Taco Comfort Solutions VT2218HY2FC1A00 Mode d'emploi

Marque: Taco Comfort Solutions

Modèle: VT2218HY2FC1A00

Taper: Mode d'emploi

00e

Series VT2218

Instruction Sheet

102-525

SUPERSEDES: June 14, 2016 EFFECTIVE: April 24, 2017

Plant ID No. 001-4267

Delta-T Variable Speed, ECM High-Efficiency Circulator

DESCRIPTION:

The 00e

series VT2218 circulator is a temperature sensing, self-adjusting, variable speed

wet rotor circulator with an ECM, permanent magnet motor. Operating modes include

Delta-T, constant speed, set point heat, set point cool, and boiler protection. Its high

efficiency motor reduces power consumption by up to 85% compared to equivalent AC

permanent split capacitor circulators.

APPLICATION:

• Maximum operating pressure: 125 psi (862 kPa)

• Minimum water temperature: 36ºF (2ºC)

• Maximum water temperature: 230°F (110ºC)

• Electrical specifications:

Voltage: 110-120V, 50/60 Hz, single phase

Maximum operating power: 58W

Maximum amp rating: 0.67

• Equipped with a cast iron casing and should be used for closed loop systems only

• Taco circulator pumps are for indoor use only – employer uniquement a l’interieur

• Acceptable for use with water or maximum of 50% water/glycol solution

FEATURES:

• 5 operating modes:

- Delta-T - variable speed, maintains constant ∆T, provides exact GPM flow required

- Constant Speed - 4 fixed speeds, maintains constant flow for zoning

- Set Point Heat - variable speed with boiler protection option, decreases speed on temperature rise

- Set Point Cool - variable speed, increases speed on temperature rise

- Boiler Protection - protects boiler from low return temperature and flue gas condensation

• Illuminated LCD displays:

- Operating mode, speed or temperature setting, watts, gpm, supply temperature, return temperature, and

error code diagnostics.

• Use with a Taco ZVC Zone Valve Control or SR Switching Relay for ON/OFF operation.

• Integral Flow Check (IFC) is included in carton. Simply press into discharge flange if required

• Nut capture feature on flanges for easier fit up

• Whisper quiet operation

• BIO Barrier

protects the pump from system contaminants

• SureStart

automatic unblocking mode

• Optional, 2-way flange model available to reduce SKU’s and provide universal fit-up to any flange position

INSTALLATION:

WARNING: Do not use in swimming pool or spa areas. Pump has not been investigated for these applications.

AVERTISSEMENT: Ne pas utiliser dans une piscine ou un spa. La pompe n'a pas été étudiée pour ces applications.

CAUTION: The addition of petroleum based fluids or certain chemical additives to systems using TACO equipment voids the

warranty. Consult factory for fluid compatibility.

ATTENTION: L'ajout de liquides à base de pétrole ou de certains additifs chimiques à des systèmes utilisant un équipement TACO

annule la garantie. Consultez le fabricant pour connaître la compatibilité de liquides.

CAUTION: Installations at elevations over 5000 feet must have higher fill pressure of 20 psi minimum to prevent pump cavitation

and flashing. Premature failure may result. Adjust expansion tank pressure to equal fill pressure. A larger size expansion tank may

be required.

ATTENTION: Des installations à des altitudes de plus de 1600 mètres doivent présenter une pression de remplissage plus élevée

de 20 psi au minimum afin d'éviter toute cavitation ou flashing de la pompe. Une défaillance prématurée peut en résulter. Réglez

la pression du réservoir d'expansion de façon qu'elle soit égale à la pression de remplissage. Un réservoir d'expansion d'une taille

supérieure peut être nécessaire.

For more information, visit

www.TacoComfort.com

Use for pumps with

date code 09-17

or after

KEY:

VI, V2, V3 = SHUT-OFF ISOLATION VALVE

P = TACO CIRCULATOR WITH IFC

FF = FAST FILL BOILER FEED VALVE

PV4 = PURGE VALVE

RECOMMENDED PURGING STEPS:

1. CLOSE V1, PV4, V2

2. OPEN V3

3. OPEN FF VALVE

4. OPEN V2, PV4, TO PURGE LAST ZONE

FIRST (ZONE 3)

5. CLOSE FF VALVE

6. CLOSE V2, PV4

7. REPEAT STEPS 1 TO 6 FOR EACH

ADDITIONAL ZONE, PURGE ZONE 1 LAST

8. OPEN V1 WHEN ALL ZONES ARE

PURGED

9. ADJUST SYSTEM TO DESIRED OPERATING

FILL PRESSURE IF REQUIRED

KEY:

VI, V2, V3 = SHUT-OFF ISOLATION VALVE

P = TACO CIRCULATOR WITHOUT IFC INSTALLED

FF = FAST FILL BOILER FEED VALVE

PV4 = PURGE VALVE

ZV = ZONE VALVE

RECOMMENDED PURGING STEPS:

1. CLOSE V1, PV4, V2

2. OPEN V3 AND ZV3

3. OPEN FF VALVE

4. OPEN V2, PV4, TO PURGE LAST ZONE FIRST (ZONE 3)

5. CLOSE FF VALVE

6. CLOSE V2, PV4

7. REPEAT STEPS 1 TO 6 FOR EACH ADDITIONAL ZONE,

PURGE ZONE 1 LAST

8. OPEN V1 WHEN ALL ZONES ARE PURGED

9. ADJUST SYSTEM TO DESIRED OPERATING FILL

PRESSURE IF REQUIRED

10. MOVE ALL ZV TO CLOSED/AUTOMATIC POSITION

ACCEPTABLE MOTOR MOUNTING POSITIONS CASING ROTATION

To rotate the casing, remove the 4 motor screws and spin the

casing to the desired flow direction. Reattach the 4 screws

(

⁄

" allens wrench required). Be sure body gasket is seated

evenly to prevent leakage. Tighten motor screws to 34-42 in-

lbs torque.

Position electrical knockout at 6 o’clock position for best programming and LCD viewing orientation. Casing

may be rotated to change flow direction.

cross a Series

Loop System Using

Zone Valves

Return

Sensor

Across Multi-Zone

adiant Manifolds

ith Loop Actuators

iSeries-R

MM MM MM MM

Outdoor

Sensor

Boiler

Sensor

Supply

Sensor

Supply

Sensor

Return

Sensor

Boiler

Return Sensor

Boiler Protection By-Pass

Duct

Supply

Sensor

an Coil Fixed Temperature

Typical Variable Speed Applications:

Supply

Sensor

Boiler Return

Sensor

Mixing

adiant Injection Set Point with Boiler Protection Option

•

Delta-T

- Varies speed to maintain

a constant temperature

differential (∆T)

• Set Point Heat

- Varies speed to maintain

a fixed temperature

• Boiler Protection Option

- Decreases speed to protect

boiler from low return water

temperature and flue gas

condensation

• Boiler Protection

- Increases speed to protect boiler from low return

water temperature and flue gas condensation

• Heating or Chilled

Water Cooling

• Set Point Heat

- Decreases speed

on temperature rise

• Set Point Cool

- Increases speed on

temperature rise

1. Location:

The circulator can be installed on the supply or return side of the boiler but for best system performance, it should always pump

away from the expansion tank. See piping diagrams in Figures No.1 and No. 2.

Integral Flow Check (IFC

) option - An IFC

is included in the carton. If required, press IFC into machined discharge port with plunger

and o-ring facing in, until it snaps into place. Before installing, press IFC plunger to be sure it moves freely. See diagram below.

2. Mounting position:

Circulator must be mounted with the motor in the horizontal position. See diagrams below for acceptable motor mounting orientations.

CAUTION: Do not use flat rubber gaskets. Only use O-ring gaskets provided or leaks may result. Warranty will be void.

HOT

NEUTRAL

GROUND

BLACK

WHITE

GREEN

SCREW

TERMINAL BOX

• Disconnect AC power supply. Remove terminal box cover. Thread a wiring connector into npt knockout. Note: To install an angle connector

removal of sensor cap may be required for clearance. Connect hot wire to black lead and neutral wire to white lead. Connect ground wire to Green

Ground screw. Replace terminal box cover.

• Remove sensor cap. Slide sensor wires through grommet in sensor cap. See diagram above.

• Attach sensor wires provided as shown:

- Delta-T mode uses supply and return (S + R).

- Set Point mode uses supply (S) for system sensor and return (R) for boiler protection return sensor.

• Attach sensors to supply and return piping using the zip-ties provided. See diagram above.

- In Delta-T mode, place sensors on system supply and return.

- In Set Point Heat mode, place supply sensor on system loop supply. If boiler protection option is used, place return sensor on boiler return.

• Insulate pipe around sensors as shown.

5. Start the circulator:

Note: When power is applied to the circulator it will go through a 10 second diagnostic delay before starting. The LCD will illu-

minate for the first 5 minutes of a run cycle. Press any of the programming buttons to re-illuminate the LCD.

When air purging the system, it is recommended to run the circulator at full speed long enough to remove all remaining air from the bear-

ing chamber. This is especially important when installing the circulator in the off-season.

Full Speed Over-Ride Feature:

To run the pump at full speed during the fast fill, start-up and purge process, press and hold the UP button for 3 seconds until “Full Speed

Override” appears on the LCD display. To return to the programmed, normal operating mode, press the SET button.

“SureStart

” Feature: In rare cases where a locked rotor may occur, the SureStart feature will activate automatically and rapidly vibrate

to unblock the rotor and continue normal operation.

6. Programming your VT2218 circulator:

Note: The VT2218 is factory-programmed for Delta-T operating mode with a 20°F temperature differential setting. If this is your

desired operating mode and Delta-T setting, no programming changes are required.

CAUTION: Never run the circulator dry or permanent damage may result.

ATTENTION: Ne laissez jamais le circulateur tourner à sec, des dommages permanents peuvent en résulter.

The VT2218 has 5 Operating Modes:

• Delta-T - Varies speed to maintain a fixed temperature differential (factory pre-set mode).

• Constant Speed - 4 fixed speeds (see pump curves on page 8 to select desired performance).

• Set Point Heat - Increases speed to increase temperature (includes Boiler Protection option).

• Set Point Cool - Increases speed to lower temperature.

• Boiler Protection - Varies speed to maintain minimum boiler return temperature.

WARNING: Use supply wires suitable for 90°C,

AVERTISSEMENT: Employer des fils d’alimentation adeqauts pour 90°C.

3. Fill the system with tap water or a maximum of 50% propylene-glycol and water solution:

The system must be filled before operating the circulator. The bearings are water lubricated and should not be allowed to operate

dry. Filling the system will result in immediate lubrication of the bearings. It is always good practice to flush a new system of foreign

matter before starting the circulator.

CAUTION: To reduce the possibility of noise transmission, be sure to add vibration dampeners to piping when

ounting circulator to wall or floor joists.

ATTENTION: Pour réduire la possibilité de transmission de bruit, veillez à ajouter des amortisseurs de vibration à la

tuyauterie lors du montage du circulateur sur des chevêtres de mur ou de plancher.

WARNING: Risk of electric shock. To reduce the risk of electric shock, be certain that it is connected only to a prop-

erly grounded, grounding-type receptacle. Follow all local electrical and plumbing codes.

AVERTISSEMENT: Risque de choc électrique. Pour réduire le risque de choc électrique, veillez à ce qu'elle soit rac-

cordée uniquement à un réceptacle de type mise à la terre proprement mis à la terre. Respectez tous les codes de

plomberie et électriques locaux.

4. Wiring the circulator:

Sensor Cap with Grommet

Return Sensor (R)

Supply Sensor (S)

ommon

Sensor Cap with Grommet

To change operating mode and settings:

a. Press and hold the SET button for 3 seconds until the operating mode

on the LCD begins to flash.

b. Use the UP or DOWN buttons to scroll through the 5 operating mode

options. When the desired mode flashes on the LCD, press the SET

button. The LCD will begin to flash either temperature or speed setting

options, whichever applies.

c. Use the UP button to increase temperature or speed settings. Use the

DOWN button to decrease temperature or speed settings. When the

desired setting flashes, press the SET button.

d. Your programming is complete and the operating mode and setting will

appear on the LCD screen.

US or Metric Units

The VT2218 can be programmed to display in either US or Metric units. The

default is US units

. To change units to Metric, use the programming steps

above to scroll to SETUP MODE. Press SET and the default US units will

begin to flash. Press the DOWN button to change to Metric. The UP button

will change back to US units. When the desired units are flashing, press the SET button.

7. Reading the LCD screen:

The LCD screen will display important diagnostic information:

Operating Mode - Delta-T, Constant Speed, Set Point Heat, Set Point Cool, or Boiler Protection.

Setting - Delta-T target, Fixed speed, Set Point target temperature, or Boiler Protection target minimum temperature.

Watts - Power usage of the circulator.

GPM - Flow rate through system.

S - Supply sensor temperature.

R (or BP) - Return sensor temperature (or Boiler Return temperature in Set Point mode).

8. Sequence of Operation - How the VT2218 Works:

Delta-T Mode (5°F - 50°F, default = 20°F)

In Delta-T mode, the VT2218 will start at the lowest speed. If it reads a temperature differential (∆T) LESS than its target, it will

gradually increase speed through a 3 minute “Start Cycle” to its highest speed, until target ∆T is reached. “Start Cycle” will dis-

play on the LCD screen in place of “Watts”. If ∆T is GREATER than target, the pump will immediately go into Variable Speed

operation and vary speed to maintain the target ∆T.

Constant Speed Mode (Speeds 1, 2, 3, 4, default = Speed 4)

In Constant Speed mode, the VT2218 will always start and run at the pre-set Speed Level (1 through 4). Only watts will be dis-

played. Temperature sensors are not active in this mode.

Set Point Heat Mode (with Boiler Protection (BP) option) (50°F - 220°F, default = 105°F, BP default = 140°F)

In Set Point Heat mode, the VT2218 will start at the lowest speed. It then immediately switches to Variable Speed operation,

increasing speed to raise

temperature or decreasing speed to lower temperature and maintain the Set Point Heat target.

If Boiler Protection (BP) option is used with Set Point Heat, the return sensor (R) will over-ride the supply sensor (S) and slow

the pump down if boiler return water temperature falls below BP target (for example 140°F). Once the return sensor reads BP

target, the pump will then speed up to reach the supply temperature Set Point target. In this mode the return sensor will read

“BP” on the LCD.

Set Point Cool Mode (32°F - 100°F, default = 70°F)

In Set Point Cool mode, the VT2218 operates in the reverse of Set Point Heat. It will start at the lowest speed. It then immediately

switches to Variable Speed operation, increasing speed to lower

temperature or decreasing speed to raise temperature and

maintain the Set Point Cool target.

Boiler Protection (BP) Mode (100°F - 160°F, default = 140°F)

Note: Boiler Protection Mode is designed to maintain a minimum boiler temperature to prevent flue gas condensation.

CAUTION: Do not attempt to remove LCD panel from circulator. Serious damage to circulator electronics may

result.

ATTENTION: N'essayez pas de retirer le panneau de LCD du circulateur. Des dommages s

érieux à l'électron-

ique du circulateur peuvent en résulter.

9. Troubleshooting the error codes:

SureStart Feature: The VT2218 is programmed with an automatic unblocking feature. In the case of a locked rotor condition, it will

ttempt to unblock the rotor with a series of rapid oscillating actions. It will repeat this process up to 100 times. If still locked after

100 attempts, “LOCKED ROTOR” will apppear on the LCD. See error code listing below.

Listed below are potential diagnostic error codes which will appear on the LCD display in case of a malfunction.

Testing the Sensors

A good quality test meter capable of measuring up to 5,000 kΩ (1 kΩ = 1000----) is required to measure the sensor resistance.

In addition to this, the actual temperature must be measured with a good quality digital thermometer.

First measure the temperature using the thermometer and then measure the resistance of the sensor at the VT2218. The wires from

the sensor must not be connected to the circulator while this test is performed. The wiring terminals are easily removed by pulling

them from the circulator. Using the chart below, estimate the temperature measured by the sensor. The sensor and thermometer

readings should be close. If the test meter reads a very high resistance, there may be a broken wire, a poor wiring connection or a

defective sensor. If the resistance is very low, the wiring may be shorted, there may be moisture in the sensor or the sensor may be

defective. To test for a defective sensor, measure the resistance directly at the sensor location.

ERROR CODE* DESCRIPTION CORRECTIVE ACTION

SENSOR 1 MISSING Supply sensor disconnected. Reconnect sensor.

SENSOR 2 MISSING Return sensor disconnected. Reconnect sensor.

ENSOR 1 SHORTED

ad sensor.

eplace sensor.

SENSOR 2 SHORTED Bad sensor. Replace sensor.

AC INPUT UNDER VOLTAGE Low voltage problem. Check power supply.

AC INPUT OVER VOLTAGE High voltage problem. Check power supply.

LOCKED ROTOR Probable locked rotor or motor failure. Replace pump.

MOTOR OVER CURRENT Possible locked rotor or motor over current. Replace pump.

OVER TEMPERATURE PC Board overheating.

Pump will reduce current and speed until PCB

temperature is acceptable. If speed falls below

1650 RPM, pump will stop on safety. Cycle AC

power OFF/ON to restart.

SPEED TACO GRUNDFOS WILO B & G/XYLEM ARMSTRONG

1 003 Alpha-15-55 (1) - - -

2 006 Alpha-15-55 (2) - - Compass (1)

007

008

0015-1

0015-2

UP-15-42

UPS-15-58 (1)

UPS-15-58 (2)

Star S-21 (1)

Star S-21 (2)

NRF-25 (1)

NRF-25 (2)

Astro 230 (1)

Astro 230 (2)

Compass (2)

4 0015-3

UPS-15-58 (3)

Alpha-15-55 (3)

Star S-21 (3)

NRF-25 (3)

Eco-Vario

Astro 230 (3)

Compass (3)

Pump Cross Reference (Constant Speed Mode):

Temperature

Resistance Temperature Resistance Temperature Resistance Temperature Resistance

°F °C

-30 -34

234,196 30 -1 34,558 90 32 7,334 150 66 2,045

-20 -29 165,180 40 4 26,099 100 38 5,828 160 71 1,689

-10 -23 118,018 50 10 19,900 110 43 4,665 170 77 1,403

0 -18 85,362 60 16 15,311 120 49 3,760 180 82 1,172

10 -12 62,465 70 21 11,883 130 54 3,050 190 88 983

20 -7 46,218 80 27 9,299 140 60 2,490 200 93 829

MODE TACO GRUNDFOS WILO B & G/XYLEM ARMSTRONG

Delta-T 008-VDT Alpha 15-55 Stratos Eco 16FX Eco-Auto 19-14 Compass 2020

Pump Cross Reference (Delta-T Mode):

* Flashing Displayed on LCD

LIMITED WARRANTY STATEMENT

Taco, Inc. will repair or replace without charge (at

the company’s option) any Taco High Efficiency

circulator or circulator part which is proven defec-

tive under normal use within three (3) years from

the date of manufacture.

In order to obtain service under this warranty, it

is the responsibility of the purchaser to promptly

notify the local Taco stocking distributor or Taco

in writing and promptly deliver the subject product

or part, delivery prepaid, to the stocking distribu-

tor. For assistance on warranty returns, the pur-

chaser may either contact the local Taco stock-

ing distributor or Taco. If the subject product or

part contains no defect as covered in this war-

ranty, the purchaser will be billed for parts and

labor charges in effect at time of factory exami-

nation and repair.

Any Taco product or part not installed or operated

in conformity with Taco instructions or which has

been subject to misuse, misapplication, the addi-

tion of petroleum-based fluids or certain chemi-

cal additives to the systems, or other abuse, will

not be covered by this warranty.

If in doubt as to whether a particular substance

is suitable for use with a Taco product or part, or

for any application restrictions, consult the

applicable Taco instruction sheets or contact

Taco at (401-942-8000).

Taco reserves the right to provide replacement

products and parts which are substantially similar

in design and functionally equivalent to the

defective product or part. Taco reserves the right

to make changes in details of design, construc-

tion, or arrangement of materials of its products

without notification.

TACO OFFERS THIS WARRANTY IN LIEU OF

ALL OTHER EXPRESS WARRANTIES. ANY

WARRANTY IMPLIED BY LAW INCLUDING

WARRANTIES OF MERCHANTABILITY OR

FITNESS IS IN EFFECT ONLY FOR THE DURA-

TION OF THE EXPRESS WARRANTY SET

FORTH IN THE FIRST PARAGRAPH ABOVE.

THE ABOVE WARRANTIES ARE IN LIEU OF

ALL OTHER WARRANTIES, EXPRESS OR

STATUTORY, OR ANY OTHER WARRANTY

OBLIGATION ON THE PART OF TACO.

TACO WILL NOT BE LIABLE FOR ANY SPE-

CIAL, INCIDENTAL, INDIRECT OR CONSE-

QUENTIAL DAMAGES RESULTING FROM THE

USE OF ITS PRODUCTS OR ANY INCIDENTAL

COSTS OF REMOVING OR REPLACING

DEFECTIVE PRODUCTS.

This warranty gives the purchaser specific rights,

and the purchaser may have other rights which

vary from state to state. Some states do not

allow limitations on how long an implied warranty

lasts or on the exclusion of incidental or conse-

quential damages, so these limitations or exclu-

sions may not apply to you.

A Taco Family Company

2017

SHADED AREA IS

VARIABLE SPEED

OPERATING RANGE

VT2218 PERFORMANCE CURVES

Taco Comfort Solutions VT2218HY2FC1A00 Mode d'emploi

Marque: Taco Comfort Solutions

Modèle: VT2218HY2FC1A00

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Taco Comfort Solutions VT2218HY2FC1A00 Operating instructions

Taco Comfort Solutions VT2218HY2FC1A00 Mode d'emploi

Taco Comfort Solutions VT2218HY2FC1A00 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents