iStorage Datashur Personal2 Manuel utilisateur

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

English User Manual - Table of Contents ...............................................4

Deutsch Benutzerhandbuch - Inhaltsverzeichnis ...................................27

Français Manuel d’utilisation - Table des matières ...............................50

Svenska Användarhandbok - Innehållsförteckning ................................71

#2

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com #2

www.istorage-uk.com

User Manual

Remember to save your PIN in a safe place. If lost or forgotten, there is no way to access the

datAshur Personal2.

If you are having difﬁculty please refer to this complete user manual loaded on your datAshur Personal2 and is also

available at iStorage’s website: www.istorage-uk.com/support

3.0

#3

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

User Manual

All trademarks and brand names are the

property of their respective owners.

Windows is a registered trademark of Microsoft Corporation.

All other trademarks and copyrights referred to are the property of their respective owners.

Distribution of the work or derivative work in any standard (paper) book form for commercial purposes is prohibited unless

prior permission is obtained from the copyright holder.

DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND

WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD

TO BE LEGALLY INVALID

iStorage shall not be liable by virtue of this warranty, or otherwise, for any incidental, special or consequential damage

including any loss of data resulting from use or operation of the product, whether or not iStorage was apprised of the

possibility of such damages

iStorage datAshur is developed and

manufactured by iStorage Limited and is

based on DataLock® technology licensed

from ClevX, LLC.

iStorage datAshur Personal2 is developed and

manufactured by iStorage Limited and is

based on DataLock® technology licensed

from ClevX, LLC.

#4

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com

Table of Contents

Introduction .................................................................................................................................. 5

Package contents .......................................................................................................................... 5

1. datAshur Personal2 Layout ..................................................................................................... 6

2. LED Indicators and their actions.............................................................................................. 6

3. How to use the datAshur Personal2 for the ﬁrst time ................................................................ 7

4. How to change the User PIN .................................................................................................. 7

5. How to enable Options as User ............................................................................................... 8

6. How to enable Read-Only as User .......................................................................................... 9

7. How to enable Read/Write as User .......................................................................................... 9

8. How to set the Timeout Lock in User mode ............................................................................ 10

9. How to disable the Timeout Lock in User mode ..................................................................... 10

10. How to determine the device Version Number in User mode ................................................... 11

11. How to create an Admin PIN .................................................................................................. 11

12. How to unlock the datAshur Personal2 as Admin ..................................................................... 12

13. How to create a New User PIN in Admin mode ........................................................................ 12

14. How to change the Admin PIN ................................................................................................ 13

15. How to verify whether an Admin/User PIN has been set up ..................................................... 14

16. How to enable Read-Only in Admin mode ............................................................................... 14

17. How to enable Read/Write in Admin mode .............................................................................. 14

18. How to determine the device Version Number in Admin mode ................................................ 15

19. How to set the Timeout Lock in Admin mode .......................................................................... 16

20. How to disable the Timeout Lock in Admin mode ................................................................... 17

21. How to delete all ﬁles in Admin mode ..................................................................................... 17

22. Brute Force Hacking Detection ................................................................................................ 18

23. How to Reset the datAshur Personal2 ..................................................................................... 18

24. Booting from the datAshur Personal2 ..................................................................................... 19

25. How to conﬁgure the datAshur Personal2 with Windows OS ................................................... 19

26. How to conﬁgure the datAshur Personal2 with Mac OS ........................................................... 22

27. Technical Support ................................................................................................................... 23

28. Warranty and RMA information ............................................................................................... 23

#5

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

Introduction

Thank you for purchasing the iStorage datAshur® Personal2, an ultra secure and easy to use, hardware encrypted USB 3.0 PIN

activated ﬂash drive.

The datAshur Personal2 uses military grade AES-XTS 256-bit hardware encryption, which encrypts all data stored on the

drive in real-time. The datAshur Personal2 requires no software and is OS and host independent.

The datAshur Personal2 incorporates a rechargeable battery allowing the user to enter a 7-15 digit PIN (Personal Identiﬁcation

Number) onto the on-board keypad before connecting the drive to a USB port.

Should the drive be lost or stolen, the user can rest assured that all data held on the datAshur Personal2 is safe and cannot be

accessed by any unauthorised person.

The datAshur Personal2 can be conﬁgured with both a User and Admin PIN, making it perfect for corporate and government

deployment. As the datAshur Personal2 is unlocked via the onboard keypad and not a host computer, it is not vulnerable to

software/hardware based key-loggers or brute force attacks.

Package contents

Note: The datAshur Personal2 rechargeable battery is not fully charged, we recommend the battery be

charged prior to ﬁrst use. Please plug in the datAshur Personal2 to a powered USB port for 60 minutes

to fully charge the battery.

Caution: The datAshur Personal2 is shipped with a default User PIN of 1-1-2-2-3-3-4-4

and although it can be used straight out of the box with the default PIN, for security reasons, we

highly recommend that a new User PIN be created immediately by following instructions under

section 4 “How to change User PIN”.

If you forget your User PIN and no Admin PIN exists, or you forget both PINs, all data will be inaccessible.

• iStorage datAshur Personal2

• QSG - Quick Start Guide

#6

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com

1. datAshur Personal2 Layout

2. LED indicators and their actions

LED LED State Description LED LED State Description

Red - Fade Out Locking down/incorrect PIN entry /

Red and Green

blinking alternately Factory reset/deleting ﬁles in Admin

mode

Red blinking Locked and awaiting factory default

PIN or User deﬁned PIN entry &

Red and Green

ﬂickering together Awaiting Admin PIN entry

Green Solid datAshur Personal2 is unlocked in

User mode &

Green and Blue

blinking together User Options mode

Green blinking When connected to a USB port if

Green Led blinks every 2 seconds

this indicates the datAshur Person-

al2 has been set as ‘Read-Only’ &

Green and Blue

ﬂickering together Admin Options mode

Green ﬂickering datAshur Personal2 is unlocked in

Admin mode &

Red and Blue

blinking together When not connected to a USB port

indicates that both User and Admin

PINs have been set on the

datAshur Personal2

Blue Solid Connected to a USB port &

Red and Blue

ﬂickering together Awaiting Admin PIN change

Blue Blinking Data exchange with host/changing

User PIN/when not connected to a

USB port indicates an Admin PIN

exists

/ /

Red, Green & Blue

blinking in sequence

to Red and fade out

Drive has developed a fault.

Please retry the command and if the

problem persists contact technical

support

LOCK LED, stand by while the drive is locked

UNLOCK LED, drive is unlocked when ashing

Keypad

Key Button, used to activate the drive and to enter PIN codes

BLUE LED, when solid, the drive is connected to the computer, when

ashing data is being transferred.

#7

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

PIN requirements:

• Must be between 7-15 digits in length

• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)

• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)

Note: Once the datAshur Personal2 has been successfully unlocked, the Green LED will remain on and in a solid

state for 30 seconds only, during which time the datAshur Personal2 needs to be connected to a USB port. It can be

locked down immediately by pressing and holding down the KEY button for 3 seconds, or waiting for the 30

seconds to expire or by clicking the ‘Safely Remove Hardware/Eject’ icon within your operating system.

4. How to change the User PIN

3. How to use the datAshur Personal2 for the ﬁrst time

Instructions - ﬁrst time use LED LED State

1. Press KEY button once

Red, Green & Blue LED’s will ﬂash together once

and then the Red LED will continue to blink

2. Within 10 seconds begin to enter User PIN

(default - 11223344) to unlock datAshur Personal2Red LED will continue to blink

3. Press KEY button once Red solid LED changing to Green solid LED

indicating successful default User PIN entry

The datAshur Personal2 is shipped with a default User PIN of 11223344 and although it can be used straight out of the box

with the default PIN, for security reasons we highly recommend a new User PIN be created immediately by

following the instructions under section 4 ‘How to change the User PIN’.

Please follow the 3 simple steps in the table below to unlock the datAshur Personal2 with the default User PIN.

Examples of these types of Alphanumerical PINs are:

• For “Password” you would press the following keys:

7 (pqrs) 2 (abc) 7 (pqrs) 7 (pqrs) 9 (wxyz) 6 (mno) 7 (pqrs) 3 (def)

• For “iStorage” you would press:

4 (ghi) 7 (pqrs) 8 (tuv) 6 (mno) 7 (pqrs) 2 (abc) 4 (ghi) 3 (def)

Using this method, long and easy to remember PIN’s can be created.

Password Tip: You can create a memorable word, name, phrase or any other Alphanumerical PIN combination

by simply pressing the key with the corresponding letters on it.

#8

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com

Instructions LED LED State

1. Press KEY button once

Red, Green & Blue LED’s will ﬂash together once

and then the Red LED will continue to blink

(if Blue LED also blinks this indicates an Admin

PIN has been set up)

2. Within 10 seconds begin to enter the User PIN

(default User PIN 11223344) Red LED will continue to blink

3. Press the KEY button once Red solid LED changing to Green solid LED

indicating successful User PIN entry

4. Press KEY button twice (double-click) Blue LED blinks

5. Within 10 seconds begin to enter New User PIN Blue LED continues to blink

6. Press KEY button twice (double-click) Green LED blinks

7. Within 10 seconds begin to re-enter New User PIN Green LED continues to blink

8. Press KEY button twice (double-click) Red solid LED changing to Green solid LED

indicating User PIN change successful

Note: If a mistake was made while deﬁning a new PIN or the procedure was not completed, the drive will retain

the old PIN.

5. How to enable Options as User

Instructions LED LED State

1. Press KEY button once

Red, Green & Blue LED’s will ﬂash together once

and then the Red LED will continue to blink

(if Blue LED also blinks this indicates an Admin

PIN has been set up)

2. Within 10 seconds begin to enter your User PIN Red LED will continue to blink

3. Press the KEY button once Red solid LED changing to Green solid LED

indicating successful User PIN entry

4. Press the KEY button 3 times - treble

click & Green and Blue LED’s blinking together

awaiting new instructions in OPTIONS mode.

The Options mode will allow the User to perform different functions such as enabling and disabling the datAshur Personal2 as

‘Read-Only’, setting a ‘Timeout’ automatic lock and determining the version of the device.

The table below illustrates how to access the Options mode, sections 6 - 10 describe how to perform the various functions.

#9

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

6. How to enable Read-Only as User

7. How to enable Read/ Write as User

Instructions LED LED State

1. Unlock the datAshur Personal2 with User PIN Red solid LED changing to Green solid LED

indicating successful User PIN entry

2. Enable Options by pressing the KEY button 3 times -

treble click & Green and Blue LED’s blinking together

awaiting new instructions in OPTIONS mode.

3. Within 10 seconds begin to Press button number 7

(pqRs) followed by the number 6 (mnO) button - (76) & Green and Blue LED’s continue to blink together

4. Press KEY button once

Red solid LED changing to Green solid LED.

When datAshur Personal2 is inserted into a USB

port the Green LED blinks every two seconds

indicating the drive is in Read-Only mode

The User is able to write content to the datAshur Personal2 and restrict access to read-only.

This is done by performing the following steps.

Once activated, access is limited to Read-Only until write protect is disabled.

Note: We have applied a naming convention to make it easy for the User to remember the keystrokes for each

optional setting. In the table above we have used numbers that represent the ‘ﬁrst letters’ of the optional feature

name. For example, Read-Only = 7 (pqRs) 6 (mnO).

Admin can override User Read/Write settings by enabling/disabling Read/Write in Admin mode.

Instructions LED LED State

1. Unlock the datAshur Personal2 with User PIN Red solid LED changing to Green solid LED

indicating successful User PIN entry

2. Press the KEY button three times (treble-click)

& Green and Blue LED’s blinking together

3. Within 10 seconds begin to Press the number 7 (pqRs)

button followed by the number 9 (Wxyz) button (79) & Green and Blue LED’s continue to blink together

4. Press KEY button once

Red solid LED changing to Green solid LED.

When the datAshur Personal2 is inserted into a

USB port a solid Green LED indicates the

datAshur Personal2 is Read/Write enabled

Restricted write protect (Read-Only) access can be turned off with access restored to Read/Write.

This is done by performing the following Steps.

Once activated, access is restored to the default Read/Write state.

Note: Admin can override User Read/Write settings by enabling/disabling Read/Write in Admin mode.

#10

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com

8. How to set the Timeout Lock in User mode

To protect against unauthorised access when the datAshur Personal2 is connected to a host and unattended, the datAshur

Personal2 can be set to automatically lock after a pre-set amount of time.

In its default state, the datAshur Personal2 Timeout Lock feature is turned off. The Timeout Lock feature can be set to activate

(lock) anywhere between 1 and 99 minutes.

To set the Timeout Lock, please follow steps in the table below.

Instructions LED LED State

1. Unlock the datAshur Personal2 with User PIN Red solid LED changing to Green solid LED

indicating successful User PIN entry

2. Enable Options by pressing the KEY button 3 times -

treble click & Green and Blue LED’s blinking together

awaiting new instructions in OPTIONS mode.

3. Within 10 seconds begin to Press button number 8

(Tuv) followed by the number 5 (jkL) button - (85) & Green and Blue LED’s continue to blink together

4. Press KEY button once Blinking Green LED

5. Within 10 seconds begin enter the length of User

Timeout in 2 digits:

00 = 0 minutes (default)

01 = 1 minute

99 = 99 minutes etc

Green LED continues to blink

6. Press the Key button once Red solid LED changing to Green solid LED -

Admin can override USER Timeout Lock

9. How to disable the Timeout Lock in User Mode

Instructions LED LED State

1. Unlock the datAshur Personal2 with User PIN Red solid LED changing to Green solid LED

indicating successful User PIN entry

2. Enable Options by pressing the KEY button 3 times -

treble click & Green and Blue LED’s blinking together

awaiting new instructions in OPTIONS mode.

3. Within 10 seconds begin to Press button number 8

(Tuv) followed by the number 5 (jkL) button - (85) & Green and Blue LED’s continue to blink together

4. Press KEY button once Blinking Green LED

5. Within 10 seconds begin to press the number 0 button

twice (double click) (zero,zero)-(00) Green LED continues to blink

6. Press the Key button once Red solid LED changing to Green solid LED -

Timeout Lock has been disabled

To disable the Timeout Lock, please follow steps in the table below.

#11

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

11. How to create an Admin PIN

An Admin PIN is a useful feature for corporate deployment, for example:

• Recovering data from a drive and conﬁguring a new User PIN in the event an employee has forgotten their PIN

• Retrieving data from a drive if an employee leaves the company

• Setting policies such as ‘Read-Only’

• The Admin PIN can be used to override all User settings

PIN requirements:

• Must be between 7-15 digits in length

• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)

• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)

Instructions LED LED State

1. Unlock the datAshur Personal2 with User PIN Red solid LED changing to Green solid LED

indicating successful User PIN entry

2. Enable Options by pressing the KEY button 3 times -

treble click & Green and Blue LED’s blinking together

awaiting new instructions in OPTIONS mode.

3. Within 10 seconds begin to Press button number 8

(tuV) followed by the number 6 (mNo) button - (86) & Green and Blue LED’s continue to blink together

4. Press KEY button once

Red, Green & Blue LED’s will quickly blink

together once followed by the Red LED blinking

to the most signiﬁcant digit of revision and

the Green LED will blink according to the least

signiﬁcant digit of the revision number

For example, if the revision number is ‘1.11’, the Red LED will blink once (1) and the Green LED will blink eleven (11)

times. Once the sequence has ended the Red, Green & Blue LED’s will blink together once and then to solid Green.

10. How to determine the device Version Number in User mode

To display the device Version Number of the datAshur Personal2 do the following.

#12

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com

Instructions LED LED State

1. Press KEY button once

Red, Green & Blue LED’s will ﬂash together once

and then the Red LED will continue to blink

(if Blue LED also blinks this indicates an Admin

PIN has been set up)

2. Within 10 seconds begin to enter your User PIN (default

PIN 11223344) Red LED will continue to blink

3. Press the KEY button once Red solid LED changing to Green solid LED

indicating successful User PIN entry

4. Press and hold down the number 1 button and press

the KEY button twice (double click) (1 & ) &

Red and Blue LED’s ﬂicker together ready to

receive new Admin PIN

5. Within 10 seconds begin to enter your new Admin PIN & Red and Blue LED’s continue to ﬂicker together

6. Press KEY button twice (double click) Green LED blinks

7. Within 10 seconds begin to re-enter your new Admin PIN Green LED continues to blink

8. Press KEY button twice (double click) Red solid LED changing to Green solid LED

indicating successful Admin PIN entry

12. How to unlock the datAshur Personal2 as Admin

Instructions LED LED State

1. Press and hold down the number 1 button and press the

KEY button once (1 & ) & Red and Green LED’s ﬂicker together

2. Within 10 seconds begin to enter your Admin PIN & Red and Green LED’s continue to ﬂicker together

3. Press the KEY button once Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we

highly recommend that a new User PIN be created immediately once the drive has been unlocked

using the Admin PIN. Refer to section 13 on page 12.

Note: Once the datAshur Personal2 has been successfully unlocked, the Green LED will remain on for 30 seconds

only, during which time the datAshur Personal2 needs to be connected to a USB port. It can be locked down imme-

diately by pressing and holding down the KEY button for 3 seconds, or waiting for the 30 seconds to expire

or by clicking the ‘Safely Remove Hardware/Eject’ icon within your operating system.

13. How to create a New User PIN in Admin mode

Creating a new User PIN in Admin mode will become necessary if the datAshur Personal2 has been unlocked for any reason

with the Admin PIN, as this will automatically clear the User PIN. To create a new User PIN in Admin mode please follow the

instructions on the table below.

#13

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

Instructions LED LED State

1. Unlock the datAshur Personal2 with Admin PIN Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

2. Press the KEY button twice (double-click) Blue LED blinking ready to receive new PIN

3. Within 10 seconds begin to enter your New User PIN Blue LED continues to blink

4. Press KEY button twice (double-click) Green LED blinks

5. Within 10 seconds begin to re-enter the New User PIN Green LED continues to blink

6. Press KEY button twice (double-click) Off Red LED quickly fades out to indicate

successful creation of a New User PIN

Admin PIN requirements:

• Must be between 7-15 digits in length

• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)

• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)

14. How to change the Admin PIN

Once an Admin PIN has been created, the datAshur Personal2 needs to be unlocked in Admin mode in order to change the

Admin PIN. The Admin PIN cannot be changed from the User mode.

Instructions LED LED State

1. Unlock the datAshur Personal2 with existing Admin PIN Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

2. Press and hold down the number 1 button and press the

KEY button twice (double-click) (1 & ) & Red and Blue LED’s ﬂicker together ready to

receive new Admin PIN

3. Within 10 seconds begin to enter your New Admin PIN & Red and Blue LED’s continue to ﬂicker together

4. Press KEY button twice (double-click) Green LED blinks

5. Within 10 seconds begin to re-enter the New Admin PIN Green LED continues to blink

6. Press KEY button twice (double-click) Red solid LED changing to a ﬂickering Green

LED indicating successful Admin PIN change

Admin PIN requirements:

• Must be between 7-15 digits in length

• Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)

• Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)

Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we

highly recommend that a new User PIN be created immediately once the drive has been unlocked

using the Admin PIN. Refer to section 13 on page 12.

Note: If a mistake was made while deﬁning a new Admin PIN or the procedure was not completed, the drive

will retain the old Admin PIN.

#14

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com #14

www.istorage-uk.com

16. How to enable Read-Only in Admin mode

Instructions LED LED State

1. Unlock the datAshur Personal2 with Admin PIN Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

2. Press the KEY button three times

(treble-click) & Green and Blue LED’s ﬂicker together

3. Within 10 seconds begin to press the number 7 (pqRs)

button followed by the number 6 (mnO) button (76) & Green and Blue LED’s continue to ﬂicker

together

4. Press KEY button once

Red solid LED changing to ﬂickering Green

LED. when the datAshur Personal2 is inserted

into a USB port the Green LED blinks every two

seconds indicating the datAshur Personal2 is in

Read-Only mode

17. How to enable Read/Write in Admin mode

When Admin writes content to the datAshur Personal2 and restricts access to read-only, the User cannot change this setting in

User mode. To set the datAshur Personal2 to Read-Only, please follow the steps below.

Admin can override User set Read-Only by enabling Read/Write on the datAshur Personal2 using the Admin PIN. To set the

datAshur Personal2 to Read/Write, please follow the steps below.

15. How to verify whether an Admin/User PIN has been set up

1. Press KEY button once Red, Green & Blue LED’s will ﬂash together once, then one of the following states occurs.

Only User/default PIN exists Red LED blinks

Only Admin PIN exists Blue LED blinks

Both User and Admin PIN’s exist & Red and Blue LED’s blink together

The following table illustrates how to determine which PINs, User and/or Admin, have been set up.

With the datAshur Personal2 in a locked state (all LEDs off), press the KEY button once.

Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we

highly recommend that a new User PIN be created immediately once the drive has been unlocked

using the Admin PIN. Refer to section 13 on page 12.

Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we

highly recommend that a new User PIN be created immediately once the drive has been unlocked

using the Admin PIN. Refer to section 13 on page 12.

#15

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

#15 www.istorage-uk.com

18. How to determine the device Version Number in Admin mode

Instructions LED LED State

1. Unlock the datAshur Personal2 with Admin PIN Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

2. Press the KEY button three times

(treble-click) & Green and Blue LED’s ﬂicker together

3. Within 10 seconds begin to press the number 8 (tuV)

button followed by the number 6 (mNo) button (86) & Green and Blue LED’s continue to ﬂicker

together

4. Press KEY button once

Red, Green & Blue LED’s will quickly blink

together once followed by the Red LED blinking

to the most signiﬁcant digit of revision and

the Green LED will blink according to the least

signiﬁcant digit of the revision number

For example, if the revision number is ‘1.11’, the Red LED will blink once (1) and the Green LED will blink eleven (11)

times. Once the sequence has ended the Red, Green & Blue LED’s will blink together once and then to ﬂickering Green LED.

Instructions LED LED State

1. Unlock the datAshur Personal2 with Admin PIN Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

2. Press the KEY button three times

(treble-click) & Green and Blue LED’s ﬂicker together

3. Within 10 seconds begin to press the number 7 (pqRs)

button followed by the number 9 (Wxyz) button (79) & Green and Blue LED’s continue to ﬂicker

together

4. Press KEY button once

Red solid LED changing to ﬂickering Green

LED. when the datAshur Personal2 is inserted

into a USB port the Green LED is solid

indicating the datAshur Personal2 is Read/Write

enabled

To display the device Version Number of the datAshur Personal2 do the following.

Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we

highly recommend that a new User PIN be created immediately once the drive has been unlocked

using the Admin PIN. Refer to section 13 on page 12.

#16

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com #16

www.istorage-uk.com

19. How to set the Timeout Lock in Admin mode

Instructions LED LED State

1. Unlock the datAshur Personal2 with Admin PIN Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

2. Press the KEY button 3 times

(treble click) & Green and Blue LED’s ﬂicker together

awaiting new instructions in OPTIONS mode.

3. Within 10 seconds begin to press button number 8

(Tuv) followed by the number 5 (jkL) button - (85) & Green and Blue LED’s continue to ﬂicker

together

4. Press KEY button once Blinking Green LED

5. Within 10 seconds begin to enter the length of User

Timeout in 2 digits:

00 = 0 minutes (default)

01 = 1 minute

99 = 99 minutes etc

Green LED continues to blink

6. Press the Key button once Red solid LED changing to ﬂickering Green

LED. Admin can override USER Lock Timeout

To protect against unauthorised access when the datAshur Personal2 is connected to a host and unattended, the datAshur

Personal2 can be set to automatically lock after a pre-set amount of time.

In its default state, the datAshur Personal2 Timeout Lock feature is turned off. The Timeout Lock feature can be set to

activate (lock) anywhere between 1 and 99 minutes. Admin Timeout Lock settings will override User settings.

To set the Timeout Lock please follow steps in the table below.

Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we

highly recommend that a new User PIN be created immediately once the drive has been unlocked

using the Admin PIN. Refer to section 13 on page 12.

#17

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

#17 www.istorage-uk.com

Instructions LED LED State

1. Unlock the datAshur Personal2 with Admin PIN Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

2. Press the KEY button 3 times (treble-click)

& Green and Blue LED’s ﬂicker together

3. Within 10 seconds begin to press the number 3 (Def)

button followed by the number 2 (Abc) button (32) & Green and Blue LED’s continue to ﬂicker

together

4. Press KEY button once / Red and Green LED’s blink alternately

5. Within 10 seconds begin to enter your Admin PIN again / Red and Green LED’s continue to blink

alternately

6. Press KEY button once

Red solid LED to Red & Green solid LED’s to a

Green ﬂickering LED indicating that all data has

been deleted

21. How to delete all ﬁles in Admin mode

In the event that Admin wants to delete all data stored on the datAshur Personal2, please follow the instructions below. All

Admin settings will remain on the datAshur Personal2 but all data will be deleted and cannot be retrieved and the datAshur

Personal2 will have to be reformatted (see section 25 or 26)

Caution: Entering the Admin PIN to access a locked drive will clear the User PIN. For security reasons, we

highly recommend that a new User PIN be created immediately once the drive has been unlocked

using the Admin PIN. Refer to section 13 on page 12.

Instructions LED LED State

1. Unlock the datAshur Personal2 with Admin PIN Red solid LED followed by a ﬂickering Green

LED indicating successful Admin PIN entry

2. Enable Options by pressing the KEY button 3 times -

treble click & Green and Blue LED’s ﬂickering together

awaiting new instructions in OPTIONS mode.

3. Within 10 seconds begin to Press button number 8

(Tuv) followed by the number 5 (jkL) button - (85) & Green and Blue LED’s continue to ﬂicker

together

4. Press KEY button once Blinking Green LED

5. Within 10 seconds begin to press the number 0 button

twice (zero,zero) - (00) Green LED continues to blink

6. Press the Key button once Red solid LED changing to ﬂickering Green

LED. Timeout Lock has been disabled

20. How to disable the Timeout Lock in Admin Mode

To disable the Timeout Lock, please follow steps in the table below.

#18

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com

23. How to Reset the datAshur Personal2

In the event both the Admin and User PINs have been forgotten, or the user wants to delete all data stored on the datAshur

Personal2, please follow the instructions below.

The reset process will clear all cryptographic parameters including both User and Admin PINs. This means the datAshur

Personal2 will revert back to the default User PIN set as11223344 - see section 4 on page 7 on how to change the User PIN.

Also, since this will force the creation of a new encryption key, the datAshur Personal2 will have to be reformatted (see section

25 or 26).

Caution: Resetting the datAshur Personal2 will delete all data stored on the drive.

PINs Set-up

on datAshur

Personal2

PIN used to unlock

datAshur Personal2What happens after 10 consecutive incorrect PIN entries?

Admin & User

PINs User PIN

The datAshur Personal2 brute force mechanism will trigger and the User PIN

will be deleted.

All data will remain on the datAshur Personal2 and can only be accessed by

the Admin entering the correct Admin PIN.

Admin & User

PINs Admin PIN The datAshur Personal2 brute force mechanism will trigger and both the User

and Admin PINs, the encryption key and all data will be deleted and lost

forever.

User PIN Only User PIN The datAshur Personal2 brute force mechanism will trigger and the User PIN,

the encryption key along with all data will be deleted and lost forever.

Admin PIN Only Admin PIN The datAshur Personal2 brute force mechanism will trigger and the Admin

PIN, the encryption key along with all data will be deleted and lost forever.

If both Admin and User PINs have been created and a User enters an incorrect User PIN 10 (ten) consecutive times, the

datAshur Personal2 brute force mechanism will trigger and the User PIN will be deleted. All data will remain on the datAshur

Personal2 and can only be accessed by the Admin entering the correct Admin PIN.

If Admin enters an incorrect Admin PIN 10 (ten) consecutive times, then both the User and Admin PINs, the encryption key

and all data will be deleted and lost forever. The datAshur Personal2 will then revert back to factory default settings and will

need to be formatted before it can be reused.

The table below illustrates the different PIN set-up states and what happens when entering an incorrect Admin or User PIN

incorrectly 10 (ten) consecutive times.

The datAshur Personal2, unlike other similar drives, incorporates a random number generator, once the drive is reset a new

encryption key is randomly generated.

22. Brute Force Hacking Detection

#19

www.istorage-uk.com

iStorage datAshur® Personal2 Manual – v 2.2

25. How to conﬁgure the datAshur Personal2 with Windows OS

In the event that hacking detection has been triggered by entering the incorrect PIN 10 times in succession or the drive

has been reset, all data on the drive will be lost forever. Once a New User PIN has been created, the datAshur

Personal2 will need to be initialised and formatted.

To initialise your datAshur Personal2, do the following:

1. Create a New User PIN (see section 4).

2. Unlock the datAshur Personal2 by entering the New User PIN and connect to a computer’s USB port.

Instructions LED LED State

1. Press and hold down number 7 (seven) button and then

press the KEY button and release buttons

(7 & )

/ Red and Green LED’s blink alternately

2. Within 10 seconds begin to Press the number 9 button

three times (triple click) (999) / Red and Green LED’s continue to blink

alternately

3. Press and hold down number 7 (seven) button and then

press the KEY button and release buttons

(7 & )

Solid Red and Green LED’s change to a solid

Red LED that fades out to complete the reset

process

4. Proceed by clicking on Format disk.

Select FAT32 or NTFS depending on your needs, enter a Volume Label and click Start.

3. The computer should notify the user with the following message:

24. Booting from the datAshur Personal2

iStorage datAshur Personal2 USB drives are equipped with a boot delay feature in order to accommodate power cycling

during a host boot process.

There may be occasions where you might want to boot from the datAshur Personal2 for various reasons. When booting from

the datAshur Personal2, you are running your computer with the operating system that’s installed on the datAshur Personal2.

No special actions are required on the part of the user, and to use this feature, simply unlock the drive and connect to the USB

port of a host computer.

To force an immediate lock, always unplug to remove USB power to the datAshur Personal2.

OFF

#20

iStorage datAshur® Personal2 Manual – v 2.2

www.istorage-uk.com

5. Click OK to continue with formatting the drive.

6. The procedure will ﬁnish formatting the drive and conﬁrm that formatting has been completed.

While the datAshur Personal2 is formatting the BLUE LED will be ﬂashing.

Once ﬁnished, the BLUE LED becomes solid and your datAshur Personal2 is ready for use.

Warning: This procedure will erase ALL data on the drive.

In case that the formatting wizard does not appear, please follow the procedure below:

1. Windows 7: Right click Computer and then click Manage and then select Disk Management

Windows 8: Right click left corner of desktop and select Disk Management

Windows 10: Right click on the start button and select Disk Management

2. In the Computer Management window under the Disk Management tab, the datAshur Personal2 is

recognised as a removable device in raw format.

3. In the blank area under the unallocated section right click Removable Raw Drive and select Format.

La page charge ...

iStorage Datashur Personal2 Manuel utilisateur

iStorage Datashur Personal2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents