Alula RE629 Guide d'installation

Marque
Alula
Modèle
RE629
Taper
Guide d'installation
The RE629 Glassbreak is a security sensor that detects
the sound of breaking glass and sends alarm signals to
the security panel.
Features
• Variable detection range of up to 20 feet
• Low battery and tamper indication
• VHB™ tape included for easy installation
Enroll by placing the panel into wireless enrollment mode
and sending an enrollment signal. Alternatively, the
sensor can be enrolled by scanning its bar code using
the Connect+ Installer App or by entering its 8-character
serial number in the AlulaConnect portal.
Select sensitivity by adjusting the dipswitch. See table
below for sensitivity settings.
Select a mounting location at a height of at least
6.5 feet (2m) and no more than 20 feet (6m) from the
window you wish to protect. Ensure the sensor has
visual line-of-sight to all windows being protected.
Use a glassbreak tester to conrm operation before
permanently mounting using the mounting screws or
VHB tape.
Test the glassbreak to verify operation after enrollment
and installation. Note, any glassbreak tester can be
used.
1. The sensor is in test mode for 5 minutes after
powered. When test mode is active, the LED will
ash once per second.
2. Activate the glassbreak tester near the window you
wish to protect.
3. If an alarm is detected, the LED will ash rapidly
for 2 seconds and an alarm signal will be sent to
the panel. If the sensor does not trip, check the
sensitivity setting or relocate the sensor and retest.
Use the panel installation guide to verify proper system setup.
RE629 Glassbreak
Connect+™ Encrypted
I
N
S
T
A
L
L
G
U
I
D
E
I
Sending an Enrollment Signal
• Remove the battery tab to power the device or
tamper the device by opening the enclosure.
SENSITIVITY DETECTION
RANGE
SWITCH 1 SWITCH 2
MAX 20FT OFF OFF
MEDIUM 13FT OFF ON
LOW 8FT ON OFF
LOWEST 5FT ON ON
Mounting Holes
Sensitivity Switches
ON
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE629
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Alula could void
the user’s authority to operate this equipment.
FCC ID: U5X-RE629
TRADEMARKS
Alula and Connect+ are trademarks owned by Alula Holdings, LLC.
3M and VHB are trademarks owned by 3M Company.
Panasonic is a registered trademark owned by Panasonic
Corporation.
Specications
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
4.1 x 2.3 x 1.0 inches (10.6 x 6.0 x 2.6 centimeters)
2.75 ounces (78 grams)
#6 screws, anchors, VHB tape (all provided)
Environmental
Operating Temperature
Maximum Humidity
32°F to 120°F (0°C to 49°C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
433.92 MHz
One Panasonic® CR123A
3.5 years
3.0 VDC (Nominal), 2.2 VDC (Low)
30 mA (Maximum), 50 uA (Quiescent)
Low Battery, Tamper, Supervision, Alarm
Certication
RE629 FCC, IC
Specications subject to change without notice.
47-00003 • REV A • 2020-04-01
Tech Support Line • (888) 88-ALULA • (888) 882-5852
alula.net
Pro Tips
3M™ VHB Tape works great if the surface is properly prepared and rm pressure is applied for
over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature is above 50 °F
When sensor detects breaking glass, the LED will turn on for 5 seconds.
  • Page 1 1
  • Page 2 2

Alula RE629 Guide d'installation

Marque
Alula
Modèle
RE629
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents