Nikon ARROW ID 3000 Manuel utilisateur

Marque: Nikon

Modèle: ARROW ID 3000

Catégorie: Niveaux laser

Taper: Manuel utilisateur

Instruction manual/Manuel d’utilisation

English ......................................... p. 3-18

Français ...................................... p. 19-34

CONTENTS

English

[ Introduction]

Introduction ........................................................................ 4

Cautions before use ...................................................... 5-7

[Getting to know the Laser Rangefinder]

Key features ......................................................................... 8

Nomenclature/Composition ......................................... 9

Internal display ................................................................ 10

[First step]

Inserting/replacing battery .......................................... 11

[Mode settings]

Changing the distance display unit (m/YD) ........... 12

Changing the target priority mode ........................... 12

Changing the measurement display mode ............ 13

[Measurement]

Adjusting diopter ............................................................. 14

Measuring ........................................................................... 14

Single measurement ....................................................... 15

Continuous measurement ............................................ 15

[Technical notes]

Specifications ............................................................ 16-17

Troubleshooting/Repair ............................................... 18

● About the manual

・ No part of the manual included with this product may be reproduced, transmitted, transcribed, stored in a

retrieval system, or translated into any language in any form, by any means, without Nikon’s prior written

permission.

・Nikon will not be held liable for any errors this manual may contain.

・The appearance of this product and its specifications are subject to change without notice.

● About controls for radio interference

・This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

・This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules and to EU EMC directive. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

● About measurement results

This Nikon Laser Rangefinder is a basic rangefinder. Its results cannot be used as official evidence.

[Introduction]

Thank you for purchasing the Nikon Laser Rangefinder ARROW ID 3000.

Before using this product, please read these instructions thoroughly to ensure correct usage.

After reading, please keep this manual handy for easy reference.

Please observe the following

guidelines strictly so you can use

the equipment properly and

avoid potentially hazardous

problems. Before using this

product, read thoroughly the

“Cautions before use” and

instructions on correct usage

accompanying the product.

Keep this manual within reach

for easy reference.

WARNING

This indication alerts you to the fact

that any improper use ignoring the

contents described herein can result

in potential death or serious injury.

CAUTION

This indication alerts you to the fact

that any improper use ignoring the

contents described herein can result

in potential injury or material loss.

SAFETY PRECAUTIONS (Laser)

The Nikon Laser Rangefinder uses an

invisible laser beam. Be sure to

observe the following:

Warning

• Do not press the PWR button while

looking towards the optics from the

objective side. Failure to do this may

negatively affect or damage your

eyes.

• Do not aim at the eye.

• Do not point the laser at people.

• Do not look at the laser with another

optical instrument such as through

lenses or binoculars, nor with the

naked eye. This may result in damage

to the eyes.

• When not measuring, please

keep your fingers away from the

PWR button to avoid accidentally

emitting the laser beam.

• When not in use for an extended

period, please remove the battery

from the body.

• Do not disassemble/remodel/repair

the Nikon Laser Rangefinder. The

emitting laser may be harmful to

your health. A product that has been

disassembled/remodeled/repaired is

not guaranteed by the manufacturer.

• Keep the Nikon Laser Rangefinder

out of reach of children when

stored.

• If the Nikon Laser Rangefinder’s

body cover is damaged, or if it

emits a strange sound due to

dropping or some other cause,

remove the battery immediately

and stop using.

￭ Cautions before use

SAFETY PRECAUTIONS

(Lithium battery)

If handled incorrectly, the battery

may rupture and leak, corroding

equipment and staining clothing.

Be sure to observe the following:

• Install the battery with the + and –

poles positioned correctly.

• The battery should be removed

when exhausted or during

extended periods of non-use.

• Do not short the end terminal of

the battery chamber.

• Do not carry together with keys

or coins in a pocket or bag, it may

short and cause overheating.

• Do not expose the battery to water,

or a flame. Never disassemble the

battery.

• Do not charge the lithium battery.

• If liquid from a damaged battery

comes into contact with clothing or

skin, rinse immediately with plenty

of water. If liquid from a damaged

battery enters the eyes, rinse

immediately with clean water, then

consult a doctor.

• When disposing of the battery,

follow your local area regulations.

this product or other small parts

out of reach of children.

• Prevent children from putting

the rubber eyecup or small parts,

etc. into their mouths. If children

swallow such parts, consult a

doctor immediately.

• If using the rubber eyecup for a

long period of time, some people

may suffer skin inflammation. If any

symptoms occur, stop using it and

consult a doctor immediately.

• When carrying the Nikon Laser

Rangefinder, store it in the case.

• If your Nikon Laser Rangefinder

should fail to operate correctly,

discontinue use immediately and

consult with your local dealer for

instructions on where to send it for

repair.

SAFETY PRECAUTIONS

(Monocular)

The Nikon Laser Rangefinder

employs a monocular in its optical

system in order to aim at the target.

Be sure to observe the following:

Warning

• Never look directly at the sun, an

intense light or the laser beam

when using the Nikon Laser

Rangefinder.

Cautions

• When not using the Nikon Laser

Rangefinder, do not push the

PWR button.

• Do not use this product while

walking. Failure to observe this

may cause injury or malfunction

as a result of walking into

something, hitting others, falling

or other accidents.

• Do not swing around by the

strap. This may result in hitting

others and cause injury.

• Do not place this product in

an unstable place. Failure to

observe this may result in falling

or dropping and cause injury or

malfunction.

• Keep the plastic bag used to wrap

Storage

• Water condensation or mold may

occur on the lens surface because

of high humidity. Therefore, store

the Nikon Laser Rangefinder in a

cool, dry place.

After use on a rainy day or at night,

thoroughly dry it at room

temperature, then store in a cool,

dry place.

CARE AND MAINTENANCE

Lenses

• When removing dust on the lens

surface, use a soft oil-free brush.

• When removing stains or smudges

like fingerprints from the lens

surface, wipe the lenses very gently

with a soft clean cotton cloth or

quality oil-free lens tissue. Use a

small quantity of pure alcohol (not

denatured) to wipe stubborn

smudges. Do not use velvet cloth

or ordinary tissue, as it may scratch

the lens surface. Once the cloth has

been used for cleaning the body, it

should not be used again for the

lens surface.

Main body

• Clean the body surface with a soft,

clean cloth after blowing away dust

with a blower* lightly. Do not use

benzene, thinner, or other cleaners

containing organic solvents.

* A blower is rubber cleaning

equipment that blows air from a

nozzle.

SAFETY PRECAUTIONS

Cautions

• This product is not designed for use

underwater.

• Rain, water, sand and mud should

be removed from the rangefinder

body surface as soon as possible,

using a soft, clean cloth.

• Do not leave the Nikon Laser

Rangefinder in a car on a hot or

sunny day, or near heat-generating

equipment. This may damage or

negatively affect it.

• Do not leave the Nikon Laser

Rangefinder in direct sunlight.

Ultraviolet rays and excessive heat

may negatively affect or even

damage the unit.

• Do not leave the eyepiece in direct

sunlight. The condenser effect of

the lens may damage the internal

display surface.

• If the Nikon Laser Rangefinder is

exposed to sudden changes in

temperature, water condensation

may occur on lens surfaces. Do

not use the product until the

condensation has evaporated.

This symbol indicates that this battery is to be

collected separately.

The following apply only to users in European

countries.

• This battery is designated for separate collection at an

appropriate collection point. Do not dispose of as

household waste.

• For more information, contact the retailer or the local

authorities in charge of waste management.

Symbol for separate collection applicable in European

countries

This symbol indicates that this product is to be

collected separately.

The following apply only to users in European

countries.

• This product is designated for separate collection at

an appropriate collection point. Do not dispose of as

household waste.

• For more information, contact the retailer or the local

authorities in charge of waste management.

Symbol for separate collection applicable in European

countries

[Getting to know the Laser Rangefinder]

￭ Key features

• Measurement range of actual distance:

5-500 meters/6-550 yards

• Horizontal Distance mode and Actual Distance

mode can be easily switched

• Target Priority Switching System for measuring

overlapping subjects

• High-quality 4x finder with multilayer coating

• Press and hold down the PWR button to activate the

continuous measurement function

• Automatic power shut-off (approx. 8 sec.

unoperated)

• Default to “Last Use” settings

• Rainproof — JIS/IEC protection class 4 (IPX4)

equivalent (under our testing conditions)

• Invisible/Eyesafe EN/IEC Class 1M Laser

The Nikon Laser Rangefinder uses an invisible

laser beam for measuring. It measures the time the

laser beam takes to travel from the rangefinder

to the target and back. Laser reflectivity and

measurement results may vary according to

climatic and environmental conditions, as well

as the color, surface finish, size, shape and other

characteristics of the target.

The following conditions facilitate measuring:

• Cloudy weather

• Bright-colored target

• Large-size target

• When laser incidence to the target’s reflective

surface is straight

Measurement may be inaccurate or fail in the

following cases:

• In snow, rain or fog

• Small or slender target

• Black or dark target

• Target has stepped surface

• Moving or vibrating target

• When measuring the surface of water

• Target measured through glass

• When the target is glass or a mirror

• When laser incidence to the target’s reflective

surface is oblique

■ Nomenclature/Composition

1. Monocular objective lens

2. Laser emission aperture

3. Laser detector aperture

4. MODE button

5. PWR button (POWER ON/Measurement

button)

6. Eyepiece

7. Eyecup/diopter adjustment ring

8. Diopter index

9. Strap eyelet

10. Battery chamber cover “Open” indication

11. Battery chamber cover

12. Product number label

13. Indication

• Body ...................................... x1

• Case .......................................x1

• Strap ......................................x1

• Lithium battery (CR2) ..... x1

Composition

￭ Internal display

 : Aim at the target you want to measure. Position the target at the center of the reticle.

 : Appears while the laser is being irradiated for a measurement.

Do not look towards the objective lens side while this mark is shown.



: "Failure to measure" or "Unable to measure"

* Because the internal display of this product is enlarged by the eyepiece, dust may sometimes be seen.

This will not, however, affect the measurement accuracy.

Unit of measure (m/yd.)

Target mark

Laser irradiation mark

Battery condition

Distance

First Target Priority mode

Distant Target Priority mode

Horizontal Distance mode

￭ Inserting/replacing battery

1. Type of battery

3V CR2 lithium battery x1

2. Inserting/replacing battery

2-1. Open the battery chamber cover

Rotate the battery chamber cover counterclockwise and remove it. It may not open easily due to its rubber

packing for water resistance.

2-2. Insert the battery/Replace the old battery with a new one

Insert a new battery correctly positioned following the indication seal inside the chamber.

The [-] pole should be positioned toward the inside of the chamber. If the battery is not inserted correctly,

the Nikon Laser Rangefinder will not operate. When replacing the battery, remove the old battery then insert

a new one.

2-3. Close the battery chamber cover

Rotate the battery chamber cover clockwise to screw it into the body. It may not close easily due to the

rubber packing for water resistance, but continue to turn it all the way until it stops. Confirm that the cover is

securely closed.

3. Battery level indicator

* The battery condition mark in the internal display warns when the battery needs to be replaced.

Display Description

After power on, displays for 2 seconds only.

Sufficient power available.

After power on, displays for 2 seconds only.

Power getting low.

Prepare to replace the battery.

Displayed continuously.

Low. Battery should be replaced with a new one.

Blinks. After blinking 3 times, automatically

powers o.

Power exhausted.

Replace the battery.

[First step]

■

Changing the distance display unit

(m/YD)

Factory default setting is yard (YD).

1. Turn on the power (Confirm the internal display is on).

2. Press and hold the MODE button for more than 2 seconds.

When the display unit has been switched, release the button.

■ Changing the target priority mode

This Nikon Laser Rangender employs the First Target Priority/Distant Target Priority switching system.

(Factory default setting is First Target Priority mode).

1.Turn on the power (Conrm the internal display is on)

2. Press and hold the MODE button, then depress and hold the PWR button within 0.5 second.

Continue to press and hold both button (more than 2 seconds) until First Target Priority mode and

Distant Target Priority mode are switched.

3. Release both buttons when the mode is switched.

*If the buttons are not pressed in the correct order, switching will not take place.

[First Target Priority mode/Distant Target Priority mode]

When measuring overlapping subjects:

First Target Priority mode displays the distance of the closest subject and

Distant Target Priority mode displays that of the farthest subject.

[Mode settings]

■ Changing the measurement display mode

Horizontal Distance mode and Actual Distance mode can be switched.

(Factory default setting is Horizontal Distance mode.)

1. Turn on the power (Confirm the internal display is on).

2. Press and hold the MODE button, then immediately (less than 0.5 secnd) depress the PWR button for less

than 2 seconds.

3. Release your finger from the PWR button to switch the Measrurement display mode.

*If the buttons are not pressed in the correct order, switching will not take place.

Horizontal

Distance

Horizontal Distance mode

Actual Distance mode

Actual

Distance

N/A

[Measurement]

Caution — Controls, adjustments or usage of procedures other than those specified herein may

produce negative effects or damage to your health due to laser radiation.

■

Measuring

1. Turn

on the power.

(Automatic power shut-off after approx. 8 seconds

unoperated.)

Immediately after power-on

2. Aim at the target.

Position the target at the center of the

target mark.

Standby

*Before measuring, be sure to confirm each mode setting.

Please refer to each section on how to set each mode.

■

Adjusting diopter

Adjust the diopter to obtain a clear internal display in the viewfinder.

First, rotate the diopter adjustment ring counterclockwise until it comes to a complete stop.

Next, turn on the power and rotate the diopter adjustment ring back and forth until the internal

display comes into focus.

3. Pressing the PWR button starts measurement.

After measurement, the result is displayed for approx. 8 seconds, then power automatically turns off.

If you press the

PWR button

during power-on, another measurement starts.

Press and hold down the

PWR button to start continuous measurement up to approx. 8 seconds.

During measurement, the measured result is displayed consecutively while the laser irradiation mark is

blinking. If you release your finger from the button, continuous measurement stops.

Example of measurement

failure

Example of measured

distance display

Pressing the PWR button once starts single measurement, then displays the results.

■ Single measurement

■ Continuous measurement

Single measurement

Press PWR button once

Press and hold down the PWR button

Continuous measurement

Standby

■ Specifications

Model ARROW ID 3000

Measurement system

Measurement range

(actual distance)

5-500 meters/6-550 yards

Distance display (increment) Every 1m/yd.

Optical system

Magnification (x) 4

Effective diameter of objective

lens (mm)

Angular field of view (real) (˚) 9.0

Eye relief (mm) 20.3

Exit pupil (mm) 5

Diopter adjustment ±4m

Others

Operating temperature (˚C/˚F) -10 — +50/14 — 122

Operating humidity (%RH) 80 or less (without dew condensation)

Power source

CR2 lithium battery x 1 (DC 3V)

Automatic power shut-off (after approx. 8 sec. unoperated)

Dimensions (L x H x W) (mm/in.) 91 x 73 x 37/3.6 x 2.9 x 1.5

Weight (g/oz.) Approx. 135/4.8 (without battery)

Structure JIS/IEC protection class 4 (IPX4) equivalent (under Nikon's testing conditions)*

Electromagnetic compatibility FCC Part15 SubPartB class B, EU:EMC directive, AS/NZS, VCCI classB, CU TR 020

Environment RoHS, WEEE

[Technical notes]

Model ARROW ID 3000

Laser

Laser classification

IEC60825-1: Class 1M/Laser Product

FDA/21 CFR Part 1040.10:Class I Laser Product

Wavelength (nm) 905

Pulse duration (ns) 20

Output (W) 10

Beam divergence (mrad) Vertical: 3.8, Horizontal: 0.17

* Water resistance performance

This Nikon Laser Rangefinder is equivalent to JIS/IEC protection class 4 (IPX4) (under our testing conditions). This rating

does not guarantee the water resistance performance of the unit or that it will be free from damage or problems under

all conditions. Please observe the following when using:

• The unit is not a sealed structure, so it should not be operated nor held in running water.

• If any moisture is found on movable parts of the unit, stop using it and wipe it off.

Battery life

Continuous operation: Approx. 8,000 times (at approx. 20°C)

This figure may differ according to conditions such as temperature and other factors. Use only as a guide.

・ The battery supplied with this Nikon Laser Rangefinder is for operation checking. Due to natural electrical discharge, the life of

this battery will likely be shorter than that noted above.

・ If water enters the battery chamber due to submersion, dry the battery chamber well, then replace the battery.

￭ Troubleshooting/Repair

If the Nikon Laser Rangefinder fails to function as expected, check the list below before consulting

your local dealer or the store where you purchased it.

● If there is a problem with the product.

Problem Cause/Solution

・Does not turn on

・Press the PWR button (top of the body).

・Check battery is inserted correctly.

・Replace the battery with a new one.

・Unable to measure

・Anomalous result

・Confirm each mode setting.

・Confirm if it can measure a large target close to you (example: a building

approx. 15m/yd. ahead of you).

・Clean the lens surface if necessary.

● If you require a repair, please contact your local dealer or the store where you purchased the product.

Do not repair or disassemble. It may result in a serious incident.

Please note that Nikon is not responsible for any direct or indirect damage if the user attempts repair

or disassembly.

Français

SOMMAIRE

[ Introduction]

Introduction ...................................................................... 20

Précautions avant utilisation ............................... 21-23

[Se familiariser avec le télémètre laser]

Caractéristiques principales ........................................ 24

Nomenclature/Composition ....................................... 25

Écran interne ..................................................................... 26

[Première étape]

Insérer/remplacer la pile .............................................. 27

[Configuration du mode]

Modifier les unités d'affichage de la distance

(m/YD) ................................................................................. 28

Modifier le mode de priorité à la cible .................... 28

Modifier le mode d'affichage de la mesure ............ 29

[Mesure]

Réglage dioptrique ........................................................ 30

Mesure ................................................................................ 30

Mesure unique ................................................................. 31

Mesure en continu .......................................................... 31

[Détails techniques]

Spécifications ............................................................ 32-33

Guide de dépistage des pannes/Réparations ...... 34

● A propos du manuel

・ Aucune section du manuel de ce produit ne peut être reproduite, transmise, transcrite ou enregistrée dans

un système d’enregistrement, ou traduit dans une autre langue, sous quelle que forme que ce soit, sans

l’autorisation écrite préalable de Nikon.

・Nikon ne saurait être tenu responsable des erreurs éventuelles présentes dans le manuel.

・L’apparence et les spécifications de ce produit sont sujets à modifications sans avertissement.

● A propos des contrôles d’interférences radio

・Cet appareil est conforme à la Partie 15 des Règles FCC. L'utilisation de cet appareil est soumise aux conditions

suivantes :

(1) Cet appareil ne doit pas provoquer des brouillages nuisibles et

(2) Cet appareil doit s'accommoder des brouillages auxquels il est soumis, y compris les brouillages qui peuvent

provoquer des anomalies de fonctionnement.

・Après essais, les caractéristiques de cet appareil ont été jugées comme entrant dans les limites des dispositifs

numériques de la classe B, telles que décrites à la Partie 15 des Règles FCC et de la directive EMC de l'UE. Ces

limites ont été fixées dans le but d'apporter une protection raisonnable contre les brouillages des appareils

domestiques. Cet appareil produit, utilise et peut émettre des fréquences radioélectriques; s'il n'est pas installé

conformément aux instructions, ces ondes peuvent perturber les radiocommunications. Toutefois, même en

cas d'installation conforme aux instructions, il peut arriver qu'un brouillage se produise en raison des conditions

particulières d'installation. Si cet appareil perturbe la réception des émissions de radio ou de télévision, ce dont

on peut s'assurer en le mettant sous tension puis hors tension, l'utilisateur est invité à prendre les mesures

correctives suivantes:

• Modifier l'orientation de l'antenne de réception ou changer son emplacement.

• Augmenter la distance séparant l'appareil du récepteur de radio ou de télévision.

• Consulter le distributeur ou un technicien de radio / télévision expérimenté.

Cet appareil numérique de la classe B est conforme à la norme canadienne relative aux équipements

susceptibles de provoquer des brouillages.

● A propos des résultats de mesure

Ce télémètre laser Nikon est un télémètre d'entrée de gamme. Ses résultats ne peuvent pas être utilisés comme

preuve officielle.

[Introduction]

Merci d’avoir choisi le télémètre laser Nikon ARROW ID 3000.

Avant d’utiliser ce produit, veuillez lire soigneusement ces instructions pour en garantir une utilisation correcte.

A la fin de votre lecture, gardez ce manuel à portée de main pour pouvoir vous y référer si nécessaire.

La page est en cours de chargement...

Nikon ARROW ID 3000 Manuel utilisateur

Marque: Nikon

Modèle: ARROW ID 3000

Catégorie: Niveaux laser

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Nikon ARROW ID 3000 User manual

Nikon ARROW ID 3000 Manuel utilisateur

Nikon ARROW ID 3000 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents