Microlife PF 100 Digital Peak Flow Asthma Monitor Manuel utilisateur

Read the instructions carefully before using this device.

Veuillez lire attentivement les instructions avant d’utiliser ce

produit.

Vor Verwendung Bedienungsanleitung genau studieren.

Prima di utillizzare l’apparecchio leggere attentamente le istruzioni

per l’uso.

IB PF 100 4G S-V4 3323

Revision Date: 2023-07-14

Microlife Corporation

9F, 431, RuiGuang Road, NeiHu

Taipei 11492, Taiwan, China

www.microlife.com

Microlife UAB

P. Lukšio g. 32

08222 Vilnius / Lithuania

PF 100

EN

FR

1

17

DE

IT

29

42

Asthma monitor

1

Electronic Asthma Monitor

Instruction Manual

Important Safety Instructions

Type BF applied part

Batteries and electronic devices must be disposed of in accordance with

the locally applicable regulations, not with domestic waste.

Ensure that children do not use the device unsupervised; some parts are

small enough to be swallowed. Be aware of the risk of strangulation in case

this device is supplied with cables or tubes.

Keep dry

1

PF 100 2

Table of Contents

1. Introduction

2. Your Microlife Asthma Monitor

3. Preparation for your first measurement

3.1. Inserting the Batteries

3.2. Setting Date and Time

4. Carrying out a Measurement

5. Important Information for Measurement and Control

of your Peak Flow Values

6. Self-Assessment with the Traffic Light Scheme

7. Cleaning and Disinfecting

7.1. Cleaning / Disinfecting the Mouthpiece

7.2. Cleaning / Disinfecting the Measuring Tube

7.3. Cleaning the Main Unit

8. Memory Handling

9. Analysing Data using Computer Interface

10. Messages / Malfunctions / Errors

11. Battery Replacement

12. Care and Safety Information

13. Guarantee

14. Technical Specifications

15. www.microlife.com

EN

PF 100 2

3

1. Introduction

Your new Microlife Monitor is a high quality medical device that measures your

maximum possible exhalation which is called «peak flow» (referred to in medical

terms as PEF - Peak Expiratory Flow).

Regular monitoring of your peak flow is extremely useful for controlling diseases

of the airways such as asthma or chronic bronchitis. After the peak flow result is

shown, a further value (for FEV1) will then be indicated. This value is also of interest

for your doctor.

The measurements can be performed on your own, because the Microlife Monitor

is very simple to use. It is as suitable for children in the pre-school age as for the

elderly.

Because the device has an automatic memory of 240 data entries, you do not need

to note the values down; simply take the device with you the next time you visit

your doctor. The device can be connected to a computer, and the values can be

analysed by using the Microlife Asthma analyser software program.

Read through this instruction manual carefully before using the device and then

keep it in a safe place.

2. Your Microlife Asthma Monitor

The illustration shows the Microlife Asthma Monitor

3. Preparation for your first Measurement

Before your first use we recommend that you disinfect the mouthpiece as explained

in this manual.

Memory Scroll

Battery

Compartment

Mouth Piece

On/Off

Display

Data

Compartment

Measuring Tube

PF 100 4

3.1. Inserting the Batteries

1. Please open the Battery Compartment from

underneath and insert the two batteries (1.5V,

size AAA).

2. Please watch the polarity as indicated by the

symbols in the compartment.

3.2. Setting Date and Time

The monitor automatically records the time and

date of each measurement. After new batteries

have been inserted, the time/date display shows

the following setting: year: 2002; day 01, month 01

and time 00:00 o’clock.

You must then re-enter the date and current time.

To do this, proceed as follows (Example: Entering

15th June 2002, 09:50 o’clock):

1. Please open the Data Compartment from

underneath at the position of the data symbol

indication.

2. Press the small time switch next to the clock

symbol with a pen and «2002» starts blinking;

release the switch.

3. Using the two arrow keys on the front of the

monitor you can decrease (left arrow button)

or increase (right arrow button) the number.

Release the arrow button when the correct

number is reached.

5

4. Press the time switch again to confirm the

year setting and move to the month setting.

The month digits blink.

5. The current month can now be entered by

pressing the arrow button. (Example: pressing

5 times the right arrow button advances to 06

for June)

6. Press the time switch again to confirm the

month setting and move to the day setting.

The day digits blink.

7. The current day can now be entered by

pressing the arrow button. (Example: pressing

14 times the right arrow button advances to

15 for 15th June)

8. Press the time switch again to confirm the

day setting and move to the hour setting. The

hour digits blink.

9. The current hour can now be entered by the

arrow button. (Example: pressing 9 times the

right arrow button moves to 09 for 09 o’clock)

10. Press the time switch again to confirm the

hour setting and move to the minute setting.

The minute digits will now blink.

11. The current minutes can now be entered by

pressing the arrow button. (Example: pressing

9 times on the left arrow button moves to 50

for 09:50 o’clock).

12. Press the time switch again to confirm all

settings. Date and time are now stored, the

clock starts running and the monitor switches

to «ready» state condition which enable your

first measurement.

13. Close the data compartment.

PF 100 6

Please note:

• If you hold down the arrow key for more than 2 seconds it speeds up.

• Date /time can also be set easily from computer when you run the Microlife

Asthma Analyser Software.

4. Carrying out a Measurement

• When different people use this meter their individual readings cannot be

assigned to different users when the data is stored.

• If time/date is not set, measurements can not be performed.

• If another person intends to use the device permanently, all data from the

previous user should be erased as explained in this manual.

• In case another user has already used the monitor, we recommend

disinfecting the measuring tube as explained in this manual. In this case we

also recommend that each user uses a new mouthpiece. Extra mouthpieces

can be ordered through your Microlife dealer.

1. Press the ON/OFF button to turn the monitor

on. At first, the last result of the memory is

shown («0» if there are not yet data) and then

the device indicates «READY» for a measure-

ment by two short beeps and blinking arrows.

2. You can perform the measurement while

standing or sitting upright. For better compa-

rison of your data you should always perform

the measurement in a similar position.

3. Hold the monitor with both hands on the two

rubber areas (compartments).

4. Inhale completely and hold your breath for a

moment.

5. Cover the mouthpiece tightly with your lips.

6. Blow into the measuring tube as hard and as

fast as you can.

7

7. A long beep confirms that the result

is recorded. The peak flow value

is displayed for about 3 seconds,

then the FEV1 is shown. Afterwards

the monitor is ready for a new

measurement which is indicated by

two short beeps.

8. It is recommended to perform

three or more measurements

sequentially. Please note that the monitor only

saves the highest reading from switching the

device on until switching it off.

9. After each measurement, at first the actual

reading is shown in the display and then it

switches automatically to the highest reading

of your current measurement session.

10. Press the ON/OFF button to switch the

monitor off. Before the monitor switches off,

the highest value and its related memory

position «MR xx» is displayed.

11. Store the monitor in a clean and dust free place.

Traffic light indicator on the device

After the measurement, a small arrow in the display will

indicate if the reading is in the green, yellow or red range.

500 l/min is defined as reference value.

If a reading is above 80% (> 400 l/min) of the reference value, it will be indicated

in the green range. A reading in the yellow range indicates a reading between 60%

and 80% (300 l/min - 400 l/min) of the reference value. A reading in the red range

indicates a reading below 60% (< 300 l/min) of the reference value.

It would be best to determine the area limits together with your physician and when

required these ranges can be set manually within the software.

5. Important Information for Measurement and Control

of your Peak Flow Values

•

It is necessary to keep regular control of your peak flow values. Doctors generally

recommend taking one measurement in the morning and one in the evening, every

PF 100 8

day, normally before inhaling your prescribed medication. Carry out additional

measurements whenever you feel unwell or perceive shortness of breath.

• Your doctor is only interested in the highest peak flow value that you can

achieve during a measurement session. Please repeat the measurements until

you feel you have got the best possible result for the moment. Take care to

have sufficient relaxation between measurements. In case of poorer results at

each successive measurement session talk to your doctor. It may be a sign of

instable asthma.

• Please note that asthma attacks are indicated in advance by low peak

flow values before you feel it! Please contact your doctor in cases such

as these. Also do so if you have signs and symptoms such as chest

tightness, shortness of breath coughing or wheezing.

• Self-measurement means control, not diagnosis or treatment. In any

event, please be sure to discuss your measured values with your doctor.

Your doctor will also explain which values are normal for you.

• You should never alter the dosages of any medication without talking to your

doctor.

• Please note that the device stores up to 240 measured values with date and time.

When the memory is full, the oldest values are automatically erased!

Make sure you visit your doctor in time to analyse your data.

• Please confirm that date and time settings are always actual.

• The performance of the monitor can be affected by extremes of temperature

and humidity. Please refer to «technical specifications» for details.

6. Self-Assessment with the Traffic Light Scheme

The so-called «traffic light scheme» allows you to self-assess your measured

values and the course of your illness. This leads to an independent assessment of

your illness symptoms with adjustment of your medication. If you or your physician

wish to make use of this scheme, an asthma control card is enclosed with the

device, on which a green, a yellow, and a red area are marked. The area limits

should best be determined together with your physician and entered into the card.

9

Significance of the Traffic Light Scheme

Green area - OK

The lung disease is well under control. A higher medication dosage is not required.

Yellow area - Caution

Should your measured values frequently be located in this area, increase your

medication dosage as discussed with your physician.

Red area - Danger

It is dangerous if your measured values are in this area! Act as discussed with your

physician or seek emergency medical treatment.

7. Cleaning and Disinfecting

7.1. Cleaning / Disinfecting the Mouthpiece

We recommend disinfecting the mouthpiece

before your first use and at least once a week

using the following procedure:

1. Disconnect the mouthpiece from the

measuring tube and put it for at least

10 minutes into continuously boiling water.

2. Afterwards, put the mouthpiece on a fresh

paper towel and let it air dry.

3. Reassemble the mouthpiece on the

measuring tube.

• Alternatively, you can disinfect the mouthpiece by putting it into commonly

available disinfecting solutions. Please carefully follow the instructions for the

disinfecting solution! Make sure that it is suitable for a mouthpiece.

7.2. Cleaning / Disinfecting the Measuring Tube

• The performance of the monitor can be affected

by spitting or coughing into the measuring tube.

In this case please rinse the tube with distilled

water (available at a pharmacy or drugstore).

Please do not use tapwater.

PF 100 10

1. Disconnect the measuring tube from the main

unit by moving it in a forward direction.

2. Disconnect the mouthpiece from the

measuring tube.

3. Rinse the tube in distilled water, afterwards

please shake off the water and put it on a

fresh paper towel for complete drying.

• In case another user has already used

the monitor the measuring tube should be

disinfected:

1. Disconnect the tube as explained above and

put it into a commonly available disinfecting

solution. Please carefully follow the

instructions for the disinfecting solution!

2. Never put the measuring tube into boiling

water!

3. Reconnect the mouthpiece to the measuring

tube and reassemble it back to the main unit as

shown. Make sure that the tube finally

«clicks» into the fixed position.

4. Please make sure that the mea-

surement tube and the device stay

together by confirming that the

identification on tube and device is

the same.

7.3. Cleaning the Main Unit

Clean the main unit once a day with a clean,

damp cloth. Never put the main unit into

water!

11

8. Memory Handling

The 240 measuring data can be reviewed on the display:

1. Switch the monitor on and press the memory

scroll buttons.

2. By pressing the «<» button, you can see the

latest value stored in the memory with date and

time; pressing this button once at a time shows

all stored data. If you keep pressing the button

you can move quickly through the memory.

3. The «>» button works in the opposite direction.

• Memory Capacity Low

When the memory covers 230 or more

data, «MR XX» is blinks after the monitor is

switched on to indicate that the remaining

memory capacity is low.

• Memory Full

When the memory is full with 240 data,

the monitor gives a warning «beep»

when switching on and «MR 240»

is blinks. From now on, data is still

memorised but the oldest values are

automatically erased!

• Memory Clear

Please note: the memory is automatically

cleared after data transfer to computer.

Clearing all data from the memory manually should be done when you intend

to give the monitor to another person. To clear all data press the «<» and the

«>» buttons simultaneously for 5 seconds, and then release the buttons. «clr»

starts blinking in the display for about 3 seconds. If you really want to erase all

data from memory you need to press the ON/OFF button during these seconds.

Otherwise the monitor moves back to normal operation and the data remains.

• Clear the last measurement

You can erase the last memory reading by pressing both memory scroll

buttons simultaneously for 5 seconds. After releasing the buttons «clr» will

flash on the screen for 3 seconds. To erase the last reading you need to press

both buttons again while the screen is flashing.

PF 100 12

9. Analysing Data using Computer Interface

The monitor can be connected via a USB connection port with a computer and all

memory data can be analysed by the Microlife Asthma Monitor software program.

Download the free Microlife Asthma Analyser Software from www.microlife.com/

support/software

10. Messages / Malfunctions / Errors

If an error occurs one of the following listed error codes is displayed.

Message Cause Remedy

Er2 Data communication between device

and printer does not work.

Check the cable connection

between device and printer.

no There is no data stored in the Monitor.

Hi The result is higher than 900 ml/min. This is a very good result.

Other possible malfunctions

If problems occur when using the device, the following points should be checked:

Malfunction Remedy

The display remains empty. 1. Check the polarity of the batteries (+/-).

Batteries have been

installed.

2. If the display is erratic orunusual, remove the

batteries and re-install new batteries.

The instrument frequently

fails to measure or the

values measured are

wrong.

1. Ensure that the measuring tube is connected

correctly.

2. Check if when blowing into the tube, the wing wheel

is rotating. Any objects, dust liquids or mucous may

interfere the rotation of the wing wheel. In this case

clean the tube as explained.

3. Discuss the values with your doctor.

If you have any questions regarding the use of this device, please ask your dealer

or pharmacist for the Microlife Service representative in your country. The Microlife

service team will be happy to help you.

11. Battery Replacement

When the battery low symbol appears in the display, the device is blocked until the

batteries have been replaced. Please use 1.5 V «Long-Life» or «Alkaline» batteries,

size «AAA». The use of 1.2 V Accumulator batteries is NOT recommended.

If the monitor is left unused for longer periods, please remove the batteries.

Please note that during battery exchange the data stored in the memory of the

monitor is well protected and will NOT be lost.

After battery change (or when the unit has been disconnected from any

power supply) time/date needs to be entered, again! Otherwise data can not

be memorised.

13

12. Care and Safety Information

• Do not expose the device to extreme

temperatures, humidity, dust or direct sunlight.

• Clean the device with a soft, dry cloth. Do not

use gasoline, thinners or similar solvents. The

measuring tube should not be washed in a

dishwasher!

• Do not drop the instrument or treat it roughly

in any way. Avoid strong vibrations.

• Never attempt to repair the instrument

yourself. Any unauthorised opening of the

instrument invalidates all guarantee claims!

• If the device received any knocks (dropping),

you will recognise any malfunction or

damages or you receive surprising results, it

should be checked by the Microlife service

representative in your country.

• Do not use this device if you think it is damaged or

notice anything unusual.

• The function of this device may be compromised when used close to strong

electromagnetic fields such as mobile phones or radio installations and we

recommend a distance of at least 1 m. In cases where you suspect this to be

unavoidable, please verify if the device is working properly before use.

13. Guarantee

This device is covered by a 2 year guarantee from the date of purchase. During this

guarantee period, at our discretion, Microlife will repair or replace the defective

product free of charge. Opening or altering the device invalidates the guarantee.

The following items are excluded from the guarantee:

• Transport costs and risks of transport.

• Damage caused by incorrect application or non-compliance with the

instructions for use.

• Damage caused by leaking batteries.

• Damage caused by accident or misuse.

• Packaging/storage material and instructions for use.

• Regular checks and maintenance (calibration).

• Accessories and wearing parts: Batteries, mouthpiece, measuring tube.

PF 100 14

Should guarantee service be required, please contact the dealer from where the

product was purchased, or your local Microlife service. You may contact your local

Microlife service through our website: www.microlife.com/support

Compensation is limited to the value of the product. The guarantee will be granted if

the complete product is returned with the original invoice. Repair or replacement

within guarantee does not prolong or renew the guarantee period. The legal claims

and rights of consumers are not limited by this guarantee.

14. Technical Specification

Measuring range: PEF from 50 - 900 l/min

FEV1 from 0.01 - 9.99 litres

Measuring method: Rotating wing wheel

Accuracy: PEF ± 20 l/min or 10% of the reading, whichever is greater.

FEV1 ± 0.1 l or ± 5% of the reading, whichever is greater.

Measuring resolution: PEF 1 l/min; FEV1 0.01 l

Data safety: data rememorised by EEPROM

Memory: 240 measurements with date/time

Size: 77 (W) x 144 (L) x 48 (H) mm

Weight: 150g (with batteries)

Storage conditions: -5 - +50 °C / 23 - 122 °F,

10 - 90% relative maximum humidity

Operation conditions: 10 - 40 °C / 50 - 104 °F,

10 - 85% relative maximum humidity

Power source: 2 batteries of 1.5 V, size AAA

Battery lifetime: approximately 1000 measurements

IP Class: IP20

Reference to standards: CE (EU Guidelines 93/42/EEC) EN60601-1, EN60601-

1-2, EN ISO 23747, IEC60601-1-11, ATS standard

1994 update

System requirements: Microsoft® Vista, 7, 8, 550 MHz CPU,

500 MB free hard disk, 256 MB RAM, 800 x 600 pixel

re solution, 256 colour, CD-ROM drive or internet access

for online download, one free USB port

Expected service life: 5 years or 10000 measurements

Technical modifications reserved!

15. www.microlife.com

Detailed user information about our products and services can be found at

www.microlife.com

15

Moniteur d’asthme électronique

Mode d’emploi

Importantes precautions d’emploi

Partie appliquée du type BF

Les piles et appareils électroniques doivent être éliminés en conformité

avec les prescriptions locales, séparément des ordures ménagères.

Ne laissez jamais les enfants utiliser l’appareil sans surveillance. Certaines

de ses parties sont si petites qu’elles peuvent être avalées. Possible risque

d’étranglement dans le cas où l’appareil est fourni avec des câbles ou

des tuyaux.

A conserver dans un endroit sec

PF 100 16

Sommaire

1. Introduction

2. Votre moniteur d’asthme Microlife

3. Préparation pour la première mesure

3.1. Insertion des piles

3.2. Réglage de la date et de l’heure

4. Réalisation d’une mesure

5. Informations importantes pour la mesure et le contrôle de vos valeurs

6. Auto-évaluation avec le programme «Feu tricolore»

7. Nettoyage et désinfection

7.1. Nettoyage / Désinfection de l’embouchure

7.2. Nettoyage / Désinfection du tube de mesure

7.3. Nettoyage de l’unité principale

8. Mémoire

9. Analyse des données par ordinateur

10. Messages / Dysfonctionnements / Erreurs

11. Remplacement des piles

12. Entretien et informations de sécurité

13. Garantie

14. Spécifications techniques

15. www.microlife.fr

FR

17

1. Introduction

Votre nouveau moniteur Microlife est un appareil médical de haute qualité pour la

mesure de votre expiration maximum, dénommée «débit de pointe» (en termes

médicaux «DEP» - Débit expiratoire de pointe).

Surtout dans les maladies des bronches, telles que l’asthme ou la bronchite chronique,

une surveillance régulière de votre débit de pointe est très utile pour le contrôle des

troubles. Après l’indication du débit de pointe, une autre valeur (volume expiré forcé -

FEV1) s’affiche. Cette valeur est également intéressante pour votre médecin.

Vous pouvez effectuer les mesures vous-même, car le moniteur Microlife est très facile

à utiliser. Il convient aussi bien aux enfants en phase pré-scolaire qu’aux personnes

âgées.

Comme l’appareil a une mémoire automatique de jusqu’à 240 entrées, vous n’avez

pas besoin de noter les valeurs: emportez tout simplement l’appareil chez le

médecin lors de la prochaine visite. L’appareil peut être connecté à un ordinateur,

et les valeurs peuvent être analysées à l’aide du logiciel Microlife Asthma Analyser

(Analyse d’asthme Microlife).

Lisez ce manuel attentivement avant d’utiliser l’appareil et conservez-le dans un

endroit sûr.

2. Votre moniteur d’asthme Microlife

L’illustration montre le moniteur d’asthme Microlife:

3. Préparation pour la première mesure

Avant la première utilisation, nous recommandons de désinfecter l’embouchure

comme expliqué dans ce manuel.

Défilement du

contenu de la

mémoire

Compartiment

pile

Embouchure

MARCHE/ARRET

Affichage

Compartiment

données

Tube de

mesure

PF 100 18

3.1. Insertion des piles

1. Ouvrez le compartiment de pile de dessous et

insérez deux piles (1.5 V - AAA).

2. Faites attention à la polarité conformément aux

symboles dans le compartiment.

3.2. Réglage de la date et de l’heure

Le moniteur enregistre automatiquement la date et

l’heure de chaque mesure. Après l’insertion de nouvelles

piles, la date et l’heure sont réglées comme suit: année:

2005; jour 12, mois 04 et heure 00:00.

Vous devez réintroduire la date et l’heure courantes.

Pour ce faire, procédez comme suit

(exemple: 28 juin 2013, 09:50):

1. Ouvrez le compartiment données de dessous à la

position du symbole.

2. Appuyez sur le petit interrupteur d’heure à côté

de l’horloge avec un stylo et «2005» commence à

clignoter; relâchez l’interrupteur.

3. Avec les deux boutons à flèche sur l’avant du

moniteur vous pouvez réduire (bouton à flèche

gauche) ou augmenter (bouton à flèche droit) le

nombre. Relâchez le bouton à flèche lorsque vous

arrivez au nombre correct (2013).

La page charge ...

Microlife PF 100 Digital Peak Flow Asthma Monitor Manuel utilisateur

Ce manuel convient également à

Microlife PF 100 Digital Peak Flow Asthma Monitor Manuel utilisateur

dans d''autres langues

Documents connexes