables you to implement a range of up to 10 different

wave types during the day. The minimum time-slot is 15 minutes. There

is also a “no wave” option which will turn the pump off for the specified

period of time such as to coordinate with automatic feeders that are

not connected to ReefBeat. The schedule implements the Customized

Waves that you have created and saved in the Wave Library in Forward,

Reverse or Alternating setting. When completing the schedule press the

Apply button to save and implement the changes.

Feed Mode

The ReefBeat Feed Mode shortcut provides a quick and simple way to

turn off specific connected devices for a user defined period of time

while feeding the fish or corals.

Feed Mode can be set either from the ReefWave dashboard or from the

ReefBeat Homepage 3-dot> edit shortcut menu.

Open the Feed Mode settings page. Check the pump to be connected

to the shortcut and the amount of time the pump will be switched off

when the ReefBeat “Feed” shortcut button is activated. Press the Apply

button to save and implement the changes.

Red Sea ReefWave®

18

Operation with ReefBeat

The ReefWave will run automatically according to the 24-hour schedule

of customized waves that you have created. Grouped ReefWave units

will all work together with a common schedule but with their individual

flow intensities.

To enjoy all of the functionality that the ReefBeat system has to offer,

the ReefWave units should be connected to the internet at all times.

With an active internet connection, the ReefBeat homepage will show

all of the current settings of the ReefWave group or for each ungrouped

unit individually.

When in ReefBeat mode the Intensity & Direction indicator LEDs on the

controller will display the setting of the current wave according to the

schedule.

Activating any of the ReefBeat shortcuts or activating the On/Off

function from the Device Manager as described below will suspend the

active schedule and put the pump into a “no wave” state and switch

off all of the Intensity & Direction indicator LEDs on the controller.

Deactivating the function will return the pump to the schedule.

Pressing the Mode button on the controller will take the ReefWave

out of the ReefBeat mode and will implement whatever local wave

options will be selected. The ReefBeat homepage will indicate that the

specific unit is now in “Controller Mode”. ReefBeat Shortcuts will not be

implemented on this specific unit however ReefBeat will still receive

notifications as normal.

Pressing the Pause/Play button on the controller will take the ReefWave

out of the ReefBeat mode and will implement either the Feed or Pause

function. The ReefBeat homepage will indicate that the specific unit is

now in “Controller Mode”. ReefBeat Shortcuts will not be implemented on

this specific unit however ReefBeat will still receive notifications as normal.

Device Manager

The Device Manager is accessible from the Page menu in both the

ReefBeat homepage and the ReefWave Dashboard, and contains a

list of all of the Red Sea connected devices that are installed on each

aquarium. The devices are listed according to type and in the order in

which they were added to the aquarium. Tapping the 3-dot menu for

each device type opens a list of advanced functions such as firmware

updates that will be implemented on all devices of this type. Tapping the

3-dot menu for each device opens a list of advanced settings/functions

for each device individually.

Group / Ungroup status

The grouped/ungrouped status of each ReefWave is shown in the Device

Manager.

Up to 3 ReefWave units can be operated together as a group, a 4th

of more ReefWave units can be added to the aquarium however they

can only be operated as ungrouped individual units. The first ReefWave

connected to ReefBeat will automatically be set as grouped, even if it

remains the only member of the group. Subsequent units can be added

to the group and share a common schedule and basic wave settings.

An individual unit can be ungrouped or re-grouped at any time. When a

unit is ungrouped, it will maintain the same settings it had when it was

grouped until changes are made. Once added to a group, the previously

ungrouped unit will automatically get the settings of the group.

To change the status: Device Manager > Device Line menu > Group/

Ungroup

Red Sea ReefWave®

19

ENG

Firmware Updates

From time to time you may receive a notification that a new firmware

version is available for your ReefWave. It is important to keep your

ReefWave firmware updated to ensure compatibility with updates to the

ReefBeat app. If your ReefWave is not permanently connected to the

internet, you will need to connect it temporarily in order to update the

firmware.

Device Manager > Device Type Line and Device Manager > Device Line

– will show the “new firmware available” icon. You can decide to do the

update for all of the devices together or one at a time.

Do not unplug the ReefWave while it is downloading and installing the

new Firmware.

When the firmware update is complete, the “About” page will show

the new version as the current version together with the date and time

that the update was performed. Device Manager > Device Line menu >

About. All of your previous settings will remain as before.

If the firmware update is not successful, the ReefWave will automatically

revert to the previous version. Repeat the process a few minutes later.

If your ReefWave does not seem to be performing correctly after the

update, disconnect and reconnect the power by the DC jack and wait for

the ReefWave to restart.

Removing a ReefWave - Temporary

When switching off or physically removing a ReefWave temporarily such

as when doing reef-scaping or other maintenance on the aquarium or

pump, set the unit to “Out-of-service” through the Device Manager to

prevent ReefBeat from giving you notifications that communication with

the unit has been lost. When returning the unit and/or switching it back

on, remember to return its status to “In-service”. To change the status:

Device Manager >Device Line menu > In-service / Out-of-service.

Removing a ReefWave - Permanent

When permanently removing a ReefWave from an aquarium or before

resetting the unit’s memory, delete the unit from the ReefBeat app:

Device Manager > Device Line menu > Delete.

Deleting before it is switched off will prevent unnecessary notifications

that communication with the unit has been lost.

Clear ReefWave settings

To permanently remove all user settings from the memory of the

ReefWave and return it to its initial default state, perform the following

steps.

Permanently remove (Delete) the specific ReefWave from ReefBeat.

Press the Settings button on the device for about 15 seconds (until

the indicator LED shows a double blink), release the button and wait

for about 10 seconds until a second double blink of the indicator LED

appears. Disconnect and reconnect the power by the DC jack and wait

for the ReefWave to restart. The unit will restart without any user

settings and with the Wi-Fi switched off, exactly as shipped from the

factory. The unit will retain the latest installed version of the firmware.

Red Sea ReefWave®

20

Changing aquarium from Online to Offline

When changing the connectivity state of an Online aquarium with

ReefWave to Offline the Reefwave unit can continue to run the last

implemented 24-hour schedule with all of its customized waves

however the ReefBeat App will not be able to communicate with the

device. Shortcuts and Notifications are disabled and the App will show

all ReefWave units on that aquarium on the homepage as “Controller

Mode” without access to the settings dashboard. All settings however

are stored and returning the aquarium to Online will restore full ReefBeat

functionality with all of the previous settings providing the ReefWave

was not disconnected from the home network.

On/Off

All units of a particular device type or each individual unit can be

switched On/Off as required. This does not disconnect the unit or put it

out of service. It just sets the intensity to zero. For ReefWave it puts the

pumps into a “No-Wave” state.

Device Manager > Device Type Line and Device Manager > Device Line

– On/Off

Notifications

When the ReefWave has a permanent connection to the internet, a

notification will be sent to your SMD whenever connection to the unit is

lost.

A “No communication” message could be due to a power or internet

outage, router failure or a fault with a specific connected device.

If you have more than one Red Sea connected device and connection

to one or more (but not all) devices are lost, you will receive a “Partial

communication” message. You will then be able to see the current

status of all devices from the Device Manager.

In addition to the connectivity ReefBeat will also notify you if you have

activated the Maintenance or Emergency shortcuts and have forgotten to

disable them.

You can set how you wish to receive some of the messages from

“Notifications” in the homepage main menu.

La page charge ...

Red Sea ReefWave 25 Manuel utilisateur

Ce manuel convient également à

Red Sea ReefWave 25 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents