Pentair 618031 Mode d'emploi

INSTALLATION GUIDE

COLOR SYNC™ CONTROLLER

FOR PENTAIR COLOR LED POOL LIGHTS

sAm

Party

Romance

Carribbean

American

Sunset

Royal

Blue

Green

Magenta

White

Red

HOLD RECALL

Color Sync Controller Installation Guide

For Installation of Electrical Controls at Equipment Pad (ON/OFF

Switches, Timers and Automation Load Center)

Install all electrical controls at equipment pad, such as on/off switches,

timers, and control systems, etc. to allow the operation (startup, shut-

down, or servicing) of any pump or ﬁlter so the user does not place

any portion of his/her body over or near the pump strainer lid, ﬁlter

lid or valve closures. This installation should allow the user enough

space to stand clear of the ﬁlter and pump during system start-up,

shut down or servicing of the system ﬁlter.

Color Sync Controller Installation Guide

2 3

IMPORTANT!

Attention Installer: This manual contains important information

about the installation, operation and safe use of this product.

This information should be given to the owner and/or operator

of this equipment. When installing and using this electrical

equipment, basic safety precautions should always be followed,

including the following:

IMPORTANT SAFETY INSTRUCTIONS PERTAINING

TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS. READ AND FOLLOW ALL INSTRUCTIONS.

DANGER! RISK OF ELECTRIC SHOCK, WHICH CAN

RESULT IN SERIOUS INJURY OR DEATH. Before

attempting installation or service, ensure that all power to

the circuit supplying power to the system is disconnected/

turned off at the circuit breaker.

Grounding (earth bonding) is required. The Color Sync

Controller should be installed by a qualiﬁed professional

and grounded.

Read Safety Precautions and Important Instructions.

Before attempting any electrical wiring, be sure to read

and follow Safety Instructions. Wiring should only be

performed by a qualiﬁed professional.

Before installing this product, read and follow all warning

notices and instructions which are included. Failure to follow

safety warnings and instructions can result in severe injury,

death, or property damage. Call (800) 831-7133 for additional

free copies of these instructions.

WARNINGS AND IMPORTANT SAFETY PRECAUTIONS

Color Sync Controller Installation Guide

General Installation Information

1. Allworkmustbeperformedbyalicensedelectricianorqualiedpoolprofessional,and

mustconformtoallnational,state,andlocalcodes.

2. Install to provide drainage of compartment for electrical components.

3. This equipment is not provided with integral Ground Fault Circuit Interruptors (GFCI)

protection.Whenthisequipmentisusedtopowerorswitchanunderwaterluminaire,

suitableGFCIprotectionshallbeprovidedintheeld.Luminairecircuitconductorsshall

notoccupytheconduit,boxesorenclosureswithothercircuitsunlesstheothercircuits

are also GFCI protected.

4. The electrical supply for this product must include a suitably rated switch or circuit

breaker to open all ungrounded supply conductors to comply with in accordance with the

currentNationalElectricalCode(NEC),NFPA70ortheCanadianElectricalCode(CEC),

CSA C22.1. All applicable local installation codes and ordinances must also be adhered

to. The disconnecting means must be readily accessible to the tub occupant but installed

atleast10ft.(3.05m)fromtheinsidewallofthepool.

2 3

WARNINGS AND IMPORTANT SAFETY PRECAUTIONS

Color Sync Controller Installation Guide

4 5

RFExposureRequirements: The antenna(s) used for this device must be installed to provide a

separationdistanceofatleast7.0inches(20cm)fromallpersonsandmustnotbeco-located

or operating in conjunction with any other antenna or transmitter.

L’antenne(s)utilisépourcetappareildoitêtreinstallépourfournirunedistancedeséparation

d’aumoins(20cm)àpartirdetouteslespersonnesetnedoitpasêtreco-localisésou

fonctionnerenconjonctionavecuneautreantenneouunautreémetteur.

FCCStandard-47CFRPart15,SubpartC(Section15.247).Thisversionislimitedtochapter1

tochapter11byspeciedrmwarecontrolledintheU.S.A.

Instructiontouser-Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfor

aClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedto

provide reasonable protection against harmful interference in a residential installation. This

equipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandused

inaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.If

thisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbe

determinedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrectthe

interferencebyoneormoreofthefollowingmeasures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Note:InordertomaintaincompliancewithFCCregulations,shieldedcablesmustbeusedwith

thisequipment.Operationwithnon-approvedequipmentorunshieldedcablesislikelytoresult

ininterferencetoradioandTVreception.Theuseriscautionedthatchangesandmodications

madetotheequipmentwithouttheapprovalofthemanufacturercouldvoidtheuser’sauthorityto

operate this equipment.

Canada-IndustryCanada(IC)RegulatoryNotice:-ThisdevicecomplieswithRSS210of

Industry Canada. (1999).

UnderIndustryCanadaregulations,thisradiotransmittermayonlyoperateusinganantennaof

atypeandmaximum(orlesser)gainapprovedforthetransmitterbyIndustryCanada.Toreduce

potentialradiointerferencetootherusers,theantennatypeanditsgainshouldbesochosenthat

the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful

communication.ThisdevicecomplieswithIndustryCanadalicence-exemptRSSstandard(s).

Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseinterference,

and(2)thisdevicemustacceptanyinterference,includinginterferencethatmaycauseundesired

operation of the device.

Conformémentàlaréglementationd’IndustrieCanada,leprésentémetteurradiopeutfonctionner

avecuneantenned’untypeetd’ungainmaximal(ouinférieur)approuvépourl’émetteurpar

IndustrieCanada.Danslebutderéduirelesrisquesdebrouillageradioélectriqueàl’intention

desautresutilisateurs,ilfautchoisirletyped’antenneetsongaindesortequelapuissance

isotroperayonnéeéquivalente(p.i.r.e.)nedépassepasl’intensiténécessaireàl’établissement

d’unecommunicationsatisfaisante.LeprésentappareilestconformeauxCNRd’Industrie

Canadaapplicablesauxappareilsradioexemptsdelicence.L’exploitationestautoriséeaux

deuxconditionssuivantes:(1)l’appareilnedoitpasproduiredebrouillage,et(2)l’utilisateurde

l’appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesilebrouillageestsusceptible

d’encompromettrelefonctionnement.

WARNINGS AND IMPORTANT SAFETY PRECAUTIONS

Color Sync Controller Installation Guide

4 5

WARNINGS AND IMPORTANT SAFETY PRECAUTIONS

Be sure the pool electrical system conforms with all requirements of the

National Electrical Code (NEC), and all local codes and ordinances. A licensed

or certiﬁed electrician must install the electrical system to meet or exceed those

requirements before the Color Sync™ Controller is installed. The electrician

should also consult the local building department regarding local codes. Some of

the NEC requirements are listed below:

• The Controller must be installed by a qualiﬁed electrician, according

to the National Electrical Code (including article 680) or Canadian

Electrical Code (including section 68) and, local code requirements.

For Canadian installations, supply circuit must be protected by a

ground fault circuit interrupter.

• The Controller must be provided with a fail-proof ground as required

by NEC, Article 680 and any applicable local codes For Canadian

installations, the supply circuit must be protected by a ground fault

circuit interrupter.

• Do not install the Controller within 5 feet (3 meters for Canadian

installations) of any body of water. USE COPPER CONDUCTORS

O N LY.

• The Controller should be mounted at least 1 foot above the water and

ground level.

• Do not exceed the maximum ratings of individual components, wiring

devices, and current carrying capacity of conductors.

• For grounding and bonding the Controller and the installation, refer

to section 680 of the National Electrical Code or section 68 of the

Canadian Electrical Code.

• The lighting circuit must have a Ground Fault Circuit Interrupter

(GFCI), and an appropriately rated circuit breaker.

• The light ﬁxture and all metal items within ﬁve (5) feet of the pool

must be properly electrically bonded.

• The Controller must be properly electrically bonded and grounded.

• Do not submerge the Controller.

• Do not connect two or more Controllers together.

Color Sync Controller Installation Guide

6 7

Contents

Warnings and Important Safety Precautions .........

Overview / Features ..............................................

Color Sync Controller Controls and Buttons ..........

Color Sync Controller Power (Wattage)

and Maximum Number of Connected Lights..........

Outlet Box Location / Specications .....................

Installing the Outlet box ........................................

Wiring Lights to the Color Sync Controller.............

Wiring Lights to the Color Sync Controller

using a 300 WattTransformer...............................

Mounting the Controller into the Outlet Box .........

Color Sync Controller Mounting Kit

Replacement .......................................................

Troubleshooting the Color Sync Controller...........

Color Sync Controller Dimensions........................

2-5

7

8

9

10

11

12

13

14

16

18

CUSTOMER SERVICE / TECHNICAL SUPPORT

Customer Service and Technical Support, USA

(8 AM - 5:00 PM — Eastern/Pacic Times)

Phone: (800) 831-7133

Fax: (800) 284-4151

www.pentair.com

Sanford, North Carolina (8 AM - 5.00 PM

ET) Phone: (919) 566-8000

Fax: (919) 566-8920

Moorpark, California (8 AM - 5.30 PM PT)

Phone: (805) 553-5000 (Ext. 5591)

Fax: (805) 553-5515

Download the free Pentair Home App:

Apple® (iOS® 11 or later). Scan the bar code or go to the Apple Store to

download the Pentair Home app.

Android® (v6.6 or later) smart devices. Scan the bar code or go to the

Google Store to download the Pentair Home app.

P/N 618034 REV A. 2/2021

Color Sync Controller Installation Guide

6 7

Overview

The Color Sync™ Controller gives you complete control of Pentair pool, spa

and landscape lights. It’s easy to select a lighting feature, just dial in any one

of the pre-programmed color light shows or ﬁxed colors. Using the Hold and

Recall feature you can also create endless unique lighting effects. The Color

Sync™ Controller can control individual or multiple Pentair color/white LED

lights, which are connected via a junction box to the controller so that all lights

can be switched on and off together.

Features

• Operating Voltage 120 VAC 60 Hz

• Power Rating 240 W continuous usage

• Wire Size: 12 AWG maximum

• UL/CSA listing

• UL/CSA type gang box

• Bluetooth® wireless technology paring

• WiFi connection/communication

• StorageTemperature:14°Fto185°F[-10°Cto85ׄ°C]

• AmbientOperatingTemperature:14°Fto149°F[-10°Cto65°C]

Environment: Outdoor rated (Must use provided gasket and wet location

rated outlet junction box end bracket)

For online Color Sync manuals, visit www.pentair.com

• Color Sync Quick Start Guide (P/N 618032)

• Color Sync Pentair Home App User's Guide (P/N 618033)

• Color Sync Installation Guide (P/N 618034). This manual

Color Sync Controller Installation Guide

8 9

Color Sync Controller

sAm

Party

Romance

Carribbean

American

Sunset

Royal

Blue

Green

Magenta

White

Red

HOLD RECALL

Hold LED

Fixed Color

Selections

Dial: Push/Hold for

ON/OFF - Rotate Dial

to select Color Shows,

then push and select

Hold to save for

color/show.

Push and select

Recall to recall

color/show

Recall LED

Color Light

Shows

WiFi/BT LED

(Link Status)

Color Sync™ Controller Controls and Buttons

Pentair Color Sync™ Controller controls, buttons and LEDs:

Color LED Light

Type

Wattage Per

Light

Maximum

Recommended

Number of Lights

(240W Continuous)

MicroBrite® Color 14 W 17

IntelliBrite® 5G

Color 26 W 9

GloBrite® Color 15 W 16

Note: The Color Sync controller is not designed to use

incandescent lights. Be sure the total electrical load of the

controller does NOT exceed 240 Watts. See Table above

and page 11 for more information.

Color Sync™ Controller Power (Wattage) and Maximum

Number of Connected Lights

Color Sync Controller Installation Guide

8 9

Outlet Box Speciﬁcations

(purchased separately)

The Color Sync Controller requires a

standard outlet box which is purchased

separately. The outlet box must meet the

following speciﬁcations:

• Outlet box type: 22.5 cubic

inches (minimum) - Suitable

for wet locations with

UL/CSA approval listings.

Check the inside of outlet box

for speciﬁcation label.

• A minimum of one 3/4” conduit

inlet. Outlet Box

Height

4.50”

Width 2.75” Depth 1.60”

Outlet Box Location

Before installing the Color Sync Controller, read the following guidelines

carefully:

1. Before permanent installation, test the 2.4 GHz WiFi signal strength at

the location where the controller will be mounted (refer to "Testing WiFi

Signal Strength" in the Color Sync Pentair Home App User’s Guide).

The controller operates on 2.4 GHz. Note: Be sure the home network

router supports 2.4 GHz. Dual Band routers are supported.

2. If possible, minimize the number and volume of obstacles that may block

the wireless signal to the enclosure.

3. Beforechoosingthenallocationforthecontroller,considerthelengthof

all AC power wires that will need to be connected to the unit.

4. Mounttheunitonaatverticalsurfacewithunobstructedaccesstothe

front of the unit. The unit can be mounted inside your house, outside or

inside of a pool equipment shed or other enclosures.

5. All electrical equipment, except for UL Listed spa-side remote switches,

must be installed no fewer than 5 ft. (1.5 m). For Canada, 3 m (9.75 ft.)

from the pool and/or spa. Comply with all national state, and local code

6. CAUTION: Install the controller in a location to allow enough space at the

equipmentpadtostandclearofthelterandpumpduringsystem

start-up.

COLOR SYNC™ CONTROLLER AND OUTLET BOX INSTALLATION

Color Sync Controller Installation Guide

10 11

Installing the Outlet box

To install the outlet box:

1. Position the controller and outlet box to meet National Electrical Code

requirements, and to prevent hazard to personnel.

2. Run conduit from the pool/spa light niche to the junction box.

Note: The outlet box must be located a minimum distance of ﬁve (5)

feet measured horizontally from the inside wall of the pool and not

less than one (1) foot above the maximum pool water level

measured to the top of the outlet box.

3. Remove the lower conduit plug from the outlet box.

4. Mount the outlet box onto the conduit.

Outlet Box

Lower

conduit

plug

Color Sync Controller Installation Guide

10 11

To wire Pentair 120 VAC or 12 VAC Lights to the Color Sync Controller:

1. Route the Pentair color LED Light cord (for 120VAC lights only), or the

supply wires for the Pentair transformer, along with the three supply wires

(White, Green and Black) from the GFCI, up through the conduit opening

into the outlet box. See page 12 for wiring diagram.

2. Strip the ends of all the conductors a minimum of 1/4”. Note: Use under-

water lights with water resistant cord only.

3. Using the ground screw in the outlet box, secure the Green ground wire

from the light, and the GFCI to the back of the outlet box.

4. Place the gasket onto Color Sync back of the controller before connecting

the wires.

5. 12 VAC LIGHT: Connect the the LOAD wire from the controller to the step

down transformer. Note: Connect the light to the secondary 12 VAC

output of the step-down transformer, then connect the Controller to

the 120 VAC primary input of the step down transformer.

120 VAC LIGHT: Connect the LOAD wire from the controller junction box

to HOT line wire of the light. IMPORTANT! 120 VAC POOL/SPA LIGHTS

MUST HAVE A GFCI CONNECTION.

6. Connect the White (Neutral) wire from the Color Sync Controller to the

White wire from the light cord, and the White (Neutral) wire from the GFCI,

using an appropriately sized wire nut.

TURN power OFF at circuit breaker - Always disconnect power to

the pool light at the circuit breaker before servicing the light. Failure

to do so could result in death or serious injury to installer, service

person, pool users, or others due to electrical shock.

300 Watts Maximum Load. The total allowable light wattage is

300 Watts maximum. Loading above 300 W will cause permanent

damage to the Color Sync Controller and may render it

permanently inoperable.

IMPORTANT! RECOMMENDED 80% LOADING AT 240 WATTS IS

THE PREFERRED MAXIMUM LOAD PERMISSIBLE FOR

CONTINUOUS OPERATION.

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION

WIRING LIGHTS TO THE COLOR SYNC™ CONTROLLER

The Color Sync Controller is a 120 VAC device, DO NOT connect 12

VAC Pentair Color LED lights directly to the Color Sync Controller, use an

appropriate step down transformer between the controller and lights.

Color Sync Controller Installation Guide

12 13

L

N

12 VAC

Step Down

Transformer

12 VAC Pentair

Color LED Lights

Red (Hot Load line -

Transformer / Light)

Black (Hot Line Incoming Power)

White/Blue (Neutral)

LOAD

NEUTRAL (WHT)

LINE (BLK)

Outlet box screw hole (X6)

BLACK

RED

WHITE

Hot Load Line (Transformer/Light)

Neutral (White) Line (to Light or

Hot (Black) Line (incoming power)

transformer and incoming neutral)

LOAD

NEUTRAL (WHT)

LINE (BLK)

Hot Load Line (Transformer/Light)

Neutral (White) Line (to Light or

Hot (Black) Line (incoming power)

transformer and incoming neutral)

LOAD

NEUTRAL (WHT)

LINE (BLK)

WIRING LIGHTS TO THE COLOR SYNC™ CONTROLLER

Color Sync Controller

(RearView)

Color Sync Controller Installation Guide

12 13

wire nut

120 VAC Input

12O VAC Wall Outlet

GREEN

WHITE

BLACK

GREEN

WHITE

BLACK

WHITE

RED

300 Watt Transformer

AC Power cord

Color LED Lights

BLACK

300 W

12 VAC

Safety

Transformer

12 VAC Output

12 VAC

Color Sync Controller

The controller mounts into a standard outlet box (22.5 cubic inches minimum).

See page 9 for outlet box speciﬁcations. Note: After wiring to the controller is

complete, check all wiring connections before mounting the controller into the

outlet box.

To install the controller into the outlet box:

1. Neatly arrange the wires in the back of the outlet box.

2. Apply the provided grease to the screw threads (to avoid damaging

gasket).

3. Align the controller with the screw holes of the outlet box.

4. Secure the Controller to the outlet box with the two (2) front retaining

screws.

sAm

Party

Romance

Carribbean

American

Sunset

Royal

Blue

Green

Magenta

White

Red

HOLD RECALL

Mounting the Controller into the Outlet Box

INSTALLING THE CONTROLLER INTO THE OUTLET BOX

Color Sync Controller Installation Guide

14 15

To remove and install a new gasket:

1. Remove the two front screws from the front plate.

2. Carefully remove the controller, face plate and gasket from the outlet

box.

3. Using a small ﬂat-blade screw drive, disconnect the three (3) power

wires by loosen the three (3) screws on the connector terminals located

on the lower rear side of the controller. See page 12 for wiring diagram.

4. Separate the gasket from the face plate and discard the gasket.

TURN power OFF at circuit breaker - Always disconnect power to

the pool light at the circuit breaker before servicing the light. Failure

to do so could result in death or serious injury to installer, service

person, pool users, or others due to electrical shock.

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION

Controller and Gasket

Front screw (x2) Gasket

3 wire connector

screw terminal

COLOR SYNC CONTROLLER MOUNTING KIT REPLACEMENT

MOUNTING KIT CONTENTS (P/N 602159Z):

• Gasket, Screws (x2), Grease Packet

Color Sync Controller Installation Guide

14 15

TURN power OFF at circuit breaker - Always disconnect power to

the pool light at the circuit breaker before servicing the light. Failure

to do so could result in death or serious injury to installer, service

person, pool users, or others due to electrical shock.

5. Install the new gasket: Place the gasket behind the face plate ﬂush

against the back of the face plate as shown below.

6. Reconnect the three (3) wires to the connector screw terminal as shown

on page 12.

Controller Gasket Rear View

3 wire connector

screw terminal

Gasket

Face plate

7. Using the provided grease, lubricate the two screw threads.

8. Secure the controller in the outlet box with the two front screws.

Screw (x2) Gasket

Lubricate

screw threads

COLOR SYNC CONTROLLER MOUNTING KIT REPLACEMENT

Color Sync Controller Installation Guide

16 17

PROBLEM/

FAULT

SYMPTOM CHECK SOLUTION

Lightsdonot

turn on.

Noneofthepool/

spa lights are on

after turning the

Controller on.

Be sure the wiring and

installation setup is

correct,andlinevolt-

age input (Black and

white) to the

Controller,and

switched output (Red)

wireisat120VAC.

If the Controller has an

LEDindicatorONlightON

nexttoacolororacolor

sequence,andvoltages

readcorrectlyat120VAC,

and Controller did not go

intooverloadcondition,then

replace the

Controller.

Lightsturn

ON but do not

remain

synchronized.

One or some of

the lights display

a different color

and do not stay in

sync with the rest

of the lights.

Check the Controller

and lights by

selecting one of the

xedcolormodes.

Resetthelight(s):Holdthe

Controller button until it

resets. Try again and see if

lights remain in sync. If not

replace the Controller.

Lightswillnotturn

on and all Color

SyncLEDsareall

ashing.

The Color Sync

controller has detected

an electrical load in

excessofthe

maximumallowable

wattageormaximum

allowable unit

temperature. Turn off

power at the circuit

breaker and inspect all

electrical systems

including Color Sync

transformer (if present).

Refertomaximum

wattage of light

controller (page 11) to

ensure power does not

exceed300W.

Reduce lights load (watt-

age)onthecontrollerand/

or replace damaged

electrical systems. Turn

OFF power to the controller

offatthecircuitbreaker,

thenturnbackontore-set

the controller to resume

operation.

Troubleshooting the Color Sync™ Controller

Use the following troubleshooting chart to resolve some of the common faults

or problems.

Color Sync Controller Installation Guide

16 17

Troubleshooting the Color Sync™ Controller (Continued)

PROBLEM/

FAULT

SYMPTOM CHECK SOLUTION

AllLightsare

not turning on.

One or some of

the lights are not

turning on.

Disconnectthelights,

then reconnect them

one by one. Be sure

the problem is not with

the lights.

If problem is with the lights;

replace faulty light(s). If

problempersists,make

sure the correct transformer

(XFRMR)output12/13/14

VACisselectedfortheload

andcablelengths:Referto

the Transformer

Installation and Guide. If

problem still persists then

replace Controller.

Color Sync Controller Installation Guide

18 19

2.95 in

(75 cm)

1.21 in

30.80 cm 0.118 in

0.3 cm

4.72 in

(120 cm)

3.268 in

(83 cm)

Color Sync™ Controller Dimensions

Color Sync Controller Installation Guide

18 19

Notes

1620 HAWKINS AVE., SANFORD, NC 27330 • (919) 566-8000

10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000

WWW.PENTAIR.COM

All indicated Pentair trademarks and logos are property of Pentair Inc. or its global affiliates in the

U.S.A. and/or other countries. Third party registered and unregistered trademarks and logos are the

property of their respective owners. The Bluetooth® word mark and logos are registered trademarks

owned bythe Bluetooth SIG, Inc. and any use of such marks by Pentair Management Company is under

license. Other trademarks and trade names are those of their respective owners. iPhone®, iPad®, iPod

touch®, Apple® App Store® and iTunes® are registered trademark of Apple Inc. in the United States

and/or other countries. Google Play® and Android® are registered trademarks of Google LLC in the

United States and/or other countries.

P/N 618034 REV A. 2/2021

*619751*

Pentair 618031 Mode d'emploi

Ce manuel convient également à

Pentair 618031 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents