Toro 42in Bagger, eTimecutter Riding Mower Manuel utilisateur

Form No. 3466-378 Rev A

42in or 54in Bagger

79841 , 79851

Heckfangsystem (107 cm oder 137

cm)

79841 , 79851

Système de ramassage de 107 cm ou

137 cm

79841 , 79851

Grasvanger van 107 cm en van 137

cm

79841 , 79851

*3466-378*

Form No. 3466-364 Rev B

42in or 54in Bagger

eT imecutter Riding Mower

Model No. 79841 —Serial No. 400000000 and Up

Model No. 79851 —Serial No. 400000000 and Up

Operator's Manual

Introduction

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

Whenever you need service, genuine parts, or

additional information, contact an Authorized Service

Dealer or Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

g466960

Figure 1

1. Model and serial number location

Model No.

Serial No.

This manual uses 2 words to highlight information.

Important calls attention to special mechanical

information and Note emphasizes general information

worthy of special attention.

The safety-alert symbol ( Figure 2 ) appears both in

this manual and on the machine to identify important

safety messages that you must follow to avoid

accidents. This symbol will appear with the word

Danger ,W arning , or Caution .

•Danger indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury .

•W arning indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury .

•Caution indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury .

sa-black

Figure 2

1. Safety-alert symbol

Original Instructions (EN)

Printed in the USA

*3466-364*

W ARNING

CALIFORNIA

Proposition 65 W arning

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1 Preparing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Removing the Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3 Installing the W eights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4 Installing the Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5 Installing the Lower Bagger Mount and

Pivot Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

6 Installing the Hood Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7 Assembling the Bagger T op . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

8 Installing the Bagger T op Assembly . . . . . . . . . . . . . . . . 20

9 Installing the Baf e (54in Decks

Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

10 Installing the Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

1 1 Installing the Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

12 Connecting with the Discharge

T ube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Emptying the Grass Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Clearing Obstructions from the Bagger . . . . . . . . . . . . . 27

Removing the Bagger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Recommended Maintenance Schedule(s) . . . . . . . . . . . 30

Inspecting the Bagger Attachment . . . . . . . . . . . . . . . . . . . . 30

Inspecting the Mower Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Cleaning the Bagger Attachment . . . . . . . . . . . . . . . . . . . . . . 30

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Storing the Bagger Attachment . . . . . . . . . . . . . . . . . . . . . . . . . 31

Safety

•Become familiar with the safe operation of the

equipment, with the operator controls, and safety

signs.

•Use extra care with grass catchers or other

attachments. These can change the operating

characteristics and the stability of the machine.

•Follow the manufacturer's recommendations

for adding or removing wheel weights or

counterweights to improve stability .

•Do not use a grass catcher on steep slopes. A

heavy grass catcher could cause loss of control

or overturn the machine.

•Slow down and use extra care on hillsides. Be

sure to travel in the recommended direction on

hillsides. T urf conditions can af fect the stability of

the machine. Use extreme caution while operating

near drop-of fs.

•Keep all movement on slopes slow and gradual.

Do not make sudden changes in speed, direction,

or turning.

•The grass catcher can obstruct the view to the

rear . Use extra care when operating in reverse.

•Use care when loading or unloading the machine

into a trailer or truck.

•Never operate with the discharge deector raised,

removed or altered, unless using a grass catcher .

•Keep hands and feet away from moving parts. Do

not make adjustments with the machine running.

•Park the machine on level ground, disengage the

drives, and shut of f the machine before leaving

the operator's position for any reason including

emptying the grass catcher or unclogging the

chute.

•If you remove the grass catcher , be sure to install

any discharge deector or guard that might have

been removed to install the grass catcher . Do not

operate the mower without either the entire grass

catcher or the grass deector in place.

•Do not leave grass in the grass catcher for

extended periods of time.

•Grass catcher components are subject to wear ,

damage and deterioration, which could expose

you to moving parts or allow objects to be thrown.

Frequently check components and replace with

the manufacturer's recommended parts, when

necessary .

•Do not use the machine as a towing vehicle.

2

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal109-6809

109-6809

1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s)

from the bagger . Do not remove the bagger top when it is closed; open the bagger top and then remove it.

decal1 10-6691

1 10-6691

1. Thrown object hazard—keep bystanders away .

2. Thrown object hazard, mower—do not operate without the

deector , discharge cover , or grass collection system in

place.

3. Cutting/dismemberment hazard of hand or foot—stay away

from moving parts.

decal133-8061

133-8061

3

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description

Qty .

Use

1

No parts required

–

Prepare the machine.

2

No parts required

–

Remove the guards (machines equipped

with MyRide only).

Left weight-mounting bracket

1

Right weight-mounting bracket 1

Hex-head ange bolt (3/8 x 1 inch)

4

Locknut (3/8 inch)

6

Bagger weight 6

W asher 2

3

Bolt (3/8 x 2-3/4 inches)

2

Install the weights.

4

No parts required

–

Install the guards (machines equipped

with MyRide only).

Lower bagger mount 1

Hex-head ange bolt (5/16 x 1 inch)

4

Hex-ange nut (5/16 inch)

4

Hex-washer-head thread forming

screws (1/4 x 3/4 inch)

4

Pivot frame assembly

1

Clevis pin

1

Hairpin 3

Support rod

2

5

Flat washer (1/2 inch)

2

Install the lower bagger mount and pivot

frame.

Hood rod 16

Hairpin 1

Install the hood rod.

Bagger top 17

Bagger screen 1

Assemble the bagger top.

Rubber latch 1

Plastic screw 2

Plain washer 2

Bagger top assembly 1

Hopper bracket 2

Carriage bolt (5/16 inch x 1 inch)

4

Hex-ange nuts (5/16 inch)

4

Bag assembly 2

8

Bagger tube 1

Install the bagger top assembly .

9

Cutof f Baf e

1

Install the baf es (54in decks only).

Blade (21-5/8 inches – 42in decks only)

210

Blade (18-3/4 inches – 54in decks only)

3

Install the blades.

1 1

Chute

1 Install the chute.

12

No parts required

–

Connect with the discharge tube.

4

Note: Determine the left and right sides of the

machine from the normal operating position.

Contact an Authorized Service Dealer for installation

assistance.

1

Preparing the Machine

No Parts Required

Procedure

1. Park the machine on a level surface.

2. Disengage the blade-control switch.

3. Move the motion-control levers outward to the

NEUTRAL position.

4. Engage the parking brake.

5. Shut of f the machine and remove the key .

6. W ait for all moving parts to stop.

7. Allow machine components to cool.

8. Remove the battery packs from the machine.

2

Removing the Guards

Machines Equipped with MyRide

®

Only

No Parts Required

Procedure

Note: Retain all removed parts for later installation.

1. Remove the bolts securing the guards on the

sides of the frame.

2. Remove the guards on both sides of the frame

(Figure 3 ).

g467888

Figure 3

5

3

Installing the W eights

Parts needed for this procedure:

1

Left weight-mounting bracket

1 Right weight-mounting bracket

4

Hex-head ange bolt (3/8 x 1 inch)

6

Locknut (3/8 inch)

6 Bagger weight

2 W asher

2

Bolt (3/8 x 2-3/4 inches)

Procedure

Note: Retain all removed parts for later installation.

CAUTION

The bagger changes the weight distribution of the machine. Operating the machine without the

front weights may cause an unstable condition, which could result in a loss of control.

Ensure the front weights are properly installed before operating the machine with the bagger

attachment.

6

1. On the left side of the machine, remove the parking brake cover by removing the 2 shoulder screws

(1/4 x 1/2 inch).

g466921

Figure 4

2. Remove the shoulder screw (1/4 inch) that secures the brake cable to the brake pedal.

g466922

Figure 5

1. Brake pedal

3. Shoulder screw (1/4 inch)

2. Brake cable

7

3. Loosen the nut on the brake cable and remove it from the bracket by pulling the cable forward and out

of the slot, as shown below .

g466923

Figure 6

1. Nut 2. Brake cable

4. Remove the pedal return spring from the brake pedal and brake pedal bracket.

g466928

Figure 7

1. Brake pedal bracket 3. Brake pedal

2. Pedal return spring

8

5. Remove the hex-head ange bolt (5/16 x 2 inches), pivot washer , wave washer , ange bushing, and

hex-ange nut (5/16 inch) that secure the brake pedal to the brake pedal bracket.

g466929

Figure 8

1. Hex-ange nut (5/16 inch)

5. W ave washer

2. Brake pedal bracket 6. Pivot washer

3. Flange bushing

7. Hex-head ange bolt (5/16 x 2 inches)

4. Brake pedal

6. Remove the button-head screw (5/16 x 3/4 inch) that secures the brake pedal bracket to the frame rail.

g466483

Figure 9

1. Brake pedal bracket 3. Frame rail

2. Button-head screw (5/16 x 3/4 inch)

9

7. Slide the left weight-mounting bracket between the brake pedal bracket and frame rail. Secure the

brackets with the 2 hex-head ange bolts (3/8 x 1 inch), 2 locknuts (3/8 inch), and previously removed

button-head screw (5/16 x 3/4 inch).

g466959

Figure 10

1. Locknut (3/8 inch) 4. Button-head screw (5/16 x 3/4 inch)

2. Brake pedal bracket

5. Left-weight mounting bracket

3. Hex-head ange bolt (3/8 x 1 inch)

8. Install the right weight-mounting brackets to the under side of the frame using 2 hex-head ange bolts

(3/8 x 1 inch), and 2 locknuts (3/8 inch).

g466486

Figure 1 1

10

9. Install the hex-head ange bolt (5/16 x 2 inches), pivot washer , wave washer , ange bushing, and

hex-ange nut (5/16 inch) that secure the brake pedal to the brake pedal bracket.

g466929

Figure 12

1. Hex-ange nut (5/16 inch)

5. W ave washer

2. Brake pedal bracket 6. Pivot washer

3. Flange bushing

7. Hex-head ange bolt (5/16 x 2 inches)

4. Brake pedal

10. Install the pedal return spring to the brake pedal and brake pedal bracket.

g466928

Figure 13

1. Brake pedal bracket 3. Brake pedal

2. Pedal return spring

1 1

1 1. Install the shoulder screw (1/4 inch) that secures the brake cable to the brake pedal.

g466922

Figure 14

1. Brake pedal

3. Shoulder screw (1/4 inch)

2. Brake cable

12. On the brake cable, set the cable length by pulling the cable hand tight while tightening the nuts.

13. Install the parking brake cover by installing the 2 shoulder screws (1/4 x 1/2 inch).

g466921

Figure 15

12

14. Install the suitcase weights (amount determined by deck size) to the weight-mounting brackets using 2

bolts (3/8 x 2-3/4 inches), 2 washers, and 2 locknuts (3/8 inch) as shown below .

•42 inch decks: install 6 weights.

•54 inch decks: install 5 weights.

g466487

Figure 16

1. Bolt (3/8 x 2-3/4 inches) 4. Suitcase weight

2. W eight-mounting bracket

5. Locknut (3/8 inch)

3. W asher

15. Once you have installed the weights and brackets, ensure that all the fasteners are tight. T ighten as

necessary .

Important: Whenever you remove the bagger attachment, remember to remove the front weights

to return the proper stability to the machine.

13

4

Installing the Guards

Machines Equipped with MyRide

Only

No Parts Required

Procedure

1. Insert the top of the guard under the deck; tilt the

guard so that it slides under the frame and t the

guard into the notches ( Figure 17 ).

g308505

g308526

Figure 17

1. Notch

2. Secure the guards to the frame using the bolts

removed in 2 Removing the Guards ( page 5 ) .

14

5

Installing the Lower Bagger Mount and Pivot Frame

Parts needed for this procedure:

1 Lower bagger mount

4

Hex-head ange bolt (5/16 x 1 inch)

4

Hex-ange nut (5/16 inch)

4

Hex-washer-head thread forming screws (1/4 x 3/4 inch)

1

Pivot frame assembly

1

Clevis pin

3 Hairpin

2

Support rod

2

Flat washer (1/2 inch)

Procedure

1. On each side of the machine, remove the 3 button-head screws (5/16 x 3/4 inch) that secure the rear

guard to the frame rail.

g466961

Figure 18

15

2. On the backside of the machine, install the lower bagger mount to the rear guard using the 4 hex-head

ange bolts (5/16 x 1 inch) and 4 hex-ange nuts (5/16 inch).

g466498

Figure 19

1. Rear guard

3. Hex-head ange bolt (5/16 x 1 inch)

2. Lower bagger mount

3. On the lower backside of the machine, install the bagger support to the frame rails using the 4

hex-washer-head thread forming screws (1/4 x 3/4 inch).

g466531

Figure 20

1. Hex-washer-head thread forming screws (1/4 x 3/4 inch)

3. Bagger support

2. Frame rail

16

4. On each side of the machine, install the 3 button-head screws (5/16 x 3/4 inch) that secure the rear

guard to the frame rail.

g466961

Figure 21

17

5. Insert the pivot frame assembly into the lower bag mount and secure it with the clevis and hairpin.

g466542

Figure 22

18

La page charge ...

Toro 42in Bagger, eTimecutter Riding Mower Manuel utilisateur

Ce manuel convient également à

Toro 42in Bagger, eTimecutter Riding Mower Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents