Prestige Platinum+ APS-750a Manuel utilisateur

Marque: Prestige

Modèle: Platinum+ APS-750a

Catégorie: Alarme de voiture

Taper: Manuel utilisateur

Ce manuel convient également à

Model APS 750a

Installation Manual

4 Channel Remote Car Starter

With Full Feature Alarm System

Installation Instructions

This Unit Is Intended For Installation In Vehicles With

12 Volt Negative Ground Electrical Systems,

Gasoline Engines, And Automatic Transmissions Only.

Kit Contents:

APS-750a Control Module

(2) - Three Button Anti Code Grabbing Transmitters

4 Channel Code Learning Receiver

On Board Extended Range Antenna

Six Tone Multi Tone Siren

(1) - Multi Pin Input/Output Harness

(1) - Six Pin Power Harness

(1) - Four Pin Auxiliary Output Harness

(1) - Two Pin LED Indicator

(1) - Two Pin Valet / Programming Switch

(1) - Two Pin Control Switch

(1) - Four Pin Shock Sensor Harness

(1) - Two Pin Door Lock Harness

(1) - Dual Stage Shock Sensor

(1) - Starter Inhibit Relay and Socket

(2) - 30 Amp In-line Fuse Holders With Fuses

(1) - Pin Switch Hardware Bag

(2) - Under Hood Caution Labels

(1) - Installation Manual

(1) - Operator's Manual

(1) - Limited Warranty

(2) - Window Decals

The APS-750a Remote Start/Alarm System is designed to be used with Automatic Transmission Ve-

hicles Only! The unit provides no output for glow plug pre-heat and may not be desirable for diesel

vehicles. If the diesel engine has a instant fire, (no glow plug pre-heat system), a tach signal input, and

an Automatic Transmission, this unit may be used. For diesel applications, consult your dealer for the

type of ignition system in your particular vehicle.

INSTALLATION OF THE MAJOR COMPONENTS:

CONTROL MODULE:

Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting

location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin

main wiring harness.

Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting

the module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap

around or block the steering wheel preventing proper control of the vehicle. Secure the module in the

chosen location using cable ties or screws as necessary.

Do Not Mount The Module In The Engine Compartment, as it is not waterproof.

SIREN:

Select a location in the engine compartment that is not accessible from below the vehicle. The selected

location must be clear of hot or moving parts within the engine compartment The siren must be pointed

downward to prevent water retention and the flared end must be pointed away from and out of the engine

compartment for maximum sound distribution. Before securing the siren, check behind your chosen

location to assure that the mounting screws will not penetrate any factory wiring or fluid lines. Secure the

siren mounting bracket using #8 self taping screws or by first using the mounting bracket as a template,

scribe or mark the three bracket mounting holes. Drill the three marked holes using a 1/8" drill bit, than

mount the siren using #8 sheet metal screws.

HOOD AND TRUNK PIN SWITCHES:

The pin switches included in this package are intended for protecting the hood and trunk areas of the

vehicle. In all cases, the switch must be mounted to a grounded metal surface. When the pin switch is

activated, (hood/trunk open), it will supply a ground to the input wire activating the alarm. In addition, the

hood switch is required for the safety shut down of the remote start unit. If the vehicle is being worked on,

this hood switch prevents the remote start activation even if the RF command to start is issued. This

switch must be installed in all applications Failure to do so may result in personal injury or property

damage. Mount the switches in the hood and trunk locations away from water drain paths. If necessary,

the included brackets may be used to move the switch away from rain gutters or allow mounting to the

firewall behind the hood seal. In both cases the switch must be set up to allow the hood or trunk door to

depress the switch at least 1/4 inch when the hood or trunk is closed and fully extended when the hood

or trunk is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully check behind the

chosen location to insure the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4"

hole in the desired location and thread the pin switch into it using a 7/16" nut driver or deep well socket.

If using the mounting bracket, first secure the bracket to the desired location and secure the pin switch in

the pre-threaded mounting bracket hole.

DASH MOUNTED L.E.D.:

The small Red LED included in the kit will serve as a visual indicator of the alarm's status and provide a

visual deterrent to a potential thief. The LED also provides important feed back information during the

transmitter and feature program modes. The LED should be installed in the dash in an area highly visible

so that it may be seen from the driver's seat as well as from outside the vehicle. Inspect behind the

chosen location to insure that the drill will not penetrate any existing factory wiring or fluid lines. Carefully

drill a 1/4" hole in the desired location and pass the connector end of the LED through the hole and toward

the control module. Press the LED firmly into place until it is fully seated in the mounting hole.

THE RANGE EXTENDER ANTENNA:

The range extender antenna provided with this unit allows routing from below the dash board for maximum

operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.

Special considerations must be made for windshield glass as some newer vehicles utilize a metallic

shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the exposed, (non

shielded) end toward a rear window location for best reception. Secure the exposed end with double stick

tape or instant stick glue. After securing the exposed end of the antenna with the tape or glue, we advise

also securing a section of the antenna cable to a fixed support. This will prevent the antenna from

dropping down in case the double stick tape is exposed to extreme heat which may loosen it's gummed

surface.

VALET/PROGRAM/MANUAL OVERRIDE SWITCH :

Select a mounting location that is easily accessible to the operator of the vehicle. It is not necessary to

conceal the switch however concealment is recommended as it offers a higher level of security. The

switch can be mounted to the lower dash panel in the drivers area. Inspect behind the chosen location to

insure that adequate clearance is allowed for the body of the switch, and also that the drill will not

penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and mount the

switch by passing it through the panel from the underside. Secure the switch using the nut, star washer,

and on/off face plate. It is suggested that the switch be oriented to allow the on position to be up toward

the driver and the off position to be down or away from the driver. Route the switch's connector toward the

control module.

CONTROL SWITCH:

Select a mounting location known and accessible to the operator of the vehicle. A lower dash panel, kick

panel, or glove box is desirable. Inspect behind the chosen location to insure that adequate clearance is

allowed for the body of the switch, and also that the drill will not penetrate any existing factory wiring or

fluid lines. Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel

from the underside. Secure the switch using the nut, star washer, and on/off face plate. It is suggested

that the switch be oriented to allow the on position to be up toward the driver and the off position to be

down or away from the driver. Route the switch's connector toward the control module. Place the RED

rubber boot, included in the kit, over the switch handle to differentiate this switch from the valet/program

switch.

SHOCK SENSOR:

Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operation

from all areas of the vehicle. The selected location must be within 18" of the control module to allow

routing and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two

#8 self taping sheet metal screws. The sensor can also be secured to an existing dash brace using cable

tie straps. Whichever mounting method is used be sure to allow access to the sensitivity adjustment

potentiometer for use later in the installation.

STARTER INHIBIT RELAY:

Select a mounting location within 12" of the ignition switch's low current start solenoid wire. Secure the

relay to an existing harness in the chosen location using a cable tie around the relay's wiring harness.

Caution! Do not wire tie the metal bracket to an existing wiring harness as vibration may cause chaffing

and shorting damaging the factory wiring. If an existing harness is not available then secure the relay's

metal mounting tab to an under dash metal brace with a #8 self taping sheet metal screw. Wire the relay

as per the diagram found later in this manual.

The APS-750a is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combi-

nation Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT

be installed into a vehicle with a manual operated transmission. Doing so may result in serious personal

injury and property damage.

IMPORTANT!

DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS

INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE.

AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE

BATTERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS.

WIRING THE 6 PIN MAIN POWER HARNESS:

RED w/ WHITE Trace Wire: + 12 volts Battery 1 Source

Connect this wire toa+12VDCconstant source found at the vehicle's ignition switch using the 30 Amp

fuse and holder provided.

RED Wire: + 12 Volts Battery 2 Source

Connect this wire toa+12VDCconstant source found at the vehicle's ignition switch using the 30 Amp

fuse and holder provided, but NOT the same vehicle wire as used by the battery 1 source. Most vehicles

have more than one battery source supplying power to the ignition switch. Separate feed wires must be

used for the Red and Red/White wires. If your vehicle does not have two battery feed wires at the ignition

switch then it is possible to connect both wires to the vehicle's battery.

IMPORTANT!

It is the responsibility of the installing technician to determine the load factor of the vehicles electrical

circuits when the vehicle is running and to adequately fuse the two power wires based on that load. If the

vehicle, running under load with the air conditioned, heater blower motor, and accessories exceed 24

Amps continuous, we recommend that two fuses be used in combination on each power wire as shown

YELLOW Wire: Starter Output

Careful consideration for the connection of this wire must be made to prevent the vehicle from

starting while in gear. Understanding the difference between a mechanical and an electrical

Neutral Start Switch will allow you to properly identify the circuit and select the correct installa-

tion method. In addition you will realize why the connection of the safety wire is required for

all mechanical switch configurations.

Failure to make this connection properly can result in personal injury and property damage.

In all installations it is the responsibility of the installing technician to test the remote start unit and assure

that the vehicle cannot start via RF control in any gear selection other than park or neutral.

In both mechanical and electrical neutral st art switch configurations, the connection of the Yellow wire will

be made to the low current start solenoid wire of the ignition switch harness. This wire will have +12 volts

when the ignition switch is turned to the start (crank) position only. This wire will have 0 volts in all other

ignition switch positions.

NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the

electrical neutral switch configuration, this connection must be made between the starter inhibit relay,

( when used ) and the neutral safety switch as shown in the following diagram.

Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in

personal injury and property damage.

SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.

below. For additional information see Tech Update issued 9/30/96.

BLUE Wire: Ignition 1 Output

Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the

ignition key is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions, and will have 0

volts when the key is turned to the "OFF" and "ACCESSORY" positions.

GREEN Wire: Ignition 2 Output

Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the

ignition key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position.

This wire will show 0 volts when the key is turned to the "OFF" and "ACCESSORY" positions.

VIOLET Wire: Accessory Output

Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the

ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions, and will show 0 volts when

the key is turned to the "OFF" and "START" or "CRANK" positions.

YELLOW START WIRE DETAIL

WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness

White w/ Red Trace Wire: Parking Light Flasher Feed

This wire is the common contact of the on board parking light flasher relay. If the vehicle you are working

on has +12 volt switched parking lights, connect this wire to a fused + 12 volt source. (Max. 15 Amps)

NOTE: If the vehicle's parking lights are ground switched, connect this wire to chassis ground.

White Wire: Parking Light Flasher Output

This wire is the normally open contact of the on board parking light flasher relay. Connect this wire to the

vehicle parking light feed wire. See diagram below for details on wiring positive switched parking light

circuits.

White w/ Black Trace Wire: (+) Siren Output

This is the positive siren feed wire. Route this wire through a grommet in the firewall to the siren

location. Connect the White w/ Black Trace wire to the Red wire of the Siren. Secure the Black wire

of the Siren to a known chassis ground or solid clean metal surface.

Parking Light Wiring Detail

Siren Wiring Detail

SIREN



TO WHITE w/BLACK WIRE OF MODULE

RED

BLACK

(-) TO VEHICLE'S CHASSIS GROUND

Purple Wire: (+) Door Trigger Input

If the vehicle's door courtesy light switches + 12 volts when the door is opened, (Most Fords and some

Imports), you must connect this wire to the positive output from one of the vehicle's door pin switches. In

most cases, the Purple wire will need to be connected to only one door switch no matter how many doors

the vehicle has as most door lighting circuits are wired in parallel. See below for wiring details.

Positive Door Switch Wiring Detail

Hood Pin Switch Detail

Dark Green Wire: (-) Instant Trigger Input

This is the instant on ground trigger input wire. This wire must be connected to the hood and trunk pin

switches previously installed.

Note: This wire will be shunted when remote control channel 2 is accessed, (trunk release). This wire will

remain shunted all the while there is ground present and for 5 seconds after the ground is removed. This

allows the operator to open the trunk via the remote transmitter without having to first disarm the alarm

system. See below for wiring detail.

General Motors VATS By-Pass Diagram

Light Blue Wire: Ignition 3 Output

This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit

initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit

turns off. In all of the applications described below, a relay will be required.

The Light Blue wire can be used to accommodate the following situations:

A. Shock Sensor By Pass:

If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during the

Remote S tart activation period, then vibration from the running vehicle can cause the alarm to trigger. In

this case, connect the Light Blue Wire to terminal #86 of a external relay. Connect terminal# 85 of the

relay to a fused + 12 volt battery source. Cut the shock sensor trigger wire and connect one end of the

cut wire to terminal #30 and the other end of the cut wire to terminal #87a. Just before the Remote Start

unit is activated, the relay contacts will open, preventing the shock sensor's operation until the Remote

Start unit shuts off.

B. Ignition 3 Output:

Some newer vehicles use a third ignition wire which is required to start and keep the vehicle's engine

running. If this is the case, connect the Light Blue wire to terminal #86 of an external relay. Connect

terminal # 30&#85toafused + 12 volt battery source rated for a minimum of 25 Amp. Connect

terminal # 87 to the third ignition wire in the vehicle.

C. GM VATS Key Override:

If the vehicle has the General Motors VATS system installed, you will need to by-pass the system while

the vehicle is operating under the control of the Remote Start Unit. To Do This;

1. Measure the resistance of the resistor pellet on the ignition key then select a resistor within 5% of the

key's value from the resistor pack supplied.

2. Locate the pair of VATS wires in the vehicle, usually a pair of thin gauge wires running from the

ignition switch to the VATS control module.

NOTE: These wires are typically White w/ Black trace and Violet w/ Yellow trace, however in later model

Cadillacs, they are run through an orange sleeve, and are either both Black, both Yellow, or both White

wires. Consult the factory service manual for additional information.

3. Connect the Light Blue Wire from the Remote Start Unit to terminal #86 of an external relay. Connect

terminal #85 of the relay to a fused + 12 volt battery source.

4. Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal #87a of the

relay. Connect the other side of the (#1) wire to terminal #30.

5. Connect the previously selected resistor from terminal #87 to the second (#2) wire (as shown).

NOTE: The above information and following diagram is for the GM VATS system only. For GM PASS

LOCK System you will require the Audiovox AS-PASS II Module.

Green w/ White trace Wire: Entry Illumination Ground Output

This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the

alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. This

wire should be connected to an external relay, and wired to the vehicles interior entry lighting whenever the

optional Interior Illumination circuit is desired. See below for relay wiring details.

Entry Illumination Detail

Grey w/ Black Trace Wire: Negative Inhibit Input

The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module whenever

it is grounded. Connect the Grey w/ Black trace wire to the hood pin switch previously installed. This wire

must be routed through a grommet in the firewall and connected to the hood pin switch. If the pin switch

is to be used with an alarm system, connect this wire using the diode assembly provided.

IMPORTANT! This connection is a safety wire and must be connected as shown and tested as specified.

Failure to do so may result in personal injury or property damage. See detail of wiring in the following

diagram. This wire may also be used if the vehicle brake light circuit switches ground to the brake lights.

An isolation diode must be used for ground switched brake light circuits and must be connected to the

output of the brake switch.

Grey w/ Black Trace Negative Inhibit Safety Shut Down Detail

Orange Wire: Ground When Armed Output

This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit

relay. Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85

(red wire) of the relay to an ignition wire in the vehicle that is +12 volts when the ignition switch is turned to

the on and start positions and off when the key is off. Locate and cut the low current start solenoid wire

found at the vehicles ignition switch harness. This wire will have + 12 volts when the ignition key is moved

to the start (crank) position and will have 0 volts in all other key positions. Connect one side of the cut wire

to terminal #87a ( Black wire) of the relay. Connect the other side of the cut wire to terminal #30 (White/

Black wire) of the relay. See below for detail of wiring, also see Yellow Start wire detail for connection to

vehicle considerations.

Brown w/ Black Trace Wire: Positive Inhibit Input

The Brown w/ Black Trace wire provides an instant shutdown for the Remote Start Control module when-

ever it gets + 12 volts. If the Brake lights switch in the vehicle switches + 12 volts to the brake light circuit,

connect the Brown w/ Black trace wire to the output side of the brake switch. This will allow the Remote

Start to shut down if an attempt is made to operate the vehicle without the key while running under the

control of the Remote Start. In most vehicles, in order to shift into gear, the brake pedal must be de-

pressed. The brake input will in turn cause the remote start unit to shut off. See detail in the following

diagram for wiring the brake light circuit.

Brake Switch Positive Shutdown Detail

Starter Inhibit Wiring Detail

Black

White/Black

Black Wire: Chassis Ground Source

Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be

certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal.

Chassis Ground Connection Detail

Green w/ Orange Trace Wire: Tachometer Input Signal

This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start

module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine

compartment and connect to the negative side of the ignition coil. This Remote Start unit learns the tach

rate of the vehicle and in most cases will operate properly from one multi coil pack regardless of the number

of cylinders. If the vehicle has a single coil unit for each cylinder, it may be necessary to connect this wire

to more than one cylinder for proper tach reference. See multi coil wiring detail shown later in this manual

for additional information.

Tachometer Input Wiring Detail

Brown Wire: Negative Door Trigger

If the vehicle's door courtesy light switches ground when the door is opened, (Most GMs and Imports), you

must connect this wire to the negative output from one of the vehicle's door pin switches. In most cases the

Brown wire will need to be connected to only one door switch no matter how many doors the vehicle has as

most door lighting circuits are wired in parallel. See below for wiring detail.

Negative Door Switch Wiring Detail

Dark Blue Wire: Delayed 300mA Pulsed Channel 2 Output

The Dark Blue wire supplies a 300mA ground pulsed output whenever channel two of the receiver is accessed.

Pressing the pre-programmed transmitter button for three seconds will access channel two. This is a low

current output and must be connected to a relay to supply power to the trunk release or the circuit you wish

to control. Connect the Dark Blue wire to terminal # 86 of a VF45F11 P&B relay or equivalent. Connect

terminal # 85 of the relay to a fused + 12 volt source. Connect the common, normally open, and normally

closed contacts of the relay to perform the selected function of channel 2. See below for relay wiring detail.

Channel 2 Relay Wiring Detail

Green w/ Black Trace Wire: 300mA Latched Channel 3 Output

The Green w/ Black Trace wire supplies a 300 mA switched output whenever channel three of the receiver

is accessed. Pressing the pre-programmed transmitter button(s) will access channel three and will remain

active for as long as the transmitter button(s) is held. This is a low current output and must be connected

to a relay to supply power to the device you intend to control. Connect Green w/ Black Trace wire to

terminal #86 of a VF45F11 P&B relay or equivalent. Connect terminal #85 of the relay to a fused + 12 volt

source. Connect the common, normally open, and normally closed contacts of the relay to perform the

selected function of the channel 3 output.

WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS

The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during

different stages of the Remote Start unit's operation. Understanding these outputs and the time in which

they occur will allow you to determine if they are needed for the particular vehicle you are working on as well

as how to use them.

Black w Blue Trace Wire: Pulsed Ground Output Before Start

The Black w/ Blue Trace wire will provide a 300 mA pulsed ground output 3 seconds before the remote start

unit activates. Typical use for this output would be to disarm a factory theft deterrent system to prevent

false triggering of the factory alarm when the remote start unit engages.

Black w/ Light Green Trace Wire: Pulsed Ground Output After Start

The Black w/ Light Green Trace wire will provide a 300ma pulsed ground output after the vehicle is started

under control of the remote start unit. T ypically this wire will be used to re-lock the vehicle doors if the doors

unlock automatically when the factory anti-theft system is disarmed.

Black w/ Red Trace Wire: Pulsed Ground Output After Shutdown

The Black w/ Red Trace wire will provide a 300 mA pulsed ground output after the remote start unit shuts

down. This output will occur regardless of whether the circuit times out or is manually terminated. Typi-

cally this output will be used to re-lock the vehicle doors if the doors unlock automatically when the ignition

circuit transitions to off.

Black w/ Yellow Trace Wire: Ground Output During Start (Crank)

The Black w/ Yellow Trace wire will provide a 300 mA ground output while the starter output of the remote

start unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GM

vehicles. This wire is also referred to as the ECM wake up wire in some Chrysler vehicles.

NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement

is more than 300 mA.

2 Pin Control Switch: (Red Connector)

The Black & Black w/White Trace wires loaded in the two pin red connector enable the operation of the

Remote Start unit. When the Black w/ White Trace wire is grounded, the remote start unit is operable.

When this wire is open from ground, the remote start is disabled. Route the twin lead Black & Black w/

White Trace wires from the control switch to the remote start unit and plug red two pin connector into the

mating red two pin connector shell of the control module.

4 Pin Shock Sensor: (White Connector)

The Red (+12 volt), Black (ground), Blue (pre-detect) and Green (full trigger when armed) wires loaded into

the white connector shell are the inputs/outputs of the shock sensor. Route the 4 wire harness from the

shock sensor to the remote start control unit and plug the 4 pin white connector into the mating 4 pin

connector shell of the control module. Note: While operating under the control of the remote start unit the

shock sensor will be shunted (by-passed). Once the remote start shuts down, the shock sensor will be

re-enabled.

2 Pin LED Harness: (White Connector)

The Red & Blue wires loaded into the two pin mini white connector control the anode and cathode of the

dash mounted LED. Route the twin lead Red and Blue wires from the LED to the remote start control unit

and plug the two pin connector into the mating white mini connector shell of the control module.

2 Pin Valet/Program Switch: (Blue Connector)

The Black & Grey twin lead wires loaded in the two pin blue connector are the ground supply and

program/valet input of the Remote Start unit. When the Grey wire is grounded, under certain conditions,

the unit will enter the valet mode. When the Grey wire is sequentially grounded under other conditions,

the unit will enter the various program modes. Route the twin lead Black and Grey wires from the valet/

Program switch to the remote start unit and plug the two pin connector into the mating blue connector

shell of the control module. Refer to the remote programming, feature programming and function pro-

gramming shown later in this installation guide for operation of the valet/program switch.

2 Pin Door Lock/Unlock Harness: (White Connector)

The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to

control the vehicle door lock / unlock circuits. The output of these wires has a maximum switching

capability of 300mA. Many vehicles today have factory door lock relays which can be connected directly

to these outputs, however always confirm that the factory relays in your particular vehicle do not exceed

the rated 300mA output of the units door lock/unlock circuit. Plug the two pin connector of the door lock/

unlock harness into the mating connector shell of the control module. Determine the door lock circuit of

the vehicle you are working on and wire according to the diagrams shown.

3 Wire Ground Switched Door Lock Circuits:

In this application, the Red wire of the two pin harness provides a ground pulse during the arming se-

quence, or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from

the factory door lock switch to the factory door lock relay.

The Green wire of the two pin harness provides a ground pulse during the disarming sequence, or pulsed

ground unlock output. Connect the Green wire to the low current ground signal wire from the factory door

unlock switch to the factory door unlock relay. See Below For Wiring Detail.

3 WireGround Switched Door Lock/Unlock Wiring Detail

3 Wire Positive Switched Door Locks:

In this application, the Red wire of the two pin harness providesa+12volt pulse during the disarming

sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from

the factory door unlock switch to the factory door unlock relay.

The Green wire of the two pin harness providesa+12volt pulse during the arming sequence, or pulsed 12

volt lock output. Connect the Green wire to the low current 12 volt signal wire from the factory door lock

switch to the factory door lock relay. See Below For Wiring Detail.

3 Wire Positive Switched Door Lock/Unlock Wiring Detail

Note: For connection to Four Wire Polarity Reversal, 5 Wire Alternating 12 Volts, And All Other Door

Lock Circuits the Audiovox AS-9159 Door Lock Interface, (or equivalent 30 A automotive relays) must be

used. Refer to the Audiovox Door Lock Wiring Supplement for proper wiring of these circuits.

ALARM SELECTABLE FEATURES

NOTE: The Alarm Selectable Features and Remote Start Selectable Features programming steps following are

based on transmitter button 1 being programmed for channel 1 and transmitter button 2 being programmed for

channel 2.

RF Programmable Features:

Feature Selection 1 Chirp 2 Chirp Default

First 1 Second Door Locks 3.5 Second Door Lock 1 Second

Second Auto Lock On Auto Lock Off Auto Lock Off

Third Auto Unlock On Auto Unlock Off Auto Unlock Off

Fourth Passive Door Locks Active Door Locks Active Door Locks

Fifth Passive Arming Active Arming Passive Arming

To Program The Alarm's Selectable Features:

LED Flash Pattern

1 Flash Pause etc.

2 Flash Pause etc.

3 Flash Pause etc.

4 Flash Pause etc.

5 Flash Pause etc.

First

Second

Third

Fourth

Fifh

Action

Turn the ignition switch on

Flip the valet/program switch on then off 3 times

Within 3 seconds, turn the ignition switch off

and then on.

Press transmitter button 1 to change.