Centerline HMM10 Mixer Manuel utilisateur

Marque: Centerline

Modèle: HMM10 Mixer

Catégorie: Mélangeurs

Taper: Manuel utilisateur

701 S. RIDGE AVENUE

TROY, OHIO 45373

937-332-3000

www.hobartcorp.com

INSTRUCTION

MANUAL

MODEL

HMM10

FORM 48170 (May 2023)

– 2 –

TABLE OF CONTENTS

GENERAL ............................................................................................................................................. 3

INSTALLATION .................................................................................................................................... 3

Unpacking ........................................................................................................................................ 3

Location ........................................................................................................................................... 3

Electrical Connections (Cord Connected Mixers) ............................................................................ 4

Check Initial Operation .............................................................................................................. 4

OPERATION ........................................................................................................................................ 5

STANDARD CONTROLS .................................................................................................................... 6

Model HMM10 (With Three Mix Speeds)......................................................................................... 6

Mixer Speeds ................................................................................................................................... 6

Button Function Description ............................................................................................................ 6

BOWL PLACEMENT ........................................................................................................................... 7

Agitator ............................................................................................................................................ 7

To Install ..................................................................................................................................... 7

To Remove ................................................................................................................................. 7

Prepare For Mixing .......................................................................................................................... 8

Mixing Modes .................................................................................................................................. 8

Timed Mixing Mode ......................................................................................................................... 9

Operating Notes .............................................................................................................................. 9

Unloading ...................................................................................................................................... 10

Wire Cage Assembly ..................................................................................................................... 10

Remove and Clean Bowl Guard Wire Cage .............................................................................11

Reinstall Bowl Guard Wire Cage ..............................................................................................11

Agitators and Attachments ............................................................................................................. 12

CLEANING ......................................................................................................................................... 13

MAINTENANCE ................................................................................................................................. 14

Lubrication ..................................................................................................................................... 14

Slideways ................................................................................................................................. 14

Planetary Seal ......................................................................................................................... 14

Adjustments ................................................................................................................................... 15

Agitator Clearance ................................................................................................................... 15

Measure Clearance ................................................................................................................. 15

Adjust the Bowl/Agitator Clearance ......................................................................................... 15

TROUBLESHOOTING ...................................................................................................................... 16

Service ........................................................................................................................................... 16

– 3 –

Installation, Operation and Care of

Centerline by Hobart 10-Quart Mixer

SAVE THESE INSTRUCTIONS

GENERAL

The Centerline by Hobart 10-quart mixer is a bench-type mixer which features three-speeds, a digital

timer, a manual bowl lift, and a #12 attachment hub as standard equipment.

A variety of attachments, agitators, and accessories are available. These are described in the Agitators

and Attachments section of this manual.

INSTALLATION

UNPACKING

The mixer was inspected before leaving the factory. The carrier assumes full responsibility for safe delivery

upon acceptance of the shipment. Check for possible shipping damage immediately after receipt.

If the mixer is found to be damaged, complete the following steps:

 1.Carriermustbenotiedwithinvebusinessdaysofreceipt.

 2.Carrier’slocalterminalmustbenotiedimmediatelyupondiscovery(notethetime,date,andwho

wasspokento),andfollowupandconrmwithwrittenorelectroniccommunication.

3. All original packing materials must be kept for inspection purposes.

 4.Themixercannothavebeenmoved,installed,ormodied.

5. Notify Hobart customer care at (800) 333-7447.

LOCATION

Priortoinstallation,testtheelectricalservicetoensureitagreeswiththespecicationsonthemixerdata

plate.

Place the mixer on a suitable sturdy level surface. There should be adequate space around the mixer for

the user to operate the controls and to install and remove bowls.

– 4 –

ELECTRICAL CONNECTIONS (Cord Connected Mixers)

The electrical cord on this mixer is equipped with a three-pronged grounding plug

which must be connected to a properly grounded receptacle. If the receptacle is not the proper

grounding type, contact an electrician. DO NOT remove the grounding prong from the plug.

Electrical and grounding connections must comply with the applicable portion of

the National Electrical Code and/or other local electrical codes.

Check Initial Operation

1. Apply power to the mixer by inserting the cord plug into a properly grounded outlet.

2. Mixer will beep three times indicating mixer is ready.

3. Install the bowl on the bowl support and raise into the mix position, with the bowl support up and

bowl guard wire cage closed.

4. Turn the speed gear shift lever to 1.

5. Run the mixer by pushing the ON/OFF button.

– 5 –

OPERATION

Moving agitator in bowl. Keep hands, clothing and utensils out of bowl while in

operation. Do not use without interlocked guards.

The Centerline by Hobart mixers are equipped with a timer and controls. Refer to Fig. 1 for operating parts

and OPERATION section for their functions.

The bowl guard wire cage must be in closed position or the mixer will not operate.

The bowl must be mounted, and the bowl support must be raised (mix position) or the mixer will not operate.

Fig. 1

CONTROLS

ATTACHMENT

HUB

DRIP CUP

BOWL GUARD

WIRE CAGE

AGITATOR

SPLASH

GUARD

BOWL

SUPPORT

APRON

– 6 –

STANDARD CONTROLS

MODEL HMM10 (With Three Mix Speeds)

MIXER SPEEDS

SPEED 1 (Low) This speed is for heavy mixtures such as heavy batters, potatoes, pizza

dough, and bread dough.

SPEED 2 (Medium) This speed is for mixing cake batters and mashing potatoes.

SPEED 3 (High) Thisspeedisforincorporatingairintolightbatches,aswellasnishing

whipped items.

BUTTON FUNCTION DESCRIPTION

NOTE: The mixer will beep once when any button is pressed.

ON/OFF Press the ON/OFF button to start the mixer. If the mixer is running,

press the ON/OFF button to stop the mixer.

SEC UP

ARROW

Press once to increase the time in 1 second increments. Press and

hold to quickly increase time until released. Range is 0-59.

SEC DOWN

ARROW

Press once to decrease the time in 1 second increments. Press and

hold to quickly decrease time until released. Range is 0-59.

MIN UP

ARROW

Press once to increase the time in 1 minute increments. Press and

hold to quickly increase time until released. Range is 0-59.

MIN DOWN

ARROW

Press once to decrease the time in 1 minute increments. Press and

hold to quickly decrease time until released. Range is 0-59.

NOTE: The seconds and minutes are set independently.

NOTE: The ON/OFF button is used to clear overload error.

Fig. 2

TIMER

DISPLAY

SECOND

MINUTE

SECOND

DOWN

MINUTE

DOWN

ON/OFF

SPEED GEAR

SHIFT LEVER

– 7 –

BOWL PLACEMENT

The bowl must be installed on the bowl support before the agitator is installed.

To install the bowl, lower the bowl support and move bowl clamps to the open position (Fig. 3). Position

the bowl so the alignment bracket on the back of the bowl is in the bowl retainer and the alignment pins

onthefrontofthebowlsupporttintheholesonthesidesofthebowl.Lockthebowlinplacebyrotating

the bowl clamps (Fig. 4).

AGITATOR

To install an agitator, the bowl must be on the bowl support.

To Install

1. Lower the bowl.

2. Open the bowl guard wire cage.

3. Place the agitator inside the bowl and align the horizontal slot on the agitator with the agitator shaft

pin.

4. Slide the agitator up the agitator shaft and turn it clockwise to seat the shaft pin in the slot of the

agitator shank.

To Remove

1. Open the bowl guard wire cage.

2. Lower the bowl.

 3.Lifttheagitatorandturnitcounterclockwise.Slideagitatordownandotheagitatorshaft.

Fig. 3 Fig. 4

– 8 –

PREPARE FOR MIXING

1. Place the mixing bowl on the bowl support.

2. Pour ingredients into the bowl.

3. Place the agitator inside the bowl, and then

attach it to the agitator shaft (Fig. 5).

4. Lift bowl support.

5. Correctly close the bowl guard wire cage.

6. The mixer is now ready for mixing.

UNTIMED MIXING MODES

1. Turn the speed gear shift lever (Fig. 6) to select a mix speed. The timer display reads OFF (Fig. 6).

NOTE: GearSafe™ protects gears if speeds are changed during mixing operation without stopping mixer.

2. Press the ON/OFF button (Fig. 7) to begin mixing. The timer display reads ON (Fig. 7).

NOTE: If the bowl guard wire cage is opened or the bowl is lowered at any time, the mixing operation

will stop. To resume the mixing operation, close the wire cage or raise the bowl and press the ON/OFF

button.

3. Press the ON/OFF button to stop the mixer. The timer display reads OFF.

4. Press the ON/OFF button to resume mixing operation if needed.

Fig. 5

Fig. 6 Fig. 7

SPEED GEAR

SHIFT LEVER

ON/OFF

BUTTON

– 9 –

TIMED MIXING MODE

1. Turn the speed gear shift lever (Fig. 6) to select a mix speed. The timer display reads OFF (Fig. 6).

2. Press the MIN UP/DOWN and SEC UP/DOWN arrows until the timer display reads the desired

mixing time (Fig. 8). This is the set time.

3. Press the ON/OFF button to begin mixing; the timer starts counting down from the set time.

4. To stop the mixer at any time, press the ON/OFF button. To resume mixing, press the ON/OFF

button. For example: The mixer is started at speed 1 for 30 seconds and is stopped after 10 seconds.

Pressing the ON/OFF button will resume the mixing operation and the remaining 20 seconds will

count down.

NOTE: If the wire cage is opened or the bowl is lowered at any time, the mixing operation will stop. To

resume the mixing operation, close the wire cage or raise the bowl and press the ON/OFF button.

5. When the timer reaches 00:00, the mixer stops and beeps three times. The count-down timer then

displays the last set time.

OPERATING NOTES

• If the mixer is stopped during a mixing operation, the timer also stops. The timer starts again (with

the time remaining) when the ON/OFF button is pressed (Fig. 8).

Fig. 8

ON/OFF

BUTTON

– 10 –

UNLOADING

1. Open the bowl guard wire cage assembly.

2. Lower bowl support.

3. Remove the agitator from the agitator shaft.

4. Open the bowl clamps.

 5.Liftthebowlothepinsandremovefromthebowlsupport.

WIRE CAGE ASSEMBLY

The bowl guard wire cage assembly can be rotated out-of-the-way to the left to add ingredients or to

access the bowl and agitator.

Note how the plastic carriers allow the wire cage to ride around the circumference of the planetary drip cup.

• Open the bowl guard wire cage; rotate it to your left (Fig. 9).

• Close the bowl guard wire cage; rotate it to your right until it stops in the closed position (Fig. 10).

NOTE: The bowl guard wire cage must be returned to the closed position for the mixer to operate.

Fig. 9 Fig. 10

– 11 –

Remove and Clean Bowl Guard Wire Cage

Lower the bowl. Rotate the wire cage assembly to the left until it is positioned underneath the splash guard.

Remove the agitator and bowl.

While holding the wire cage assembly with both hands, rotate it completely to the left. When the front-center

retainer(Fig.11)reachestheendofitstravel,itcanbeloweredthroughtheat(Fig.11)ontheridgeof

the drip cup (Fig. 11). After lowering the front-center retainer, move the wire cage assembly slightly to the

rear so the rear retainers clear the ridge on the drip cup. The wire cage assembly can now be lowered

and removed.

Wash the bowl guard wire cage assembly in a sink, rinse with clear water, and dry with a clean cloth.

Thesplashguardcanbewipedoand/orwashedwithaclothorspongeusingwarm,soapywater.Rinse

with clear water and dry with a clean cloth.

Reinstall Bowl Guard Wire Cage

Hold the wire cage assembly so its top ring is positioned around the planetary drip cup with the grooves

in both nylon rear retainers straddling the ridge on the drip cup at the rear. Lift the wire cage assembly so

thefront-centerretainerpassesupthroughtheatontheridgeofthedripcupandrotatethewirecage

assembly to the right. The wire cage assembly is properly assembled when all three retainers straddle

the ridge on the drip cup in three opposed locations. Rotate the wire cage assembly to the right until it

stops at the front-center position.

Rotate the wire cage out-of-the-way to the left to install or remove the agitator and bowl or to add ingredients.

Return the wire cage to its front-center position to operate the mixer.

Fig. 11

FRONT-CENTER

RETAINER RIDGE

DRIP CUP

FLAT

– 12 –

AGITATORS AND ATTACHMENTS

Flat Beater Wire Whip

Dough Hook Bowl (SST)

– 13 –

CLEANING

Unplug mixer power cord before beginning any cleaning procedure.

The mixer should be thoroughly cleaned daily. DO NOT use a hose to clean the mixer; it should be washed

with a clean, damp cloth. The base allows ample room for cleaning under the mixer. The apron (Fig. 1)

may be removed for cleaning by loosening the screws. The drip cup (Fig. 1) should be wiped clean. For

cleaning the bowl guard wire cage assembly, refer to page 11.

– 14 –

MAINTENANCE

Unplug mixer power cord before beginning any maintenance procedure.

LUBRICATION

Slideways

The slideways (Fig. 12) should be lubricated approximately twice a year. To reach these areas, fully lower

the bowl support and remove the apron (Fig. 12), which is secured by screws. Wipe a thin coat of Lubriplate

630AA on each slideway. Install the apron.

Planetary Seal

Occasionally, the planetary seal (Fig. 13) may

become dry and begin to squeak. To correct this,

work a little lubrication (mineral oil) under the lip

of the seal.

Fig. 12

SLIDEWAYS

APRON SCREWS

Fig. 13

PLANETARY

SEAL

– 15 –

ADJUSTMENTS

Agitator Clearance

The agitator clearance should be checked periodically. The agitator must not touch the bowl.

ThemaximumclearancebetweenthebottomofthebowlandtheBatbeateris1/8"(3mm).

Install a bowl and agitator (e.g., beater). If the bowl and beater come into contact before the bowl support

reaches its stop, adjust the stop screw. Refer to Adjust the Bowl/Agitator Clearance.

Measure Clearance

Pourenoughourinthebowltocoverthebottomofthebowlwherethebeatertravels.Withthebowlfully

raised(beatershouldnottouchthebottomofthebowl),brieyrunthemixeratthelowestspeed.

Turnothemixer,disconnecttheelectricalpowersupply,andmeasurethedepthofourwherethebeater

has traced a path. This measurement should be taken at several points around the bowl to assure accuracy.

Adjust the Bowl/Agitator Clearance

• Remove the apron (Fig. 14), which is secured by screws.

• Adjust the clearance by loosening the stop nut and moving the screw (Fig. 15) clockwise to increase

the clearance or counterclockwise to decrease the clearance.

• After the adjustments are made, tighten the stop nut and replace the apron, and secure it with the

screws.

• Carefully operate the bowl lift several times to check the adjustment.

Fig. 14 Fig. 15

STOP

NUT

SCREW

APRON SCREWS

– 16 –

TROUBLESHOOTING

Symptoms Possible Causes

Mixer will not start Flashing time display – see below.

Branch circuit protector is in open position - check

fuse or disconnect switch.

Mixer is overloaded.

Wire cage is not in the closed position.

Bowl is not in closed (mix) position or bowl is not

in up position.

Agitator touches bowl Improper agitator clearance - see Maintenance

for adjustment procedure.

Agitator is not installed properly.

Planetary seal squeaks Seal requires occasional lubrication - see

Maintenance.

Timerdisplayashingtimeandmachineis

beeping

Ifthetimerdisplayisashingandmachine

is beeping, press ON/OFF button to reset. If

symptom still exists, contact your local Hobart

Serviceoce.

Timer display reads OP (Fig. 16) Speed gear shift lever is not properly seated.

SERVICE

Ifserviceisneededonthisequipment,contactyourlocalHobartServiceoceat(888)4HOBART.

Fig. 16

SPEED GEAR

SHIFT LEVER

FORM 48170 (May 2023) PRINTED IN U.S.A.

701 S. RIDGE AVENUE

TROY, OHIO 45373

937-332-3000

www.hobartcorp.com

MANUAL DE

INSTRUCCIONES

MODELO

HMM10

FORMULARIO 48170 (Mai de 2023)

– 2 –

TABLA DE CONTENIDO

GENERAL ............................................................................................................................................. 3

INSTALACIÓN ..................................................................................................................................... 3

Desembalaje .................................................................................................................................... 3

Ubicación ......................................................................................................................................... 3

Conexiones eléctricas (Batidoras conectadas con cable) ............................................................... 4

Revisión inicial de operación ..................................................................................................... 4

OPERACIÓN ........................................................................................................................................ 5

CONTROLES ESTÁNDAR ................................................................................................................. 6

Modelo HMM10 (con tres velocidades de batido) ........................................................................... 6

Velocidades de la batidora .............................................................................................................. 6

Descripción de la función de los botones ........................................................................................ 6

COLOCACIÓN DEL TAZÓN ............................................................................................................... 7

Batidor ............................................................................................................................................. 7

Para instalarlo ............................................................................................................................ 7

Para quitarlo .............................................................................................................................. 7

Preparación para mezclar ............................................................................................................... 8

Modos de mezclado no programado ............................................................................................... 8

Modo de mezclado programado ...................................................................................................... 9

Notas de funcionamiento ................................................................................................................. 9

Descarga ....................................................................................................................................... 10

Montaje de la rejilla del tazón ........................................................................................................ 10

Cómo retirar y limpiar la rejilla de la guarda del tazón..............................................................11

Cómo volver a colocar la rejilla del tazón .................................................................................11

Batidores y aditamentos ................................................................................................................ 12

LIMPIEZA ........................................................................................................................................... 13

MANTENIMIENTO ............................................................................................................................. 14

Lubricación .................................................................................................................................... 14

Guías ....................................................................................................................................... 14

Sello planetario ........................................................................................................................ 14

Ajustes ........................................................................................................................................... 15

Espacio libre del batidor .......................................................................................................... 15

Medida del espacio libre .......................................................................................................... 15

Ajuste del espacio libre del tazón y del batidor........................................................................ 15

RESOLUCIÓN DE PROBLEMAS ..................................................................................................... 16

Servicio .......................................................................................................................................... 16

– 3 –

Instalación, funcionamiento y cuidado de

la batidora Centerline de 10 cuartos de galón por

Hobart

CONSERVE ESTAS INSTRUCCIONES

GENERAL

La batidora Centerline de 10 cuartos de galón por Hobart es una batidora de tipo banco que tiene tres

velocidades, un temporizador digital, una palanca de levantamiento manual del tazón y una entrada de

aditamentos n.° 12 como equipamiento estándar.

Están disponibles una variedad de aditamentos, batidores y accesorios. Estos elementos se describen

en la sección Batidores y aditamentos de este manual.

INSTALACIÓN

DESEMBALAJE

La batidora fue inspeccionada antes de salir de fábrica. El transportista asume total responsabilidad

por la entrega segura una vez aceptado el cargamento. Compruebe que no haya daños al cargamento

inmediatamente después de recibirlo.

Si la batidora está dañada, siga estos pasos:

 1.Noticaraltransportistadentrodeloscincodíashábilessiguientesalafechaderecepción.

 2.Noticardeinmediatoalaterminallocaldeltransportistatraseldescubrimiento(anotarlahora,la

fechaylapersonaconquiensehabló)yhacerunseguimientoyenviarlaconrmaciónmediante

comunicaciones escritas o electrónicas.

3. Conservar todos los materiales originales del embalaje por motivos de inspección.

 4.Labatidoranodebemoverse,instalarsenimodicarse.

 5.NoticaralServiciodeAtenciónalClientedeHobartal(800)333-7447.

UBICACIÓN

Antesdelainstalación,pruebeelservicioeléctricoparaasegurarsedequeconcuerdaconlasespecicaciones

de la placa de datos de la batidora.

Coloquelabatidorasobreunasupercieniveladayresistente.Debehaberespacioadecuadoalrededor

de la batidora para que el usuario opere los controles e instale y retire los tazones.

– 4 –

CONEXIONES ELÉCTRICAS (Batidoras conectadas con cable)

ADVERTENCIA

El cable eléctrico de esta batidora está equipado con un enchufe de conexión a

tierra con tres terminales que se deben conectar correctamente a una toma con conexión a tierra.

Si la toma corriente no es la correcta, comuníquese con un electricista. NO quite el terminal de

conexión a tierra del enchufe.

ADVERTENCIA

Las conexiones eléctricas y a tierra deben cumplir con la parte aplicable del Código

Eléctrico Nacional o de otros códigos eléctricos locales.

Revisión inicial de operación

1. Conecte la alimentación a la batidora insertando el enchufe del cable en una toma con conexión a

tierra apropiada.

2. La batidora emitirá tres pitidos para indicar que está lista.

3. Instale el tazón en el soporte del tazón y levántelo a la posición de mezclado con el soporte del

tazón y cierre la rejilla del tazón.

4. Lleve la palanca de cambio de velocidades a la posición 1.

5. Ponga en funcionamiento la batidora presionando el botón ON/OFF.

La page charge ...

Centerline HMM10 Mixer Manuel utilisateur

Marque: Centerline

Modèle: HMM10 Mixer

Catégorie: Mélangeurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Centerline HMM10 Mixer User manual
español: Centerline HMM10 Mixer Manual de usuario
português: Centerline HMM10 Mixer Manual do usuário

Documents connexes

Centerline CENTERLINE HMM20 Manuel utilisateur

Centerline HMM10 Mixer Manuel utilisateur

Centerline HMM10 Mixer Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents