Planar PLL1911M Manuel utilisateur

Marque: Planar

Modèle: PLL1911M

Taper: Manuel utilisateur

www.planar.com

USER'S GUIDE

LED LCD Monitor

PLL1911M

Content

Operation Instructions...................................................................................................................................................1

Safety Precautions...........................................................................................................................................................3

First Setup...........................................................................................................................................................................5

Front View of the Product.............................................................................................................................................7

Rear View of the Product...............................................................................................................................................8

Quick Installation .............................................................................................................................................................9

Basic Operation.............................................................................................................................................................. 10

Advanced Operation—OSD Menu......................................................................................................................... 12

Supporting Timing Modes ........................................................................................................................................ 15

Technical Information ................................................................................................................................................. 16

Wall-mount instruction............................................................................................................................................... 17

Care and Maintenance................................................................................................................................................ 18

Troubleshooting............................................................................................................................................................ 18

Planar Support............................................................................................................................................................... 19

Operation Instructions

Thank you for purchasing this edge-lit LED LCD monitor, a high-resolution multi-scan color LED

LCD monitor.Please read this guide thoroughly before installation.

FCC RADIO FREQUENCY INTERFERENCE STATEMENT

WARNING: (FOR FCC CERTIFIED MODELS)

This

LED LCD monitor

has been tested and found compliant with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide proper

protection against harmful interference to a residential installation. This

LED LCD monitor

generates, uses, and can radiate radio frequency energy. Harmful interference to radio

communication may be led as a result if it‘s not properly installed and used. However, there is no

guarantee that interference will not occur in a particular installation. If this

LED LCD monitor

does cause serious interference to radio or television reception, resetting the

LED LCD monitor

may determine it. Moreover, users are encouraged to correct interference by doing one or more

of the following:

 Reorient or relocate the receiving antenna.

 Move the

LED LCD monitor

and the receiver further away from each other.

 Connect the

LED LCD monitor

into an outlet on a circuit different from that to which the

receiver is connected.

 Consult your local dealer or an qualified technician.

FCC Warning:

To assure a continued FCC compliance, a user must use a grounded power supply cord and the

provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized

changes or modifications to this

LED LCD monitor

would void the user‘s authority to operate this

device.

Note: If necessary, shielded interface cables and AC power cord must be used to meet the

emission level limits.

COMMUNIQUE D’AVERTISSEMENT DE LA FCC CONCERNANT LES INTERFERENCE DE

FREQUENCE RADIO: (SEULEMENT POUR MODELES CERTIFIE PAR LA FCC)

Ce moniteur a été testé et à été trouvé conforme aux limites pour un appareil numérique de

Classe B, suivant la partie 15 des règlements de la FCC. Ces limites ont été développées pour

offrir une protection satisfaisante contre les interférences nuisibles dans une installation

résidentielle. Ce moniteur génère, utilise et peut radier de l’énergie de fréquence radio. Ceci

peut causer des interférences nuisibles à des communication radio si l’appareil n’est pas

convenablement installé et utilisé. Il n’y à néanmoins aucune garantie que des interférences

n’apparaîtront pas dans une installation particulière. Si ce moniteur cause de sérieuses

interférences à la réception de signaux radios ou télévisées, une possibilité est de réinitialiser le

moniteur. Les usagers sont aussi encouragés à corriger les interférences en appliquant une ou

plusieurs des démarches suivantes:

 Réorientez ou déplacez l’antenne de réception.

 Placez le moniteur et le récepteur plus loin l’un de l’autre.

 Connectez le moniteur à une prise différente de celle à laquelle le récepteur est connecté.

 Consultez votre revendeur local ou un technicien qualifié.

Avertissement de la FCC:

Pour assurez une conformité continue au règlements de la FCC, l’utilisateur doit utiliser un

cordon d’alimentation mis à terre et le câble d’interface vidéo protégé avec noyaux en ferrite,

fourni avec l’appareil. Chaque modification ou changement non-autorisé appliqué à ce moniteur

peut faire perdre à l’utilisateur sont droit d’opération de cet appareil.

Note: Si nécessaire, des câbles d’interface protégés et un cordon d’alimentation alternante

doivent être utilisé pour être conforme aux limites d’émission.

According to WEEE regulation, this LED LCD monitor can't be handled as normal trash in Europe

when it is out of usage. Please refer to the recycle information from our website to handle it.

Safety Precautions

This

LED LCD monitor

is manufactured and tested on a ground principle that a user’s safety

comes first. However, improper use or installation may result danger to the LED LCD monitor as

well as to the user. Carefully go over the following WARNINGS before installation and keep this

guide handy.

WARNINGS:

 This LED LCD monitor should be operated only at the correct power sources indicated on

the label on the rear end of the LED LCD monitor. If you’re unsure of the power supply in

your residence, consult your local dealer or power company.

 Do not try to repair the LED LCD monitor yourself as it contains no user-serviceable parts.

The LED LCD monitor should only be repaired by a qualified technician.

 Do not remove the LED LCD monitor cabinet. There is high-voltage parts inside that may

cause electric shock to human bodies, even when the power cord is disconnected .

 Stop using the LED LCD monitor if the cabinet is damaged. Have it checked by a service

technician.

 Put your LED LCD monitor only in a clean, dry environment. Unplug the LED LCD monitor

immediately if gets wet and consult your service technician.

 Always unplug the LED LCD monitor before cleaning it. Clean the cabinet with a clean, dry

cloth. Apply non-ammonia based cleaner onto the cloth, not directly onto the glass screen.

 Keep the LED LCD monitor away from magnetic objects, motors, TV sets, and transformer.

 Do not place heavy objects on the cable or power cord.



For pluggable equipment, the socket-outlet shall be installed near the equipment and shall

be easily accessible.



Due to safety concerns, if the VESA mounting kit is purchased separately please make sure

the mounting kit is UL-Listed, and replaceable only by service personnel.



Do not operate the

product over 16 hours per day.

AVERTISSEMENTS :

 Ce moniteur doit être utilisé uniquement avec les sources d’alimentation adéquates

indiquées sur l’étiquette située au dos du moniteur. Si vous n’êtes pas sûr de l’alimentation

dans votre résidence, appelez votre vendeur local ou la compagnie d’électricité.

 N’essayez pas de réparer vous-même le moniteur car il ne contient pas de pièces réparables

par l’utilisateur. Le moniteur doit être réparé uniquement par un technicien qualié.

 Ne retirez pas le boîtier du moniteur. Il contient des pièces comportant un voltage élevé, qui

pourraient provoquer des électrocutions, même quand le cordon d’alimentation est

débranché.

 Arrêtez d’utiliser le moniteur si le boîtier est endommagé. Faites-le vérier par un technicien

qualié.

 Placez votre moniteur uniquement dans un environnement propre et sec. Débranchez

immédiatement le moniteur s’il était mouillé et faites appel à votre réparateur.

 Débranchez toujours

le moniteur avant de le nettoyer. Nettoyez le boîtier avec un chion

propre et sec. Appliquez un nettoyant sans ammoniaque sur le chion, mais pas

directement sur le verre de l’écran.

 Maintenez le moniteur éloigné des objets magnétiques, moteurs, postes de TV, et

transformateurs.

 Ne placez pas d'objets lourds sur le câble ou le cordon d'alimentation.

 Pour les ÉQUIPEMENTS BRANCHÉS PAR CÂBLE, la prise de courant doit être installée près de

l’équipement et doit être facilement accessible.

 Pour des raisons de sécurité, si vous achetez séparément le kit de xation VESA, assurez-vous

que celui-ci est certié UL, et qu’il peut être remplacé uniquement par un technicien qualié.

First Setup

Congratulations on your purchase of this high performance LED edge lit, LCD monitor.

This LED LCD monitor comes with the following accessories :

 LED LCD monitor  Power Cable

 User’s Guide  Audio Cable

 VGA Cable  DVI Cable

Installing the Stand Base

1. Turn the monitor over and set it upside down.

2. Align the monitor to the slots on the stand.

3. Turn the screw clockwise to attach the base to the monitor.

4. Check the underside of the stand to ensure that the monitor has been firmly installed to the

stand and that the screws do not loosen.

Monitor Adjustment

The LED LCD Monitor is designed to have a tilt range of -5

to 19

, a swivel range of -30

to 30

and a height adjustment of 4.3” (110mm).

Disconnecting the Stand Base

1. Turn the monitor over and set it upside down.

2. Turn

the screw counterclockwise to l

oosen it.

3. Deta

ch the stand from the monito

Front View of the Product

 OSD Menu On/Off

 Volume Adjust/Scroll Down/Adjust Decrease

 Preset Mode/Scroll Up/ Adjust Increase

 Confirm Select/ Auto adjust

 Power ON/OFF

 LED Indicator

    

Rear View of the Product

 Power input (AC input)

 Audio Input

 DVI input (DVI 24 pin)

 VGA input (D-Sub 15 pin)

   

Quick Installation

1. Connect either VGA or DVI Video Source from the monitor to the computer. Make sure both

monitor and computer are powered OFF.

2. Connect the audio cable from audio output of computer to the audio input of the monitor.

3. Connect the power cord to a properly grounded AC outlet, then to the monitor.

Power-ON computer and then POWER-ON the monitor.

Set the timing mode on your computer. Recommended resolution and refresh rate is

1280X1024 @ 60 Hz.

Example:

Power c

able

VGA cable

udio cable

DVI cable

Basic Operation

Before using the LED LCD monitor:

Connect external equipments properly.

Insert the power plug, and the power LED indicator will light orange.

Power On/Off

To turn the LED LCD monitor on/off:

Press POWER button on the front of LED LCD monitor. The power LED indicator lights green

when the LED LCD monitor is on.

Using the OSD Menu

You are able to use OSD menus to adjust various settings by using menu button on the front of

the LED LCD monitor.

Display main menu

Exit from OSD menu

Selects between VGA, DVI or Auto mode / Press the button for three

seconds to auto adjust the image (VGA only)

Confirm the selection

Select the desired item when in OSD menu

▼

When not in OSD menu, directly enters Audio Adjust.

Select the desired item when in OSD menu

▲

When not in OSD menu, directly enters Preset Mode

▼ + ▲ Recall both of Contrast and Brightness (when not in OSD menu)

OSD Lock Out Function

When

LED LCD monitor

is in normal display, you can enable the “OSD Lock Out” function.

Option 1: OSD lock – all 4 buttons are locked except the “POWER” button.

Press and hold the 1 button and the ▲ button for 3 seconds to lock the OSD buttons.

The

LED LCD monitor

will show an “OSD Lock Out” message for 5~10 seconds and the message

will disappear automatically.

Repeat this step to unlock.

Option 2: OSD & Power button lock – all 5 buttons including the “POWER” button are locked.

Press and hold the 1 button and the ▼ button for 3 seconds to lock all 5 buttons.

The

LED LCD monitor

will show an “Lock Out” message for 5~10 seconds and the message will

disappear automatically.

Repeat this step to unlock.

Advanced Operation—OSD Menu

You can use the OSD menu to adjust various settings for your

LED LCD monitor

Press the 1 button to display the OSD Menu, and use ▲▼ to select the desired OSD menu.

Short Cuts Function from the button(s)

Auto Image Adjust: To auto adjust Horizontal Position, Vertical Position, Phase (Fine

Tune) and Clock (H. Size) of the screen.

Contrast: To adjust the foreground white level of screen image.

▲: increase contrast, ▼: decrease contrast.

Brightness: To adjust the luminance of the video.

▲: increase brightness, ▼: decrease brightness.

ECO : Allows the user to turn the ECO On or Off. Contrast and Brightness adjustment

disabled when ECO is active.

Input Select: To select input source, VGA, DVI, or Auto.

Audio Adjust: To adjust the audio functions.

Volume: To adjust the volume of speaker output.

Mute: To turn the Mute ON/OFF.

Color Adjust: To select the color for improving brightness and color saturation

between 9300K, 6500K, 5400K,and User Color.

9300K: Adds blue to screen image for cooler white.

6500K: Adds red to screen image for warmer white and richer red.

5400K: Adds green to screen image for a darker color.

User Color: Individual adjustments for red (R), green (G), blue (B).

1. Press button 2 to select the desired color.

2. Press ▼ or ▲ button to adjust selected color.

Information: To display the information, regarding the current input signal coming

from the graphic card in your computer.

Note: See your graphic card user guide for more information about changing the

resolution and refresh rate.

Manual Image Adjust: To manually adjust the Horizontal Size, H. /V. position, Fine Tune,

Sharpness and Preset Mode.

Horizontal Size: To adjust the width of the screen image.

▼: decrease the width of screen image, ▲: increase the width of screen image.

H./V. Position: To adjust the horizontal and vertical position of the video.

H. Position: ▲: move screen to the right, ▼: move screen to the left.

V. Position: ▲: move screen up, ▼: move screen down.

Fine Tune: To adjust the delay time of data and clock.

Press ▼ or ▲ to adjust to your preference.

Sharpness: To adjust the clarity of a non-SXGA (1280x1024) signal with ▼ or ▲ button.

Preset Mode: Provides an optimum display environment depending on the contents

displayed. It contains 5 user-selectable presets.

Standard is for general windows environment and monitor default setting.

Game optimized for PC game environment.

Cinema optimized for movie and video environment.

Scenery optimized for displaying outdoor scenery images.

Text optimized for text editing and viewing in a word processing environment.

Setup Menu: To set up Language Select, OSD Position, OSD Time Out and OSD

Background.

Language Select: To allow users to choose from available languages.

OSD Position: Press ▼ or ▲ button to select between horizontal and vertical OSD

Position adjustment.

H. Position: To horizontally adjust the OSD position.

▲: move OSD to the right, ▼: move OSD to the left.

V. Position: To vertically adjust the OSD position.

▲: move OSD up, ▼: move OSD down.

OSD Time Out: To automatically turn off On Screen Display (OSD) after a preset period

of time.

OSD Background: Allows the user to turn the OSD background On or Off.

Memory Recall: To recall factory settings for Video & Audio controls.

Press button 2 to select the Memory Recall menu option.

Supporting Timing Modes

STANDARD RESOLUTION

VGA 720 x 400 @ 70Hz

VGA 640 x 480 @ 60Hz

MAC 640 x 480 @ 67Hz

VESA 640 x 480 @ 72Hz

VESA 640 x 480 @ 75Hz

VESA 800 x 600 @ 56Hz

VESA 800 x 600 @ 60Hz

VESA 800 x 600 @ 72Hz

VESA 800 x 600 @ 75Hz

MAC 832 x 624 @ 75Hz

VESA 1024 x 768 @ 60Hz

VESA 1024 x 768 @ 70Hz

VESA 1024 x 768 @ 75Hz

VESA 1152 x 864 @ 75Hz

VESA 1152 x 870 @ 75Hz

VESA 1280 x 960@ 60Hz

VESA 1280 x 1024 @ 60Hz

VESA 1280 x 1024 @ 75Hz

Note: DVI supports 480i, 480p, 576i, 576p, 720p.

Warning: Do not set the graphic card in your computer to exceed these maximum refresh rates.

Doing so may result in permanent damage to your monitor.

Avertissement : Ne réglez pas la carte graphique de votre ordinateur en dépassant ces taux de

rafraîchissement maximaux. Si vous le faites, cela va irrémédiablement détériorer votre moniteur.

Technical Information

Panel 19” TFT (with LED backlight)

Power Management On: 21 Watts (typical), 25 Watts (maximum)

Standby Mode: < 0.5 Watt

Displayable Resolution

SXGA 1280x1024 max.

Vertical Frequency 75Hz max.

Pixel Dimension 0.294 x 0.294 mm

Display Color 16.7M

Tilt -5°~ 19°

Active Display Area 376.32mm X 301.05mm

Temperature Operating: 0°C ~ + 40°C

Storage: -20°C ~ + 60°C

Compliance FCC, CE, UL, WEEE，

Power Input Voltage AC100-240 V

Speaker 1W x 2

Wall-mount instruction

Preparing To Install The Optional Wall Mount Arm (not included)

This LED LCD monitor can be attached to a wall mounting arm you can purchase separately.

Turn the power OFF then disconnect the cables from the LED LCD monitor before performing

the procedure below.

1. Disconnect all the cables and cords from the Monitor to prevent breakage.

2. Ca

refully place the Monitor face down on a soft and flat surface (blanket, foam, cloth, etc)

prevent any

damage to

the Monitor.

3. Remove the

screws so that the stand base can be

removed.

4. Gently

remove the stand

base.

Attaching The Optional Wall Mount Arm (not supplied)

Follow these steps to finish installing the wall mounting arm:

1. Place the wall mounting arm onto the back of the LED LCD

monitor. Line up the holes of the arm with the holes in the

back of the monitor.

2. Insert the 4 screws into the holes and tighten.

3. Reconnect the cables. Refer to the User’s Guide that came

with the optional wall mounting arm for instructions on

attaching it to the wall.

NOTE

 100mmx100mm VESA high hole (n=4), M4, pitc

h =0.7 mm

scr

ew mounting kit not included.

4mm, 0.7 pitch

threaded holes x 4

100mm x 100mm Screw

Mounting Options

Care and Maintenance

Care

 Avoid exposing your LED LCD monitor directly to sunlight or other heat source. Place your

LED LCD monitor away from the sun to reduce glare.

 Put your LED LCD monitor in a well ventilated area.

 Do not place any heavy things on top of your LED LCD monitor.

 Make certain your LED LCD monitor is installed in a clean and moisture-free area.

 Keep your LED LCD monitor away from magnets, motors, transformers, speakers, and TV sets.

Note



Move the LED out of the package and take o the plastic bag and Polystyrene Foam.



Pull the base from Parallel versus Panel to Vertical.



Adjust the Panel within -5 degree leaning forward and 19 degree leaning backward.

Safety Tips

 If smoke, abnormal noise or odor came out from your LED LCD monitor, caution you should

remove the power cord immediately and call your service center.

 Si de la fumée, un bruit anormal ou une odeur s'échappait de votre moniteur, débranchez

immédiatement le cordon d'alimentation et appelez votre centre de service.

 Never remove the rear cover of your LED LCD monitor cabinet. The display unit inside

contains high-voltage parts and may cause electric shock to human bodies.



Never try to repair your

LED LCD monitor

yourself. Always call your service center or a

qualied technician to x it.

Troubleshooting

No power



Make sure A/C power cord is securely connected to the power adapter and the power supply

is rmly connected to the

LED LCD monitor



Plug another electrical device into the power outlet to verify that the outlet is supplying

proper voltage.

 Make sure all signal cables are installed.

Power on but no screen image



Make sure the video cable supplied with the

LED LCD monitor

is tightly secured to the video

output port on back of the computer. If not, tightly secure it.

 A

djust brightness.

Wrong or abnormal colors



If any colors (red, green, blue) are missing, check the video cable to make sure it is securely

connected. Loose or broken pins in the cable connector could cause an improper connection.

 Connect the

LED LCD monitor

to another computer.

La page charge ...

Planar PLL1911M Manuel utilisateur

Marque: Planar

Modèle: PLL1911M

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Planar PLL1911M User manual

Planar PLL1911M Manuel utilisateur

Planar PLL1911M Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents