brondell RF-20 Le manuel du propriétaire

OWNER’S MANUAL

Circle Reverse Osmosis Water Filtration System

Model # RC100

1

– Please keep the User’s Manual where it can be readily reached or found –

PRODUCT INSTALLATION

07 FAUCET INSTALLATION

09 TVALVE INSTALLATION

10 USING QUICK CONNECTORS

11 DRAIN CLAMP INSTALLATION

13 FINISHING UP

14 PREPARING FOR USE

TECHNICAL INFO

28 SPANISH VERSION

57 FRENCH VERSION

GENERAL INFO

02 SAFETY INFORMATION

03 FEATURES

04 FILTRATION PROCESS

05 PRODUCT COMPONENTS

MAINTENANCE

15 FILTERS

Filters

Filter Change Indicator

Filter Replacement Cycle

16 FILTER REPLACEMENT

19 PREPARING FOR EXTENDED

NONUSE

20 TROUBLESHOOTING

21 PRODUCT SPECIFICATIONS

21 WATER FLOW DIAGRAM

22 PERFORMANCE DATA SHEET

25 WARRANTY

26 CONTACT BRONDELL

CONTENTS

2

SAFETY INFORMATION

CAUTION : If not observed, minor physical injury or property damage may occur as a result.

• For California Residents: CR2032 batteries contain Perchlorate Material - special handling may apply. Visit

http://www.dtsc.ca.gov/hazardouswaste/perchlorate for more information.

• Use or place the unit on a level area and do not apply force to the unit.

• Periodical lter replacement is prerequisite for getting clean water.

• When moving the product or replacing the Pre-Carbon Plus lter, there may be black residue particles

under the tank bottom and stored water may get contaminated.

• Do not use ltered water for the water exchange of an aquarium or a shbowl.

• The ltration system installation shall comply with state and local laws and regulations. Do not use with

water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after

the system.

• It is recommended to install the product under the sink.

• The minimum allowable inlet water pressure is 275kpa (40 psi). If the water pressure is less than 275kpa

(40 psi), it could result in noise or water shortage.

• The maximum allowable inlet water pressure is 827 kPa (120 psi).

• Only use attachments(accessories) recommended or sold by manufacturer.

• Do not use the product outside.

• Systems certied for cyst reduction may be used on disinfected waters that may contain lterable cysts.

• The reverse osmosis system contains a replaceable treatment component, critical for the eective

reduction of total dissolved solids, and product water shall be tested periodically to verify that the system

is performing properly. Replacement of the reverse osmosis component should be with one of identical

specications, as dened by the manufacturer, to endure the same eciency and contaminant reduction

performance.

Be careful to keep this safety information. Please read this information to

prevent property loss and ensure the safety.

DANGER : If not observed, serious injury or even death may occur as a result.

• Do not install the unit near heaters.

• Do not place dishes or containers of water, drugs, food, or small metal objects on top of the product.

• Do not put a candle, cigarette or any other ammable object on the product.

• Do not spray water or wipe the product with benzene when cleaning.

WARNING : If not observed, serious physical injury or property damage may occur as a result.

• Read all the instructions before using the Circle.

• To reduce the risk of injury, close supervision is necessary when a Circle is used near children.

• This Circle is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the Circle by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the Circle.

• This Circle can be used by children aged from 8 years and above.

• The new hose-sets supplied with the Circle are to be used and old hose-sets should not be reused.

3

No back pressure

Waste water

CARBON BLOCK

RO MEMBRANE

RO puriﬁed water

Tap

water

Tap water

WATER TANK

1

2

3

4

5

6

7

Outlet

TankInlet

Drain

Outlet

TankInlet

Drain

Outlet

TankInlet

Drain

Quick

1

/4 turn

5 Step Filtration

system

4. Space Saving Compact Design

With its unique integrated tank and rapid rell rates, the

Circle takes up minimal space under the sink, leaving more

room for storage.

5. Certied Four-Stage Filtration Technology

Four separate lters work together to deliver maximum

ltration ensuring clean healthy water for the family. WQA

Gold Seal certied for trusted performance.

6. Eco-Friendly High Capacity System

Unique design and patented technology delivers constant

ow rates and rapid rell improving overall eciency of the

system without the use of pumps or electricity.

7. Quick Change Filters

Filter replacement is a snap with our easy twist and seal

system. No tools needed, simply insert and twist a quarter

turn to change and seal.

3. Designer Faucet with Integrated LED Filter

Change Indicator

For ultimate convenience the Circle faucet includes an

automatic lter change indicator letting you know when

it’s time to change the lters.

2. RO Filter Auto Flushing

Automatically ushes the RO membrane signicantly

extending the life of the lter.

1. Water Saving Smart Technology

The intelligent “smart valve” and unique circular reservoir

eliminates backpressure (common in RO systems) reducing

waste water and making the Circle up to 10 times more

ecient than existing products.

FEATURES

1

2

3

4

7

4

Regulator

Drain

Dual-Layer

Reservoir

Auto Shut oﬀ

Valve

Check①

Check②

Tap

water

Faucet

Smart

Valve

D

T

SEDIMENT

PRE-CARBON PLUS

RO MEMBRANE

POST CARBON

Regulator

Stage One: Sediment Filter

The Sediment lter reduces particulate materials such as sand, rust, and ne particles from the water

supply. This rst stage also acts as a pre-lter protecting and extending the life of the following lters.

Stage Two: Pre-Carbon Plus Filter

This second stage lter signicantly reduces harmful VOCs , chlorine, and soluble contaminants

which can damage the RO Membrane lter.

Stage Three: RO Membrane Filter

The RO lter works by pushing water through a semi-permeable membrane thereby separating

H2O molecules from contaminants in tap water. The powerful RO Membrane signicantly reduces

pollutants such as: heavy metals, cysts, uoride, arsenic, industrial chemicals, and more.

Stage Four: Post Carbon Block Filter

As the nal stage in the ltration process, the Post Carbon Block lter further reduces any lingering

water contaminants such as chlorine and volatile organic compounds (VOCs), improving the overall

taste and odor of the dispensed water.

THE FOURSTAGE WATER FILTRATION PROCESS

FILTRATION PROCESS

The RC100 is tested and certied to NSF/ANSI 42, 53 and 58 for the reduction

of Aesthetic Chlorine, Taste and Odor, Cyst, VOCs, Fluoride, Pentavalent Arsenic,

Barium, Radium 226/228, Cadmium, Hexavalent Chromium, Trivalent Chromium,

Lead, Copper, Selenium and TDS as veried and substantiated by test data. The

RC100 conforms to NSF/ANSI 372 for low lead compliance.

See performance data sheet on page 22 for all certied claims

5

Cover

Post Carbon Block Filter

Water Tank

Sediment Filter

RO Membrane Filter

Pre-Carbon Plus Filter

PRODUCT COMPONENTS

Waste Water

Drain Clamp

Outlet to

Faucet

Water Supply

Inlet

6

PRODUCT COMPONENTS cont.

Drain Clamp

* Actual product may dier from images shown

ACCESSORIES

TOOLS NEEDED

Water Supply T-Valve

with Rubber Washer

(3/8” connection)

Owner’s Manual

T-Valve Adapters

with Rubber Washer 3/8” to 1/2”

Tubing

One (1) Inlet: 1/4” Tubing (Orange)

One (1) Drain: 1/4” Tubing (White)

LED Indicator Faucet

Assembly with

Attached Tubing (Blue)

Phillips Screwdriver

Adjustable Wrench

Safety Glasses

Drill & 1/4” Drill Bit

Towel & BucketThin Screwdriver, Straw,

or similar item less than

1/4” in diameter

Scissors for

cutting zip ties

Filter Change

Chart

7

PRODUCT INSTALLATION

STEP 1: FAUCET INSTALLATION

Before Installation

You will need an existing faucet hole at least 7/16

inches in diameter in the sink or countertop to install

the supplied ltered water faucet. You may also

replace an existing kitchen sprayer, soap dispenser,

or plug already on the countertop or sink.

1. Unpack the faucet and insert the Top Spout into the Main

Body by pushing down until inserted then screw the Top Cap

clockwise until secured in place.

2. Cut zip tie on the blue water connection tubing and unroll

to straighten tubing. Be careful not to cut the tube when

removing the zip tie.

If drilling a new hole is required for the

faucet installation, please consult a

professional. Brondell will not be liable for

any damages including those to the sink

or countertop due to installation of the

faucet or drilling a hole.

For California Residents: CR2032

batteries contain Perchlorate Material -

special handling may apply. Visit http://

www.dtsc.ca.gov/hazardouswaste/

perchlorate for more information.

Please nd answers to Frequently Asked

Questions (FAQs) and installation videos

on brondell.com

1

Locking Nut

Plastic Washer

Top Spout

Top Cap

Main Body

Lock Washer

Counter Top

1/4" Tube

(connected to faucet)

Escutcheon

LED Display

Battery Seat

(CR2032)

Battery

8

STEP 1: FAUCET INSTALLATION (cont.)

3. Attach the Escutcheon to the Main Body by inserting the blue

tubing through the Escutcheon and pushing it all the way up

until connected to the main body.

3

4. Install the faucet on top of the countertop or sink and feed

the blue tubing through the hole to the cabinet below. Then

slide the large Plastic Washer as shown up through the blue

tubing until snug against the bottom of the countertop or

sink hole. Be sure that the at part of the Plastic Washer is

facing up and the raised area is facing down, as shown here.

4

5

5. Install the “Lock Washer” and the “Locking Nut” the same way

and tighten until the plastic washer is holding the faucet

assembly rmly in place. The faucet is now installed!

6. Pull the plastic tab out from the battery compartment to

activate the faucet indicator. The LED light will blink red

once, blue once, and then will be ready to go.

PRODUCT INSTALLATION (cont.)

9

STEP 2: T-VALVE INSTALLATION

1. Turn o the cold water supply under the sink at the wall.

Then, turn on the cold water to drain the residual water

from the water lines.

2. Disconnect cold water supply line from the supply valve

under the sink at the wall.

3. Connect the bottom of the 3/8-inch T-valve to the cold water

supply valve at the wall. If the water connection is a 1/2-inch

size, use the provided adapters with rubber washers to

connect the T-valve to the supply line.

4. Re-connect faucet water supply hose to the top of the T-valve

as shown, then insert one end of the orange water supply

tubing into the T-valve 1/4-inch Quick Connector. Be sure to

push rmly into place to secure.

NOTE: See next page for tips on how to use Quick Connectors.

5. Make sure the T-valve is in the closed position (valve arm

should be facing up).

Install the T-valve on the cold water supply only.

Never connect to the hot water supply!

You may wish to place a bucket or container under

the pipes to catch any excess water.

4

5

1–2

10

PRODUCT INSTALLATION (cont.)

Visit brondell.com for our Quick Connect

video tutorial.

Tube connections on the T-Valve, Drain Clamp, Circle, and Indicator Faucet are all of the “Quick

Connect” variety. The steps below illustrate how to connect and disconnect the Tubes from these

connectors.

a. Push the Tube into the Collette. The Collette is a

collar that provides a secure t for the Tube and

prevents water leaks.

b. Push the Tube in until it stops. The Tube will

be secure, and resistant to tugs or pulls. The

Collette will be rigid and raised slightly from the

Connector Housing.

c. To disconnect the Tube, push down and hold the

Collette rst, and then pull the Tube out gently.

Connector

Housing

Tube

Collette

STEP 2A: USING QUICK CONNECTORS

11

MOUNT

DRAIN VALVE

HERE

1. If there is an existing drain connection for a 1/4-inch quick connect tube, then use this connection.

Otherwise, locate a suitable area on the sink drain pipe to install the provided drain clamp.

NOTE: Select a location for

the drain hole based on the

design of the plumbing. It

should be installed above the

trap and on the vertical or

horizontal tail piece. Locate

the drain connection away

from the garbage disposal.

See example to the right.

2. Once a suitable spot has been selected for the drain clamp,

drill a 1/4-inch hole into one side of the pipe. Be sure to

use a suitable drill bit for the material being drilled into (for

example: PVC versus Metal Pipe) and be sure to use safety

goggles.

NOTE: Starting with the 1/8-inch drill bit, drill a 1/8-inch hole

in the drain pipe. Use the 1/4-inch drill bit to enlarge the hole.

If you do not have a 1/8-inch drill bit, then you can just use

the 1/4-inch bit. Clean the debris from the pipe and the hole

before continuing.

STEP 3: DRAIN CLAMP INSTALLATION

WARNING: this step may require drilling into the existing drain pipe. Please seek

professional help when completing this step and always wear safety protection including

safety goggles!

DO NOT drill all the way through the pipe.

2

1

12

PRODUCT INSTALLATION (cont.)

3. Align the drain clamp to the hole

a. Take the front half of the drain saddle (with the 1/4-inch

quick connector opening) and unscrew the grey quick

connector from the saddle as shown in diagram 3a.

4. Once the drain clamp is secure and tight on the pipe,

remove the guide and screw the 1/4-inch Quick Connector

back into place.

5. Lastly, insert the white drain tube into the 1/4-inch Quick

Connector on the drain clamp and push rmly into place.

b. Insert a screwdriver, straw, or similar straight thin item into

the front of the rst half of the saddle (to use as a guide) as

shown here in diagram 3b.

c. Insert the end of the guide into the 1/4-inch hole in the

drain pipe and slide the clamp until secure against the

drain pipe. The hole is now properly lined up with the

drain clamp hole. Hold secure by keeping the guide

inserted until the clamp is secured by screwing on the

back side as shown in diagram 3c.

STEP 3: DRAIN CLAMP INSTALLATION (cont.)

3

a

3

b

3

c

4–5

13

1. Connect the tubes:

a. Connect the open end of the 1/4-inch blue tubing (from

faucet) to the top of the Circle by pushing into the middle

hole labeled “Outlet”.

b. Connect the open end of the white tubing (from the drain

clamp) to the top of the Circle by pushing into the hole

labeled “Drain”.

c. Finally, connect the open end of the orange tubing (from

the water supply T-valve) to the top of the Circle by

pushing into the hole labeled “Inlet”.

d. Be sure to push the ¼” tubing rmly into place to secure.

2. Turn on Water and Check for Leaks

a. Open the T-valve by turning the valve arm 90° and turn

cold water supply back on under the sink at the wall. The cold

water supply will then begin to supply water to the Circle.

b. After turning on the water supply, check all connections for

leaks. Wait 5 minutes and check once more for leaks before

proceeding to the next step.

Failure to properly install this product or to properly

check for leaks may cause damage to the property.

In these instances, Brondell, Inc. will not be held

responsible for any damages.

STEP 4: FINISHING UP

Inlet

Outlet

Drain

1

2

14

PREPARING FOR USE

T-VALVE

1/4” WATER

SUPPLY HOSE

(Orange hose)

1/4˝ FAUCET

CONNECTOR HOSE

(Blue hose)

1/4” DRAIN HOSE

(White hose)

DRAIN

CLAMP

HOT COLD

WATER

FILTRATION

DEVICE

(RC100)

FAUCET

INSTALLATION DIAGRAM

During the initial purging of the system, you will hear air clearing out of the system

through the faucet along with some spurts of water. This is NOT a malfunction and is

normal operation during the very rst use or when completing a lter change.

STEP 1: FLUSHING THE SYSTEM

1. Turn the provided faucet on all the way for 10 minutes to purge all the air out of the system. It is

normal for some water to ow out of the faucet during this rst purge.

2. After the initial 10 minute purge, turn the provided faucet o and let the system run for 40

minutes to allow the water tank to ll for the rst time.

3. After 40 minutes, turn the faucet on all the way once more for 10 minutes (or until the tank

empties) to ush the lters and the water tank.

4. Turn the faucet o.

5. The tank will ll again in approximately 40 minutes, and then ltered water will be ready to drink.

6. Record installation date on the lter change sticker chart and place sticker inside the front cover,

under the sink cabinet on the door, or another safe accessible place.

15

Part Number Filter Name Usable period

RF20

Sediment Filter 6 months

Pre-Carbon Plus Filter 6 months

Post Carbon Block Filter 6 months

RF-40 RO Membrane Filter 24 months

FILTERS

FILTER CHANGE INDICATOR

FILTER REPLACEMENT CYCLE

Contact Brondell at 888-542-3355, or visit us on the Web at www.brondell.com to order

replacement lters.

The lters are critical to the performance of the Circle Reverse Osmosis Water Filtration system, and

it is important to replace all of the lters on a regular basis. If any of the lters are overused beyond

the recommended service life, the performance of the water ltration device can deteriorate. Do not

miss the lter replacement cycle or use non-compatible lters as this can aect system performance

or damage the unit.

The LED lter change indicator in the faucet works by tracking both time and water ow from the

Circle RO system. When 6 months time or 475 gallons of water has been ltered through the system

(whichever comes rst), the LED will ash red when dispensing water instead of ashing blue.

When the faucet LED indicator begins to ash red, it’s now time to change the lters and reset the

faucet indicator by replacing the battery.

Note: a new battery is always included with the RF-20 lter replacement set.

FILTERS AND FILTER CHANGE INDICATOR

The lter replacement cycle may be increased for areas with poor water quality or

greater use.

The period for the lter exchange is based on an average production of 2.6

gallons of drinking water per day.

16

FILTER REPLACEMENT

HOW TO REPLACE THE FILTERS

4. Turn the lter(s) to be replaced a quarter-turn counter-

clockwise until the unlock arrow on the lter label lines up

with the arrow on lter base above it. Pull down to remove.

3. Remove the front cover from the Circle as shown.

Match this to the arrow on the lter base

2. Once the tank has drained, close the T-valve under the sink to

shut o the ow of water to the Circle.

Turn the faucet o.

1. Turn the Indicator faucet on all the way and keep it on until

the water tank is emptied completely. Keep the faucet on, in

order to release any leftover pressure in the system.

NOTE: Since this water is ltered water, you may want to

store it in a pitcher.

1

2

3

4

SEE DIAGRAM ON

FILTER HOUSING ABOVE

17

7. Replace the Front Cover.

PO Box 470085 San Francisco, CA 94147

brondell.com 888-542-3355

Made in Korea

month day year

6. After replacing lters, locate the lter change sticker chart and write down the date and lters

changed on the chart. It’s important to track each lter change since the RO lter is on a dierent

cycle than the other 3. Here’s the replacement cycle:

After 6 months: replace 3 lter set (RF-20) and replace faucet battery

After 12 months: replace 3 lter set (RF-20) and replace faucet battery

After 18 months: replace 3 lter set (RF-20) and replace faucet battery

After 24 months: replace 3 lter set (RF-20), the RO lter (RF-40), and replace faucet battery

Note: Brondell provides a new faucet battery replacement with each RF-20 lter set and a new

lter change sticker chart with each RF-40.

5. Install the new lter by aligning the arrow indicators on the

lter label (a) and lter base above (b) as shown. Push up.

Turn a quarter-turn counter-clockwise until the lter stops.

The lter base arrow should now point to the “lock” arrow

on the lter label. Repeat with any remaining lters to be

changed

Important: Be sure when replacing the lters that

you install the new ones in the correct location by

referring to the color coded sticker on the machine

and matching to the colored lter labels. Failure

to replace the lters in the correct location may

damage the machine and lters.

8. Open the T-valve under the sink to turn on the ow of water

to the Circle.

b

5

7

8

a

18

10. Replace the battery in the faucet LED indicator to reset the

lter change reminder. The battery type is CR2032 and

Brondell provides one with every set of RF-20 lters.

9. Flush the new lters and the system thoroughly with the

following steps.

a. Turn the provided faucet on all the way for 10 minutes to

purge all the air out of the system.

a. Under the faucet handle, locate the black rubber battery

compartment. Grasp it from the sides and pull down as

shown.

b. After the initial 10 minute purge, turn the provided faucet

o and let the system run for 40 minutes to allow the

water tank to ll.

b. Remove the old battery from the compartment by lifting

the silver metal tab and sliding the battery out of the

rubber casing. Wait 30 seconds for the residual energy to

drain to reset the indicator.

c. Turn the faucet on all the way once more for 10 minutes

(or until the tank empties) to ush the lters and the water

tank.

c. Replace with a new CR2032 battery by sliding the battery

under the silver tab, making sure that the words on the

battery are facing out. A fresh CR2032 battery comes with

every RF-20 Replacement Filter pack.

e. The tank will ll again in approximately 40 minutes, and

then ltered water is ready to drink.

d. Turn the faucet o.

d. Push the black rubber battery compartment back up into

the faucet handle.

9

10a

10c

10d

FILTER REPLACEMENT (cont.)

HOW TO REPLACE THE FILTERS (cont.)

La page charge ...

brondell RF-20 Le manuel du propriétaire

Ce manuel convient également à

brondell RF-20 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents