Schneider Electric EBIOTPGW Guide d'installation

Marque: Schneider Electric

Modèle: EBIOTPGW

Taper: Guide d'installation

Installation Sheet

028-6164-01-en, August 2023 | 1

4.5 (0.2) 35.5 (1.4)

REDUCED DEVICE PERFORMANCE

•

This device is for indoor use only and is not suitable for wet locations.

•

Do not install the device close to an exterior window.

•

When replacing a device, install the new device in the same position and direction as the replaced device.

Failure to follow these instructions can result in reduced device performance.

NOTICE

EcoStruxure Building-IoT Gateway

The IoT Gateway is a multi-protocol gateway that can simultaneously receive data from multiple wireless protocols. It is designed

for commercial facilities and building installations. The Gateway has built-in radios to allow for direct communication with sensors

in the IoT Sensor Solution product family. Multiple gateways can be installed to support thousands of sensors.

Regulatory Compliance and Safety Information

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is

assumed by Schneider Electric for any consequences arising out of the use of this material.

Carefully read these instructions and all information relevant to this product before trying to install it. See the list of technical

literature.

Dimensions

mm (inches) 149.3 (5.9) 40 (1.6)

Installation Restrictions

Installing the Device Connections and Buttons

1. For models with LTE option: Install the antennaa.

2. Use adapted screws to install the gateway on the wall.

3. Power on the gateway using the power adaptera or Power

over Ethernet (PoE).

The green LED will turn on solid to indicate the device is

operational. Otherwise, press the on/off button to power

it up.

DC Jack USB 2.0 SIM Card

Holder LTE

Antenna

1GBE RJ45

POE CAN On/Off

Button

Reset

Button

125 (4.9)

136 (5.4)

85.3 (3.4)

028-6164-01-en, November 2022 | 2

Part Numbers

Product Code / model number: EBIOTPGW Part Numbers

EcoStuxure Building-IoT Gateway

AC/DC Power supply (to be ordered separately) ICP12-120-1000DSD4

LTE Antenna (To be ordered separately for models supporting LTE) AN00010

EBIOTPGW

General Specifications

Maximum number of supported devices

IoT Sensor Solution sensors

200

Material

Enclosure

Plastic casing with internal antenna for Wi-Fi/

Bluetooth. One SMA port for LTE.

Mechanical

Dimensions

150L x 85W x 40H mm (5.9L x 3.3W x 1.6H in)

Weight

185 g (0.4 lb)

Electrical

Power

DC 9 - 36 V

Power over Ethernet (PoE) PD IEEE802.3AF

5W peak power

Hardware

RAM

1GB DDR4

Storage capacity

8GB eMMC

Connectors

1 x RS485 (option)

1 x CAN (option)

1 x USB 2.0 Connector, Type-A

1 x DC 9V - 36V power supply

Wireless connectivity

Communication protocol

2.4 GHz, Sensor Network supporting Mesh

Technology

Antenna type

Omnidirectional, internal.

WiFi Interface

2.4GHz/5GHz b/g/n/ac

module

Antenna type

Omnidirectional, internal.

FCC ID: 2BA24LBEE5HY1MW,

IC: 12107A-LBEE5HY1MW

LTE

1 x LTE Cat 4 Worldwide + GPS (with fallback

on 3G/2G)

FCC ID: XMR201903EG25G

IC: 10224A-201903EG25G

Optional AC/DC Power supply

Model ICP12-120-1000D

Input AC 100-240V

Output DC 12V-1A @ 40°C

Environment

Environmental conditions

Indoor use only

Ambient temperature, operating

0 to 50 °C (32 to 122 °F)

Ambient temperature, storage

-20 to 65 °C (-4 to 149 °F)

Humidity

0 to 95 % (non-condensing)

Installation

Mounting

Wall-mounted

Installation equipment, included

Mounting tape, screws, installation instructions

FCC ID: 2BATG-EBIOTPGW, IC: 30486-EBIOTPGW

Addendum - California Proposition 65 Warning Statement for California Residents

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause

cancer and birth defects or other reproductive harm, and Bisphenol A (BPA), which is known to the State of

California to cause birth defects or other reproductive harm. For more information, go to

www.P65Warnings.ca.gov.

Regulatory Notices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not

expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

028-6164-01-en, November 2022 | 2

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be

installed and operated with minimum distance 20 cm (7.9 inches) between the antenna and your body during normal operation. Users must follow the specific operating

instructions for satisfying RF exposure compliance.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B) / NMB-003 (B).

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada

applicables aux appareils radio exempt de licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) L’appareil ne doit pas produire de brouillage;

(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Cet appareil numérique de la Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with

minimum distance 20 cm (7.9 inches) between the radiator and any part of your body. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Cet équipement est conforme aux limites d’exposition aux radiations ISED CNR-102 établies pour un environnement non contrôlé. Une distance de séparation d'au

moins 20 cm doivent être maintenue entre l'antenne de cet appareil et toutes les personnes. Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec

d’autres.

This radio transmitter 30486-EBIOTPGW has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed

below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed

are strictly prohibited for use with this device.

Le présent émetteur radio IC: 30486-EBIOTPGW a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types

d'antenne énumérés ci‑dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal

indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur.

Under Innovation, Science and Economic Development regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d'Innovation, Sciences et Développement économique Canada, le présent émetteur radio peut fonctionner avec une antenne d'un

type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Innovation, Sciences et Développement économique Canada. Dans le but de réduire les risques

de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Approved Antenna Type:

Maximum gain: 3 dBi

Antenna type: FPC (Flexible Printed Circuit)

Radiation pattern: Omni-Directional

Impedance: 50 Ohm

Connector type: U.FL

www.se.com/buildings