I N S T A L L A T I O N I N S T R U C T I O N S
Vibration Isolation Wall Mount Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PACVISO1
PACVISO1 Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
Chief® is a registered trademark of Legrand AV Inc.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory. The wall to which the accessory is being attached
may have a maximum drywall thickness of 5/8” (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this accessory does not exceed:
• Wood/Steel Stud: 125 lbs (56.7 kg)
• Drywall-only: 75 lbs (34.0 kg)
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this accessory outdoors.
IMPORTANT ! :
The PACVISO1
accessory
is designed to be
mounted to an:
• 2" x 4" wood studs (16" on center) wall covered in 1/2"
to 5/8" drywall; or
• 2" x 4"-25ga minimum steel stud wall covered in 1/2" to
5/8" drywall; or
• drywall-only wall (1/2" min. drywall thickness)
IMPORTANT ! : The PACVISO1 accessory is only
compatible with the RMF3 FIT-series wall mount
--SAVE THESE INSTRUCTIONS--
Installation Instructions PACVISO1
3
DIMENSIONS
DIMENSIONS: INCHES
[MILLIMETERS]
PACVISO1 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions PACVISO1
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/2" (12.7mm) #2
1/2" (12.7mm)
7/16" (11.1mm)
1/2" (12.7mm)
7/16" (11.1mm)
7/32" (5.5mm)
A (2)
Vertical bracket
Toggler Anchor Kit
Hardware Pack
B (4)
Stud Plate
C (2)
Top Cap
D (1)
Lower Bracket
E (1)
Lower Wall Bracket
F (4)
1/4-20 x 1-3/4"
G (4)
1/4"
H (4)
Snaptoggle
J (4)
10-24 x 3/8" K (4)*
1/4" x 2-1/2"
L (4)
Lock nut
M (4)
Spacer
N (4)
1/4"
(For drywall/steel Stud
installations only)
* For wood stud
installations only
PACVISO1 Installation Instructions
6
Assembly
Locate Mounting Site
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! It is the installers
responsibility to make certain the structure to which the
mount is being attached is capable of supporting five times
the combined weight of all components attached to mount.
•PACVISO1: 125 lbs (56.7 kg)/ 75 lbs (34.0 kg)
Installing Lower Wall Bracket
The PACVISO1 mount is designed to be mounted to:
• a 2" x 4" wood studs (16" on center) wall (min. 1/2",
max. 5/8" drywall thickness); or
• a steel stud (16" on center) wall (min. 1/2", max. 5/8"
drywall thickness); or
• a drywall-only wall (minimum thickness of 1/2")
1. Place the lower wall bracket (E) on the wall in the desired
location, making sure both mounting slots are positioned
over a wall stud. Hold the bracket level and mark the
locations of both mounting slots. (See Figure 1)
2. Remove the lower wall bracket (E) from the wall and drill
one pilot hole (7/32" wood stud, 1/2" steel stud) at each
location. (See Figure 1)
IMPORTANT ! : Refer to Fastener Installation Methods
(located in Appendix at end of Installation Instructions)
for details on installing product into various wall types.
3. Replace lower wall bracket (E) on wall and install using:
• Wood studs: Two 1/4" x 2-1/2" lag bolts (K) and
two 1/4" washers (N). (See Figure 1)
• Steel stud/drywall-only: Two 1/4-20 x 1-3/4" (F)
and two 1/4" washers (G). (See Figure 1)
Figure 1
4. Install two vertical brackets (A) to the lower bracket (D)
using four 10-24 x 3/8" Phillips screws (J). (See Figure 2)
Figure 2
5. Install the display wall mount bracket to the assembled
frame using four stud plates (B), four spacers (M), four 1/4"
washers (N), and four lock nuts (L). (See Figure 3)
Figure 3
6. Insert bottom edge of the assembled frame into lower wall
bracket (E) at an angle. Once in place, rotate the upper
edge of the frame towards the wall until frame rests flat
against the wall. (See Figure 4)
NOTE: Make sure lower bracket (D) is completely seated into
the lower wall bracket (E).
1
2
X2
X2
3
(K) x 2
(G) x 1
(N) x 1
(E) x 1
(N) x 1
(G) x 1
(F) x 2
4
(L) x 4
(A) x 2
(D) x 1
5
(L) x 4
(N) x 2
(N) x 2
(M) x 2
(M) x 2
(B) x 4
Installation Instructions PACVISO1
7
Figure 4
7. Slide two top caps (C) over the upper ends of the vertical
brackets (A). (See Figure 5)
NOTE: Top caps (C) must be flush to the surface of the wall
while seated against the vertical brackets (A).
Figure 5
8. Mark the locations of the mounting slots in both top caps
(C), then remove the caps from the vertical brackets (A).
9. Drill one pilot hole at each marked location. (See Figure 6)
10. Replace top caps (C) and install using two 1/4" x 2-1/2" lag
bolts (K) and 1/4" washers (N). (See Figure 6)
Figure 6
APPENDIX
Fastener Installation Methods
Wood Stud
IMPORTANT ! : See Site Requirements for Wood or
Steel Stud section before proceeding with installation to
ensure installation site meets requirements! The drywall
must have a thickness of 1/2" - 5/8"!
11. Use one 1/4" x 2-1/2" lag bolt (K) and one 1/4" washer (N)
through product and into pilot hole. (See Figure 20)
12. Repeat for remaining pilot holes.
Figure 7
6
6
(E) x 1
(D) x 1
(C) x 2
7
(A) x 2
(K) x 2
10
(N) x 1
(N) x 1
x 2
89
(C) x 1 (C) x 1
(K) x 4
1
2
(N) x 4
PACVISO1 Installation Instructions
8
Steel Stud/Drywall Only
IMPORTANT ! : See Site Requirements for Wood or
Steel Stud section before proceeding with Steel Stud or
Drywall Only installation to ensure installation site meets
requirements! The drywall must have a minimum
thickness of 1/2"!
1. Hold metal channel on snaptoggle (H) flat alongside plastic
straps and slide channel through hole. (See Figure 8)
Figure 8
2. Holding plastic straps on snaptoggle (H), pull anchor away
from wall until channel rests flush behind wall making sure
anchor channel is positioned vertically on drywall, or steel
stud (if present). (See Figure 9)
3. Slide plastic cap on snaptoggle towards wall until flange of
cap is flush with wall. (See Figure 9)
Figure 9
4. Snap off plastic straps on snaptoggle at wall by pushing side
to side, snapping off straps level with flange of plastic
cap.(See Figure 10)
Figure 10
5. Line up snaptoggle with attachment point.
6. Insert 1/4-20 x 1-3/4" Phillips pan head screw (F) through
1/4" washer (G), corresponding mounting hole in wall
bracket and into anchor (H), and tighten until flush against
wall bracket. DO NOT over-tighten! (See Figure 11)
Figure 11
Site Requirements for Wood or Steel Studs
IMPORTANT ! : Steel Studs ONLY: If back side of wall
is unfinished, drywall must be installed to a minimum of
one stud left and right of the stud(s) being used to install
the mount. Drywall must be secured to studs with screws
a maximum of 12" (305mm) apart down center of stud.
NOTE: Steel stud type and structural strength must conform to
the North American Specification for the design of
Cold-Formed Steel Structural Members [362 S 125 18,
C-Shaped, S-stud Section]
Figure 12
Drywall
Plastic cap
(H)
Drywall
Plastic cap
Steel stud (if present)
(side view) Anchor metal channel
Plastic straps
Drywall
Anchor metal channel
Plastic cap
Steel stud (if present)
(side view)
Anchor metal channel
(F) x 4
(G) x 4
Wall bracket
Steel stud (if present)
Drywall
6
(side view)
There must be a minimum of 1-7/8"
(48mm) clearance inside wall
Wood stud (2 x 4)
Drywall
1/2" minimum
Drywall Thickness
(Both Sides of Stud)
Drywall-covered
Studs
(2 x 4 / 25ga min.)
or Steel stud*
Installation Instructions PACVISO1
9
PACVISO1 Installation Instructions
10
PACVISO1 Installation Instructions
11
PACVISO1 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003345 Rev01
2023 Legrand | AV
www.legrandav.com
04/2023
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
dans d''autres langues
Documents connexes
-
Chief FHBO5169 Guide d'installation
-
-
-
-
-
-
-
Chief RSMEU spécification
-
-