Horizon Fitness T303-2 Le manuel du propriétaire

Marque: Horizon Fitness

Modèle: T303-2

Catégorie: Fitness, gymnastique

Taper: Le manuel du propriétaire

TREADMILL OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE DU TAPIS ROULANT

MANUAL DEL PROPIETARIO DE LA CAMINADORA

Read the TREADMILL GUIDE before using this OWNER’S MANUAL.

Lire le GUIDE D’UTILISATION DU TAPIS ROULANT avant de se référer au présent MANUEL DU PROPRIÉTAIRE.

Lea la GUÍA DE LA CAMINADORA antes de utilizar este MANUAL DEL PROPIETARIO.

T303

3 ENGLISH

34 FRANÇAIS

66 ESPAÑOL

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an electrical product, basic precautions should always be followed, including the following: Read all instructions

before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately

informed of all warnings and precautions. If you have any questions after reading this guide, contact Customer Tech

Support at the number listed on the back panel of the OWNER’S MANUAL.

This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional

setting. Failure to comply will void the warranty.

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• Never use the treadmill before securing the safety tether clip to your clothing.

• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop

exercising immediately and consult your physician before continuing.

• When exercising, always maintain a comfortable pace.

• Do not wear clothes that might catch on any part of the treadmill.

• Always wear athletic shoes while using this equipment.

• Do not jump on the treadmill.

• At no time should more than one person be on treadmill while in operation.

• This treadmill should not be used by persons weighing more than specified in the OWNER’S MANUAL WARRANTY

SECTION. Failure to comply will void the warranty.

• When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck.

• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly

damp cloth only; never use solvents. (See MAINTENANCE)

• The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting

on or taking off parts.

• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

• Connect this exercise product to a properly grounded outlet only.

WARNING

TO REDUCE THE RISK OF ELECTRICAL SHOCK:

Always unplug the treadmill from the electrical outlet immediately after using, before cleaning, performing maintenance and putting

on or taking off parts.

DANGER

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:

• At NO time should pets or children under the age of 13 be closer to the treadmill than 10 feet.

• At NO time should children under the age of 13 use the treadmill.

• Children over the age of 13 or disabled persons should not use the treadmill without adult supervision.

• Use the treadmill only for its intended use as described in the treadmill guide and owner’s manual.

• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.

• Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped or

damaged, or immersed in water. Return the treadmill to a service center for examination and repair.

• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.

• Never operate the treadmill with the air opening blocked. Keep the air opening clean, free of lint, hair, and the like.

• To prevent electrical shock, never drop or insert any object into any opening.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

• Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool

rooms, bathrooms, car ports or outdoors. Failure to comply will void the warranty.

• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional

setting. Failure to comply will void the warranty.

• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an

authorized service technician.

It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed

to colder temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room

temperature before first time use. Failure to do so may cause premature electronic failure.

WARNING

GROUNDING INSTRUCTIONS

This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least resistance

for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed

and grounded in accordance with local codes and ordinances.

Connect this exercise product to a properly grounded outlet only.

Never operate product with a damaged cord or plug even if it is working

properly. Never operate any product if it appears damaged, or has been

immersed in water. Contact Customer Tech Support for replacement or

repair.

3-POLE

GROUNDED

OUTLET

GROUNDING PIN

WARNING

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified

electrician or service provider if you are in doubt as to whether the product is properly grounded. Do not modify the plug

provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 110-120 Volt circuit and has a grounding plug that looks like the plug in the illustration.

Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used

with this product.

This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that

circuit and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple

outlets on one circuit. This treadmill should be used with a minimum 15-amp circuit.

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the

assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed

correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To

prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your treadmill’s serial number located on a white barcode

sticker near the on/off power switch and power cord and enter it in the space

provided below.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

SERIAL NUMBER:

WARNING

SERIAL NUMBER LOCATION

MODEL NAME: HORIZON TREADMILL

SPEAKERS

WATER BOTTLE HOLDER

GRIP PULSE HANDRAILS

CONSOLE FAN

ON/OFF SWITCH

TRANSPORT WHEEL

POWER CORD

TABLET/READING RACKS

CONTROL PANEL AND DISPLAY WINDOWS

SAFETY KEY PLACEMENT

MOTOR COVER

RUNNING BELT/RUNNING DECK

SIDE RAIL

ROLLER END CAP

REAR ROLLER

TENSION/ALIGNMENT BOLTS

CONSOLE MAST

FOOT LOCK LATCH (UNDERNEATH DECK)

FOOT LOCK LATCH DECAL

(UNDERNEATH FOOT LATCH)

WATER BOTTLE HOLDER

ACCESSORY TRAY

CONSOLE

LOWER CONSOLE

MAST COVERS

KEEP HANDS AND FEET

AWAY FROM THIS AREA.

HIGH-PRESSURE SHOCKS

COULD

CAUSE BODILY INJURY.

CAUTION

MANTENGA LAS MANOS

Y LOS PIES ALEJADOS DE

ESTA ÁREA. DESCARGAS

DE ALTA PRESIÓN PODRÍAN

OCASIONAR LESIONES

FÍSICAS.

PRECAUCIÓN

GARDEZ VOS MAINS ET

VOS PIEDS À L’ÉCART DE

CET ENDROIT. DES COUPS

À HAUTE PRESSION

PEUVENT CAUSER DES

BLESSURES CORPORELLES.

ATTENTION

TOOLS INCLUDED:

F 6 mm T-Wrench

F 5 mm L-Wrench

PARTS INCLUDED:

F 1 Console Assembly

F 2 Console Masts

F 2 Lower Console Mast Covers

F 1 Accessory Tray

F 1 Hardware Kit

F 1 Safety Key

F 1 Audio Adapter Cable

F 1 Bottle of Silicone Lubricant

(for 2 applications)

F 1 Crossbar

F 1 Power Cord

F 2 Console Connection Covers

If you have questions or

if there are any missing

parts, contact Customer

Tech Support. Contact

information is located on the

back panel of this manual.

DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift

treadmill from packaging until specified to do so in the assembly

instructions. You may remove the plastic wrap from console masts.

WARNING

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place

a protective covering on your floor. Take CAUTION when handling and transporting

this unit. Never open box when it is on its side. Once the banding straps have been

removed, do not lift or transport this unit unless it is fully assembled and in the

upright folded position, with the lock latch secure. Unpack and assemble the unit

where it will be used. The enclosed treadmill is equipped with high-pressure shocks

and may spring open if mishandled. Never grab hold of any portion of the incline

frame and attempt to lift or move the treadmill.

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

WARNING

NEED HELP?

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and

partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any

grease, such as lithium bike grease is recommended.

PRE ASSEMBLY

ASSEMBLY STEP 1

A Cut the yellow banding straps and lift the running

deck upward from the rear to remove all contents

from underneath the running deck.

B Open HARDWARE FOR STEP 1.

C Slide LEFT CONSOLE MAST BOOT (3) on to

LEFT CONSOLE MAST (1).

D Attach LEFT CONSOLE MAST (1) to MAIN FRAME

(2) using 3 BOLTS (A).

HARDWARE FOR STEP 1

PART TYPE DESCRIPTION QTY

M8X1.25PX60L 3A HEX SOCKET BOLT

NOTE: Do not fully tighten bolts until STEP 5.

ASSEMBLY STEP 2

A Open HARDWARE FOR STEP 2.

B Slide RIGHT CONSOLE MAST BOOT (5) on to

RIGHT CONSOLE MAST (4).

C Pull CONSOLE CABLE (3) away from the

treadmill base frame. Connect the CONSOLE

CABLE (3) from the MAIN FRAME (2) to the

CONSOLE CABLE (3) in the bottom of the

RIGHT CONSOLE MAST (4). The other end of

the CONSOLE CABLE (3) should be located at

the top of the mast.

D Attach RIGHT CONSOLE MAST (4) to MAIN

FRAME (2) using 3 BOLTS (A).

NOTE: Be careful not to pinch the console

cable while attaching the right console mast.

HARDWARE FOR STEP 2

PART TYPE DESCRIPTION QTY

M8X1.25PX60L 3A HEX SOCKET BOLT

NOTE: Do not fully tighten bolts until STEP

ASSEMBLY STEP 3

A Open HARDWARE FOR STEP 3.

B With the larger holes of the CROSSBAR (1)

facing upward, attach the LEFT SIDE of the

CROSSBAR (1) to the UPRIGHT MAST (2)

loosely using 2 BOLTS (A).

C Attach RIGHT SIDE of the CROSSBAR (1)

to the UPRIGHT MAST (3) loosely using

2 BOLTS (A).

NOTE: Do not tighten bolts completely

until after the console is assembled.

HARDWARE FOR STEP 3

PART TYPE DESCRIPTION QTY

M6X1.0PX15L 4A HEX SOCKET BOLT

ASSEMBLY STEP 4

A Open HARDWARE FOR STEP 4.

B Gently place the CONSOLE (5) on top of the

CONSOLE MASTS (1&4). Attach the LEFT SIDE

first using 2 BOLTS (A), 2 SPRING WASHERS (B)

and 2 FLAT WASHERS (C).

C The CONSOLE CABLES (6) are tucked into the

CONSOLE MAST (4). Using the lead wire

carefully pull the CONSOLE CABLE (6) out of

the CONSOLE MAST (4). Detach and discard the

LEAD WIRE. Connect the CONSOLE CABLES (6)

and carefully tuck wires in masts to avoid damage.

D Attach the RIGHT SIDE of the CONSOLE (5) using 2

BOLTS (A), 2 SPRING WASHERS (B) and 2 FLAT

WASHERS (C).

E Pull the top of the CONSOLE (5) towards the back of

the treadmill and HOLD while TIGHTENING THE

LEFT AND RIGHT SIDE BOLTS (A).

NOTE: Be careful not to pinch any

wires while assembling the console.

HARDWARE FOR STEP 4

PART TYPE DESCRIPTION QTY

M8X1.25PX15L 4A BOLT

8.2X15.0X1.2T

4B SPRING WASHER

8.2X13.5X2.0T

4C FLAT WASHER

A B C

(STEP E)

ASSEMBLY STEP 5

A Open HARDWARE FOR STEP 5.

B Attach the RIGHT AND LEFT SIDE CONSOLE

JOINT COVERS (1) using 8 SCREWS (A & B).

C REMEMBER to tighten CROSSBAR BOLTS into the

CONSOLE MASTS (2&3) completely now that

console assembly is finished.

HARDWARE FOR STEP 5

PART TYPE DESCRIPTION QTY

4X10L 4A SCREW

4X15L 4B SCREW

A Open HARDWARE FOR STEP 5.

B Attach the ACCESSORY TRAY (1) to the CROSSBAR (2)

using 4 SCREWS (A).

ASSEMBLY STEP 6

HARDWARE FOR STEP 4

PART TYPE DESCRIPTION QTY

4X15L

4A SCREW

ASSEMBLY STEP 7

A Open HARDWARE FOR STEP 6.

B REMEMBER to tighten CROSSBAR BOLTS into the

CONSOLE MASTS(3&4) completely now that

assembly is finished. Lift DECK (1) to upright

and locked position.

C Slide LEFT CONSOLE BOOT (2) to the bottom of

the LEFT CONSOLE MAST(3). Attach with 2

BOLTS (A) through the holes in LEFT CONSOLE

BOOT(2) into LEFT UPRIGHT MAST(3).

D Slide RIGHT CONSOLE BOOT (5) to the bottom

of the RIGHT CONSOLE MAST(4). Attach

with 2 BOLTS (A) through the holes in RIGHT

CONSOLE BOOT(5) into RIGHT UPRIGHT

MAST(4).

ASSEMBLY COMPLETE!

Before the first use, lubricate the treadmill

deck by following the instructions in

the MAINTENANCE section in the

TREADMILL GUIDE.

HARDWARE FOR STEP 5

PART TYPE DESCRIPTION QTY

4X10L 4A SCREW

TREADMILL OPERATION

This section explains how to use your treadmill’s console and programming.

The BASIC OPERATION section in the TREADMILL GUIDE has instructions for the following:

• LOCATION OF THE TREADMILL

• USING THE SAFETY KEY

• FOLDING THE TREADMILL

• MOVING THE TREADMILL

• LEVELING THE TREADMILL

• TENSIONING THE RUNNING BELT

• CENTERING THE RUNNING BELT

• USING THE HEART RATE FUNCTION

L M

DH IJ OK K

QP R

T UU E

CONSOLE FEATURES

Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

A) LCD DISPLAY WINDOWS: Incline, Speed, Time, Distance, Calories, Heart Rate

B) LED DISPLAY: Incline, Speed, Time, Distance, Calories, Heart Rate

C) PROGRAM INDICATORS: shows which program is currently selected.

D) START: press to begin exercising, start your workout, or resume exercising after pause.

E) STOP: press to pause/end your workout. Hold for 3 seconds to reset the console.

F) ENTER: press this button to confirm settings and selections during programming.

G) DISPLAY: this button changes the LED display information between (Incline/Segment Time/Speed) and (Distance/Total

Time/Speed).

H) INCLINE +/- KEYS: used to adjust incline in small increments (0.5% increments).

I) SPEED +/- KEYS: used to adjust speed in small increments (0.1 mph increments).

J) SPLIT: press this key to reset the Segment Time count-up timer to 0 seconds.

K) INTERVAL KEYS: these are programmable keys. When an user is selected, they can be programmed to a desired speed

and incline setting.

L) INCLINE QUICK KEYS: used to reach desired incline more quickly.

M) SPEED QUICK KEYS: used to reach desired speed more quickly.

N) FAN KEY: press to turn fan on and off.

O) FAN: personal workout fan.

P) AUDIO OUT / HEADPHONE JACK: plug your headphones into this jack to listen to your music through the headphones.

Note: when headphones are plugged into the headphone jack the sound will no longer come out through the speakers.

Q) AUDIO IN JACK: plug your CD / MP3 player into the console using the included audio adaptor cable.

R) USB INPUT: 1A/5V USB output power.

S) TABLET/READING RACK: holds tablet or reading material.

T) BLUETOOTH INDICATOR LIGHT: informs user that the Bluetooth connection as been made.

U) HEART RATE PULSE GRIPS: used to measure heart rate.

DISPLAY WINDOWS

This unit has a large LCD window and a set of LED’s to display all your workout information. There are small LED indicators

next to the lower LED displays to show which information is currently displayed.

• INCLINE: Shown as percent. Indicates the incline of your walking or running surface.

• DISTANCE: Shown as miles. Indicates distance traveled or distance remaining during your workout.

• SEGMENT TIME: The SEGMENT TIME is a count-up timer. It starts at 0 seconds and counts up until you press the SPLIT

KEY or one of the INTERVAL KEYS which will reset it to 0 seconds.

• TOTAL TIME: Total workout time.

• SPEED: Shown as MPH. Indicates how fast your walking or running surface is moving.

CUSTOM BUTTONS

• INTERVAL 1 & 2 BUTTONS: Programmable speed and incline settings. Select a user; start the machine; use the controls

to set the machine to the desired speed and incline; hold the desired interval key for 3 seconds until the console beeps.

Pressing this key during a workout will also automatically set the Segment Time to 0 seconds.

• SPLIT: press this key to reset the SEGMENT TIME count-up timer to 0 seconds.

La page charge ...

Horizon Fitness T303-2 Le manuel du propriétaire

Marque: Horizon Fitness

Modèle: T303-2

Catégorie: Fitness, gymnastique

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Horizon Fitness T303-2 Owner's manual
español: Horizon Fitness T303-2 El manual del propietario

Horizon Fitness T303-2 Le manuel du propriétaire

Horizon Fitness T303-2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents