dji Mavic 3 Cine Mode d'emploi

Mavic 3 Cine
dji
Marque
dji
Modèle
Mavic 3 Cine
Taper
Mode d'emploi
Mavic 3 Cine Quick Start Guide
v1.0 2021.07
Aircraft
The MAVICTM 3 features Omnidirectional Obstacle Sensing, an Infrared Sensing System, and a fully
stabilized 3-axis gimbal with both telephoto and wide camera that can shoot up to 5.2K video and
20-megapixel photos. DJI signature technologies such as Obstacle Avoidance and Intelligent Flight
Modes like HyperLapse, ActiveTrack, QuickShot, Panorama, and Advanced Pilot Assistance Systems,
help you capture complex shots effortlessly.
1. Gimbal and Camera
A. Telephoto Camera
B. Wide Camera
2. Forward Vision System
3. Backward Vision System
4. Auxiliary Bottom Light
5. Downward Vision System
6. Infrared Sensing System
7. Front LEDs
8. Motors
9. Propellers
10. Aircraft Status Indicator
11. Landing Gear (antennas included)
12. Upward Vision System
13. Intelligent Flight Battery
14. Battery Level LEDs
15. Power Button
16. Battery Buckles
17. Charging/Upgrading Port (USB-C)
18. microSD Card Slot
Remote Controller
The DJI Smart Controller V2.0 features O3, the latest version of DJI’s signature OCUSYNCTM image
transmission technology, and can transmit a live HD view from the camera of an aircraft at a
distance of up to 15 km. Users can connect to the internet via Wi-Fi or by using a 4G dongle and
the Android operating system comes with a variety of functions such as Bluetooth and GNNS.
The built-in 5.5-in high brightness 1000 cd/m2 screen boasts a resolution of 1920×1080 pixels while
the remote controller comes with a wide range of aircraft and gimbal controls as well as
customizable buttons and has a maximum operating time of 3 hours.
1. Antennas
2. Back Button/Function Button
3. Control Sticks
4. RTH Button
5. Flight Pause Button
6. Flight Mode Switch
7. 5D Button
8. Power Button
9. Confirm Button/Customizable Button C3
10. Touchscreen
11. microSD Card Slot
12. USB-C Port
13. Mini HDMI Port
14. Gimbal Dial
15. Record Button
16. Status LED
17. Battery Level LEDs
18. Focus/Shutter Button
19. Camera Settings Dial
20. Air Vent
21. Control Sticks Storage Slots
22. Customizable C1 Button
23. Speaker
24. Customizable C2 Button
25. Air Intake
Download the DJI Fly App and Watching Tutorial Videos
Charging the Batteries
Checking the Battery Levels and Powering On/Off
Press once to check the battery level.
Press, then press and hold to turn on/off.
Preparing the Aircraft
1. Unfold the front arms and the propellers.
2. Unfold the rear arms and the propellers.
3. Match the propellers to motors. Press the propellers down firmly and rotate in the lock
direction.
Marked
Unmarked
4. Unfolded
Unfold the front arms and the propellers before the rear ones. All arms and propellers
must be unfolded before takeoff.
Preparing the Remote Controller
1. Remove the control sticks from the storage slots, then attach the control sticks.
2. Unfold the antennas.
Ensure the control sticks are firmly mounted.
Preparing for Takeoff
1. Power on the remote controller
2. Power on the aircraft
3. Launch DJI Fly App
Flight
• Remote Controller Operation
Specifications
• Aircraft (Model: L2P/L2A)
＜920 g
46 minutes (0 wind while flying at a consistent 15.5 mph (25 kph))
14° to 104°F (-10° to 40°C)
2.400-2.4835 GHz; 5.725-5.850 GHz
2.4GHz: ≤28.83 dBm (FCC), ≤20 dBm (CE/SRRC/MIC)
5.8GHz: ≤29.9 dBm (FCC), ≤14 dBm (CE), ≤29 dBm (SRRC)
Wi-Fi
WiFi Direct, Wi-Fi Display, 802.11b/a/g/n/ac/ax
2×2 MIMO
2.400-2.4835 GHz; 5.725-5.850 GHz
2.4 GHz: ≤20.11 dBm (FCC); ≤18.5 dBm (CE/SRRC/MIC/KCC)
5.8 GHz: ≤19.11 dBm (FCC/SRRC); ≤12.5 dBm (CE/KCC)
Bluetooth
Bluetooth 5.1
2.400-2.4835 GHz
≤5.98 dBm
• Camera
Telephoto Camera
1/2’’ CMOS; Effective pixels: 12M
Wide Camera
4/3’’ CMOS; Effective pixels: 20M
Telephoto Camera
FOV: 15°
35mm format equivalent: 160 mm
Aperture: f/4.4
Focus: 3 m to ∞
Wide Camera
FOV: 84°
35mm format equivalent: 24 mm
Aperture: f/2.8-f/11
Focus: 1 m to ∞
Telephoto Camera
Video: 100-3200 (auto)
Photo: 100-3200 (auto)
Wide Camera
Video: 100-6400
Photo: 100-3200 (auto), 100-12800 (manual)
Telephoto Camera
Electronic: 1-1/8000 s
Wide Camera
Mechanic: 8-1/2000 s
Electronic: 8-1/8000 s
• Remote Controller (Model: RM510)
Approx. 750 g
18650 Li-ion (5000 mAh @ 7.2 V)
OcuSync 3.0
2.400-2.4835 GHz; 5.725-5.850 GHz
2.4GHz: ≤31.5 dBm (FCC), ≤20 dBm (CE/SRRC/MIC)
5.8GHz: ≤32 dBm (FCC), ≤14 dBm (CE), ≤21 dBm (SRRC)
Wi-Fi
WiFi Direct, Wi-Fi Display, 802.11b/a/g/n/ac/ax
2×2 MIMO
2.400-2.4835 GHz; 5.725-5.850 GHz
2.4 GHz: ≤23 dBm (FCC); ≤18.5 dBm (CE/SRRC/MIC/KCC)
5.8 GHz: ≤24 dBm (FCC/SRRC); ≤12.5 dBm (CE/KCC)
Bluetooth
Bluetooth 5.1
2.400-2.4835 GHz
≤6 dBm
• Intelligent Flight Battery
5000 mAh
LiPo 4S
77 Wh
41° to 113°F (5° to 45°C)
88 W
For more information, read the User Manual: http://www.dji.com/mavic-3
※ This content is subject to change without prior notice.
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
ISED compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
• For Aircraft (Model: L2P/L2A)
• This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm between the
radiator and your body.
• Cet équipement est conforme aux limites d'exposition aux radiations FCC/IC CNR-102 établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm
entre le radiateur et votre corps.
• For Remote Controller (Model: RM510)
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user
must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal
Communications Commission (USA). These requirements set a SAR limit of 4W/kg averaged over 10 gram of tissue.
The highest SAR value reported under this standard during product certification for extremity condition.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established
by the ISED. These requirements set a SAR limit of 4W/kg averaged over 10 gram of tissue. The
highest SAR value reported under this standard during product certification for extremity condition.
Cet équipement est conforme aux limites d'exposition aux rayonnements de l'ised pour les
environnements non contrôlés.L'utilisateur final doit se conformer à des instructions d'exploitation
spécifiques afin de respecter la conformité à l'exposition aux radiofréquences.Cet émetteur ne doit
pas être au même endroit ni fonctionner avec une autre antenne ou un autre émetteur.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

dji Mavic 3 Cine Mode d'emploi

Mavic 3 Cine
dji
Marque
dji
Modèle
Mavic 3 Cine
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents