Simplicity SNOWTHROWER, DUAL STAGE SEARS CRAFTSMAN 8.0/24 (C950-52410-0) Manuel utilisateur

Not for

Reproduction

Operator’s Manual

Dual Stage Snowthrower

Model No. C950-52410-0 (1696556-00)

CAUTION: Before using this product, read the manual and

follow all its Safety Messages and Operating Instructions.

Sears Canada Inc., Toronto, Ontario M5B 2C3

Visit our Craftsman website: www.sears.ca/craftsman

80010845

Revision A

Not for

Reproduction

2

Manual Contents

Thank You Statement ........................................................2

ID Tag and Location ...........................................................2

Operator Safety ..................................................................3

Safety Decals ......................................................................8

Safety System Tests ..........................................................9

Features and Controls .................................................... 10

Operation ......................................................................... 12

Maintenance .................................................................... 17

Troubleshooting .............................................................. 22

Specifications .................................................................. 23

Warranty ........................................................................... 24

The images in this document are representative, and are

meant to complement the instructional copy they accompany.

Your unit may vary from the images displayed. LEFT and

RIGHT are as seen from the operator’s position.

Thank you for purchasing this quality-built CRAFTSMAN®

Snowthrower. We’re pleased that you’ve placed your con-

dence in the CRAFTSMAN brand. When operated and main-

tained according to the manuals, your CRAFTSMAN product

will provide many years of dependable service.

The manuals contain safety information to make you aware

of the hazards and risks associated with the unit and how to

avoid them. This Snowthrower was designed to be used as

described in operator’s manual and is not intended for any

other purpose. It is important that you read and understand

the instructions thoroughly before attempting to start or oper-

ate this equipment. Save these original instructions for

future reference.

This product requires nal assembly before use. Refer to the

setup guide for instructions on nal assembly procedures.

Follow the instructions completely.

Product Model Number:

Product Serial Number:

Engine Model-Type Number:

Engine Code/Serial Number:

Date of Purchase:

Purchase Location:

When contacting your authorized dealer for replacement

parts, service, or information you MUST have these

numbers.

Record your model name/number, manufacturer’s

identification numbers, and engine serial numbers in the

space provided for easy access. These numbers can be

found in the locations shown.

USA

XXXXX

For Parts and Service Call

Pour des pices et l’intervention

SEARS CANADA INC.

Toronto, Ontario M5B2C3

MODEL / MODÈLE

SERIAL NO. / NO. SÉRIE

Assembled In

Rassemblé dans

PRODUCT IDENTIFICATION /

IDENTIFICATION DE PRODUIT

XXXXXXXXXXXXXXXXXXXX

XXXXXXX - XX

XXXXXXXXX

XXX-XXX-XXXX

WWW.XXXXXX.COM

X X X X X X X X X X X X

THANK YOU STATEMENT

ID TAG AND LOCATION

Not for

Reproduction

3

English

en

The product identification tag (A) can be found in the

location shown in Figure 1.

1

Hazard Symbols and Meanings

Read the Operator’s Manual

Remove key before performing

maintenance

Carbon monoxide poisoning hazard

Fire hazard

Explosion hazard

Kickback hazard

Hot surface hazard

Wear safety glasses

Thrown objects hazard

Amputation hazard - rotating impeller

Amputation hazard - rotating auger

OPERATOR SAFETY

Safety Alert Symbol and Signal Words

The safety alert symbol is used to identify safety information

about hazards that can result in personal injury. A signal word

(DANGER, WARNING, or CAUTION) is used with the alert symbol

to indicate the likelihood and potential severity of injury. In

addition, a hazard symbol may be used to represent the type of

hazard.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates an action that could result in damage to

the product.

Not for

Reproduction

4

Entanglement hazard - rotating parts

Electric shock hazard

Keep safe distance away

Keep children away

WARNING

• Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with

snowthrowers.

• This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so could result in

death or serious injury.

WARNING

• Save these original instructions for future reference.

• Be thoroughly familiar with the controls and the proper use

of the snowthrower.

• Make sure you are properly trained before operating the

snowthrower.

• Know how to stop the unit and disengage the controls

quickly.

• Never allow anyone to operate the snowthrower without

proper instruction.

• Always follow the instructions in the operator’s manual, if

the snowthrower will be stored for an extende d period.

• Maintain or replace safety and instruction labels as

necessary.

• Never attempt to make major repairs on the snowthrower

unless you have been properly trained. Improper servicing

of the snowthrower can result in hazardous operation,

equipment damage, and voiding of the product warranty.

Read, understand, and follow all the

instructions on the snowthrower and in the

operator’s manual before operating this unit.

Failure to observe the safet y instructions in this

manual could result in death or serious injury.

Discharge chute contains rotating impeller

to throw snow. Never clear or unclog the

discharge chute with your hands. Fingers can

quickly become caught in the impeller. Always

use a clean-out tool.

Failure to observe these safety instructions

will result in traumatic amputation or severe

laceration.

DANGER

• Whenever cleaning, repairing, or inspecting the

snowthrower, make sure the engine is OFF, spark plug wire

is disconnected, and all moving parts have stopped.

• Do not put hands or feet near or under rotating parts. Keep

clear of the discharge opening at all times.

• Never operate the snowthrower without proper guards, and

other safety devices in place and working.

• Never leave the snowthrower unattended while engine is

running. Always disengage the auger and traction controls,

stop engine, and remove keys.

• Keep all loose clothing away from the front of the

snowthrower and auger. Scarves, mittens, dangling

drawstrings, loose clothes, and pants can quickly become

caught in the rotating device and amputation will occur. Tie

up long hair and remove jewelry.

• Run the machine a few minutes after discharging snow to

prevent freeze-up of the collector/impeller.

• Disengage power to the collector/impeller when

snowthrower is transported or not in use.

Keep hands, feet, and clothing away from

rotating parts. Rotating parts can contact

or entangle hands, feet, hair, clothing, or

accessories.

Failure to observe these safety instructions

will result in traumatic amputation or severe

laceration.

Not for

Reproduction

5

English

en

WARNING

• Always wear safety glasses or eye shields during

operation, and while performing an adjustment or repair.

• Always be aware of the direction the snow is being

thrown. Nearby pedestrians, pets, or property may be

harmed by objects being thrown.

• Be aware of your environment while operating the

snowthrower. Don’t run over items such as gravel,

doormats, newspapers, toys, and rocks hidden under

snow, as they can all be thrown from the chute or jam in

the auger.

• Use extreme caution when operating on or crossing

gravel drives, walks, or roads.

• Adjust the collector housing height to clear gravel or

crushed rock surface.

• Never operate the snowthrower near glass enclosures,

automobiles, window wells, drop-offs, and the like without

proper adjustment of the discharge chute angle.

• Familiarize yourself with the area in which you plan

to operate the snowthrower. Mark off boundaries of

walkways and driveways.

Objects can be picked up by auger and thrown

from chute. Never discharge snow toward

bystanders or allow anyone in front of the

snowthrower. Failure to observe these safety

instructions will result in death or serious injury.

WARNING

• Keep children out of the area during operation. Children are

often attracted to the equipment. Be mindful of all persons

present.

• Be alert and turn unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision. Children

may be present.

Tragic accidents can occur if the operator is

not alert to the presence of children. Children

are often attracted to the unit and the operating

activity. Never assume the children will remain

where you last saw them.

Engines give off carbon monoxide, an

odorless, colorless, poison gas. Breathing

carbon monoxide can cause nausea, fainting,

or death.

WARNING

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors or

windows are open.

WARNING

When Adding Fuel

• Turn off engine and let cool at least 2 minutes before

removing the fuel cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion of

gasoline, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat,

and other ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks or

leaks. Replace if necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting engine.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air cleaner (if

equipped) are in place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but move

the snowthrower away from the area of the spill, and avoid

creating any source of ignition, until the fuel vapors have

dissipated.

• Do not over-prime the engine. Follow the engine starting

instructions in this manual.

• If the engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position and

crank until engine starts.

Fuel and its vapors are extremely flammable

and explosive. Always handle fuel with

extreme care.

Failure to observe these safety instructions can

cause a fire or explosion which will result in

severe burns or death.

Not for

Reproduction

6

When Operating Equipment

• Do not tip the snowthrower at an angle which causes the

fuel to spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if

equipped) or the air filter (if equipped) removed.

When Changing Oil

• If you drain the oil from the top oil fill tube, the fuel tank

must be empty or fuel can leak out and result in a fire or

explosion.

When Transporting Equipment

• Transport with fuel tank EMPTY, or with fuel shut-off valve

OFF.

When Storing Gasoline or Equipment With Fuel in Tank

• Store away from furnaces, stoves, water heaters, or other

appliances that have pilot light or other ignition source

because they can ignite fuel vapors.

WARNING

• Disengage all clutches and shift into neutral before starting

the engine.

• Let the engine adjust to outdoor temperatures before

starting to clear snow.

• Use a grounded three-wire plug for all snowthrowers

equipped with electric drive motors or electric starting

motors.

WARNING

• If there is natural or LP gas leakage in area, do not start

engine.

• Do not use pressurized starting fluids because vapors are

flammable.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

Running the engine produces heat. Engine

parts, especially muffler, become extremely

hot.

Failure to observe these safety instructions

could result in severe thermal burns on contact.

Safe operation of the snowthrower requires

the proper care and maintenance of the

engine.

• Never touch a hot engine or muffler. Allow muffler,

engine cylinder, and fins to cool before touching.

• Remove debris from muffler area and cylinder area.

• Install and maintain in working order a spark arrester

before using equipment on forest-covered, grass-

covered, or brush-covered unimproved land.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any

forest-covered, brush-covered, or grass-covered

land unless the exhaust system is equipped with a

spark arrester, as defined in Section 4442, maintained

in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original

equipment manufacturer, retailer, or dealer to obtain a

spark arrester designed for the exhaust system installed

on this engine.

WARNING

• When performing any maintenance or repairs on the

snowthrower, shut OFF the engine, disconnect spark plug

wire, and keep the wire away from the plug to prevent

someone from accidently starting the engine.

• Check shear bolts and other hardware at frequent intervals

for proper tightness.

• Keep nuts and bolts tight and keep snowthrower in good

condition.

• Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if they are

not functioning properly.

• Components are subject to wear, damage, and deterioration.

Frequently check components and replace with

recommended parts, when necessary.

• Check control operation frequently. Adjust and service as

required.

• Use only factory authorized replacement parts, or like, parts

when making repairs.

• Always comply with factory specifications on all settings and

adjustments.

• Use only factory authorized, or like, attachments and

accessories such as wheel weights, counterweights, or cabs.

• Never attempt to make any adjustments while the engine

is running (except when specifically recommended by the

factory).

This snowthrower must be properly

maintained to ensure safe operation and

performance. Failure to observe the safety

instructions in this manual could result in

death or serious injury.

Not for

Reproduction

7

English

en

WARNING

This snowthrower is only as safe as the opera-

tor. If it is misused, or not properly maintained,

it can be dangerous. Remember you are re-

sponsible for your safety and those around you.

• Keep the area of operation clear of all persons, particularly

small children and pets.

• Thoroughly inspect the area where the snowthrower will be

used and remove all doormats, sleds, boards, wires, and

other foreign objects.

• Do not operate the snowthrower without wearing adequate

winter clothing.

• Wear footwear that will improve footing on slippery surfaces.

• Use caution to avoid slipping or falling especially when

operating the snowthrower in reverse.

• Never operate the snowthrower without good visibility or

light. Always be sure of your footing, and keep a firm hold on

the handles.

• Do not clear snow across the face of slopes. Use extreme

caution when changing direction on slopes. Do not attempt

to clear steep slopes.

• Do not overload the machine capacity by attempting to clear

snow too quickly.

• Never operate the snowthrower at high transport speeds on

slippery surfaces. Look behind the snowthrower and use

care when operating in reverse.

• Do not use the snowthrower on surfaces above ground level

such as roofs of residences, garages, porches, or other such

structures or buildings.

• Operators should evaluate their ability to operate the

snowthrower safely enough to protect themselves and

others from injury.

• The snowthrower is intended to remove snow only. Do not

use the snowthrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine,

disconnect the cord on electric motors, thoroughly inspect

the snowthrower for any damage, and repair the damage

before restarting and operating the snowthrower.

• If the snowthrower vibrates abnormally, shut OFF the

engine. Vibration is generally a warning of trouble. See an

authorized dealer if necessary for repairs.

• For models equipped with electric starting motors,

disconnect the power cord after the engine starts.

WARNING

Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine

faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

When Starting the Engine

• Pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

WARNING

Damaged or ungrounded power cords could

cause electric shock.

Electric shock could cause severe burns or

death.

When Using the Electric Starter

• The power cord must be properly grounded at all times.

• Use only a three-conductor power cord properly grounded

to the power source.

• If the extension cord is damaged, it must be replaced a

qualied person to avoid a hazard.

Not for

Reproduction

8

Before operating your unit, read the safety decals. Compare

Figure 2 with the table below. The cautions and warnings are

for your safety. To avoid a personal injury or damage to the

unit, understand and follow all the safety decals.

WARNING

If any safety decals become worn or damaged, and

cannot be read, order replacement decals from your

local dealer.

A

Chute Danger

Decal

(P/N 1737865)

B

Auger Danger

Decal (small-

frame models)

(P/N 1752919

- Warning;

1752422 -

Danger)

DANGER

WARNING

AVERTISSEMENT

2

A

B

SAFETY DECALS

Not for

Reproduction

9

English

en

SAFETY SYSTEM TESTS

DANGER

Amputation hazard

This snowthrower is equipped with several mechanical

safety systems designed to keep the operator safe while

using the unit. Check the operation of these systems regu-

larly using the safety system tests listed. If the unit fails to

operate as described, DO NOT operate it. See your autho-

rized dealer for service immediately.

Test 1 - Auger/Impeller Control

With the engine running:

• Press down on the auger control lever. (The auger/impel-

ler should rotate)

• Release the auger control lever. (The auger/impeller

must stop within 5 seconds)

Test 2 - Traction Drive Control

With the engine running and speed control in 1st gear:

• Press down on the traction control lever. (The unit should

move forward)

• Release the traction control lever. (The unit must stop)

Not for

Reproduction

10

Snowthrower

Compare Figure 3 with the table below.

A

B

D

F

G

H

I

C

E

3

A

Auger Control Lever - Used to

engage and disengage the auger

and impeller. To engage, push

down. To disengage, release.

B

1

R1

R2

2

3

Speed Select Lever - Allows

the operator to use one of six

forward and two reverse speeds.

To shift, move speed select lever

to desired position.

NOTICE: Do not move speed

select lever while Traction

Control is engaged. This may

result in severe damage to the

drive system.

C

Chute Rotation Crank -

Lefthand Crank - Used to rotate

the discharge chute to the left or

right.

D

Traction Control Lever - Used

to propel snowthrower forward or

reverse. Push down to engage,

release to disengage. See also,

“Free-Hand Control”.

E

Deflector Control - Manual -

Used to control the angle of the

deflector (up or down).

F

Grip Warmer Switch - Used to

operate the heated hand grips.

The switch has three positions -

High, Off, and Low.

G

-

Clean-Out Tool - Used to

remove snow and debris from

the discharge chute and the

auger housing.

H

-

Skid Shoes - Used to adjust the

ground clearance of the auger

housing.

I

-

Headlight - Illuminates the area

in front of the snowthrower.

NOTE: Headlight design varies

according to model.

FEATURES AND CONTROLS

Not for

Reproduction

11

English

en

Engine

A. Choke Control Knob — Used to start a cold engine

(see Figure 4).

B. Electric Start Button — Used to start the engine using

the electric starter.

C. Primer Button — Used to inject fuel directly into the

carburetor manifold to ensure fast starts in cool

weather.

D. Safety Key — Must be inserted to start engine. Pull out

to stop. Do not turn safety key.

E. Starter Cord Handle — Used to start the engine

manually.

F. Fuel Tank and Cap — Fill the fuel tank to

approximately 1-1/2 in. (38 mm) below the top of

the neck to allow for fuel expansion.

G. Oil Fill Cap (Extended Dipstick)

C

G

A

E

F

STOP

D

B

4

Not for

Reproduction

12

Operating the Snowthrower

DANGER

Amputation hazard

The discharge chute contains a rotating impeller to

throw snow. Fingers can quickly become caught in

the impeller. Never clear or unclog the discharge

chute with your hands. Always use a clean-out tool.

Failure to observe these safety instructions will result

in traumatic amputation or severe laceration.

Hand contact with the rotating impeller inside the dis-

charge chute is the most common cause of injury associ-

ated with snowthrowers. Never use your hands to clean out

the discharge chute.

Before Operating the Snowthrower

WARNING

Read the operator’s manual before operating the

machine. This machine can be dangerous if used

carelessly.

• Never operate the snowthrower without all guards,

covers, and shields in place.

• Stop the engine whenever leaving the operating posi-

tion.

• Remove the key before unclogging the impeller hous-

ing or discharge chute, and before making repairs or

adjustments.

• When leaving the machine, remove the key.

• To reduce the risk of fire, keep the machine clean and

free from spilled fuel, oil, and debris.

• On electric start models, disconnect the extension

cord before operating.

• Be sure to check the engine oil level before starting

the engine. See the engine operator’s manual for oil

recommendations.

OPERATION

DANGER

Toxic fume hazard

Engines give off carbon monoxide, an odorless, col-

orless, poison gas.

Breathing carbon monoxide can cause nausea, faint-

ing, or death.

• Start and run the engine outdoors.

• Do not run the engine in an enclosed area, even if

doors and windows are open.

WARNING

Thrown objects hazard

This machine is capable of throwing objects that could

injure bystanders, or cause damage to buildings.

Be sure the operating area is clear of bystanders. Never

direct the discharge toward anyone, or toward buildings or

cars.

1. Start the engine.

2. Rotate the chute rotation crank (C, Figure 3) to set the

direction of the discharge chute.

3. Loosen the wingnut securing the chute deflector (E).

Raise the deflector to throw snow further. Set the defec-

tor to the desired position and tighten the wingnut.

4. Use the speed select lever (B) to select the forward or

reverse drive speed. Use lower speeds when clearing

wet, heavy snow. Use higher speeds for light snow or

transporting.

NOTE: Always set engine speed to FAST (full throttle).

5. Fully press the auger control lever (A) to engage the

auger. Release the lever to stop the auger.

6. Fully press and hold the traction control lever (D)

to engage the traction drive and begin moving the

snowthrower. To stop, release the lever.

NOTE: Always release the traction control lever before

changing speeds.

To safely clear a clogged discharge chute, follow these

instructions:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have

stopped rotating.

3. Always use a clean-out tool, not your hands.

Not for

Reproduction

13

English

en

Stop the Snowthrower

1. Release the traction control lever (D, Figure 3).

2. Pull out the safety key (D, Figure 4).

3. Keep the safety key out of the reach of children.

Check the Oil

NOTE: The engine was shipped from the factory lled with oil.

Check the level of the oil. Add oil as needed.

1. Make sure the unit is level. Use a high quality detergent oil

classified “For Service SF, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick (A, Figure 5) and wipe with a

clean cloth.

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the engine runs.

5. If necessary, add oil until the oil reaches the FULL mark

on the oil fill cap/dipstick (B). Do not add too much oil.

6. Tighten the oil fill cap/dipstick securely each time you check

the oil level.

NOTE: For extreme cold operating conditions of 0°F (-18°C)

and below, use a synthetic 5W30 motor oil for easier starting.

NOTE: S.A.E. 5W30 motor oil may be used to make

starting easier in areas where the temperature is 20°F

(-7°C) to 0°F (-18°C). Synthetic 5W30 is acceptable for all

temperatures. DO NOT mix oil with gasoline. See Chart for oil

recommendations.

A

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil con-

sumption. Check oil level more frequently.

5

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. For

carbureted engines, high altitude adjustment is required

to remain emissions compliant. Operation without this

adjustment will cause decreased performance, increased fuel

consumption, and increased emissions. Contact a Briggs &

Stratton Authorized Service Dealer for high altitude adjustment

information.

Operation of the engine at altitudes below 2,500 feet (762

meters) with the high altitude adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude

adjustment is necessary.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane / 87 AKI (91 RON). For high

altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

NOTICE: Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will cause

damage to engine components, which will not be covered

under warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See Storage. All fuel is not the

same. If starting or performance problems occur, change

fuel providers or change brands. This engine is certified to

operate on gasoline. The emissions control system for this

engine is EM (Engine Modifications).

Not for

Reproduction

14

Start the Engine

Be sure that engine oil is at FULL mark on the oil ll cap/dipstick.

The snowthrower engine is equipped with an A.C. electric starter

and recoil starter. Before starting the engine, be certain that you

have read the following information.

If engine oods, set the choke to the OPEN/RUN position and crank

until the engine starts.

WARNING: Rapid retraction of the starter cord

(kickback) will pull your hand and arm toward the

engine faster than you can let go. Broken bones,

fractures, bruises, or sprains could result. When starting

engine, pull the starter cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

NOTE: If the engine does not start after three attempts, see

an authorized dealer.

A

B

C

A

6. Rewind Start: Firmly hold the starter cord handle (A, Figure 7).

Pull the starter cord handle slowly until resistance is felt, then pull

rapidly.

WARNING: The electric starter is equipped with a

three−wire power cord and plug designed to operate on AC

house hold current. The power cord must be properly

grounded at all times to avoid the possibility of electric shock

which can cause injury to the operator. Follow all instructions

carefully as set forth:

Make sure your house has a three−wire grounded system.

If you are not sure, ask a licensed electrician. If your house

does not have a three−wire grounded system, do not use

this electric starter under any condition.

If your house has a three−wire grounded system but a

three-hole receptacle is not available to connect the electric

starter, have a three−hole receptacle installed by a licensed

electrician.

WARNING: To connect power cord, always

connect the power cord rst to the switch box

located on the engine and then plug the other end into a

three−hole grounded receptacle.

WARNING: To disconnect the power cord,

always unplug the end connected to the three−

hole grounded receptacle rst.

1. Check the oil level. See Check the Oil section.

2. Make sure equipment drive controls are disengaged.

3. Insert the safety key (A, Figure 6) into the safety key slot

and push fully in to the RUN position.

4. Turn the choke control knob (B) to the CHOKE position.

NOTE: Do not use the choke to start a warm engine.

5. Push the primer button (C) two times.

NOTE: Do not use the primer to start a warm engine.

NOTE: Make sure the electric extension cord is removed from

the power receptacle.

Adding Fuel

WARNING

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

When Adding Fuel

• Turn engine off and let engine cool at least 2 minutes

before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the fuel,

do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting engine.

7

6

Not for

Reproduction

15

English

en

Wheels equipped with a traction lock pin (A, Figure 8) can be

completely released by removing the pin and installing it in

the outer axle hole. Reverse this process to engage the drive

wheel.

Wheel Release - Lock Pins

8

A clean-out tool (A, Figure 9) is provided with the unit.

Clearing a Clogged Discharge Chute

DANGER

Amputation hazard

The discharge chute contains a rotating impeller to

throw snow. Fingers can quickly become caught in

the impeller. Never clear or unclog the discharge

chute with your hands. Always use a clean-out tool.

Failure to observe these safety instructions will result

in traumatic amputation or severe laceration.

Hand contact with the rotating impeller inside the dis-

charge chute is the most common cause of injury associ-

ated with snowthrowers. Never use your hands to clean out

the discharge chute.

9

To safely clear a clogged discharge chute, follow

these instructions:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have

stopped rotating.

3. Always use a clean-out tool, not your hands.

1. Pull out the safety key (D, Figure 4).

2. Keep the safety key out of the reach of children.

Stop the Engine

WARNING

Gasoline and vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop the engine.

Not for

Reproduction

16

10

When removing snow from a hard surface area such as a

paved driveway or walk, adjust the skids up to bring the front

of the snowthrower down.

When removing snow from gravel-covered or uneven sur-

faces, raise the front of the snowthrower by moving the skids

down. This will help to prevent rocks and other debris from

being picked up and thrown by the augers.

1. Determine how much clearance you want between the

scraper bar at the bottom of the auger housing and the

ground. If clearing a gravel surface, enough ground clear-

ance is needed to prevent the unit from picking up rocks.

2. Place a block equal to the desired ground clearance

under the scraper bar.

3. Loosen the skid shoe mounting nuts (A, Figure 10) and

push the skid shoe (B) down until it touches the ground.

Re-tighten mounting nuts.

4. Set the skid shoe on the other side at the same height.

Skid Shoe Height Adjustment

DANGER

Amputation hazard

The discharge chute contains a rotating impeller to throw

snow. Fingers can quickly become caught and traumatic

amputation or severe laceration will result. Hand contact

with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snowthrow-

ers.

Turn the engine OFF, wait for all moving parts to stop, and

remove the engine key before performing any maintenance

or repairs.

WARNING

Thrown objects hazard

Objects such as gravel, rocks, or other debris, if struck

by the impeller, may be thrown with sufficient force to

cause personal injury, property damage, or damage to the

snowthrower.

Be sure to set the skid shoes at the proper height to main-

tain ground clearance for the type of surface being cleared.

This snowthrower is equipped with two height adjust skids,

secured to the outside of the auger housing. These elevate

the front of the snowthrower.

Not for

Reproduction

17

English

en

Engine Maintenance

Check Crankcase Oil Level - Before starting engine and after

each 8 hours of continuous use. Add the recommended motor

oil as required.

NOTE: Over lling the engine can aect performance. Tighten

the oil ll cap securely to prevent leakage.

Change Oil - Every 50 hours of operation or at least once a

year, even if the snowthrower is not used for fifty hours. Use

a clean, high quality detergent oil. Fill the crankcase to FULL

line on dipstick (A, Figure 11). Be sure original container is

marked: A.P.I. service “SF” or higher. Do not use SAE10W40

oil (as it may not provide proper lubrication). See Chart for oil

recommendations.

Maintenance Chart

SNOWTHROWER

After Each Use

Remove the snow and slush o snowthrower to prevent

freezing of controls

Every 8 Hours or Daily

Perform snowthrower safety tests

Every 25 Hours or Annually *

Check tire pressure

Check snowthrower for loose hardware

See Dealer Annually to

Lubricate control levers and linkages

Lubricate deector hinge

Lubricate deector motor (if equipped)

Lubricate chute rotation gear (if equipped)

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 50 Hours or Annually *

Change engine oil

Check muer and muer guard.

See Dealer Annually to

Replace spark plug

Check valve clearance

* Not required unless there are problems with engine

performance.

Emissions Control Statement

Maintenance, replacement, or repair of the emissions control

devices and systems may be performed by any non-road

engine repair establishment or individual. However, to obtain

“no charge” emissions control service, the work must be per-

formed by a factory authorized dealer. See the Emissions

Warranty.

MAINTENANCE

Full

A

11

Drain Oil – Position snowthrower so that the oil drain plug is

lowest point on engine. When the engine is warm, remove oil

drain plug and oil fill cap and drain oil into a suitable container.

Replace oil drain plug and tighten securely. Refill crankcase

with the recommended motor oil.

Not for

Reproduction

18

13

Using a grease gun, lubricate the auger shaft fittings (B,

Figure 13). Refer to the Maintenance Schedule. Each time a

shear bolt or pin (C) is replaced, the auger shaft MUST be

greased.

For storage or when replacing shear bolts or pins, remove

the shear bolts or pins (C), lubricate the shaft fittings (B),

and rotate the augers several times to distribute the grease.

Reinstall the shear bolts or pins when complete.

NOTE: Some models are not equipped with grease fittings

and are exempt from these requirements.

Lubricate Auger Shaft Fittings

12

The auger gear box is lubricated at the factory and should

not require additional lubrication. However, if lubricant has

leaked out or the auger gear box has been serviced, addi-

tional lubricant may be required.

To check the auger gear box grease level, remove the filler

plug (A, Figure 13). Using a piece of wire as a dipstick, check

to confirm the presence of grease in the gearbox. If grease is

visible, do not add. If grease is not visible, add the required

lubricant. Use the color of the remaining grease to determine

what type of lubricant to add. If the grease is white in color,

add Lubriplate GR132 Grease or equivalent. If the grease is

brown in color, add EP1 lithium grease. Gearbox lubricant

capacity is 3-1/4 ounces (92 grams).

NOTE: Some auger gear boxes do not have a filler plug.

Please see your dealer for maintenance.

Lubricate Auger Gear Box

Auger Assembly Lubrication

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil con-

sumption. Check oil level more frequently.

Lubricate the unit at the locations show in Figure 12. Where

an oil can is pictured, lubricate with engine oil. Where a

grease gun is pictured, lubricate with lithium grease.

Control Lever Linkage Lubrication

WARNING

Amputation hazard

It is critical for safe operation of the unit that the controls

disengage when released. Under no circumstances should

the unit be used if the controls do not function properly.

See Safety Systems Tests to confirm correct operation.

Not for

Reproduction

19

English

en

Lubricate the chute rotation gear (Figure 14) with grease, and

the deflector mechanism with automotive type oil. Refer to

the Maintenance Schedule.

Where an oil can is pictured, lubricate with engine oil. Where

a grease gun is pictured, lubricate with lithium grease.

Discharge Chute and Deflector Lubrication

14

NOTICE

Do not allow grease or oil to contact the rubber friction wheel

or the disc drive plate. If the disc drive plate or friction wheel

come in contact with grease or oil damage to rubber friction

wheel will result.

If grease or oil comes into contact with the disc drive plate or

friction wheel, make sure to clean plate and wheel thoroughly

with an alcohol based solvent.

1. Position speed select lever in the first forward gear.

2. Drain fuel to an approved container.

Hex Shaft and Chain Lubrication

3. Stand the snowthrower up on the auger housing end.

NOTE: When the crankcase is filled with oil, do not leave

the snowthrower standing up on the auger housing for an

extended period of time.

4. Remove the bottom panel.

5. Lubricate the chains (A, Figure 15) with grease.

6. Wipe the hex shaft (B) with 5W30 synthetic motor oil,

before storage and at the beginning of each season.

7. Install the bottom panel.

WARNING

Fire and explosion hazard

Gasoline is highly flammable and its vapors are explosive.

Drain gasoline outdoors, away from fire and other ignition

sources. Wipe up any spills immediately. Do NOT allow

open flame, smoking, or matches in the area.

The gear drive system requires no maintenance or adjust-

ment. Should you have a problem with the gear drive system,

contact your authorized service dealer.

Gear Drive System

Tire pressure should be checked periodically. Recommended

tire pressure varies by tire manufacturer. A good rule of

thumb is to inflate the tire up to, but not exceeding, the “Max

Inflation” stamped on the side-wall of the tire.

Checking Tire Pressure

15

Not for

Reproduction

20

The traction drive belt is under constant spring tension and

does not require any adjustment. If the traction drive belt is

slipping, see your authorized dealer.

If the speed control rod requires adjustment, see an autho-

rized dealer.

Traction Drive Belt Adjustment

Speed Control Rod Adjustment

16

WARNING

Amputation hazard

The discharge chute contains a rotating impeller to throw

snow. Fingers can quickly become caught and traumatic

amputation or severe laceration will result. Hand contact

with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snowthrow-

ers.

Turn the engine OFF, wait for all moving parts to stop, and

remove the engine key before performing any maintenance

or repairs.

1. With the auger control lever released, the hook (A, Figure

16) should barely touch the lever (B) without raising it.

There can be a maximum of 1/32” (0.8 mm) clearance.

2. To adjust, loosen the nut (C) by holding the adjusting

flats (D) and turning the nut. Then, turn the adjusting

flats and hold the adjustment screw (E). The adjustment

screw is a phillips screw and the head can be held or

turned by inserting a screwdriver through the spring (F).

3. Hold the adjusting flats and tighten the nut.

4. To ensure that the auger does not engage unless the

control is fully depressed, please perform the Safety

System Tests. The auger must stop within 5 seconds

of the control being released.

Auger Cable Adjustment

WARNING

Amputation hazard

Over-tightening the auger cable may cause the auger drive

to engage without depressing the auger drive control.

Follow the adjustment procedure to ensure the cable is not

over-tightened.

The cables are adjusted at the factory and no adjustment

should be necessary. However, if the cables have become

stretched or are sagging, adjustment will be necessary.

Please see your dealer for this adjustment.

Traction Cable Inspection

Shear Bolt Replacement

1. Turn off the engine and wait for all moving parts to stop.

2. Remove the existing shear bolt.

3. Spin the auger to lubricate the auger shaft.

4. Align the bolt holes. Install the new shear bolt (A, Figure

17) through the auger shaft (B). Secure with the locknut

(C).

17

La page charge ...

Simplicity SNOWTHROWER, DUAL STAGE SEARS CRAFTSMAN 8.0/24 (C950-52410-0) Manuel utilisateur

Ce manuel convient également à

Simplicity SNOWTHROWER, DUAL STAGE SEARS CRAFTSMAN 8.0/24 (C950-52410-0) Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents