Explore Scientific Professional WIFI colour Weather Center 5-in-1 V Le manuel du propriétaire

Art.No.: WSX1001

Weather station • Stazione meteo • Wetterstation • Station météo • Estación meteorológica

5-in-1 WiFi

Professional Weather Station

EN

INSTRUCTION MANUAL ............... 2

IT

ISTRUZIONI PER L’USO ...............34

DE

BEDIENUNGSANLEITUNG ............ 68

FR

MODE D'EMPLOI .......................102

ES

MANUAL DE INSTRUCCIONES ...136

EN

INSTRUCTION MANUAL

ABOUT THIS INSTRUCTION MANUAL

These operating instructions are to be considered a component of the device.

Please read the safety instructions and the operating instructions carefully before use.

Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the

instruction manual must be provided to the new owner/user of the product.

This symbol represents a warning. To ensure safe use, always adhere to the instructions described in this

documentation.

This symbol is followed by a user’s tip.

GENERAL WARNINGS

• Risk of electric shock — This device contains electronic components that operate via a power source

(batteries). Children should only use the device under adult supervision. Only use the device as described

in the manual; otherwise, you run the risk of an electric shock.

• Choking hazard — Children should only use the device under adult supervision. Keep packaging

material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a

choking hazard.

• Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the batteries

correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes

and mucous membranes. In the event of contact, rinse the aected region immediately with a plenty of

water and seek medical attention.

• Risk of re/explosion — Do not expose the device to high temperatures. Use only the recommended

batteries. Do not short-circuit the device or batteries, or throw them into a re. Excessive heat or improper

handling could trigger a short-circuit, a re, or an explosion.

• Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will

contact the Service Centre and can send the device in to be repaired, if necessary.

• Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set

of batteries at full capacity. Do not use batteries from dierent brands or with dierent capacities. The

batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Base station, 5-in-1 Multisensor, AC/DC adapter (5V), 1x CR2032 battery (Backup battery)

BEFORE YOU BEGIN

• We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recommend

using lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power

requirements.)

• Insert batteries before rst use, matching the polarity in the battery compartment. Connect the AC/DC

adapter with the Base station and insert 1 CR2032 battery as backup power. 3x AA Batteries are required

for the 5-in-1 Multisensor.

TABLE OF CONTENTS

ABOUT THIS INSTRUCTION MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

GENERAL WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SCOPE OF DELIVERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

LCD DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

WIRELESS 5-IN-1 WEATHER SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

INSTALLATION AND SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

INSTALL WIRELESS 5-IN-1 WEATHER SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

POWER UP CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PAIRING WIRELESS 5-IN-1 WEATHER SENSOR & CONSOLE. . . . . . . . . . . . . . . . . . . . . . . . . . 9

PAIRING ADDITIONAL WIRELESS SENSOR(S) & CONSOLE (OPTIONAL) . . . . . . . . . . . . . . . . . . . 9

CREATE WEATHER SERVER ACCOUNT & SETUP WI-FI CONNECTION . . . . . . . . . . . . . . . . . . . . . . 9

CREATE WEATHER UNDERGROUND ACCOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CREATE WEATHERCLOUD ACCOUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

SETUP WI-FI CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SETUP THE WEATHER SERVER CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

ADVANCE SETTING IN WEB INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

VIEW YOUR WEATHER DATA IN WUNDERGROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

VIEWING YOUR WEATHER DATA IN WEATHERCLOUD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

FIRMWARE UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

OTHER SETTING & FUNCTIONS OF THE CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

MANUAL CLOCK SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

MOON PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

POINTING THE WIRELESS 5-IN-1 SENSOR TO SOUTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

SETTING ALARM TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ACTIVATING ALARM AND TEMPERATURE PRE-ALARM FUNCTION . . . . . . . . . . . . . . . . . . . . . 18

TEMPERATURE / HUMIDITY FUNCTION & TREND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

COMFORT INDICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

WIRELESS SENSOR SIGNAL RECEIVING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

WIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

WEATHER INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

WEATHER FORECAST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

BAROMETRIC PRESSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

RAINFALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

MAX / MIN DATA RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

PAST 24 HOURS HISTORY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

WEATHER ALERT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

BACKLIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

BATTERY REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

CLEANING THE RAIN COLLECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

CLEANING HYGRO-THERMO SENSOR OF WIRELESS 5-IN-1 SENSOR . . . . . . . . . . . . . . . . . . . 23

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

CONSOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

WIRELESS 5-IN-1 SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

EC DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

FCC DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

NOTES ON CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

WARRANTY & SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4

INTRODUCTION

Thank you for selecting the 5-in-1 WiFi Professional Weather Station. This system gathers and automatically

uploads accurate and detailed weather data to Weather Underground and Weathercloud website - the

famous weather service which allows weather observers to upload their local weather data with automated

personal weather stations (PWS) - at which you can access and upload your weather data freely. This

product oers professional weather observers or serious weather enthusiasts robust performance with a

wide range of options and sensors. You will get your own local forecast, high/lows, totals and averages for

virtually all weather variables without using a PC.

This weather station which transmits outdoor temperature, humidity, wind and rain data, which can add to a

sensor array of maximum 7 units, transmits your temperature & humidity to the console. The sensor is fully

assembled and calibrated for your easy installation. The sensor sends data at a low power frequency to the

console from up to 15m/450 feet away (line of sight).

In the console, a high-speed processor is embedded to analyze the received weather data and these real-

time data can be published to Wunderground.com and weathercloud.net through your home WiFi router.

The console can also synchronize with internet time server to keep the time and weather data time stamp

of high precision. The color background LCD display shows informative weather readings with advanced

features, such as high/low alert alarm, dierent weather index, and MAX/MIN records. With calibration and

moon phase feature, this system is truly a remarkably personal yet professional weather station for your own

backyard.

NOTE:

This instruction manual contains useful information on the proper use and care of this product. Please read

this manual through to fully understand and enjoy its features, and keep it handy for future use.

OVERVIEW

CONSOLE

1

2

3

4

6

7

5

8

12

13

10

14

21

20

19

15

16

23

24

17

18

22

11

9

5

1. [ ALARM/SNOOZE ] key

2. LCD display

3. [ HISTORY ] key

4. [ RAIN ] key

5. [ BARO ] key

6. [ MAX / MIN ] key

7. [ INDEX ] key

8. [ WIND ] key

9. Table stand

10. Wall mounting holder

11. [ ALERT ] key

12. [ ALARM ] key

13. [ CLOCK SET ] key

14. [ HI / LO / AUTO ] key

15. [ CHANNEL ] key

16. [ SENSOR / WI-FI ] key

17. Battery door

18. USB Power socket

19. [

] key

20. [

] key

21. [ RESET ] key

22. [ BARO UNIT ] key

23. [ REFRESH ] key

24. [ °C / °F ] slide switch

LCD DISPLAY

1

2

3

5

6

4

Display section:

1. Outdoor temperature & humidity

2. Weather forecast, Barometer, Wind

direction & speed

3. Weather index

4. Time, calendar & moon phase

5. Indoor / CH temperature & humidity

6. Rainfall & Rain rate

WIRELESS 5-IN-1 WEATHER SENSOR

1. Rain collector

2. Circular level

3. Antenna

4. Wind cups

5. Mounting pole

6. Radiation shield

7. Wind vane

8. Mounting base

9. Mounting clamp

10. Red LED indicator

11. [ RESET ] key

12. Battery door

13. Screws

1

2

3

5

8

9

4

7

6

12

10

11

13

6

RAIN GAUGE

1. Rain collector

2. Tipping bucket

3. Rain sensor

4. Drain holes

TEMPERATURE AND HUMIDITY SENSOR

1. Radiation shield Sensor casing

2. Temperature and humidity sensor (inside

the radiation shield)

1

2

WIND SENSOR

1. Wind cups (anemometer)

2. Wind vane

INSTALLATION AND SETUP

INSTALL WIRELESS 5-IN-1 WEATHER SENSOR

Your wireless 5-IN-1 sensor measures wind-speed, wind-direction, rainfall, temperature and

humidity for you. It’s assembled and calibrated for your easy installation.

INSTALL BATTERIES

Unscrew the battery door at bottom of unit and insert the

batteries according to the +/- polarity indicated.

Screw the battery door compartment on tightly.

NOTE:

- Ensure the water tight O-ring is properly aligned in place

to ensure water resistant.

- The red LED will begin ashing every 12 seconds.

7

ASSEMBLY OF THE STAND AND POLE

Step 1

Insert the top side of the pole to the square hole

of the weather sensor.

NOTE:

Ensure the pole and sensor's indicator align.

Step 2

Place the nut in the hexagon hole on the sensor,

then insert the screw in other side and tighten it

by the screw driver.

Step 3

Insert the other side of the pole to the square hole

of the plastic stand.

NOTE:

Ensure the pole and stand's indicator align.

Step 4

Place the nut in the hexagon hole of the stand,

then insert the screw in other side and then

tighten it by the screw driver.

8

Install the wireless 5-IN-1 sensor in an

open location with no obstructions above

and around the sensor for accurate

rain and wind measurement. Install

the sensor with the smaller end facing

the North to properly orient the wind

direction vane.

Secure the mounting stand and bracket

(included) to a post or pole, and allow

minimum 1.5m o the ground.

1.5 meter off

the ground

Add rubber

pads before

mount on

the pole

Point to

NORTH

POWER UP CONSOLE

Your console can pair up with the wireless 5-IN-1 outdoor weather sensor and up to 7 optional

wireless sensors. (Not included)

INSTALL THE BACKUP BATTERY

1. Remove the battery door of the console.

2. Insert a new CR2032 battery as per the polarity information marked on the battery

compartment.

3. Replace the battery door.

NOTE:

The backup battery can backup: Time & Date, Max/Min & Past 24 hours weather records, Alert

setting values, oset value of weather data and Sensor(s) channel history.

The built-in memory can backup: Router setting and Weather server setting.

POWER UP THE CONSOLE

1. Plug the power adapter USB plug to power up

the main unit.

2. Once the main unit power up, all the segments

of the LCD will be shown.

3. The console will automatically start AP mode.

USB cable

NOTE:

If no display appears on the LCD after you plug the adaptor, press [ RESET ] key by using a

pointed object.

TABLE STAND INSTALLATION

The unit is designed for

desktop or wall mount for easy

viewing. Follow the steps to

hook the table stand on the

botton of the console.

Step 1 Step 2

9

SET LCD DISPLAY VIEWING ANGLE

Press [ ] or [ ] key in normal mode to adjust LCD viewing angle to t table stand or wall

mount situation.

PAIRING WIRELESS 5-IN-1 WEATHER SENSOR & CONSOLE

After insert of batteries, the console will automatically search and connect the wireless 5-IN-1

sensor (the sensor antenna icon blinking).

Once the connection is successful, antenna icon and readings for outdoor temperature &

humidity, wind speed, wind direction and rainfall will appear on the LCD.

CHANGING BATTERIES AND MANUAL PAIRING OF SENSOR

Whenever you changed the batteries of the wireless 5-IN-1 sensor, pairing must be done

manually.

1. Change all the batteries to new ones in the sensor.

2. Press [ SENSOR / WI-FI ] key on the console.

3. Press [ RESET ] key on the wireless 5-IN-1 sensor.

PAIRING ADDITIONAL WIRELESS SENSOR(S) & CONSOLE (OPTIONAL)

This console can support up to 7 additional wireless sensor(s). You can press [SENSOR /

WIFI ] key to search the on display channel's sensor manually. Once your sensor paired up, the

sensor signal strength indicator and weather reading will appear on your console display.

NOTE:

- The additional wireless sensor(s) is not included.

- This console can support dierent type of additional wireless sensor, e.g. soil moisture and

pool sensor. Check with your retailer for more detail.

CREATE WEATHER SERVER ACCOUNT & SETUP WI-FI CONNECTION

The console can upload weather data to WUnderground and / or Weathercloud through WI-FI

router. You can follow the step below to setup your device.

NOTE:

The Weather Underground and Weathercloud website are subject to change.

CREATE WEATHER UNDERGROUND ACCOUNT

1. In https://www.wunderground.com click the "Join" on the top right corner to open the

registration page. Follow the instructions to create your account.

NOTE:

Use the valid email address to register your account.

2. After you have created your account and completed the Email validation, please go back to

the WUndergound web page to login. Then, click “My Prole” button on the top to open the

drop-down menu and click "My Weather Station".

10

3. In "My Weather Station" page bottom, press the "Add New Device" button to add your

device.

4. Follow their instruction to enter your station information, in the Step "Tell Us More About

Your Device", enter a Name for your weather station, then choose “Other” in “Device

Hardware” section. Fill in other the other information and select "I Accept" to accept

Weather underground's privacy terms, then click “Next” to create your station ID and key.

5. Jot down Your "Station ID" and "Station key" for the further setup step.

CREATE WEATHERCLOUD ACCOUNT

1. In https://weathercloud.net enter your information in "Join us today" section, then follow

the instructions to create your account.

11

NOTE:

Use the valid email address to register your account.

2. Sign in weathercloud and then you will go the "Devices" page, click "+ New" to create new

device.

3. Enter all the information in Create new device page, for the Model* selection box select

the "W100 Series" under "CCL" section. for the Link type* selection box select the "Pro

Weather Link", Once you have completed, click Create.

12

4. Write down your ID and key for the further setup step.

SETUP WI-FI CONNECTION

1. When you rst power up the console, or press and hold the [ SENSOR / WI-FI ]key for 6

seconds in normal mode, the console LCD will show "AP" and " " icon to signify that it has

entered AP (access point) mode, and is ready for WI-FI settings.

2. Use the smart phone, tablet, or computer to connect to the console through WI-FI.

3. In PC choose WiFi network settings or In Android / iOS choose setting

WI-FI to select the

console’s SSID: PWS-XXXXXX in the list and it will need several second to connect.

PWS-XXXXXX

PC WI-FI network interface Android WI-FI network interface

4. Once connected, enter the following IP address into your internet browser’s address bar, to

access the console’s web interface:

http://192.168.1.1

13

NOTE :

- Some browsers will treat 192.168.1.1 as a search, so make sure you include http:// header.

- Recommended browsers, such as the latest version of Chrome, Safari, Edge, Firefox or

Opera.

SETUP THE WEATHER SERVER CONNECTION

Enter the following information into the below web interface "SETUP" page. If you choose not

to use Wunderground.com or Weathercloud.net, leave the check boxes unchecked.

Function firmware version: 1.00

WiFi firmware version: 1.00

nist.time.gov

Server URL:

Time server setup

WiFi Router setup

SETUP ADVANCED

Wunderground

Station ID:

WDw124

******

IPACIR23Wc

Weather server setup

Station key:

Router:

Add Router

Search

Security type:

Router Password:

WAP2

ROUTER_A

Apply

Language: English

Weathercloud

Station ID:

Station key:

Mac address 00:0E:C6:00:07:10

Press to search router

Select the Wi-fi router (SSID) you will connect to

Manually enter the SSID if not on the list

Select router’s security type (usually WAP2)

Check to confirm upload to Weather underground

Enter new Station ID and Station key

assigned by W

undeground

Check to confirm upload to Weathercloud

Select time server

Press to complete the setting

SETUP page

Router’s password (leave blank if unsecured)

Press to allow add

router manually

Password record remark

(If you entered password)

Current ID and key recorded

(if any)

Current ID and key recorded

(if any)

Enter new Station ID and Station key

assigned by Weathercloud

Press “SETUP” icon

to SETUP page

NOTE:

- When WI-FI setup is complete, your PC or mobile will resume your default WI-FI connection.

- During AP mode, you can press and hold the [ SENSOR / WI-FI ] key for 6 seconds to stop

AP mode and the console will restore your previous setting.

WI-FI CONNECTION STATUS

Below is the WI-FI icon status on the console LCD:

Stable: Console is in

connection with WI-FI router

Flashing: Console is trying to

connect to WI-FI router

Flashing: Console currently in

Access Point (AP) mode

TIME SERVER CONNECTION STATUS

After the console has connected to the internet, it will attempt to connect to the internet time

server to obtain the UTC time. Once the connection succeeds and the console's time has been

updated, the “

” icon will appear on the LCD.

14

Time zone: To display the time of your time-zone, change the time zone in CLOCK setting

mode from '00' (default) to your time zone (e.g.08 for Hong Kong).

1. Press and hold [ CLOCK SET ] key for 2s to enter time setting mode.

2. Press [

] or [ ] key to enter your time zone, then press and hold [ CLOCK SET ] key to

conrm and exit. Please refer to MANUAL CLOCK SETTING session of manual for details of

other setting for the console.

The time will automatically synchronize Internet time server at 12:00AM and 12:00PM per day.

Also you can press the [REFRESH ] key to get the internet time manually within 1 minute.

ADVANCE SETTING IN WEB INTERFACE

Press "ADVANCED" key at the top of web interface to enter the advance setting page, this

page allow you to set and view the calibration data of the console, also you can update the

rmware in here (Only available in PC platform).

-560~ 560hpa / -16.54 ~ 16.54inHg / -420 ~ 420mmHg

Setting Range:

SETUP ADVANCED

Language: English

Temperature

o

C

Outdoor

Indoor

CH 1

CH 2

CH 3

CH 4

CH 5

CH 6

CH 7

Humidity %

Relative Pressure Offset:

Absolute Pressure Offset:

hpa

Range: -20 ~ 20

(Default: 0.0)

Current offset: 10Current offset: -9

Current offset: -5Current offset: 2

Current offset: -2Current offset: 3

Current offset: -2Current offset: 1.2

Current offset: -5Current offset: -0.2

Current offset: -3Current offset: -20.1

Current offset: -10Current offset: 11.5

Current offset: -3

(Default: 0)

Current offset: 10

(Default: 0)

Current offset: 0.2

Current offset: -5Current offset: 1

Pressure

Range: -20.0 ~ 20.0

o

C

-36.0 ~ 36.0

o

F (Default: 0.0)

**UV gain:

Range: 0.01 ~ 10(Default: 1.00)

Current gain: 1.1

**Light gain:

Range: 0.01 ~ 10(Default: 1.00)

Current gain: 1.0

** Depend on the model

**Wind speed gain:

**Wind direction:

**Rain gain:

Range: 0.5 ~ 1.5(Default: 1.00)

Range: -10 ~ 10(Default: 0

o

)

Range: 0.5 ~ 1.5(Default: 1.00)

Current gain: 0.85

Current offset: 2

o

Current gain: 0.75

Function firmware version: 1.00

WiFi firmware version: 1.00

Advancd page

Temperature

calibration section

Pressure

calibration section

Wind

calibration section

Press “ADVANCED” icon

to advancd page

Select setting unit

Humidity

calibration section

Rain

calibration section

CALIBRATION

1. User may enter or change the oset and gain values for dierent measurement parameters

while current oset and gain values are shown next to their corresponding boxes.

2. Once completed, press

Apply

in the SETUP page

The current oset value will show the previous value that you entered, if you want to change,

just input the new value in the blank, the new value will valid once you press

Apply

icon in

SETUP page.

NOTE:

Calibration of most parameter is not required, with the exception of Relative Pressure, which

must be calibrated to sea-level to account for altitude eects.

15

VIEW YOUR WEATHER DATA IN WUNDERGROUND

To view your weather station live data in a web browser (PC or mobile version), please visit

http://www.wunderground.com, and then enter your “Station ID” in the searching box. Your

weather data will show up on the next page. You can also login your account to view and

download the recorded data of your weather station.

Another way to view your station is use the web browser URL bar, type below in the URL bar:

https://www.wunderground.com/dashboard/pws/XXXX

Then replace the XXXX by your Weather underground station ID to go to your station live view

directly.

You can also use the Apple ipad's "WunderStation" app to

login your own weather station to view the live data.

WunderStation

VIEWING YOUR WEATHER DATA IN WEATHERCLOUD

1. To view your weather station live data in a web browser (PC or mobile version), please visit

https://weathercloud.net and sign in your own account.

2. Click the

icon inside the pull down menu of your station.

3. Click "Current", "Wind", "Evolution" or "Inside" icon to view the live data of your weather

station.

FIRMWARE UPDATE

The console supports OTA rmware update capability. Its rmware may be updated over the

air anytime (whenever necessary) through any web-browser on a PC with WI-FI connectivity.

Update function, however, is not available through mobile/smart devices.

Two types of rmware updates are available, namely Function Firmware and System WI-FI

Firmware, and are located at the bottom of ADVANCED page.

16

Current Function

firmware version

Current WI-FI

firmware version

FIRMWARE UPDATE STEPS

1. Download the latest rmware version (function or WI-FI) to your PC.

2. Set the Console into AP (access point) mode then connect the PC to the console (ref to

"SETUP WI-FI CONNECTION" section in previous page).

3. To update the Function rmware, click the

Browse

in Function rmware section and

browse to the location of the le you download in step 1. To update the WI-FI rmware, click

the

Browse

in WI-FI rmware section.

4. Click the corresponding

Upload

to start

transfer the rmware le to console (indicated by

a transfer completion %).

Upload

30% ...

BrowseC:\download\PWS_SYS.bin

Upload

Browse

Function firmware version: 1.00

WiFi firmware version: 1.00

3

4

5. Once the console received the rmware le, it

executes the update automatically as indicated

by the update progress on display (i.e. 100 is

completion).

6. The console will restart once the update completed.

NOTE:

- Function and WI-FI rmware cannot be updated at the same time, you need to update one by

one.

- Please keep connecting the power during the rmware update process.

- Please make sure your PC's WI-FI connection is stable.

- When the update process starts, do not operate the PC and console.

- During rmware update the console will stop upload data. It will reconnect to your WI-FI router

and upload the data again once the update success. If the console cannot connect to your

router, please end the SETUP page to setup again.

- After the rmware updates, user might need to input the Weather Underground ID and

password again.

OTHER SETTING & FUNCTIONS OF THE CONSOLE

MANUAL CLOCK SETTING

This console is designed to obtain the local time by synchronize with the assigned internet time

server. If you want to use it oine, you can set the time and date manually. During the rst time

startup, press and hold the [ SENSOR / WI-FI ]key for 6 seconds and let the console back to

normal mode.

1. In normal mode, press and hold [ CLOCK SET ] key for 2 seconds to enter setting.

17

2. The setting sequence: Time Zone DST ON/OFF Hour Minute 12/24 hour

format Year Month Day M-D/D-M format Time sync ON/OFF weekday

Language.

3. Press [

] or [ ] key to change the value. Press and hold the key for quick-adjust.

4. Press [ CLOCK SET ] key to save and exit the setting mode, or the unit will automatically

exit the setting mode 60 seconds later without pressing any key.

NOTE:

- In normal mode, press [ CLOCK SET ] key to switch between year and date display.

- During the setting, you can press and hold [ CLOCK SET ] key for 2 seconds to back to

normal model.

MOON PHASE

The moon phase is determined by

the time, date and time zone. The

following table explains the moon

phase icons of the Northern and

Southern hemispheres. Please refer

to ORIENTING THE 5-IN-1 SENSOR

TOWARDS SOUTH section about

how to setup for the Southern

hemispheres.

Northern

hemisphere

Moon Phase

Southern

hemisphere

New Moon

Waxing Crescent

First quarter

Waxing Gibbous

Full Moon

Waning Gibbous

Third quarter

Waning Crescent

POINTING THE WIRELESS 5-IN-1 SENSOR TO SOUTH

The outdoor 5-IN-1 sensor is calibrated to point to North for the maximum accuracy. However,

for the user's convenience (e.g. users in the Southern hemisphere), it is possible to use the

sensor with the wind vane pointing to South.

1. Install the 5-IN-1 wireless sensor with its wind meter end pointing to South. (Please refer to

INSTALLATION OF THE WIRELESS SENSOR for mounting details)

2. In normal mode of the console, press and hold [ INDEX ] key for 10 seconds to enter into

the calibration mode, then press [ INDEX ] key again until the “N” icon appears on the left

botton corner of the LCD to enter into the sensor orientation mode.

3. Use [

] or [ ] key to change to lower part (Southern Hemisphere).

4. Press [ INDEX ] key to conrm and exit.

NOTE:

Changing the hemisphere setting will automatically switch the direction of the moon phase on

the display.

18

SETTING ALARM TIME

1. In normal time mode, press and hold [ ALARM ] key for 2 seconds until the alarm hour digit

ashes to enter alarm time setting mode.

2. Press [

] or [ ] key to change the value. Press and hold the key for quick-adjust.

3. Press [ ALARM ] key again to step the setting value to Minute with the Minute digit ashing.

4. Press [

] or [ ] key to adjust the value of the ashing digit.

5. Press [ ALARM ] key to save and exit the setting.

NOTE:

- In alarm mode, the “

” icon will display on the LCD.

- The alarm function will turn on automatically once you set the alarm time.

ACTIVATING ALARM AND TEMPERATURE PRE-ALARM FUNCTION

1. In normal mode, press [ ALARM ] key to show the alarm time for 5 seconds.

2. When the alarm time displays, press [ ALARM ] key again to activate the alarm function. Or

press [ ALARM ] key twice to activate the alarm with ice pre-alarm function.

Alarm o Alarm on Alarm with ice-alert

NOTE:

Once the ice pre-alert activates, the pre-set alarm will sound and ice-alert icon will ash 30

minutes earlier if the outdoor temperature is below -3°C.

When clock reach the alarm time, alarm sound will start.

Where it can be stopped by following operation:

- Auto-stop after 2 minutes alarming if without any operation and the alarm will activate again in

the next day.

- By pressing [ALARM/SNOOZE] key to enter snooze that the alarm will sound again after 5

minutes.

- By pressing and hold [ALARM/SNOOZE] key for 2 seconds to stop the alarm and will activate

again in the next day

- By pressing [ ALARM ] key to stop the alarm and the alarm will activate again in the next day.

NOTE:

- The snooze could be used continuously in 24 hours.

- During the snooze, the alarm icon “

” will keep ashing.

TEMPERATURE / HUMIDITY FUNCTION & TREND

Use the [ °C / °F ] slide switch to select the temperature display unit. The temperature /

humidity trend indicator shows the trends of changes in the forthcoming few minutes.

Arrow indicator

Temperature / Humidity trend Rising Steady Falling

NOTE:

- When indoor temperature is below -40°C, the LCD will display “Lo”. If temperature is above

70°C, LCD will display “HI”.

- When outdoor temperature is below -40°C, the LCD will display “Lo”. If temperature is above

80°C, LCD will display “HI”.

- When humidity is below 1%, LCD will display “Lo”. If humidity is above 99%, LCD will display

“HI”.

19

COMFORT INDICATION

The comfort indication is a pictorial indication based on indoor air temperature and humidity in

an attempt to determine comfort level.

Too cold Comfortable Too hot

NOTE:

- Comfort indication can vary under the same temperature, depending on the humidity.

- There is no comfort indication when temperature is below 0°C (32°F) or over 60°C (140°F).

WIRELESS SENSOR SIGNAL RECEIVING

1. The console display signal strength for the wireless 5-IN-1 sensor, as per table below:

No signal Weak signal Good signal

2. If the signal has discontinued and does not recover within 15 minutes, the signal icon will

disappear. The temperature and humidity will display “Er” for the corresponding channel.

3. If the signal does not recover within 48 hours, the “Er” display will become permanent. You

need to replace the batteries and then press [ SENSOR / WI-FI] key to pair up the sensor

again.

VIEW OTHER CHANNELS (OPTIONAL FEATURE WITH EXTRA SENSORS)

This console is capable to pair with a wireless 5-IN-1 sensor and up to 7 wireless thermal-hygro

sensors. If you have 2 or more sensors, you can press [ CHANNEL ] key to switch between

dierent wireless channels in normal mode, or press and hold [ CHANNEL ] key for 2 seconds

to toggle auto-cycle mode to display the connected channels at 4 seconds interval.

During auto-cycle mode, press [ CHANNEL ] key to stop auto cycle and display the current

channel.

WIND

WIND SPEED AND DIRECTION SECTION OVERVIEW

Past wind

directions indicator

of last 5 minutes

Real time wind

direction indicator

Average / gust

wind speed

TO SET THE WIND SPEED UNIT AND DIRECTION DISPLAY FORMAT

1. In normal mode, press and hold [ WIND ] key for 2 seconds to enter into wind speed unit

mode and the unit will ash. Press [

] or [ ] key to change the wind speed unit in this

sequence: m/s

km/h knots mph

2. Press [ WIND ] key again to return to normal mode.

20

TO SELECT THE WIND DISPLAY MODE

In normal mode, press [ WIND ] key to switch between AVERAGE and GUST wind speed.

WEATHER INDEX

At the WEATHER INDEX section, you can press [ INDEX ] key to view the weather index in this

sequence: FEELS LIKE HEAT INDEX WIND CHILL DEWPOINT.

FEELS LIKE

The feels like temperature index determine how the outdoor temperature that people actually

feel.

HEAT INDEX

The heat index, which is determined by the wireless 5-IN-1 sensor's temperature & humidity

data, when the temperature is between 27°C (80°F) and 50°C (120°F).

Heat Index range Warning Explanation

27°C to 32°C (80°F to 90°F) Caution Possibility of heat exhaustion

33°C to 40°C (91°F to 105°F) Extreme Caution Possibility of heat dehydration

41°C to 54°C (106°F to 129°F) Danger Heat exhaustion likely

≥55°C (≥130°F) Extreme Danger Strong risk of dehydration / sun stroke

WIND CHILL

A combination of the wireless 5-IN-1 sensor's temperature and wind speed data determines the

current wind chill factor.

DEW POINT

- The dew point is the temperature below which the water vapor in air at constant barometric

pressure condenses into liquid water at the same rate at which it evaporates. The condensed

water is called dew when it forms on a solid surface.

- The dew point temperature is determined by the temperature & humidity data from wireless

5-IN-1 sensor.

WEATHER FORECAST

The built-in barometer can notice atmosphere pressure changes. Based on the data collected,

it can predict the weather conditions in the forthcoming 12~24 hours within a 30~50km (19~31

miles) radius.

Sunny Partly cloudy Cloudy Rainy Rainy / Stormy Snowy

NOTE:

- The accuracy of a general pressure-based weather forecast is about 70% to 75%.

- The weather forecast is reecting the weather situation for next 12~24 hours, it may not

necessarily reect the current situation.

- The SNOWY weather forecast is not based on the atmospheric pressure, but based on the

temperature of outdoor. When the temperature is below -3°C (26°F), the SNOWY weather

icon will be displayed on the LCD.

La page charge ...

Explore Scientific Professional WIFI colour Weather Center 5-in-1 V Le manuel du propriétaire

Ce manuel convient également à

Explore Scientific Professional WIFI colour Weather Center 5-in-1 V Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents