iStorage datashur PRO Manuel utilisateur

Taper
Manuel utilisateur
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
English User Manual - Table of Contents ...............................................4
Deutsch Benutzerhandbuch - Inhaltsverzeichnis ...................................27
Français Manuel d’utilisation - Table des matières ...............................50
#2
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com #2
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
User Manual
Remember to save your PIN in a safe place. If lost or forgotten, there is no way to access the
datAshur PRO.
If you are having difficulty please refer to this complete user manual loaded on your datAshur PRO and is also
available at iStorage’s website: www.istorage-uk.com/support
3.0
Certified to NATO Restricted Level
#3
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
All trademarks and brand names are the
property of their respective owners.
Copyright © 2015 iStorage Limited. All rights reserved.
Windows is a registered trademark of Microsoft Corporation.
All other trademarks and copyrights referred to are the property of their respective owners.
Distribution of the work or derivative work in any standard (paper) book form for commercial purposes is prohibited unless
prior permission is obtained from the copyright holder.
DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD
TO BE LEGALLY INVALID
iStorage shall not be liable by virtue of this warranty, or otherwise, for any incidental, special or consequential damage
including any loss of data resulting from use or operation of the product, whether or not iStorage was apprised of the
possibility of such damages
iStorage datAshur is developed and
manufactured by iStorage Limited and is
based on DataLock® technology licensed
from ClevX, LLC.
iStorage datAshur PRO is developed and
manufactured by iStorage Limited and is
based on DataLock® technology licensed
from ClevX, LLC.
#4
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com
Table of Contents
Introduction .................................................................................................................................. 5
Package contents .......................................................................................................................... 5
1. datAshur PRO Layout ............................................................................................................. 6
2. LED Indicators and their actions.............................................................................................. 6
3. How to use the datAshur PRO for the first time ....................................................................... 7
4. How to change the User PIN .................................................................................................. 7
5. How to enable Options as User ............................................................................................... 8
6. How to enable Read-Only as User .......................................................................................... 9
7. How to enable Read/Write as User .......................................................................................... 9
8. How to set the Timeout Lock in User mode ............................................................................ 10
9. How to disable the Timeout Lock in User mode ..................................................................... 10
10. How to determine the device Version Number in User mode ................................................... 11
11. How to create an Admin PIN .................................................................................................. 11
12. How to unlock the datAshur PRO as Admin ............................................................................ 12
13. How to create a New User PIN in Admin mode ........................................................................ 12
14. How to change the Admin PIN ................................................................................................ 13
15. How to verify whether an Admin/User PIN has been set up ..................................................... 14
16. How to enable Read-Only in Admin mode ............................................................................... 14
17. How to enable Read/Write in Admin mode .............................................................................. 14
18. How to determine the device Version Number in Admin mode ................................................ 15
19. How to set the Timeout Lock in Admin mode .......................................................................... 16
20. How to disable the Timeout Lock in Admin mode ................................................................... 17
21. How to delete all files in Admin mode ..................................................................................... 17
22. Brute Force Hacking Detection ................................................................................................ 18
23. How to Reset the datAshur PRO ............................................................................................. 18
24. Booting from the datAshur PRO ............................................................................................. 19
25. How to configure the datAshur PRO with Windows OS ........................................................... 19
26. How to configure the datAshur PRO with Mac OS ................................................................... 22
27. Technical Support ................................................................................................................... 23
28. Warranty and RMA information ............................................................................................... 23
#5
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
Introduction
Thank you for purchasing the iStorage datAshur® PRO, an ultra secure and easy to use, hardware encrypted USB 3.0 PIN
activated flash drive.
The datAshur PRO has attained FIPS 140-2 Level 3 certification by NIST (certificate no 2688). This is a high level US govern-
ment accreditation and means the product has passed numerous tests relating to the encryption algorithm and tamper-evi-
dence as well as to thwart attacks directed at the Critical Security Parameters.
The datAshur PRO uses military grade AES-XTS 256-bit hardware encryption, which encrypts all data stored on the drive in
real-time. The datAshur PRO requires no software and is OS and host independent.
The datAshur PRO incorporates a rechargeable battery allowing the user to enter a 7-15 digit PIN (Personal Identification
Number) onto the on-board keypad before connecting the drive to a USB port.
Should the drive be lost or stolen, the user can rest assured that all data held on the datAshur PRO is safe and cannot be
accessed by any unauthorised person.
The datAshur PRO can be configured with both a User and Admin PIN, making it perfect for corporate and government
deployment. As the datAshur PRO is unlocked via the onboard keypad and not a host computer, it is not vulnerable to
software/hardware based key-loggers or brute force attacks.
Package contents
• iStorage datAshur PRO
• Extruded Aluminium Sleeve
• QSG - Quick Start Guide
Note: The datAshur PRO rechargeable battery is not fully charged, we recommend the battery be charged
prior to first use. Please plug in the datAshur PRO to a powered USB port for 60 minutes to fully
charge the battery.
Caution: The datAshur PRO is shipped with a default User PIN of 1-1-2-2-3-3-4-4
and although it can be used straight out of the box with the default PIN, for security reasons, we
highly recommend that a new User PIN be created immediately by following instructions under
section 4 “How to change User PIN”.
If you forget your User PIN and no Admin PIN exists, or you forget both PINs, all data will be inaccessible.
#6
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com
1. datAshur PRO Layout
2. LED indicators and their actions
1 2
3
5 6
7
9 0
8
4
RED LED
GREEN LED
KEY Button
Keypad
Keyring, unscrew to add to key ring.
BLUE LED
.
.
.
.
.
.
LED LED State Description LED LED State Description
Red - Fade Out Locking down/incorrect PIN entry /
Red and Green
blinking alternately Factory reset/deleting files in Admin
mode
Red blinking Locked and awaiting factory default
PIN or User defined PIN entry &
Red and Green
flickering together Awaiting Admin PIN entry
Green Solid datAshur PRO is unlocked in User
mode &
Green and Blue
blinking together User Options mode
Green blinking
When connected to a USB port if
Green Led blinks every 2 seconds
this indicates the datAshur PRO has
been set as ‘Read-Only’ &
Green and Blue
flickering together Admin Options mode
Green flickering datAshur PRO is unlocked in
Admin mode &
Red and Blue
blinking together
When not connected to a USB port
indicates that both User and Admin
PINs have been set on the
datAshur PRO
Blue Solid Connected to a USB port &
Red and Blue
flickering together Awaiting Admin PIN change
Blue Blinking
Data exchange with host/changing
User PIN/when not connected to a
USB port indicates an Admin PIN
exists
/ /
Red, Green & Blue
blinking in sequence
to Red and fade out
Drive has developed a fault.
Please retry the command and if the
problem persists contact technical
support
#7
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
PIN requirements:
• Must be between 7-15 digits in length
• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)
• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)
Note: Once the datAshur PRO has been successfully unlocked, the Green LED will remain on and in a solid state
for 30 seconds only, during which time the datAshur PRO needs to be connected to a USB port. It can be locked
down immediately by pressing and holding down the KEY button for 3 seconds, or waiting for the 30
seconds to expire or by clicking the ‘Safely Remove Hardware/Eject’ icon within your operating system.
4. How to change the User PIN
3. How to use the datAshur PRO for the first time
Instructions - first time use LED LED State
1. Press KEY button once
Red, Green & Blue LED’s will flash together once
and then the Red LED will continue to blink
2. Within 10 seconds begin to enter User PIN
(default - 11223344) to unlock datAshur PRO Red LED will continue to blink
3. Press KEY button once Red solid LED changing to Green solid LED
indicating successful default User PIN entry
The datAshur PRO is shipped with a default User PIN of 11223344 and although it can be used straight out of the box with
the default PIN, for security reasons we highly recommend a new User PIN be created immediately by following
the instructions under section 4 ‘How to change the User PIN’.
Please follow the 3 simple steps in the table below to unlock the datAshur PRO with the default User PIN.
Examples of these types of Alphanumerical PINs are:
• For “Password you would press the following keys:
7 (pqrs) 2 (abc) 7 (pqrs) 7 (pqrs) 9 (wxyz) 6 (mno) 7 (pqrs) 3 (def)
• For “iStorage you would press:
4 (ghi) 7 (pqrs) 8 (tuv) 6 (mno) 7 (pqrs) 2 (abc) 4 (ghi) 3 (def)
Using this method, long and easy to remember PIN’s can be created.
Password Tip: You can create a memorable word, name, phrase or any other Alphanumerical PIN combination
by simply pressing the key with the corresponding letters on it.
#8
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com
Instructions LED LED State
1. Press KEY button once
Red, Green & Blue LED’s will flash together once
and then the Red LED will continue to blink
(if Blue LED also blinks this indicates an Admin
PIN has been set up)
2. Within 10 seconds begin to enter the User PIN
(default User PIN 11223344) Red LED will continue to blink
3. Press the KEY button once Red solid LED changing to Green solid LED
indicating successful User PIN entry
4. Press KEY button twice (double-click) Blue LED blinks
5. Within 10 seconds begin to enter New User PIN Blue LED continues to blink
6. Press KEY button twice (double-click) Green LED blinks
7. Within 10 seconds begin to re-enter New User PIN Green LED continues to blink
8. Press KEY button twice (double-click) Red solid LED changing to Green solid LED
indicating User PIN change successful
Note: If a mistake was made while defining a new PIN or the procedure was not completed, the drive will retain
the old PIN.
5. How to enable Options as User
Instructions LED LED State
1. Press KEY button once
Red, Green & Blue LED’s will flash together once
and then the Red LED will continue to blink
(if Blue LED also blinks this indicates an Admin
PIN has been set up)
2. Within 10 seconds begin to enter your User PIN Red LED will continue to blink
3. Press the KEY button once Red solid LED changing to Green solid LED
indicating successful User PIN entry
4. Press the KEY button 3 times - treble
click & Green and Blue LED’s blinking together
awaiting new instructions in OPTIONS mode.
The Options mode will allow the User to perform different functions such as enabling and disabling the datAshur PRO as
‘Read-Only’, setting a ‘Timeout’ automatic lock and determining the version of the device.
The table below illustrates how to access the Options mode, sections 6 - 10 describe how to perform the various functions.
#9
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
6. How to enable Read-Only as User
7. How to enable Read/ Write as User
Instructions LED LED State
1. Unlock the datAshur PRO with User PIN Red solid LED changing to Green solid LED
indicating successful User PIN entry
2. Enable Options by pressing the KEY button 3 times -
treble click & Green and Blue LED’s blinking together
awaiting new instructions in OPTIONS mode.
3. Within 10 seconds begin to Press button number 7
(pqRs) followed by the number 6 (mnO) button - (76) & Green and Blue LED’s continue to blink together
4. Press KEY button once
Red solid LED changing to Green solid LED.
When datAshur PRO is inserted into a USB port
the Green LED blinks every two seconds indicat-
ing the drive is in Read-Only mode
The User is able to write content to the datAshur PRO and restrict access to read-only.
This is done by performing the following steps.
Once activated, access is limited to Read-Only until write protect is disabled.
Note: We have applied a naming convention to make it easy for the User to remember the keystrokes for each
optional setting. In the table above we have used numbers that represent the ‘first letters’ of the optional feature
name. For example, Read-Only = 7 (pqRs) 6 (mnO).
Admin can override User Read/Write settings by enabling/disabling Read/Write in Admin mode.
Instructions LED LED State
1. Unlock the datAshur PRO with User PIN Red solid LED changing to Green solid LED
indicating successful User PIN entry
2. Press the KEY button three times (treble-click)
& Green and Blue LED’s blinking together
3. Within 10 seconds begin to Press the number 7 (pqRs)
button followed by the number 9 (Wxyz) button (79) & Green and Blue LED’s continue to blink together
4. Press KEY button once
Red solid LED changing to Green solid LED.
When the datAshur PRO is inserted into a USB
port a solid Green LED indicates the datAshur
PRO is Read/Write enabled
Restricted write protect (Read-Only) access can be turned off with access restored to Read/Write.
This is done by performing the following Steps.
Once activated, access is restored to the default Read/Write state.
Note: Admin can override User Read/Write settings by enabling/disabling Read/Write in Admin mode.
#10
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com
8. How to set the Timeout Lock in User mode
To protect against unauthorised access when the datAshur PRO is connected to a host and unattended, the datAshur PRO can
be set to automatically lock after a pre-set amount of time.
In its default state, the datAshur PRO Timeout Lock feature is turned off. The Timeout Lock feature can be set to activate (lock)
anywhere between 1 and 99 minutes.
To set the Timeout Lock, please follow steps in the table below.
Instructions LED LED State
1. Unlock the datAshur PRO with User PIN Red solid LED changing to Green solid LED
indicating successful User PIN entry
2. Enable Options by pressing the KEY button 3 times -
treble click & Green and Blue LED’s blinking together
awaiting new instructions in OPTIONS mode.
3. Within 10 seconds begin to Press button number 8
(Tuv) followed by the number 5 (jkL) button - (85) & Green and Blue LED’s continue to blink together
4. Press KEY button once Blinking Green LED
5. Within 10 seconds begin enter the length of User
Timeout in 2 digits:
00 = 0 minutes (default)
01 = 1 minute
99 = 99 minutes etc
Green LED continues to blink
6. Press the Key button once Red solid LED changing to Green solid LED -
Admin can override USER Timeout Lock
9. How to disable the Timeout Lock in User Mode
Instructions LED LED State
1. Unlock the datAshur PRO with User PIN Red solid LED changing to Green solid LED
indicating successful User PIN entry
2. Enable Options by pressing the KEY button 3 times -
treble click & Green and Blue LED’s blinking together
awaiting new instructions in OPTIONS mode.
3. Within 10 seconds begin to Press button number 8
(Tuv) followed by the number 5 (jkL) button - (85) & Green and Blue LED’s continue to blink together
4. Press KEY button once Blinking Green LED
5. Within 10 seconds begin to press the number 0 button
twice (double click) (zero,zero)-(00) Green LED continues to blink
6. Press the Key button once Red solid LED changing to Green solid LED -
Timeout Lock has been disabled
To disable the Timeout Lock, please follow steps in the table below.
#11
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
11. How to create an Admin PIN
An Admin PIN is a useful feature for corporate deployment, for example:
• Recovering data from a drive and configuring a new User PIN in the event an employee has forgotten their PIN
• Retrieving data from a drive if an employee leaves the company
• Setting policies such as ‘Read-Only’
• The Admin PIN can be used to override all User settings
PIN requirements:
• Must be between 7-15 digits in length
• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)
• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)
Instructions LED LED State
1. Unlock the datAshur PRO with User PIN Red solid LED changing to Green solid LED
indicating successful User PIN entry
2. Enable Options by pressing the KEY button 3 times -
treble click & Green and Blue LED’s blinking together
awaiting new instructions in OPTIONS mode.
3. Within 10 seconds begin to Press button number 8
(tuV) followed by the number 6 (mNo) button - (86) & Green and Blue LED’s continue to blink together
4. Press KEY button once
Red, Green & Blue LED’s will quickly blink
together once followed by the Red LED blinking
to the most significant digit of revision and
the Green LED will blink according to the least
significant digit of the revision number
For example, if the revision number is ‘1.11’, the Red LED will blink once (1) and the Green LED will blink eleven (11)
times. Once the sequence has ended the Red, Green & Blue LED’s will blink together once and then to solid Green.
10. How to determine the device Version Number in User mode
To display the device Version Number of the datAshur PRO do the following.
#12
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com
Instructions LED LED State
1. Press KEY button once
Red, Green & Blue LED’s will flash together once
and then the Red LED will continue to blink
(if Blue LED also blinks this indicates an Admin
PIN has been set up)
2. Within 10 seconds begin to enter your User PIN (default
PIN 11223344) Red LED will continue to blink
3. Press the KEY button once Red solid LED changing to Green solid LED
indicating successful User PIN entry
4. Press and hold down the number 1 button and press
the KEY button twice (double click) (1 & ) &
Red and Blue LED’s flicker together ready to
receive new Admin PIN
5. Within 10 seconds begin to enter your new Admin PIN & Red and Blue LED’s continue to flicker together
6. Press KEY button twice (double click) Green LED blinks
7. Within 10 seconds begin to re-enter your new Admin PIN Green LED continues to blink
8. Press KEY button twice (double click) Red solid LED changing to Green solid LED
indicating successful Admin PIN entry
12. How to unlock the datAshur PRO as Admin
Instructions LED LED State
1. Press and hold down the number 1 button and press the
KEY button once (1 & ) & Red and Green LED’s flicker together
2. Within 10 seconds begin to enter your Admin PIN & Red and Green LED’s continue to flicker together
3. Press the KEY button once Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we
highly recommend that a new User PIN be created immediately once the drive has been unlocked
using the Admin PIN. Refer to section 13 on page 12.
Note: Once the datAshur PRO has been successfully unlocked, the Green LED will remain on for 30 seconds only,
during which time the datAshur PRO needs to be connected to a USB port. It can be locked down immediately by
pressing and holding down the KEY button for 3 seconds, or waiting for the 30 seconds to expire or by
clicking the ‘Safely Remove Hardware/Eject’ icon within your operating system.
13. How to create a New User PIN in Admin mode
Creating a new User PIN in Admin mode will become necessary if the datAshur PRO has been unlocked for any reason with
the Admin PIN, as this will automatically clear the User PIN. To create a new User PIN in Admin mode please follow the
instructions on the table below.
#13
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
Instructions LED LED State
1. Unlock the datAshur PRO with Admin PIN Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
2. Press the KEY button twice (double-click) Blue LED blinking ready to receive new PIN
3. Within 10 seconds begin to enter your New User PIN Blue LED continues to blink
4. Press KEY button twice (double-click) Green LED blinks
5. Within 10 seconds begin to re-enter the New User PIN Green LED continues to blink
6. Press KEY button twice (double-click) Off Red LED quickly fades out to indicate
successful creation of a New User PIN
Admin PIN requirements:
• Must be between 7-15 digits in length
• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)
• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)
14. How to change the Admin PIN
Once an Admin PIN has been created, the datAshur PRO needs to be unlocked in Admin mode in order to change the Admin
PIN. The Admin PIN cannot be changed from the User mode.
Instructions LED LED State
1. Unlock the datAshur PRO with existing Admin PIN Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
2. Press and hold down the number 1 button and press the
KEY button twice (double-click) (1 & ) & Red and Blue LED’s flicker together ready to
receive new Admin PIN
3. Within 10 seconds begin to enter your New Admin PIN & Red and Blue LED’s continue to flicker together
4. Press KEY button twice (double-click) Green LED blinks
5. Within 10 seconds begin to re-enter the New Admin PIN Green LED continues to blink
6. Press KEY button twice (double-click) Red solid LED changing to a flickering Green
LED indicating successful Admin PIN change
Admin PIN requirements:
• Must be between 7-15 digits in length
• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)
• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)
Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we
highly recommend that a new User PIN be created immediately once the drive has been unlocked
using the Admin PIN. Refer to section 13 on page 12.
Note: If a mistake was made while defining a new Admin PIN or the procedure was not completed, the drive
will retain the old Admin PIN.
#14
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com #14
www.istorage-uk.com
16. How to enable Read-Only in Admin mode
Instructions LED LED State
1. Unlock the datAshur PRO with Admin PIN Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
2. Press the KEY button three times
(treble-click) & Green and Blue LED’s flicker together
3. Within 10 seconds begin to press the number 7 (pqRs)
button followed by the number 6 (mnO) button (76) & Green and Blue LED’s continue to flicker
together
4. Press KEY button once
Red solid LED changing to flickering Green
LED. when the datAshur PRO is inserted into
a USB port the Green LED blinks every two
seconds indicating the datAshur PRO is in
Read-Only mode
17. How to enable Read/Write in Admin mode
When Admin writes content to the datAshur PRO and restricts access to read-only, the User cannot change this setting in
User mode. To set the datAshur PRO to Read-Only, please follow the steps below.
Admin can override User set Read-Only by enabling Read/Write on the datAshur PRO using the Admin PIN. To set the
datAshur PRO to Read/Write, please follow the steps below.
15. How to verify whether an Admin/User PIN has been set up
1. Press KEY button once Red, Green & Blue LED’s will flash together once, then one of the following states occurs.
Only User/default PIN exists Red LED blinks
Only Admin PIN exists Blue LED blinks
Both User and Admin PIN’s exist & Red and Blue LED’s blink together
The following table illustrates how to determine which PINs, User and/or Admin, have been set up.
With the datAshur PRO in a locked state (all LEDs off), press the KEY button once.
Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we
highly recommend that a new User PIN be created immediately once the drive has been unlocked
using the Admin PIN. Refer to section 13 on page 12.
Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we
highly recommend that a new User PIN be created immediately once the drive has been unlocked
using the Admin PIN. Refer to section 13 on page 12.
#15
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
#15 www.istorage-uk.com
18. How to determine the device Version Number in Admin mode
Instructions LED LED State
1. Unlock the datAshur PRO with Admin PIN Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
2. Press the KEY button three times
(treble-click) & Green and Blue LED’s flicker together
3. Within 10 seconds begin to press the number 8 (tuV)
button followed by the number 6 (mNo) button (86) & Green and Blue LED’s continue to flicker
together
4. Press KEY button once
Red, Green & Blue LED’s will quickly blink
together once followed by the Red LED blinking
to the most significant digit of revision and
the Green LED will blink according to the least
significant digit of the revision number
For example, if the revision number is ‘1.11’, the Red LED will blink once (1) and the Green LED will blink eleven (11)
times. Once the sequence has ended the Red, Green & Blue LED’s will blink together once and then to flickering Green LED.
Instructions LED LED State
1. Unlock the datAshur PRO with Admin PIN Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
2. Press the KEY button three times
(treble-click) & Green and Blue LED’s flicker together
3. Within 10 seconds begin to press the number 7 (pqRs)
button followed by the number 9 (Wxyz) button (79) & Green and Blue LED’s continue to flicker
together
4. Press KEY button once
Red solid LED changing to flickering Green
LED. when the datAshur PRO is inserted into a
USB port the Green LED is solid indicating the
datAshur PRO is Read/Write enabled
To display the device Version Number of the datAshur PRO do the following.
Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we
highly recommend that a new User PIN be created immediately once the drive has been unlocked
using the Admin PIN. Refer to section 13 on page 12.
#16
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com #16
www.istorage-uk.com
19. How to set the Timeout Lock in Admin mode
Instructions LED LED State
1. Unlock the datAshur PRO with Admin PIN Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
2. Press the KEY button 3 times
(treble click) & Green and Blue LED’s flicker together
awaiting new instructions in OPTIONS mode.
3. Within 10 seconds begin to press button number 8
(Tuv) followed by the number 5 (jkL) button - (85) & Green and Blue LED’s continue to flicker
together
4. Press KEY button once Blinking Green LED
5. Within 10 seconds begin to enter the length of User
Timeout in 2 digits:
00 = 0 minutes (default)
01 = 1 minute
99 = 99 minutes etc
Green LED continues to blink
6. Press the Key button once Red solid LED changing to flickering Green
LED. Admin can override USER Lock Timeout
To protect against unauthorised access when the datAshur PRO is connected to a host and unattended, the datAshur PRO can
be set to automatically lock after a pre-set amount of time.
In its default state, the datAshur PRO Timeout Lock feature is turned off. The Timeout Lock feature can be set to
activate (lock) anywhere between 1 and 99 minutes. Admin Timeout Lock settings will override User settings.
To set the Timeout Lock please follow steps in the table below.
Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we
highly recommend that a new User PIN be created immediately once the drive has been unlocked
using the Admin PIN. Refer to section 13 on page 12.
#17
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
#17 www.istorage-uk.com
Instructions LED LED State
1. Unlock the datAshur PRO with Admin PIN Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
2. Press the KEY button 3 times (treble-click)
& Green and Blue LED’s flicker together
3. Within 10 seconds begin to press the number 3 (Def)
button followed by the number 2 (Abc) button (32) & Green and Blue LED’s continue to flicker
together
4. Press KEY button once / Red and Green LED’s blink alternately
5. Within 10 seconds begin to enter your Admin PIN again / Red and Green LED’s continue to blink
alternately
6. Press KEY button once
Red solid LED to Red & Green solid LED’s to a
Green flickering LED indicating that all data has
been deleted
21. How to delete all files in Admin mode
In the event that Admin wants to delete all data stored on the datAshur PRO, please follow the instructions below. All Admin
settings will remain on the datAshur PRO but all data will be deleted and cannot be retrieved and the datAshur PRO will have
to be reformatted (see section 25 or 26)
Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we
highly recommend that a new User PIN be created immediately once the drive has been unlocked
using the Admin PIN. Refer to section 13 on page 12.
Instructions LED LED State
1. Unlock the datAshur PRO with Admin PIN Red solid LED followed by a flickering Green
LED indicating successful Admin PIN entry
2. Enable Options by pressing the KEY button 3 times -
treble click & Green and Blue LED’s flickering together
awaiting new instructions in OPTIONS mode.
3. Within 10 seconds begin to Press button number 8
(Tuv) followed by the number 5 (jkL) button - (85) & Green and Blue LED’s continue to flicker
together
4. Press KEY button once Blinking Green LED
5. Within 10 seconds begin to press the number 0 button
twice (zero,zero) - (00) Green LED continues to blink
6. Press the Key button once Red solid LED changing to flickering Green
LED. Timeout Lock has been disabled
20. How to disable the Timeout Lock in Admin Mode
To disable the Timeout Lock, please follow steps in the table below.
#18
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com
23. How to Reset the datAshur PRO
In the event both the Admin and User PINs have been forgotten, or the user wants to delete all data stored on the datAshur
PRO, please follow the instructions below.
The reset process will clear all cryptographic parameters including both User and Admin PINs. This means the datAshur PRO
will revert back to the default User PIN set as11223344 - see section 4 on page 7 on how to change the User PIN. Also, since
this will force the creation of a new encryption key, the datAshur PRO will have to be reformatted (see section 25 or 26).
Caution: Resetting the datAshur PRO will delete all data stored on the drive.
PINs Set-up on
datAshur PRO
PIN used to unlock
datAshur PRO What happens after 10 consecutive incorrect PIN entries?
Admin & User
PINs User PIN
The datAshur PRO’s brute force mechanism will trigger and the User PIN will
be deleted.
All data will remain on the datAshur PRO and can only be accessed by the
Admin entering the correct Admin PIN.
Admin & User
PINs Admin PIN The datAshur PRO’s brute force mechanism will trigger and both the User and
Admin PINs, the encryption key and all data will be deleted and lost forever.
User PIN Only User PIN The datAshur PRO’s brute force mechanism will trigger and the User PIN,
the encryption key along with all data will be deleted and lost forever.
Admin PIN Only Admin PIN The datAshur PRO’s brute force mechanism will trigger and the Admin PIN,
the encryption key along with all data will be deleted and lost forever.
If both Admin and User PINs have been created and a User enters an incorrect User PIN 10 (ten) consecutive times, the
datAshur PRO’s brute force mechanism will trigger and the User PIN will be deleted. All data will remain on the datAshur PRO
and can only be accessed by the Admin entering the correct Admin PIN.
If Admin enters an incorrect Admin PIN 10 (ten) consecutive times, then both the User and Admin PINs, the encryption key
and all data will be deleted and lost forever. The datAshur PRO will then revert back to factory default settings and will need to
be formatted before it can be reused.
The table below illustrates the different PIN set-up states and what happens when entering an incorrect Admin or User PIN
incorrectly 10 (ten) consecutive times.
The datAshur PRO, unlike other similar drives, incorporates a random number generator, once the drive is reset a new
encryption key is randomly generated.
22. Brute Force Hacking Detection
#19
www.istorage-uk.com
iStorage datAshur® Pro Manual – v 2.9
25. How to configure the datAshur PRO with Windows OS
In the event that hacking detection has been triggered by entering the incorrect PIN 10 times in succession or the drive
has been reset, all data on the drive will be lost forever. Once a New User PIN has been created, the datAshur PRO
will need to be initialised and formatted.
To initialise your datAshur PRO, do the following:
1. Create a New User PIN (see section 4).
2. Unlock the datAshur PRO by entering the New User PIN and connect to a computer’s USB port.
Instructions LED LED State
1. Press and hold down number 7 (seven) button and then
press the KEY button and release buttons
(7 & )
/ Red and Green LED’s blink alternately
2. Within 10 seconds begin to Press the number 9 button
three times (triple click) (999) / Red and Green LED’s continue to blink
alternately
3. Press and hold down number 7 (seven) button and then
press the KEY button and release buttons
(7 & )
Solid Red and Green LED’s change to a solid
Red LED that fades out to complete the reset
process
4. Proceed by clicking on Format disk.
Select FAT32 or NTFS depending on your needs, enter a Volume Label and click Start.
3. The computer should notify the user with the following message:
24. Booting from the datAshur PRO
iStorage datAshur PRO USB drives are equipped with a boot delay feature in order to accommodate power cycling
during a host boot process.
There may be occasions where you might want to boot from the datAshur PRO for various reasons. When booting from the
datAshur PRO, you are running your computer with the operating system that’s installed on the datAshur PRO.
No special actions are required on the part of the user, and to use this feature, simply unlock the drive and connect to the USB
port of a host computer.
To force an immediate lock, always unplug to remove USB power to the datAshur PRO.
OFF
#20
iStorage datAshur® Pro Manual – v 2.9
www.istorage-uk.com
5. Click OK to continue with formatting the drive.
6. The procedure will finish formatting the drive and confirm that formatting has been completed.
While the datAshur PRO is formatting the BLUE LED will be flashing.
Once finished, the BLUE LED becomes solid and your datAshur PRO is ready for use.
Warning: This procedure will erase ALL data on the drive.
In case that the formatting wizard does not appear, please follow the procedure below:
1. Windows 7: Right click Computer and then click Manage and then select Disk Management
Windows 8: Right click left corner of desktop and select Disk Management
Windows 10: Right click on the start button and select Disk Management
2. In the Computer Management window under the Disk Management tab, the datAshur PRO is
recognised as a removable device in raw format.
3. In the blank area under the unallocated section right click Removable Raw Drive and select Format.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

iStorage datashur PRO Manuel utilisateur

Taper
Manuel utilisateur