Niko Swiss Garde 300 Presence Detector Mode d'emploi

Marque: Niko

Modèle: Swiss Garde 300 Presence Detector

Taper: Mode d'emploi

2524X_2525XCH_ETS_description EN

2524X/2525XCH

SWISS GARDE 300 PRESENCE DETECTOR KNX/KLR

APPLICATION DESCRIPTION

SWISS GARDE 300 PRESENCE KNX/KLR

DESCRIPTION DU PROGRAMME D‘APPLICATION

SWISS GARDE 300 PRÄSENZ KNX/KLR

APPLIKATIONSBESCHREIBUNG

SG300P KNX/KLR

SG300P KNX/KLR IP55 UP

SG300P KNX/KLR IP55 AP

25240 / 25251CH / 25252CH

25241 / 25245

25242 / 25248

EN 2524X_2525XCH_ETS_description

2524X/2525XCH

Content table

1. Functional Description ........................................................................................................................................................................ 3

1.1 Model overview .......................................................................................................................................................................... 3

1.2 Dimensions ................................................................................................................................................................................ 3

2. Communication Objects ..................................................................................................................................................................... 4

3. Parameters ....................................................................................................................................................................................... 4

3.1. General ...................................................................................................................................................................................... 4

3.2. Light - Switch / Dimming / Standby values ................................................................................................................................... 5

3.3 HVAC ......................................................................................................................................................................................... 7

3.4 Brightness / Threshold switch / Value calibration .......................................................................................................................... 7

3.5 Brightness value calibration ........................................................................................................................................................ 8

3.6 PIR evaluation ............................................................................................................................................................................ 8

3.7 Constant light control .................................................................................................................................................................. 9

3.8 Constant light parameters ........................................................................................................................................................... 10

3.9 Constant light parameter - Dead zone .......................................................................................................................................... 11

4. Functional blocks ............................................................................................................................................................................... 11

4.1 Light control channel ................................................................................................................................................................. 11

4.2 HVAC channel ............................................................................................................................................................................ 12

4.3 Brightness - Threshold switch ..................................................................................................................................................... 13

4.4 AD calibration value .................................................................................................................................................................... 13

4.5 Objects for constant light control ................................................................................................................................................. 14

5. Program version 2.7 .......................................................................................................................................................................... 15

5.1 Overview of changes .................................................................................................................................................................. 15

5.2 Communication objects ............................................................................................................................................................... 15

5.3 Parameters ................................................................................................................................................................................ 16

English ....................................................................................................................................................................................... 2

Français .................................................................................................................................................................................... 18

Deutsch ..................................................................................................................................................................................... 36

2524X_2525XCH_ETS_description EN

2524X/2525XCH

1. FUNCTIONAL DESCRIPTION

The SWISS GARDE 300P KNX/KLR Type No. 25240 D (CH) is a 4 channel presence detector for wall mount indoor installation.

The SWISS GARDE 300P KNX/KLR Type No. 25241, 2542 are for outdoor wall mount installation with enhanced temperature range. They provide IP55 protection.

The device is based on a modern 16-bit microcontroller with internal ﬂash memory and an integrated KNX/EIB bus coupler.

Three pyro detectors and a high resolution lens can detect the smallest motions.

The 3 PIR sensors can be activated individually or in groups.

An integrated light sensor with linear output measures brightness. Its built-in optical filter has a spectral response similar to that of the human eye.

All models cover can be configured as a master or as a secondary device.

The presence detector has a 2-channel constant light controller (CLC) with a parametrable offset between -50% to +50%. There is an additional light channel output for switching, dimming or scene selection.

An additional HVAC channel can be used for HVAC controls, alarm systems or presence detection.

With the standard KNX bus, all switching and control functions can be easily programmed and executed.

The application description is valid for devices with the program version 2.4. Functional enhancements and changes from program version 2.7. are described in the chapter 5.

Art.-Nr. 25241

Art.-Nr. 25240 CH

1.1. Model Overview

Description colour E-No. EAN-Nr. Art.-Nr

Swiss Garde 300 Presence KNX/KLR UP white 305 401 209 3505100252405 25240 CH

Swiss Garde 300 Presence KNX/KLR UP white 3505100252405 25240 D

Swiss Garde 360 Presence KNX/KLR IP55 UP white 305 401 309 3505100252412 25241

Swiss Garde 360 Presence KNX/KLR IP55 AP white 205 401 309 3505100252429 25242

Swiss Garde 300 presence detector KNX/KLR, STANDARDdue Ø50 white 305 401 219 3505100252511 25251 CH

Swiss Garde 300 presence detector KNX/KLR, STANDARDdue Ø50 black 305 401 819 3505100252528 25252 CH

1.2. Dimensions

90 mm

15 mm

15 mm 48 mm

13 mm

30 mm 11 mm

86 mm

13 mm

30 mm 11 mm

13 mm

30 mm 11 mm

86 mm

30 mm 54 mm

86 mm

Art.-Nr. 25251CH/25252CH

Art.-Nr. 25241 Art.-Nr. 25242

Art.-Nr. 25240 CH

305 401 209

EN 2524X_2525XCH_ETS_description

2524X/2525XCH

2. COMMUNICATION OBJECTS *

input objects

output objects

Object Function link application with Bit/Byte

0 Output - light (preset dimming) light group actuator 1 byte

0Output - light (switching) light group actuator. 1 bit

0Output - light (scene) light group actuator 1 bit

1Input external switch / status - light

(switching)

KNX switch, touch display, logic 1 bit

2Input external motion - light (switching) Output - light for secondary unit (object 0) 1 bit

3Input - light (forced control) • External logic module 2 bit

3Input - light (lock) KNX switch, touch display, logic module 1 bit

4Output - HVAC (switching) • Actuators for HVAC devices such as heating, ventilation and air conditioning

• Control of alarm logic modules

• Presence function

1 bit

5External switch / status - HVAC (switching) KNX switch, touch display, logic 1 bit

6External motion - HVAC (switching) Output HVAC for secondary unit (output object 4). 2 byte

7Input - HVAC (forced control) External logic module 2 bit

7Input - HVAC (lock) KNX switch, touch display, logic 1 bit

8Threshold switch brightness (switching) Logic, actuator 1 bit

9Brightness (lux value) Logic, touch display 2 byte

10 AD calibration value Read out and then set manually for calibration procedure 2 byte

16 Constant light control, switch on/off KNX switch , logic 1 bit

17 Constant light control, dimming relative 4 bit dimming object from KNX switch for ON/OFF, dimming up and down, touch display 4 bit

18 Constant light control, preset dimming Logic module 1 byte

20 Constant light control, forced control KNX button, logic 1 bit

21 Constant light control, scene selection Logic module 1 byte

22 Constant light control, channel 1 - output Dimming actuator for light group 1 1 byte

23 Constant light control, channel 2 - output Dimming actuator for light group 2 1 byte

24 Light - standby Switching of standby value sets 1 bit

* Communication objects program version v2.4

3. PARAMETERS

To set the parameters, the SG360P KNX/KLR RA/EA motion detector should be highlighted in the conﬁguration or operating mode and the command Parameter be selected from the Edit menu item or via the context menu

(right mouse click). The Edit parameter... window will open with multiple tabs.

3.1. General

Type of detector The function of the detector is set as a master or secondary (slave) device

Delay time for forced control mode The value “OFF” or a time of 5 min to 9 hrs can be selected in the reset time forced control menu. This parameter deﬁnes the time delay for the detector to reset to AUTO

mode, after an OFF or ON command has been executed.

2524X_2525XCH_ETS_description EN

2524X/2525XCH

3.1.1. Secondary Detector Mode

Secondary Detector Mode

(

Slave Mode

)

The secondary detector mode can be reached in the menu General: click the type of detector as slave and the menu slave mode appears. The delay time of the

secondary unit is fixed to 30 sec.

LED green For testing purposes, the indication LED for motions can be activated.

Value of object Selectable ON or OFF

Idle time after switch off Can be set from 1 sec to 60 sec

Default value is 5 sec

Cyclical transmission We recommend retriggering the Master unit cyclically when operating in the Master/Secondary Detector mode.

The interval time for cyclical transmission can be set from 1 second to 4 hours.

Default value is 30 sec

PIR evaluation

Active sensors The 3 PIR sensors can be enabled individually or in groups. The numbers 1, 2, and 3 correspond to positions 1, 2, and 3 as shown in the illustration (§3.6).

Sensitivity setting The sensitivity can be adjusted from 1 to 10.( 1 = min, 10 = max)

The default value is 5.

3.2. Light - Switch / Dimming / Standby values

Operating mode of the detector Sets the operating mode to fully or semi-automatic.

Green LED This LED may ﬂash once after each motion detection or remain off

Delay time The delay time for the light channel can be set from 1 sec to 4 hrs

Brightness below which sensor is active Set lighting value from 10 Lux to 2000 Lux and always.

Important: If the light channel always remain active ( even with values > 2000 lux,the parameter must be to always.

Brightness above which lighting is turned

off

Brightness threshold (lux) for immediate switch-off, even if delay time has not yet elapsed. Default value is OFF.

Forced control object or disabled object This will set object 3. See description of object 3: force control mode – lock mode (§3.6)

EN 2524X_2525XCH_ETS_description

2524X/2525XCH

If locked object = 0 Selects an action to be executed after reception of a 0 command

If locked object = 1 Selects an action to be executed after reception of a 1 command

Object type for output - light This will deﬁne object 0. The following options are available: switching, dim completely, scene selection

Object value for ON when object type is:

light = switching

light = dimming

light = scene

Select ON or OFF (ON is default value)

Select preset dim value from 0% to 100%

Select scenes from 1…32

Object value for OFF when object type:

light = switching

light = dimming

light = scene

Select ON or OFF (OFF is default value)

Select preset dim value from 0% to 100%

Select scenes from 1…32

Transmission conditions for switching

object

Transmission ﬁlter for output object 0: Output - Light - Switching

Selection: ON and OFF; neither ON nor OFF; only ON; only OFF

Transmission conditions for external

switch

Selection: ON and OFF; neither ON nor OFF; ON only; OFF only

Idle time after switch off Can be set from 1 sec to 60 secs

Applications:

Prevention off bus trafﬁc excess

Prevention of erroneous lighting restart if:

• light bulbs are cooling down

• room is deserted after switching off with a KNX switch.

Cyclical transmission If the light channel is in switching mode, it is possible to cyclically transmit the “ON” mode.

The interval time for cyclical transmission can be set from 1 second to 4 hours.

3.2.1. Light – Preset Dimming

Object type for output-light Preset dimming

This setting enables the standby light function. The Standby value option appears in the Light menu.

3.2.2. Light - Standby parameters

2524X_2525XCH_ETS_description EN

2524X/2525XCH

Standby values Toggles the orientation light function between active and inactive

Standby time 1 Set orientation light 1 duration time (seconds, minutes, hours).

Standby value 1 Set light intensity in % (0...100%)

Standby time 2 Set orientation light 2 duration time (seconds, minutes, hours).

Standby value 2 Set light intensity in % (0...100%)

Standby light

If the light channel is set to preset dimming, a new menu will appear to enable the standby functionality.

There are 2 parameters for both the duration time and the light intensity (%) of the standby operation.

After the regular duration time has elapsed the standby light will turn on. With object 24 the user will then be able to select one of two presetable parameter pairs. If the object value is 0 or there was no command received

yet, value pair 1 is enabled. A 1 command value will trigger pair 2.

After standby has elapsed, an OFF command will be sent on the light channel.

The motion detector will return to regular mode and standby mode will be reset.

Lock commands and forced control commands will always reset standby mode immediately.

3.3. HVAC

All parameters are identical to those of the light channel with the exception of:

Number of monitoring time windows The number of monitoring time intervals can be set from 1 to 32.

Duration of monitoring time window Adjustable from 1 s to 30,000 s (8.33h)

Note! The correct setting for fastest response of the HVAC channel is:

Number of monitoring time windows: 1

Duration of monitoring time window: 1 second

Presence function

with HVAC channel

The above parameters should be used for the presence function (the presence signal is independent from the ambient lighting brightness!)

3.4. Brightness / threshold switch / Value calibration

EN 2524X_2525XCH_ETS_description

2524X/2525XCH

The parameters for object 8 (Brightness threshold switch, 1 bit) and object 9 (Brightness value, 2 bytes) can be set in the Brightness / Threshold menu.

Transmission of the lux value in case of

change of

This parameter allows the lux value + change to be sent via object 9 (brightness value) if the set threshold is exceeded. Values from 10 lux up to 1800 lux and “OFF” can be

set. The set value of change refers to the set threshold.

Cyclical transmission of the light value Values from 5 seconds to 30 minutes and „OFF“ can be set.

Lux value of the threshold for switching Can be set from 10 lux to 2000 lux

Hysteresis Can be set from 5 lux to 200 lux

Object value for ON Selection: “ON” or “OFF”

Object value for OFF Selection: “OFF” or “ON”

Transmission ﬁlter Selections: "ON and OFF"; "neither ON nor OFF"; "ON only"; "OFF only"

3.5. Brightness value calibration

Calibration “NO”: Factory calibration is enabled (default value)

Reset to factory calibration: This is possible at any time with the setting “NO” and thereafter the reprogramming of the detector.

“YES”: This option opens the following two additional windows:

AD calibration value Read AD calibration value (at object 10) in the ETS and enter it in the window.

Attention: use type 7.001 unsigned 2 byte counter in the read/send value menu! The AD value read-out then appears in the Value received menu (e.g. 739 pulses).

Lux value Measure reference brightness with lux meter and enter corresponding value.

See also description of “AD calibration value” on §4.4 for further details.

3.6. PIR evaluation

2524X_2525XCH_ETS_description EN

2524X/2525XCH

Active sensors The 3 PIR sensors can be enabled individually or in groups. The numbers 1, 2, and 3 correspond to positions 1, 2, and 3 as shown in the illustration below.

Sensitivity setting The sensitivity can be adjusted from 1 to 10. (1 = min, 10 = max)

The default value is 5.

Numbering of the PIR sensors

LUX sensor

LED motion ﬂashes once with each detection

LED programming glows upon pressing

programming button

The PIR sensors 1, 2 and 3 can be enabled individually or in groups of two.

The 3 positions of the pyro detectors are visible in the above illustration.

3.7. Constant light control

EN 2524X_2525XCH_ETS_description

2524X/2525XCH

3.7.1. Constant light scenes

3.8. Constant light parameters

Constant light controller This parameter enables or disables the constant light controller.

Channel 2 for constant light control Channel 2 can be enabled for constant light control

Active/inactive Via the output object 23 a conﬁgurable value with a ﬁxed offset can be transmitted

Preset setpoint The preset setpoint in lux for constant light control can be preset in the ETS. It can also be changed via objects 17 and 18 (constant light - dimming relative and

constant light - dim completely).

Transmit difference This parameter (from 1% to 100%) deﬁnes the tolerance window to be exceeded in order to send a new brightness control value.

Switching constant light control with Switching constant light control ON/OFF can be done using three different sources:

By object 16, presence detection on the light channel or presence detection on the HVAC channel.

Time interval for cyclical transmission Deﬁnes the cycle time interval with which the last brightness value is repeated, even if it has not exceeded the tolerance window.

Cyclical transmission can also be disabled.

Switch on brightness value The switch on value for the lighting can be set from 1% to 100 %.

Switch on timeout This parameter deﬁnes the initial time delay before constant light control is started.

Offset for channel 2 * The offset range for channel 2 can be set from -50%, 0% to +50%.

Force control during switch-on This parameter allows the constant light controller function to be set to: no reaction, minimum brightness, maximum brightness

Force control during switch-off This parameter allows the constant light controller function to be set to: no reaction, minimum brightness, maximum brightness

Time for relative dimming This parameter allows the relative dimming time to be set. This will inﬂuence the dimming soft control.

Take over set point after This parameter allows setting the time delay after which a new setpoint will be recognized and stored in the RAM memory.

Changed setpoint to ﬂash memory This parameter allows a new set point to be written to the ﬂash memory.

Keep changed set point Here at Yes the changed value is stored in the RAM .

Attention: now corresponds to the new nominal value of the last new dimmed brightness !

Scene Various lux values can be set as light scenes (light moods).These can be enabled through object 21 as well.

Dead zone The dead zone is an area within which the actual light value can change without generating new control commands. The default value for the dead zone is 2.

The lux value tolerance of the dead zone can be extracted from the table below.

Example:

Dead zone value = 2

Brightness = 500 lux

The resulting tolerance is: +/- 24 lux

This means that the actual value can change from 476 lux to 524 lux without sending new control inputs to the actuator.

* In addition to the previous constant light control channel 1 (Object 22 ) there is a second constant light control channel 2 (Object 23 ). The control signal of channel 1 ± offset value is sent to the dimming actuator

for light channel 2. Internally, the control range has been extended to ± 150% in order to maintain a reasonable control range at the limits.

That means: Offset at -50%, darkness: FF (=100%) is sent to both objects. Internally, object 1 is at 150% and object 2 at 100%. If the ambient brightness now increases, object 1 remains at 100% (150% - x) and object

2 is regulated downwards (150% - 50% - x). If the regulation now drops below 100%, object 1 will also be visibly smaller on the bus, e.g. 73%, object 2 23%. Object 1 is then regulated down to 0 and object 2 is set to

the minimum value of 50%. The values for transmission difference and cyclical transmission are taken from the once off available parameters.

2524X_2525XCH_ETS_description EN

2524X/2525XCH

3.9. Dead zone/Brightness correlation

Brightness in lux, +/- lux tolerance (dead band)

Dead zone

12345678910

Brightness 100 2 5 7 10 12 15 17 20 23 26

200 5 9 14 19 24 30 35 40 46 52

300 7 14 21 29 37 44 52 61 69 78

400 9 19 29 39 49 59 70 81 92 104

500 12 24 36 48 61 74 87 101 115 129

600 14 28 43 58 73 89 105 121 138 155

700 16 33 50 68 85 104 122 142 161 181

800 19 38 57 77 98 119 140 162 184 207

900 21 42 64 87 110 133 157 182 207 233

1000 23 47 72 96 122 148 175 202 230 259

1100 26 52 79 106 134 163 192 222 253 285

1200 28 57 86 116 146 178 210 243 276 311

1300 30 61 93 125 159 193 227 263 299 337

1400 33 66 100 135 171 207 245 283 322 362

1500 35 71 107 145 183 222 262 303 345 388

1600 37 75 114 154 195 237 280 324 368 414

1700 40 80 122 164 207 252 297 344 391 440

1800 42 85 129 174 220 267 315 364 414 466

1900 44 90 136 183 232 281 332 384 438 492

2000 47 94 143 193 244 296 350 405 461 518

4. FUNCTIONAL BLOCKS

The functionality of the presence detector can be split up into the following blocks:

• Motion detection

• Brightness measuring

• Light control channel Switching

• Light control channel preset dimming with optional standby light function

• HVAC control channel (with presence function)

• Lighting dependent threshold switch

• 2 channel constant light control

The motion detector and the brightness sensor (lux) each work independently on the light channel and the HVAC channel.

The constant light controller receives the actual brightness value from the Lux sensor. The controller can

be switched on/off by a command via object 16 or triggered by motion detection on the light or HVAC channel.

After switching or recovery of the KNX bus voltage, the presence detector usually generates a switch-on procedure.

4.1. Light control channel

The light control channel has two operating modes that can be selected via the detector operating mode parameters.

The possible settings are:

• fully-automatic

• semi-automatic

The differences between the fully-automatic and semi-automatic modes are:

• fully-automatic mode has three operating conditions: ready, active and passive

• semi-automatic mode has two operating conditions: ready and active

• semi-automatic mode does not switch the light on after motion has been detected.

Lighting can only be switched on manually by an external KNX switch.

4.1.1. OBJECT 0 OUTPUT – LIGHT – SWITCH

Output 1 bit

After each detected motion this output sends an “ON” command and starts the delay timer

The delay time can be set with parameter delay time from 1 second to 4 hours.

At the end of the programmed time interval an “OFF” command is sent to the output (object 0).

4.1.2. OBJECT 0 OUTPUT – LIGHT – COMPLETE DIMMING

Output 1 byte

This mode sends preselected dim values (0% to 100%) to the output for objective value for ON and for objective value for OFF respectively.

4.1.3. OBJECT 0 OUTPUT – LIGHT – SCENE

Output 1 byte

For the Objective value for ON or Objective value for OFF one of 32 scenes can be selected respectively.

EN 2524X_2525XCH_ETS_description

2524X/2525XCH

4.1.4. OBJECT 1 EXTERNAL SWITCHING / STATUS - LIGHT - SWITCH

Input 1 Bit

Input object 1 external switch / status can be used in two different ways:

• As an input for an external push button that directly switches on the light

• As an input for monitoring the status or the input of an actuator

In both cases, a received telegram „ON“ sets the detector to the ON state and an „OFF“ telegram to the ready state.

Whether commands for ON or OFF will be sent during the transitions depends on the parameter sending conditions for external push button.

After having received an ON command, the follow up timer starts as if a motion had been detected.

Lighting is subsequently switched off again.

After having received an OFF command the detector remains in its passive status during which it will not detect any motion. After having passed the idle time after switch off, the detector is ready again.

The idle time after switch off can be programmed in the light menu.

4.1.5. OBJECT 2 EXTERNAL MOVEMENT - LIGHT - SWITCH

Input 1 Bit

Additional (secondary) detectors can be connected through Object 2 “external movement - light – switching”.

The received signal from external presence detectors is processed the same as if from its own detector and works in parallel.

Object 2 is used to set up a Master-Secondary detector configuration as follows:

Secondary devices: Connect all outputs of the secondary devices ( object 0 ) to the input external movement-light-switching ( object 2 ) of the master device.

4.1.6. OBJECT 3 INPUT - LIGHT - FORCED CONTROL / LOCK

Input 2 Bit

The meaning of this object is deﬁned by the Light forced control object or disabling object parameter.

Forced control object:

Object 3 when used as forced control object has 3 values which can be received by a 2 bit command:

1. Forced control object ON (control = 1, value = 1)

An ON command is sent unconditionally to the output – light (object 0).

The follow up timer is disabled and the timer release time starts.

If after having terminated the release time and no further command is sent to the forced control object, normal operation is resumed.

2. Forced control object OFF (control = 1, value = 0)

An OFF command is sent unconditionally to the output – light (object 0).

The delay timer is disabled and the timer release time starts.

If after having terminated the release time and no further command is sent to the forced control object, normal operation is resumed.

3. Forced control object auto (control = 0, value = 0)

Normal operation is resumed immediately.

Locked object:

Object 3 when used as locked object has 2 values which can be received by a 1 bit command 0 and 1:

The response to a switch command on this object is controlled by two more parameters:

Light if locked object = 0, and Light if locked object = 1,

Both parameters can specify one of the following commands:

• forced control ON

• forced control OFF

• automatic

• lock (actual state)

• do nothing

Note: Incorrect settings of parameters such as: locked object, lock at 0 and no action at 1 and release time restraint OFF can completely inactivate the correct function of the presence detector.

4.2. HVAC channel

Output 1 bit

The HVAC channel has the same objects and the same operating modes as the light channel. It works the same way as the light channel as well.

The motion detection function, however, has been expanded and substituted by a “longer presence detection”. This is done by setting several equally long monitoring time windows. At least one motion

detection must occur during each time slot.

The parameters are:

• number of monitoring time windows

• length of monitoring time window (s)

Presence function

The HVAC output can be used as a presence detection. To activate this, the number of observation time windows must be set to 1 and the length of the observation time window set to 1 second. The presence

signal is independent of the ambient light level.

4.2.1. OBJECT 4 OUTPUT – HVAC – SWITCH

Output 1 bit

Object 4 “Output - HVAC - Switch” is similar to object 0 “Output - light - switch” but has additional functions (see HVAC parameters, page 10).

4.2.2. OBJECT 5 EXTERNAL SWITCHING / STATUS - HVAC

Input 1 Bit

Object 5 “External switching / status - HVAC” is identical to object 1 “External switching / status - light”.

4.2.3. OBJECT 6 EXTERNAL MOVEMENT - HVAC

Input 1 Bit

Object 6 “External movement - HVAC - switch” is identical to object 2 “External movement - light - switch”.

2524X_2525XCH_ETS_description EN

2524X/2525XCH

4.2.4. OBJECT 7 INPUT - HVAC - FORCED CONTROL

Input 2 Bit

Object 7 “Input - HVAC - forced control” is identical to object 3 “Input - light - forced control”.

4.2.5. OBJECT 7 INPUT - HVAC - DISABLE

Input 1 Bit

Object 7 “Input - HVAC - disable” is identical to object 3 “Input - light - disable”.

4.3. BRIGHTNESS THRESHOLD SWITCH

This block has two output objects: Threshold switch and brightness value

4.3.1. OBJECT 8 THRESHOLD SWITCH BRIGHTNESS - SWITCHING

Output 1 bit

Output object 8 sends an “ON” if the measured brightness is greater than the Value for switching the threshold value switch parameter. If the measured brightness drops below the Switch-on threshold value – (minus) the

Hysteresis parameter, an “OFF” is transmitted.

4.3.2. OBJECT 9 BRIGHTNESS VALUE

Output 2 bytes

Output object 9 sends the current measured brightness value in lux. The transmission is triggered by changes that are greater than the parameter Transmission of the light value in case of a change of or cyclically with the

time stipulated for Cyclical transmission of the light value.

If the cycle time is set to “OFF” there will be no cyclical transmission.

4.4. AD calibration value

Output 2 bytes

Object 10 is not transmitted autonomously. It can only be read. Its unsigned 16 bit value represents the momentary value of the AD converter for the brightness measurement.

The brightness measurement can be calibrated as follows:

• Measure the incident light - on a desktop for example - with an external lux meter. This represents

the reference lux value.

• Read out the AD calibration value (communication object 10) in the ETS.

Note: In the menu Read/send value, use type 7.001 unsigned 2 byte counter!

The AD value read then appears in the Value received menu as 739 pulses, for example.

• With full access, enter the two values Lux value and AD calibration value as parameters.

EN 2524X_2525XCH_ETS_description

2524X/2525XCH

4.5. OBJECTS FOR CONSTANT LIGHT CONTROL

4.5.1. OBJECT 16 CONSTANT LIGHT - SWITCH ON/OFF

Input 1 bit

This input allows the constant light controller to be switched ON and OFF (Object).

Alternatively the constant light controller can be activated by motion detection on the light or the HVAC channel.

4.5.2. OBJECT 17 CONSTANT LIGHT - RELATIVE DIMMING

Input 4 bit

Using this object, the current value is changed with relative dimming steps of 1%.

Using a KNX push button, light can be dimmed and set to a new brightness level.

The new light value can then be displayed in Lux on a KNX touch panel through object 9: brightness value.

Important: In the menu constant light take over set point after you can deﬁne the period during which the controller will remain switched off. After this interval, the new value is written to the RAM

(not to the ﬂash memory)!

Note: This new target value remains stored in RAM as long as there are people present in the scanned area. After switching the light channel off and back on again, the set point stored in ETS is adopted once again.

If the newly changed set point are deﬁnitely taken over, set the parameter Keep changed set point to YES (see also section 3.8 Constant light parameter page 18)

4.5.3. OBJECT 18 CONSTANT LIGHT – PRESET DIMMING

Input 1 Byte

With this object the user can deﬁne a new dim set point in % over the bus.

4.5.4. OBJECT 20 CONSTANT LIGHT - FORCE CONTROL

Input 1 bit

In accordance to the parameters force output at ON and force output at OFF, various options can be selected: no reaction, minimum brightness, maximum brightness

4.5.5. OBJECT 21 CONSTANT LIGHT - SCENE

Input 1 byte

Scene selection input. 8 adjustable scenes can be selected via ETS.

This object has no switch function but only changes the brightness setpoint values.

4.5.6. OBJECT 22 CONSTANT LIGHT - OUTPUT CHANNEL 1

Output 1 byte

This is the constant light control signal (% brightness) for the dimming actuator of lighting 1

4.5.7. OBJECT 23 CONSTANT LIGHT - OUTPUT CHANNEL 2

OUTPUT 1 byte

This is the constant light control signal for the dimming actuator of lighting 2.

The lux value is equal to channel 1 +/- offset.

2524X_2525XCH_ETS_description EN

2524X/2525XCH

5. PROGRAMMVERSION 2.7

With the program version 2.7, the function possibilities of the presence detector - series Swiss Guard 360P KNX / KLR RA / EA expanded and existing features of program version 2.4, have been supplemented respectively adapted.

The standard values (default values) of the parameters compared to the settings in version 2.4 are partially modiﬁed.

These settings allow a simple and safe functionally check (initial start-up ) of the presence detector .

Older devices of software version 2.4 can also be programmed with the program version 2.7 ( backward compatibility ) .

However, supplemented functions and the additional communication objects are not all

supported.

5.1. Overview of the changes:

see 5.2.0

see 5.2.1

see 5.2.2

see 5.3.1

see 5.3.2

see 5.3.3

see 5.3.4

• Forced control Secondary detector-Mode

• Parameter changes via communication objects

• Dimming function with constant light control (clc)

• Power on characteristics

• Automatic lighting OFF threshold

• Delay time in semi-automatic mode

• Standby-function

• Light sensor adaption see 5.3.5

5.2. Communication objects