iHome iLW300 Foldable LED Lamp Mode d'emploi

Catégorie
Réveils
Taper
Mode d'emploi
*FRONT
iLW300-IS-011723-A
Printed in China
MAINTENANCE
- Place the unit on a level surface away from sources of direct sunlight or excessive heat.
- Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective
material should be placed between it and the furniture.
iLW300 - Instruction Sheet - English
Color: Black text on white paper (1C + 1C)
Size: 102 x 150 mm
Material: 85 gsm wood free paper
Jan. 17, 2023.
© 2023 SDI Technologies, Inc.
All rights reserved
Foldable LED Lamp with Wireless Charging,
USB Charging & Alarm Clock
Place device face up on the charging rest. LED Status Indicators will show charging status:
WIRELESS CHARGING
WARNING: Remove phone’s metal protective case before charging. Do not place magnetic or metal objects on
charger during charging. Qi compatible phones with metallic looking finishes will charge normally.
POWER ON/OFF
Model: iLW300
- Press to turn the lamp On and O
WIRELESS
CHARGING
TOUCH
CONTROLS
REAR
CONTROLS
CHARGING LED
BACK SIDE
BACK SIDE
POWERLIGHT PRO+
LIGHT TEMPERATURE
- Press repeately to change the light temperature in following order
• Warm light
• Cool light
• Natural light
BRIGHTNESS /
- Press to increase/decrease the brightness
DC JACK (12V/2A)
(for power supply)
USB
CHARGING
PORT
Device is not charging (reposition device)
Device is charging
Device is fully charged
Rapid blinking LED:
Slow blinking LED:
Solid LED:
LAMP ARM AND HEAD ADJUSTMENT
Note: Be sure to hold the lamp base while
adjusting the angle of the light head
BACKUP BATTERY COMPARTMENT
(for clock accuracy and alarm setting backup)
To replace the battery:
1. Make sure the AC adapter is connected, or you will lose your clock
settings during battery replacement.
2.
Use a Phillips screwdriver to unscrew the battery compartment door.
3. Remove the exhausted battery and insert a new CR2032 battery. Replace
the compartment door. Do not overtighten the screw.
Keep exhausted battery away from children and dispose of properly.
TIME SET
- In Time Mode, press the button on the back to start setting
the time
- Use / to set the hour and press button to confirm
- Use / to set the minute and press button to confirm
- Continue steps to set year, month, and date, and pres button
to confirm clock settings
Note: Use Button to set 12/24 hour display.
ALARM SET
- Press the button on the back enter the alarm set and then
press the to start setting the alarm time
- Use / to set hour and press button to confirm
- Use / to set the minute and press button to confirm
- Continue steps to set the Snooze Duration (1-60 minutes) and
alarm sound (1-8) and press button to confirm alarm settings
- Press or to arm the alarm, press again to arm the snooze
- Press or again to disarm the alarm and snooze
- Press button to back to the time display
- The alarm will sound for one minute. Press or any other
button to stop the alarm
- If snooze mode is armed, please or to snooze the alarm
TEMPERATURE
In Time Mode, Use to change the temperature display between Celsius and Fahrenheit
DISPLAY DIMMER
Press button on the back to adjust Display Brightness: cycle through Hi, Lo and OFF
Celsius/
Fahrenheit
Day
Month/
Date
AM/PM
Indicator
Time Mode
Snooze
Indicator
Alarm
Indicator
Alarm Set
Indicator
Temperature
12V 2A
5V 1A
USB
12V 2A
5V 1A
USB
TOP PANEL
MONTH DATE DAY
DISPLAY
ICONS
WARNING:
Do not ingest the battery, Chemical Burn Hazard. This product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to
death.
Keep new and used batteries away from children. If the battery compartment does not close securely, stop
using the product and keep it away from children. If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate medical attention.
CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE
INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS
Please heed all warnings, read and follow all instructions and keep these instructions handy for future reference.
1. Allow Lamp to cool before handling. Light source can become hot during operation.
2. Do not stare at the light source directly while it is in use, risk of visual impairment.
3. This product is intended for use indoors only, in dry, enclosed rooms. Never in a wet environment or with
wet hands in the vicinity of a bathtub, shower or swimming pool-Danger of Electric Shock!
2. Unplug unit and clean only with dry cloth. Stronger cleaning agents, such as Benzene, thinner or similar
materials can damage the surface of the unit.
3. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
4. Heat – This product should be situated away from heat sources such as radiators, heat registers, stoves or
other appliances (including amplifiers) that produce heat.
5. Only use attachments/accessories specified by the manufacturer.
6. Unplug this product during lightning storms or when unused for long periods of time.
7. Damage Requiring Service – This product should be serviced by qualified service personnel when:
- Plug has been damaged.
- Objects have fallen into or liquid has been spilled into the enclosure.
- The unit has been exposed to rain. The unit has been dropped or the enclosure damaged.
- The unit exhibits a marked change in performance or does not operate normally.
8. No naked flame sources, such as lighted candles, should be placed on this product.
9. This product is suitable for use in tropical and/or moderate climates.
WARNING:
- To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
- Do not dispose of batteries in the household trash or fire.
- The mains plug of power adaptor is used as the disconnect device, it shall remain readily operable.
FCC Information
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with minimum distance 20cm (8 inches) between the radiator & your body.
ISED Information
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The device comply with ISED RF exposure requirement, users can obtain Canadian information on RF exposure and
compliance.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
Cet équipement est aux limites d'exposition aux radiations IC CNR-102 établies pour un environnement non contrôlé.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
L'appareil est conforme aux exigences d'exposition RF ISED, les utilisateurs peuvent obtenir des informations canadiennes
sur l'exposition aux RF et la conformité.
Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
Tout changement ou modification non expressément approuvé par la partie responsable de la conformité peut annuler
l'autorité de l'utilisateur à utiliser l'équipement.
CAN ICES-3 (B) / NMB-3(B), CAN RSS-216 / CNR-216
  • Page 1 1

iHome iLW300 Foldable LED Lamp Mode d'emploi

Catégorie
Réveils
Taper
Mode d'emploi

dans d''autres langues