Toro E-Z Vac Complete Twin Bagger, TimeCutter HD Riding Mower Manuel utilisateur

Form No. 3465-1 16 Rev A

E-Z V ac™ Complete T win Bagger

79345 , 79346

Komplettes Heckfangsystem mit zwei Fangkörben

E-Z V ac™

79345 , 79346

Système de ramassage complet E-Z V ac™ HD à deux

bacs

79345 , 79346

Système de ramassage complet E-Z V ac™ HD à deux

bacs

79345 , 79346

www .T oro.com.

*3465-116*

Form No. 3464-976 Rev A

E-Z V ac

™

Complete T win Bagger

T imeCutter

®

HD and T itan

®

Riding Mower

Model No. 79345 —Serial No. 415204500 and Up

Model No. 79346 —Serial No. 415186600 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3464-976*

W ARNING

CALIFORNIA

Proposition 65 W arning

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for product safety and operation

training materials, accessory information, help nding

a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

g005673

Figure 1

1. Model and serial number location

Model No.

Serial No.

This manual uses 2 words to highlight information.

Important calls attention to special mechanical

information and Note emphasizes general information

worthy of special attention.

The safety-alert symbol ( Figure 2 ) appears both in

this manual and on the machine to identify important

safety messages that you must follow to avoid

accidents. This symbol will appear with the word

Danger ,W arning , or Caution .

•Danger indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury .

•W arning indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury .

•Caution indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury .

sa-black

Figure 2

1. Safety-alert symbol

Contents

Safety ....................................................................... 3

T owing Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Setup ........................................................................ 6

1 Preparing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Installing the W eight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Removing the Grass Deector and Belt

Cover .............................................................. 8

4 Installing the Baf e and Blower

Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5 Installing the Pulley Assembly , Belt Cover ,

and Shoulder Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

6 Installing the Attachment Mount . . . . . . . . . . . . . . . . . . . . . . 1 1

7 Installing the Latch Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

8 Assembling the Bagger T op . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

9 Assembling the Grass Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

10 Installing the Bagger T op . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1 1 Installing the Blower Assembly . . . . . . . . . . . . . . . . . . . . . 16

12 Installing the Blower Belt and Powered

Bagger Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

13 Installing the Discharge T ubes . . . . . . . . . . . . . . . . . . . . . 18

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Emptying the Grass Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Clearing Obstructions from the Bagger . . . . . . . . . . . . . 22

Removing the Bagger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Recommended Maintenance Schedule(s) . . . . . . . . . . . 24

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in the USA

Preparing for Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Cleaning the Hood Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Cleaning the Bagger and Bags . . . . . . . . . . . . . . . . . . . . . . . . . 25

Inspecting the Blower Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Replacing the Blower Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Inspecting the Bagger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Inspecting the Mower Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Storing the Bagger Attachment . . . . . . . . . . . . . . . . . . . . . . . . . 26

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Safety

W ARNING

When the bagger is in operation, the blower

is rotating and can cut off or injure hands and

ngers.

• Before adjusting, cleaning, repairing,

and inspecting the blower , and before

unclogging the chute, shut off the engine

and wait for all moving parts to stop.

Remove the key .

• Use a stick, not your hands, to remove an

obstruction from the blower and tube.

• Keep hands and feet away from moving

parts. Do not make adjustments with the

engine running.

W ARNING

Debris, such as leaves, grass, or brush can

catch re. A re in the engine area can cause

personal injury and property damage.

• Keep the engine and mufer area free of

debris accumulation.

• T ake care when opening the bagger cover

to keep debris from falling onto the engine

and mufer area.

• Allow the machine to cool before storing it.

•Become familiar with the safe operation of the

equipment, with the operator controls, and safety

signs.

•Use extra care with grass catchers or other

attachments. These can change the operating

characteristics and the stability of the machine.

•Follow the manufacturer's recommendations

for adding or removing wheel weights or

counterweights to improve stability .

•Do not use a grass catcher on steep slopes. A

heavy grass catcher could cause loss of control

or overturn the machine.

•Slow down and use extra care on hillsides. Be

sure to travel in the recommended direction on

hillsides. T urf conditions can af fect the stability of

the machine. Use extreme caution while operating

near drop-of fs.

•Keep all movement on slopes slow and gradual.

Do not make sudden changes in speed, direction,

or turning.

•The grass catcher can obstruct the view to the

rear . Use extra care when operating in reverse.

3

•Use care when loading or unloading the machine

into a trailer or truck.

•Never operate with the discharge deector raised,

removed or altered, unless using a grass catcher .

•Keep hands and feet away from moving parts. Do

not make adjustments with the engine running.

•Park the machine on level ground, disengage

the drives, chock the wheels, and shut of f the

engine before leaving the operator's position for

any reason including emptying the grass catcher

or unclogging the chute.

•If you remove the grass catcher , be sure to install

any discharge deector or guard that might have

been removed to install the grass catcher . Do not

operate the mower without either the entire grass

catcher or the grass deector in place.

•Shut of f the engine before removing the grass

catcher or unclogging the chute.

•Do not leave grass in the grass catcher for

extended periods of time.

•Grass catcher components are subject to wear ,

damage and deterioration, which could expose

you to moving parts or allow objects to be thrown.

Frequently check components and replace with

the manufacturer's recommended parts, when

necessary .

T owing Safety

•Do not attach towed equipment except at the hitch

point.

•Follow the attachment manufacturer's

recommendation for weight limits for towed

equipment and towing on slopes.

•Never allow children or others in or on towed

equipment.

•On slopes, the weight of the towed equipment may

cause loss of traction and loss of control. Reduce

towed weight and slow down.

•Stopping distance increases with the weight of the

towed load. T ravel slowly and allow extra distance

to stop.

•Make wide turns to keep the attachment clear of

the machine.

•Do not tow a load that weighs more than the

towing machine.

4

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal136-4164

136-4164

1. W arning—read the Operator ’ s Manual . 4. Cutting/dismemberment hazard, impeller—keep away from

moving parts; keep all guards and covers in place.

2. W arning—hearing protection must be worn.

5. Cutting/dismemberment hazard, impeller—disengage the

PT O, remove the key , and wait for all moving parts to stop.

3. Thrown object hazard—do not operate the blower without the

entire system installed and latched.

6. W arning; loss of traction—do not operate with only

counterbalance weights installed; do not operate with only

E-Z V ac installed; operate only with both E-Z V ac and

counterbalance weights installed.

decal109-6809

109-6809

1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s)

from the bagger . Do not remove the bagger top when it is closed; open the bagger top and then remove it.

decal133-8061

133-8061

5

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description

Qty .

Use

1

No parts required

–

Prepare the machine.

W eight tray 1

Left weight-tray mount

1

Right weight-tray mount 1

Suitcase weight—16 kg (35 lb)

1

Retaining rod 1

Bolt (3/8 x 1-1/4 inches)

2

Flange nut (3/8 inch)

4

Carriage bolt (3/8 x 1 inch)

2

Self-tapping bolt (5/16 x 3/4 inch)

2

Install the weight.

3

No parts required

–

Remove the grass deector and belt

cover .

Blower support 1

Hex washer-head screw (3/8 x 3/4 inch)

2

Baf e

1

Carriage bolt (5/16 x 3/4 inch)

44

Flange nut (5/16 inch)

4

Install the baf e and blower support.

Pulley assembly 15

Belt cover 1

Install the pulley assembly and belt

cover .

Stabilizer bracket

1

Carriage bolt (5/16 x 3/4 inch)

2

Locknut (5/16 inch)

4

Self-tapping screw (5/16 x 3/4 inch)

2

Bolt (5/16 x 1 inch)

2

Pivot frame

1

Hairpin cotter 2

Rod 2

6

W asher 2

Install the attachment mount.

Latch rod 17

Hairpin cotter 1

Install the latch rod.

Bagger top 1

Bagger screen 18

Hairpin cotter 2

Assemble the bagger top.

Bag frame

29

Grass bag

2

Assemble the grass bags.

10

Grass bag assembly

2 Install the bagger top.

1 1

Blower assembly 1 Install the blower assembly .

Powered bagger cover 112

Blower belt 1

Install the blower belt and powered

bagger cover .

6

Procedure Description

Qty .

Use

Upper tube 1

Screw (1/4 x 3/4 inches)

2

W asher (1/4 inch)

2

Locknut (1/4 inch)

213

Lower tube 1

Install the discharge tubes.

Determine the left and right sides of the machine from the normal operating position.

1

Preparing the Machine

No Parts Required

Procedure

Perform the following procedure to prepare the

machine for attaching the blower and nishing kit.

1. Park the machine on a level surface.

2. Disengage the blade-control switch, engage

the parking brake, and move the motion-control

levers outward to the NEUTRAL -LOCK position.

3. Shut of f the engine and remove the key .

4. Ensure that the machine is secure from

movement before you begin to work on it.

5. Repair all bent or damaged areas of machine

deck and replace any missing parts.

6. Clean the machine of any debris on the machine

deck or rear part of the machine to ease

installation.

2

Installing the W eight

Parts needed for this procedure:

1 W eight tray

1

Left weight-tray mount

1 Right weight-tray mount

1

Suitcase weight—16 kg (35 lb)

1 Retaining rod

2

Bolt (3/8 x 1-1/4 inches)

4

Flange nut (3/8 inch)

2

Carriage bolt (3/8 x 1 inch)

2

Self-tapping bolt (5/16 x 3/4 inch)

Procedure

CAUTION

The bagger changes the weight distribution of

the machine. Operating the machine without

the front weights may cause an unstable

condition, which could result in a loss of

control.

Ensure that the front weights are properly

installed before operating the machine with

the bagger attachment.

1. Remove the existing bolt and nut from the left

and right side of the platform where you will

install the weight-tray mounts.

2. Use the 2 self-tapping bolts (5/16 x 3/4 inch), 2

bolts (3/8 x 1-1/4 inches), and ange nuts (3/8

inch) to secure the left and right weight-tray

mounts to the machine ( Figure 3 ).

7

g196533

Figure 3

Cutaway view

1. W eight-tray mounts

3. Flange nut (3/8 inch)

2. Bolt (3/8 x 1-1/4 inches) 4. Self-tapping bolt (5/16 x

3/4 inch)

3. Use the 2 carriage bolts (3/8 x 1 inch) and ange

nuts to secure the weight tray to the mounts

(Figure 4 ).

g196549

Figure 4

1. Carriage bolt (3/8 x 1 inch)

3. W eight tray

2. W eight-tray mount

4. Flange nut (3/8 inch)

4. Insert the suitcase weight into the weight tray

with the groove side facing toward the front of

the machine ( Figure 5 ).

g196560

Figure 5

1. Retaining rod

3. Suitcase weight

2. W eight tray

5. Insert the retaining rod into the tray and rotate it

into the locked position ( Figure 5 ).

Important: Remove the suitcase weight whenever

you remove the bagger attachment.

3

Removing the Grass

Deector and Belt Cover

No Parts Required

Procedure

W ARNING

An uncovered discharge opening could allow

the machine to throw objects toward you or

bystanders and result in serious injury . Also,

contact with the blade could occur .

Never operate the lawn mower unless you

install a mulch plate, discharge deector , or

grass-collection system.

Inspect the grass deector for damage before each

use. Replace any damaged parts before use.

1. Disengage the spring from the notch in the

deector bracket and remove the cotter pin (CE

models only), slide the rod out of the welded

deck brackets, spring, and discharge deector

(Figure 6 ).

8

Note: Y our chute may look dif ferent than the

one pictured.

g190642

Figure 6

1. Rod

4. Spring

2. Cotter pin (CE models

only)

5. Deck brackets

3. Deector 6. Spring installed over the

rod

2. Remove the deector ( Figure 6 ).

3. Remove the 4 screws (1/4 x 1/2 inch) securing

the right belt cover , and remove the belt cover

(Figure 7 ).

Note: Retain the 4 screws (1/4 x 1/2 inch) for

installation in Procedure 5 Installing the Pulley

Assembly , Belt Cover , and Shoulder Bolt ( page

1 1 ) .

g200974

Figure 7

1. Screw (1/4 x 1/2 inch)

2. Belt cover

4

Installing the Bafe and

Blower Support

Parts needed for this procedure:

1 Blower support

2

Hex washer-head screw (3/8 x 3/4 inch)

1

Baf e

4

Carriage bolt (5/16 x 3/4 inch)

4

Flange nut (5/16 inch)

Procedure

1. Install the blower support to the mower deck

using 2 hex washer-head screws (3/8 x 3/4 inch)

as shown in Figure 8 .

g201299

Figure 8

1. Hex washer-head screw

(3/8 x 3/4 inch)

2. Blower support

9

2. Remove the existing bolt and nut from the

mower deck ( Figure 9 ).

Important: For 48-inch and 60-inch mower

decks, there is only one bolt and nut that you

can remove.

For 54-inch mower deck, remove the bolt and

nut as shown in Figure 9 .

g206498

Figure 9

1. Existing bolt 2. Existing nut

3. Install the left side of the baf e using a carriage

bolt (5/16 x 3/4 inch) and ange nut (5/16 inch)

as shown in Figure 10 .

4. Loosen the 2 carriage bolts (5/16 x 3/4 inch) in

the baf e slots, and slide the baf e until the hole

aligns with the hole in the mower deck ( Figure

10 ).

5. Install baf e as shown in Figure 10 .

Important: Ensure that you use the correct

hole for the bafe; refer to Figure 10 .

6. T ighten the 2 carriage bolts (5/16 x 3/4 inch) in

the baf e slots ( Figure 10 ).

g206496

Figure 10

54-inch mower deck shown

1. Inner baf e

6. Install this carriage bolt

(5/16 x 3/4 inch) and

ange nut (5/16 inch) after

sliding the baf e.

2. Hole for 48-inch and

60-inch mower deck

installation.

7. Slots in the baf e

3. Hole for 54-inch mower

deck installation.

8. Loosen these 2 carriage

bolts (5/16 x 3/4 inch) and

2 ange nut (5/16 inch).

4. Right blade 9. Install this carriage bolt

(5/16 x 3/4 inch) and

ange nut (5/16 inch) rst.

5. Outer baf e

10

5

Installing the Pulley

Assembly , Belt Cover ,

and Shoulder Bolt

Parts needed for this procedure:

1 Pulley assembly

1 Belt cover

Procedure

1. Remove the nut and washer from the right

mower deck pulley .

2. Install the pulley assembly to the right mower

deck pulley with the previously removed nut and

washer ( Figure 1 1 ).

Important: For 48-inch mower decks, use

the small blower pulley .

For 54-inch and 60-inch mower decks, use

the large blower pulley .

3. T orque the nut to 136 to 149 N∙m (100 to 1 10

ft-lb).

g201880

Figure 1 1

54-inch mower deck shown

1. Existing pulley nut

4. Existing deck (spindle)

pulley

2. Existing washer

5. Spindle

3. Blower pulley

4. Install the new belt cover over the pulley

assembly using the 4 previously removed

screws (1/4 x 1/2 inch) as shown in Figure 12 .

g201435

Figure 12

1. Belt cover

2. Screw (1/4 x 1/2 inch)

6

Installing the Attachment

Mount

Parts needed for this procedure:

1

Stabilizer bracket

2

Carriage bolt (5/16 x 3/4 inch)

4

Locknut (5/16 inch)

2

Self-tapping screw (5/16 x 3/4 inch)

2

Bolt (5/16 x 1 inch)

1

Pivot frame

2 Hairpin cotter

2 Rod

2 W asher

Procedure

1. Remove the existing 2 bolts, 2 nuts, and hitch

bracket from the bottom of the engine guard

(Figure 13 ).

1 1

g308798

Figure 13

1. Nut 3. Bolt

2. Existing hitch bracket

2. Install the stabilizer bracket to the engine guard

using 2 carriage bolts (5/16 x 3/4 inch) and 2

locknuts (5/16 inch) as shown in Figure 14 .

g308799

Figure 14

1. Locknut (5/16 inch) 2. Carriage bolt (5/16 x 3/4

inch)

3. Remove the existing 2 self-tapping screws from

the bottom of the machine frame ( Figure 16 ).

4. Loosely install the pivot frame to the machine

frame using 2 bolts (5/16 x 1 inch) and 2 locknuts

(5/16 inch) as shown in Figure 15 .

g302477

Figure 15

1. Locknut (5/16 inch) 2. Bolt (5/16 x 1 inch)

5. Position the pivot frame upward, and secure the

pivot frame to the bottom of the machine frame

using 2 self-tapping screws (5/16 x 3/4 inch) as

shown in Figure 16 .

g308797

Figure 16

1. Self-tapping screw (5/16 x

3/4 inch)

2. Pivot frame

6. T ighten the 2 bolts (5/16 x 1 inch) and 2 locknuts

(5/16 inch) as shown in Figure 15 .

7. Install the bent, ared end of a rod into the keyed

slot in the left side of the machine frame, and

move the rod rearward to seat it in the frame

(Figure 17 ).

Note: Repeat this step for the right side of the

machine.

12

g308335

Figure 17

Left side shown

8. Insert the bent ends of the rods into the

attachment mount as shown in Figure 17 and

secure the end of each rod with a washer and

hairpin cotter .

7

Installing the Latch Rod

Parts needed for this procedure:

1 Latch rod

1 Hairpin cotter

Procedure

Install the latch rod with a hairpin cotter ( Figure 18 ).

g201213

Figure 18

1. Hairpin cotter 2. Latch rod

13

8

Assembling the Bagger T op

Parts needed for this procedure:

1 Bagger top

1 Bagger screen

2 Hairpin cotter

Procedure

1. T urn the bagger top over .

2. Install the screen as shown in Figure 19 and

ensure that it slopes down toward the collection

bags.

Note: Make sure that the screens snap into

place and the tabs engage the bagger top.

g201881

Figure 19

1. Bagger top

4. Slot in bagger top

2. Screen

5. Hairpin cotter

3. Screen tab

14

9

Assembling the Grass Bags

Parts needed for this procedure:

2

Bag frame

2

Grass bag

Procedure

Snap the 2 bag frames to the 2 grass bags.

g453040

Figure 20

10

Installing the Bagger T op

Parts needed for this procedure:

2

Grass bag assembly

Procedure

1. Install the bagger top to the bagger frame.

Note: Y our bagger may look dif ferent than the

one shown.

2. Slide the brackets over the posts in the bagger

frame and install the circular cotter pin into the

hole in the right hand post ( Figure 21 ).

3. Rotate the bagger hood down to the operating

position.

Note: T o remove the circular cotter pin,

continue to rotate it in the same direction as

installed.

g016265

Figure 21

1. Bagger hood

4. Circular cotter pin

2. Bagger frame

5. Post

3. Bracket, bagger hood

15

4. Lift the bagger top and install the bags

assembled in 9 Assembling the Grass Bags

( page 15 ) by sliding the bag frame hooks onto

the retaining brackets ( Figure 22 ).

g300378

Figure 22

5. Lower the bagger top onto the bags ( Figure 23 ).

g033030

Figure 23

6. Secure the hood with the latch ( Figure 23 ).

1 1Installing the Blower

Assembly

Parts needed for this procedure:

1 Blower assembly

Procedure

W ARNING

An uncovered discharge opening allows the

lawn mower to throw objects toward you or

bystanders, resulting in serious injury . Also,

contact with the blade could occur .

• Never operate the lawn mower without a

cover plate, a mulch plate, or a grass chute

and catcher .

• Make sure that the grass deector is

installed when you remove the grass chute

and catcher .

Important: Install the side-discharge chute when

you remove the bagger and blower .

Important: Save all the hardware and the

side-discharge chute.

1. If necessary , install the belt onto the blower

pulley ( Figure 26 ).

2. Insert the blower pivot pin into the blower

support and rotate the blower assembly inward

toward the machine ( Figure 24 ).

Note: The blower assembly should

automatically latch as shown in Figure 25 .

16

g201514

Figure 24

1. Blower assembly 3. Blower support

2. Blower pivot pin

g201893

Figure 25

1. Blower latch

12

Installing the Blower Belt

and Powered Bagger Cover

Parts needed for this procedure:

1 Powered bagger cover

1 Blower belt

Procedure

1. Install the belt around the blower pulley ( Figure

26 and Figure 27 ); refer to 1 1 Installing the

Blower Assembly ( page 16 ) .

Use the following belt based on the mower

deck size:

48-inch Mower

Deck

54-inch Mower

Deck

60-inch Mower

Deck

T oro Part No.

127-0074

T oro Part No.

127-0075

T oro Part No.

127-0076

g201516

Figure 26

Blower Belt Routing

1. Idler/tension pulley

3. Blower belt

2. Blower pulley 4. Drive pulley

17

g201513

Figure 27

1. Blower pulley 5. Idler arm

2. Blower in position (housing

portion removed for

illustrative purposes)

6. Drive pulley

3. Spring 7. Idler/tension pulley

4. Idler-pulley post 8. Blower belt

2. Ensure that the belt remains aligned to the

blower pulley while you are installing the blower

assembly .

3. Pull the spring loaded idler pulley away from the

xed spring post, and route the belt around the

mower deck pulley ( Figure 27 ).

Note: Ensure that the belt is routed around the

blower pulley correctly .

4. Route the belt around the drive pulley as

illustrated in Figure 26 and Figure 27 .

5. Install the powered bagger cover over the belt

cover , and secure it by tightening the knob

(Figure 28 ).

g201515

Figure 28

1. Knob 3. Belt cover

2. Powered bagger cover

13

Installing the Discharge

T ubes

Parts needed for this procedure:

1 Upper tube

2

Screw (1/4 x 3/4 inches)

2

W asher (1/4 inch)

2

Locknut (1/4 inch)

1 Lower tube

Procedure

Important: Make sure that the mower deck is in

the lowest height-of-cut position before installing

the discharge tubes.

Note: Remember to install the grass deector when

you remove the bagger from the mower .

1. Disengage the PT O and engage the parking

brake.

2. Shut of f the engine and remove the key .

3. Lower the mower deck to the lowest height-of-cut

position.

4. Remove the bags for viewing the tube under

the hood.

5. Lower and latch the hood.

6. Use both latches to attach the lower tube to the

blower assembly ( Figure 29 ).

Note: Ensure that the notch in the lower tube is

at the bottom when installed ( Figure 31 ).

18

La page charge ...

Toro E-Z Vac Complete Twin Bagger, TimeCutter HD Riding Mower Manuel utilisateur

Ce manuel convient également à

Toro E-Z Vac Complete Twin Bagger, TimeCutter HD Riding Mower Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents