Hitachi H 60MRV Manuel utilisateur

Marque: Hitachi

Modèle: H 60MRV

Catégorie: Marteaux rotatifs

Taper: Manuel utilisateur

Ce manuel convient également à

H 60MR

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité

de ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser

l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs

avant qu’ils utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual before operating the power tool. Please keep this

manual available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de que utilicen la

herramienta eléctrica.

H60MRV

Model Demolition Hammer

Modèle Marteau piqueur

Modelo Martillo demoledor

H 60MR

•

H 60MRV

01Eng_H60MR_US 10/26/07, 18:371

English

CONTENTS

Page

IMPORTANT SAFETY INFORMATION ...... 3

MEANINGS OF SIGNAL WORDS .............. 3

SAFETY ............................................................ 4

GENERAL SAFETY RULES ......................... 4

SPECIFIC SAFETY RULES AND

SYMBOLS.............................................. 6

DOUBLE INSULATION FOR SAFER

OPERATION .......................................... 8

FUNCTIONAL DESCRIPTION ......................... 9

NAME OF PARTS ........................................ 9

SPECIFICATIONS ........................................ 9

Page

ASSEMBLY .................................................... 10

OPERATION .................................................. 12

APPLICATIONS ......................................... 12

PRIOR TO OPERATION ............................. 12

HOW TO USE THE DEMOLITION

HAMMER ............................................. 13

MAINTENANCE AND INSPECTION ............. 14

ACCESSORIES .............................................. 16

STANDARD ACCESSORIES ..................... 16

OPTIONAL ACCESSORIES ....................... 16

TABLE DES MATIERES

Page

INFORMATIONS IMPORTANTES DE

SÉCURITÉ ............................................ 18

SIGNIFICATION DES MOTS

D’AVERTISSEMENT ........................... 18

SECURITE ...................................................... 19

REGLES GENERALES DE SECURITE ....... 19

REGLES DE SECURITE SPECIFIQUES

ET SYMBOLES .................................... 21

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR ........ 23

DESCRIPTION FONCTIONNELLE ................ 24

NOM DES PARTIES .................................. 24

SPECIFICATIONS ...................................... 24

Page

ASSEMBLAGE .............................................. 25

FONCTIONNEMENT ..................................... 27

APPLICATIONS ......................................... 27

AVANT L’UTILISATION ............................ 27

COMMENT UTILISER LE MARTEAU

PIQUEUR ............................................. 28

ENTRETIEN ET INSPECTION ....................... 29

ACCESOIRES ................................................. 31

ACCESSOIRES STANDARD ..................... 31

ACCESSOIRES SUR OPTION ................... 31

ÍNDICE

Página

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD ........................................ 33

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN................................... 33

SEGURIDAD .................................................. 34

NORMAS GENERALES DE SEGURIDAD

............................................................. 34

NORMAS Y SÍMBOLOS ESPECÍFICOS

DE SEGURIDAD .................................. 36

AISLAMIENTO DOBLE PARA OFRECER

UNA OPERACIÓN MÁS SEGURA ..... 38

DESCRIPCIÓN FUNCIONAL ......................... 39

NOMENCLATURA ..................................... 39

ESPECIFICACIONES .................................. 39

Página

MONTAJE ..................................................... 40

OPERACIÓN .................................................. 42

APLICACIONES ......................................... 42

ANTES DE LA OPERACIÓN ...................... 42

FORMA DE USAR EL MARTILLO

DEMOLEDOR ...................................... 43

MANTENIMIENTO E INSPECCIÓN .............. 44

ACCESORIOS ................................................ 46

ACCESORIOS ESTÁNDAR ....................... 46

ACCESORIOS OPCIONALES .................... 46

English

Español

Français

01Eng_H60MR_US 10/26/07, 18:372

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situation which, if ignored, could result in death

or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

01Eng_H60MR_US 10/26/07, 18:373

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) Double Insulated tools are equipped with a polarized plug (one blade is wider than

the other.) This plug will fit in a polarized outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install a polarized outlet. Do not change the plug in any way. Double

Insulation

eliminates the need for the three wire grounded power cord and

grounded power supply system.

(2) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

(3) Don’t expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the plug from

a receptacle. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

(5) When operating a power tool outside, use an outdoor extension cord marked “W-

A” or “W”. These cords are rated for outdoor use and reduce the risk of electric

shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools

with your finger on the switch or plugging in tools that have the switch on invites

accidents.

01Eng_H60MR_US 10/26/07, 18:374

English

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead

to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect the plug from the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures reduce

the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hand of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(7) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tools operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

(8) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

on another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instruction may create a risk of electric shock or injury.

01Eng_H60MR_US 10/26/07, 18:375

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

2. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

3. Never touch moving parts.

Never place your hands, fingers or other body parts near the tool’s moving parts.

4. Never operate without all guards in place.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

5. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

6. Never use a power tool for applications other than those specified.

Never use a power tool for applications other than those specified in the Instruction

Manual.

7. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

8. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

9. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

10. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to yourself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

11. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all times.

Check for dust build-up frequently.

12. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may burn

out.

01Eng_H60MR_US 10/26/07, 18:376

English

13. Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

14. Never leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

15. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

16. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

17. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

18. NEVER touch the tool bit with bare hands after operation.

19. NEVER wear gloves made from materials likely to roll up such as cotton, wool, cloth or

string, etc.

20. ALWAYS attach the side handle and securely grip the Demolition Hammer.

21. ALWAYS be careful with buried object such as an underground wiring.

Touching live wiring or electric cable with this tool may result in electric shock.

Confirm before use whether hidden objects are present, such as electric cables within

the wall, floor or ceiling.

22. Definitions for symbols used on this tool

V ............. volts

Hz ........... hertz

A ............. amperes

no .......... no load speed

W ............ watt

............ Class II Construction

---/min .... revolutions per minute

........... Alternating current

01Eng_H60MR_US 10/26/07, 18:377

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation” means that two physically separated insulation systems have

been used to insulate the electrically conductive materials connected to the power supply

from the outer frame handled by the operator. Therefore, either the symbol “

” or the

words and “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in

wet environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy water,

and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic

may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

01Eng_H60MR_US 10/26/07, 18:378

English

Fig. 1

Model H60MR H60MRV

Motor Single-Phase, Series Commutator Motor

Power Source Single-Phase, 120 V AC 60Hz

Current 11.8 A 12.5 A

Full-load Impact Rate 1,650/min. 930 – 1,650/min.

Weight 23.1 lbs (10.5 kg)

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

NAME OF PARTS

SPECIFICATIONS

Nameplate

Side Handle

Front Cap

Grip (B)

Grip (A)

Trigger Switch

Stopper

Dial (H60MRV)

Tail Cover

Housing

Brush Cap

(Under the Tail Cover)

Handle

01Eng_H60MR_US 10/26/07, 18:379

English

ASSEMBLY

CAUTION: To prevent accidents, make

sure to turn the switch off and

disconnect the plug from the

receptacle.

NOTE:

When using tools such as bull points,

cutters, etc., make sure to use the genuine

parts designated by our company.

1. Installing Tools

(1) Clean the shank portion of the tool.

(2) As shown in Fig. 2, pull grip (A) in the

direction of A, and insert the tool into a

hole of the front cap.

(3) Adjust the groove position while turning

the tool, and furthermore insert it until it

hits the end of the hole.

(4) Return grip (A) to its original position, pull

the tool to make sure it is locked

completely. (Fig. 3)

2. Deciding Working Position of Tool

The tool can be turned every 30 degrees

and can be fixed at the position of 12

steps.

(1) As shown in Fig. 4, the blade angle can

be freely changed if the grip (A) is turned

in the direction of B in a state where grip

(B) is slid in the direction of A.

(2) Release grip (B) and turn the tool, and

make sure that it is locked completely.

3. Removing Tool

As shown in Fig. 2, pull grip (A), and pull

out the tool.

Fig. 2

Grip (A)

Tool Shank

Front Cap

Fig. 3

Fig. 4

Grip (B)

Grip (A)

01Eng_H60MR_US 10/26/07, 18:3710

English

4. Move the side handle

The side handle can be fixed at any

desired position; 360 degrees, and can

also be fixed at any position in the back-

and-forth direction.

(1) Loosen the handle by turning the grip in

the direction of A as shown in Fig. 5.

(2) Adjust it to a position where vertical (up-

and-down) operation can be facilitated as

illustrated in Fig. 6, Fig. 7, and Fig. 8.

(3) Turn the grip in the direction of B and fix

the handle.

Fig. 7 Fig. 8

Fig. 5 Fig. 6

Grip

01Eng_H60MR_US 10/26/07, 18:3711

English

OPERATION

APPLICATIONS

䡬 Demolishing concrete, chiseling concrete, grooving, bar cutting, and driving piles.

Application examples:

Installation of piping and wiring, sanitary facility installation, machinery installation,

water supply and drainage work, interior jobs, harbor facilities and other civil engineering

work.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle

while the switch is in the ON position, the power tool will start operating immediately

and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as short as

practicable.

WARNING: Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a faulty receptacle is used, it may cause overheating, resulting in a serious

hazard.

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

6. Select the number of strikes (applicable only to H60MRV) (Fig. 9)

01Eng_H60MR_US 10/26/07, 18:3712

English

HOW TO USE THE DEMOLITION HAMMER

1. After placing the tip of the tool on concrete surface, switch

ON.

The switch can be turned ON if the trigger is pulled and OFF

when it is released.

If the stopper is pressed while the trigger for the switch is

pulled, even if your finger is released from the trigger, the

switch remains ON - convenient for continuous operation.

To turn the switch OFF, pull the trigger again, and then the

stopper comes off.

2. By utilizing the empty weight of the machine and by firmly

holding the demolition hammer with both hands, one can

effectively control the subsequent recoil motion.

Proceed at a moderate work-rate, the use of too much force will impair efficiency.

CAUTION: After long time of use, the cylinder case becomes hot.

Therefore, be careful not to burn your hands.

Standard number of strikes

Dial Number of strikes/min.

6 1,650

5 1,590

4 1,460

3 1,320

2 1,110

1 930

Fig. 9 (H60MRV)

Dial

Fig. 10

CAUTION: Do not make any adjustment of the dial during operation. Holding the main

body with one hand can swing you around, resulting in an injury.

This machine has an electronic controlled circuit built-in, enabling stepless regulation

of the number of strikes. Make the most of this machine by adjusting the dial according

to the working contents; chiseling, demolishing, or the quality of the material to be

chiseling or demolishing.

The scale “1” of the dial is for the minimum speed with 930 strikes per minute, and the

scale “6” is for the maximum speed with 1,650 strikes per minute.

01Eng_H60MR_US 10/26/07, 18:3713

English

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the

receptacle during maintenance and inspection.

1. Inspecting the tool

Since use of a dull tool will degrade efficiency and cause possible motor malfunction,

sharpen or replace the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that they are properly tightened.

Should any of the screws be loosened, retighten them immediately.

WARNING: Using this demolition hammer with loosen screws is extremely

dangerous.

3. Inspecting the carbon brushes (Fig. 11)

The Motor employs carbon brushes which

are consumable parts. When they become

worn to or near the “wear limit”, it could

result in motor trouble. When an auto-stop

carbon brush is equipped, the motor will

stop automatically. At that time, replace

both carbon brushes with new ones which

have the same carbon brush Numbers

shown in the figure. In addition, always

keep carbon brushes clean and ensure that

they slide freely within the brush holders.

NOTE: Use HITACHI carbon brush No. 74 indicated in Fig. 11.

4. Replacing carbon brushes (Refer to figure for name of parts)

Loosen the set screw then remove the tail cover. By loosening the brush caps, the

carbon brushes can be removed. After fitting new carbon brushes, properly retighten

the brush caps and mount the tail cover.

5. Grease replacement

This machine is of fully oil sealed construction to protect against dust incursion and to

prevent lubricant leakage. This machine can be used without grease replenishment for

an extended period of time. However, perform the grease replacement to extend the

service life. Replace the grease as described below.

(1) Grease Replacement Period

Inspect the grease amount according to the timing replacement period of the carbon

brush. (See item 3 in the section MAINTENANCE AND INSPECTION.)

Ask for grease replacement at the nearest authorized Hitachi Service Center.

In the case that you are forced to change the grease by yourself, please follow the

following points.

Wear limit

0.28” (7 mm)

No. of carbon

brush

0.67” (17 mm)

Fig. 11

01Eng_H60MR_US 10/26/07, 18:3714

English

(2) How to replace grease

CAUTION:

䡬 Before replacing the grease, turn the power off and pull out the plug from the receptacle.

1 Disassemble the crank case cover and the

crank cover and thoroughly wipe off the

old grease inside.

2 Supply 2.7 oz (80 g) (the standard volume

to cover the connecting rod) of Hitachi

Electric Hammer Grease A in the crank

case.

3 After replacing the grease, reassemble the

crank case cover and the crank cover

securely. At this time, do not damage or

lose the oil seal.

NOTE:

䡬 The Hitachi Electric Hammer Grease A is of the low viscosity type. When the grease is

consumed, purchase from the authorized Hitachi Service Center.

䡬 Do not excessively supply the designated amount of grease. Otherwise, the tool should

not operate accurately.

6. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

7. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried

out by a Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi

Authorized Service Center when requesting repair or other maintenance. In

the operation and maintenance of power tools, the safety regulations and

standards prescribed in each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the latest

technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior

notice.

Crank Case Cover

Fig. 12

Crank Cover

01Eng_H60MR_US 10/26/07, 18:3715

English

ACCESSORIES

WARNING: ALWAYS use Only authorized HITACHI replacement parts and

accessories. NEVER use replacement parts or accessories which are

not intended for use with this tool. Contact HITACHI if you are not sure

whether it is safe to use a particular replacement part or accessory

with your tool.

The use of any other attachment or accessory can be dangerous and

could cause injury or mechanical damage.

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

(1) Bull Point (SDS max shank) (Code No. 313471) ................................................................ 1

(2) Case (Code No. 324049) ...................................................................................................... 1

(3) Side Handle (Code No. 317103) .......................................................................................... 1

OPTIONAL ACCESSORIES........ sold separately

䡬 Demolishing

(1) Bull Point (SDS max shank type)

䡬 Groove digging and edging

(1) Cold chisel (SDS max shank type)

Overall Length 11-1/32" (280 mm) 15-3/4" (400 mm)

Code No. 313473 313474

Overall Length 11-1/32" (280 mm) 15-3/4" (400 mm)

Code No. 313471 313472

01Eng_H60MR_US 10/26/07, 18:3716

English

䡬 Asphalt Cutting

(1) Cutter (SDS max shank type)

䡬 Scooping Work

(1) Scoop (SDS max shank type)

䡬 Surface Roughing

䡬 Tamping

䡬 Hammer Grease A

70g (in a tube) (Code No. 981840)

30g (in a tube) (Code No. 308471)

NOTE:

Specifications are subject to change without any obligation on the part of the HITACHI.

(1) Bushing Tool

(Code No. 313477)

(2) Shank

(Code No. 313479)

(1) Rammer

(Code No. 313478)

(2) Shank

(Code No. 313479)

Overall Length 15-3/4" (400 mm)

Code No. 313475

Overall Length 15-3/4" (400 mm)

Code No. 313476

01Eng_H60MR_US 10/26/07, 18:3717

Français

INFORMATIONS IMPORTANTES DE SÉCURITÉ

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions

de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé

proviennent d’un non respect des règles ou précautions de base de sécurité. Un accident

peut la plupart du temps être évité si l’on reconnaît une situation de danger potentiel avant

qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE”

de ce mode d’emploi et dans les sections qui contiennent les instructions de fonctionnement

et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un

endommagement de la machine sont identifiés par AVERTISSEMENTS sur l’outil motorisé

et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement

recommandée par HITACHI.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont

ignorées, pourraient entraîner la mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées,

peuvent entraîner de mineures et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

02Fre_H60MR_US 10/26/07, 18:3818

Français

SECURITE

REGLES GENERALE DE SECURITE

AVERTISSEMENT: Lire et coxmprendre toutes les instructions.

Un non respect de toutes les instructions ci-dessous peut

entraîner une électrocution, un incendie et/ou de sérieuses

blessures personnelles.

CONSERVER CES INSTRUCTIONS

1. Zone de travail

(1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les

zones sombres invitent aux accidents.

(2) Ne pas utiliser les outils motorisés dans une atmosphère explosive, telle qu’en

présence de liquides inflammables, de gaz ou de poussières. Les outils motorisés

créent des étincelles qui risquent d’enflammer la poussière ou les vapeurs.

(3) Tenir les spectateurs, les enfants et les visiteurs éloignés, lors de l’utilisation de

l’outil motorisé. Une distraction peut faire perdre le contrôle de la machine.

2. Sécurité électrique

(1) Les outils à double isolation sont équipés d’une fiche polarisée (une lame est plus

large que l’autre). Cette fiche ne pénétrera dans une prise secteur polarisée que

dans un sens. Si la fiche ne rentre pas complètement dans la prise, la retourner. Si

elle ne rentre toujours pas, contacter un électricien qualifié pour installer une prise

polarisée. Ne pas modifier la fiche d’aucune façon. La double isolation

élimine

le besoin d’un cordon d’alimentation à trois fils et d’un système d’alimentation

avec mises à la terre.

(2) Eviter tout contact corporel avec les surfaces mises à la terre telles que les

canalisations, les radiateurs, les réchauds et les réfrigérateurs. Il y a un risque

accru d’électrocution si son corps est mis à la terre.

(3) Ne pas exposer les outils motorisés à la pluie ou à l’humidité. De l’eau pénétrant à

l’intérieur de l’outil motorisé augmente le risque d’électrocution.

(4) Ne pas maltraiter le cordon d’alimentation. Ne jamais utiliser le cordon pour porter

les outils ou tirer sur la fiche du réceptacle. Garder le cordon à l’écart de la chaleur,

de l’huile, des arêtes coupantes ou des pièces en mouvement. Remplacer les

cordons endommagés immédiatement. Des cordons endommagés augmentent le

risque d’électrocution.

(5) Lors de l’utilisation d’un outil motorisé, utiliser un cordon de rallonge extérieur

marqué “W-A” ou “W”. Ces cordons sont prévus pour une utilisation extérieure et

réduisent les risques d’électrocution.

3. Sécurité personnelle

(1) Rester sur ses gardes, regarder ce que l’on fait et utiliser son sens commun lors de

l’utilisation d’un outil motorisé. Ne pas utiliser un outil en état de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un moment d’inattention lors

de l’utilisation de l’outil motorisé peut entraîner de sérieuses blessures personnelles.

(2) S’habiller correctement. Ne pas porter des vêtements larges ou des bijoux. Attacher

les cheveux longs. Tenir ses cheveux, vêtements et ses gants éloignés des parties

mobiles. Les vêtements larges, les bijoux et les cheveux longs peuvent se prendre

dans les parties mobiles.

02Fre_H60MR_US 10/26/07, 18:3819

Français

(3) Eviter tout démarrage accidentel. S’assurer que le l’interrupteur d’alimentation

est sur la position d’arrêt avant de brancher la machine. Transporter l’appareil

avec les doigts sur l’interrupteur d’alimentation ou brancher un outil avec

l’interrupteur sur la position marche invite aux accidents.

(4) Retirer les clefs d’ajustement ou les commutateurs avant de mettre l’outil sous

tension. Une clef qui est laissée attachée à une partie tournante de l’outil peut

provoquer une blessure personnelle.

(5) Ne pas trop présumer de ses forces. Garder en permanence une position et un

équilibre correct. Une position et un équilibre correct permettent un meilleur contrôle

de l’outil dans des situations inattendues.

(6) Utiliser un équipement de sécurité. Toujours porter des lunettes de protection.

Utiliser un masque à poussière, des chaussures de sécurité antidérapantes, un

couvre-chef dur ou des protections d’oreille dans les conditions appropriées.

4. Utilisation de l’outil et entretien

(1) Utiliser un étau ou toutes autres façons de fixer et maintenir la pièce à usiner sur

une plate-forme stable. Tenir la pièce avec la main ou contre son corps est instable

et peut conduire à une perte de contrôle de l’outil.

(2) Ne pas forcer sur l’outil. Utiliser l’outil correct pour l’application souhaitée. L’outil

correct réalisera un meilleur et plus sûr travail dans le domaine pour lequel il a été

conçu.

(3) Ne pas utiliser un outil s’il ne se met pas sous ou hors tension avec un interrupteur.

Un outil qui ne peut pas être commandé avec un interrupteur est dangereux et doit

être réparé.

(4) Déconnecter la fiche de la source d’alimentation avant de réaliser tout ajustement,

changement d’accessoires ou pour ranger l’outil. De telles mesures de sécurité

réduisent le risque que l’outil ne démarre accidentellement.

(5) Ranger les outils inutilisés hors de la portée des enfants et des autres personnes

inexpérimentées. Les outils sont dangereux dans les mains de personnes

inexpérimentées.

(6) Conserver les outils avec soin. Garder les outils de coupe aiguisés et propres. Des

outils bien entretenus, avec des lames coupantes aiguisées risquent moins de se

gripper et sont plus faciles à contrôler.

(7) Vérifier les défauts d’alignement ou grippage des parties mobiles, les ruptures

des pièces et toutes les autres conditions qui peuvent affecter le fonctionnement

des outils. En cas de dommage, faire réparer l’outil avant de l’utiliser. Beaucoup

d’accidents sont causés par des outils mal entretenus.

(8) Utiliser uniquement les accessoires recommandés par le fabricant pour le modèle

utilisé. Des accessoires qui peuvent convenir à un outil, peuvent devenir dangereux

lorsqu’ils sont utilisés avec un autre outil.

5. Réparation

(1) La réparation de l’outil ne doit être réalisée uniquement par un réparateur qualifié.

Une réparation ou un entretien réalisé par un personnel non qualifié peut entraîner

des risques de blessures.

(2) Lors de la réparation d’un outil, utiliser uniquement des pièces de rechange

identiques. Suivre les instructions de la section d’entretien de ce mode d’emploi.

L’utilisation de pièces non autorisées ou un non respect des instructions d’entretien

peut créer un risque d’électrocution ou de blessures.

02Fre_H60MR_US 10/26/07, 18:3820

La page charge ...

Hitachi H 60MRV Manuel utilisateur

Marque: Hitachi

Modèle: H 60MRV

Catégorie: Marteaux rotatifs

Taper: Manuel utilisateur

Ce manuel convient également à

H 60MR

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi H 60MRV User manual
español: Hitachi H 60MRV Manual de usuario

Hitachi H 60MRV Manuel utilisateur

Ce manuel convient également à

Hitachi H 60MRV Manuel utilisateur

dans d''autres langues

Documents connexes