Toro 54in Bagger, eTimecutter Riding Mower Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur

Ce manuel convient également à

Form No. 3466-378 Rev A
42in or 54in Bagger
79841 , 79851
Heckfangsystem (107 cm oder 137
cm)
79841 , 79851
Système de ramassage de 107 cm ou
137 cm
79841 , 79851
Grasvanger van 107 cm en van 137
cm
79841 , 79851
*3466-378*
Form No. 3466-364 Rev B
42in or 54in Bagger
eT imecutter Riding Mower
Model No. 79841 —Serial No. 400000000 and Up
Model No. 79851 —Serial No. 400000000 and Up
Operator's Manual
Introduction
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
Whenever you need service, genuine parts, or
additional information, contact an Authorized Service
Dealer or Customer Service and have the model
and serial numbers of your product ready . Figure 1
identies the location of the model and serial numbers
on the product. W rite the numbers in the space
provided.
g466960
Figure 1
1. Model and serial number location
Model No.
Serial No.
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
The safety-alert symbol ( Figure 2 ) appears both in
this manual and on the machine to identify important
safety messages that you must follow to avoid
accidents. This symbol will appear with the word
Danger ,W arning , or Caution .
Danger indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury .
W arning indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury .
Caution indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury .
sa-black
Figure 2
1. Safety-alert symbol
Original Instructions (EN)
Printed in the USA
All Rights Reserved
*3466-364*
W ARNING
CALIFORNIA
Proposition 65 W arning
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer , birth defects,
or other reproductive harm.
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1 Preparing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Removing the Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3 Installing the W eights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Installing the Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Installing the Lower Bagger Mount and
Pivot Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Installing the Hood Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7 Assembling the Bagger T op . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 Installing the Bagger T op Assembly . . . . . . . . . . . . . . . . 20
9 Installing the Baf e (54in Decks
Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10 Installing the Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1 1 Installing the Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
12 Connecting with the Discharge
T ube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Emptying the Grass Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Clearing Obstructions from the Bagger . . . . . . . . . . . . . 27
Removing the Bagger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Recommended Maintenance Schedule(s) . . . . . . . . . . . 30
Inspecting the Bagger Attachment . . . . . . . . . . . . . . . . . . . . 30
Inspecting the Mower Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Cleaning the Bagger Attachment . . . . . . . . . . . . . . . . . . . . . . 30
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Storing the Bagger Attachment . . . . . . . . . . . . . . . . . . . . . . . . . 31
Safety
Become familiar with the safe operation of the
equipment, with the operator controls, and safety
signs.
Use extra care with grass catchers or other
attachments. These can change the operating
characteristics and the stability of the machine.
Follow the manufacturer's recommendations
for adding or removing wheel weights or
counterweights to improve stability .
Do not use a grass catcher on steep slopes. A
heavy grass catcher could cause loss of control
or overturn the machine.
Slow down and use extra care on hillsides. Be
sure to travel in the recommended direction on
hillsides. T urf conditions can af fect the stability of
the machine. Use extreme caution while operating
near drop-of fs.
Keep all movement on slopes slow and gradual.
Do not make sudden changes in speed, direction,
or turning.
The grass catcher can obstruct the view to the
rear . Use extra care when operating in reverse.
Use care when loading or unloading the machine
into a trailer or truck.
Never operate with the discharge deector raised,
removed or altered, unless using a grass catcher .
Keep hands and feet away from moving parts. Do
not make adjustments with the machine running.
Park the machine on level ground, disengage the
drives, and shut of f the machine before leaving
the operator's position for any reason including
emptying the grass catcher or unclogging the
chute.
If you remove the grass catcher , be sure to install
any discharge deector or guard that might have
been removed to install the grass catcher . Do not
operate the mower without either the entire grass
catcher or the grass deector in place.
Do not leave grass in the grass catcher for
extended periods of time.
Grass catcher components are subject to wear ,
damage and deterioration, which could expose
you to moving parts or allow objects to be thrown.
Frequently check components and replace with
the manufacturer's recommended parts, when
necessary .
Do not use the machine as a towing vehicle.
2
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger . Replace any decal that is damaged or missing.
decal109-6809
109-6809
1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s)
from the bagger . Do not remove the bagger top when it is closed; open the bagger top and then remove it.
decal1 10-6691
1 10-6691
1. Thrown object hazard—keep bystanders away .
2. Thrown object hazard, mower—do not operate without the
deector , discharge cover , or grass collection system in
place.
3. Cutting/dismemberment hazard of hand or foot—stay away
from moving parts.
decal133-8061
133-8061
3
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure Description
Qty .
Use
1
No parts required
Prepare the machine.
2
No parts required
Remove the guards (machines equipped
with MyRide only).
Left weight-mounting bracket
1
Right weight-mounting bracket 1
Hex-head ange bolt (3/8 x 1 inch)
4
Locknut (3/8 inch)
6
Bagger weight 6
W asher 2
3
Bolt (3/8 x 2-3/4 inches)
2
Install the weights.
4
No parts required
Install the guards (machines equipped
with MyRide only).
Lower bagger mount 1
Hex-head ange bolt (5/16 x 1 inch)
4
Hex-ange nut (5/16 inch)
4
Hex-washer-head thread forming
screws (1/4 x 3/4 inch)
4
Pivot frame assembly
1
Clevis pin
1
Hairpin 3
Support rod
2
5
Flat washer (1/2 inch)
2
Install the lower bagger mount and pivot
frame.
Hood rod 16
Hairpin 1
Install the hood rod.
Bagger top 17
Bagger screen 1
Assemble the bagger top.
Rubber latch 1
Plastic screw 2
Plain washer 2
Bagger top assembly 1
Hopper bracket 2
Carriage bolt (5/16 inch x 1 inch)
4
Hex-ange nuts (5/16 inch)
4
Bag assembly 2
8
Bagger tube 1
Install the bagger top assembly .
9
Cutof f Baf e
1
Install the baf es (54in decks only).
Blade (21-5/8 inches – 42in decks only)
210
Blade (18-3/4 inches – 54in decks only)
3
Install the blades.
1 1
Chute
1 Install the chute.
12
No parts required
Connect with the discharge tube.
4
Note: Determine the left and right sides of the
machine from the normal operating position.
Contact an Authorized Service Dealer for installation
assistance.
1
Preparing the Machine
No Parts Required
Procedure
1. Park the machine on a level surface.
2. Disengage the blade-control switch.
3. Move the motion-control levers outward to the
NEUTRAL position.
4. Engage the parking brake.
5. Shut of f the machine and remove the key .
6. W ait for all moving parts to stop.
7. Allow machine components to cool.
8. Remove the battery packs from the machine.
2
Removing the Guards
Machines Equipped with MyRide
®
Only
No Parts Required
Procedure
Note: Retain all removed parts for later installation.
1. Remove the bolts securing the guards on the
sides of the frame.
2. Remove the guards on both sides of the frame
(Figure 3 ).
g467888
Figure 3
5
3
Installing the W eights
Parts needed for this procedure:
1
Left weight-mounting bracket
1 Right weight-mounting bracket
4
Hex-head ange bolt (3/8 x 1 inch)
6
Locknut (3/8 inch)
6 Bagger weight
2 W asher
2
Bolt (3/8 x 2-3/4 inches)
Procedure
Note: Retain all removed parts for later installation.
CAUTION
The bagger changes the weight distribution of the machine. Operating the machine without the
front weights may cause an unstable condition, which could result in a loss of control.
Ensure the front weights are properly installed before operating the machine with the bagger
attachment.
6
1. On the left side of the machine, remove the parking brake cover by removing the 2 shoulder screws
(1/4 x 1/2 inch).
g466921
Figure 4
2. Remove the shoulder screw (1/4 inch) that secures the brake cable to the brake pedal.
g466922
Figure 5
1. Brake pedal
3. Shoulder screw (1/4 inch)
2. Brake cable
7
3. Loosen the nut on the brake cable and remove it from the bracket by pulling the cable forward and out
of the slot, as shown below .
g466923
Figure 6
1. Nut 2. Brake cable
4. Remove the pedal return spring from the brake pedal and brake pedal bracket.
g466928
Figure 7
1. Brake pedal bracket 3. Brake pedal
2. Pedal return spring
8
5. Remove the hex-head ange bolt (5/16 x 2 inches), pivot washer , wave washer , ange bushing, and
hex-ange nut (5/16 inch) that secure the brake pedal to the brake pedal bracket.
g466929
Figure 8
1. Hex-ange nut (5/16 inch)
5. W ave washer
2. Brake pedal bracket 6. Pivot washer
3. Flange bushing
7. Hex-head ange bolt (5/16 x 2 inches)
4. Brake pedal
6. Remove the button-head screw (5/16 x 3/4 inch) that secures the brake pedal bracket to the frame rail.
g466483
Figure 9
1. Brake pedal bracket 3. Frame rail
2. Button-head screw (5/16 x 3/4 inch)
9
7. Slide the left weight-mounting bracket between the brake pedal bracket and frame rail. Secure the
brackets with the 2 hex-head ange bolts (3/8 x 1 inch), 2 locknuts (3/8 inch), and previously removed
button-head screw (5/16 x 3/4 inch).
g466959
Figure 10
1. Locknut (3/8 inch) 4. Button-head screw (5/16 x 3/4 inch)
2. Brake pedal bracket
5. Left-weight mounting bracket
3. Hex-head ange bolt (3/8 x 1 inch)
8. Install the right weight-mounting brackets to the under side of the frame using 2 hex-head ange bolts
(3/8 x 1 inch), and 2 locknuts (3/8 inch).
g466486
Figure 1 1
10
9. Install the hex-head ange bolt (5/16 x 2 inches), pivot washer , wave washer , ange bushing, and
hex-ange nut (5/16 inch) that secure the brake pedal to the brake pedal bracket.
g466929
Figure 12
1. Hex-ange nut (5/16 inch)
5. W ave washer
2. Brake pedal bracket 6. Pivot washer
3. Flange bushing
7. Hex-head ange bolt (5/16 x 2 inches)
4. Brake pedal
10. Install the pedal return spring to the brake pedal and brake pedal bracket.
g466928
Figure 13
1. Brake pedal bracket 3. Brake pedal
2. Pedal return spring
1 1
1 1. Install the shoulder screw (1/4 inch) that secures the brake cable to the brake pedal.
g466922
Figure 14
1. Brake pedal
3. Shoulder screw (1/4 inch)
2. Brake cable
12. On the brake cable, set the cable length by pulling the cable hand tight while tightening the nuts.
13. Install the parking brake cover by installing the 2 shoulder screws (1/4 x 1/2 inch).
g466921
Figure 15
12
14. Install the suitcase weights (amount determined by deck size) to the weight-mounting brackets using 2
bolts (3/8 x 2-3/4 inches), 2 washers, and 2 locknuts (3/8 inch) as shown below .
42 inch decks: install 6 weights.
54 inch decks: install 5 weights.
g466487
Figure 16
1. Bolt (3/8 x 2-3/4 inches) 4. Suitcase weight
2. W eight-mounting bracket
5. Locknut (3/8 inch)
3. W asher
15. Once you have installed the weights and brackets, ensure that all the fasteners are tight. T ighten as
necessary .
Important: Whenever you remove the bagger attachment, remember to remove the front weights
to return the proper stability to the machine.
13
4
Installing the Guards
Machines Equipped with MyRide
Only
No Parts Required
Procedure
1. Insert the top of the guard under the deck; tilt the
guard so that it slides under the frame and t the
guard into the notches ( Figure 17 ).
g308505
g308526
Figure 17
1. Notch
2. Secure the guards to the frame using the bolts
removed in 2 Removing the Guards ( page 5 ) .
14
5
Installing the Lower Bagger Mount and Pivot Frame
Parts needed for this procedure:
1 Lower bagger mount
4
Hex-head ange bolt (5/16 x 1 inch)
4
Hex-ange nut (5/16 inch)
4
Hex-washer-head thread forming screws (1/4 x 3/4 inch)
1
Pivot frame assembly
1
Clevis pin
3 Hairpin
2
Support rod
2
Flat washer (1/2 inch)
Procedure
1. On each side of the machine, remove the 3 button-head screws (5/16 x 3/4 inch) that secure the rear
guard to the frame rail.
g466961
Figure 18
15
2. On the backside of the machine, install the lower bagger mount to the rear guard using the 4 hex-head
ange bolts (5/16 x 1 inch) and 4 hex-ange nuts (5/16 inch).
g466498
Figure 19
1. Rear guard
3. Hex-head ange bolt (5/16 x 1 inch)
2. Lower bagger mount
3. On the lower backside of the machine, install the bagger support to the frame rails using the 4
hex-washer-head thread forming screws (1/4 x 3/4 inch).
g466531
Figure 20
1. Hex-washer-head thread forming screws (1/4 x 3/4 inch)
3. Bagger support
2. Frame rail
16
4. On each side of the machine, install the 3 button-head screws (5/16 x 3/4 inch) that secure the rear
guard to the frame rail.
g466961
Figure 21
17
5. Insert the pivot frame assembly into the lower bag mount and secure it with the clevis and hairpin.
g466542
Figure 22
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140

Toro 54in Bagger, eTimecutter Riding Mower Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Ce manuel convient également à