Honeywell 2D Presentation Mode d'emploi

2D Presentation
Honeywell
Marque
Honeywell
Modèle
2D Presentation
Catégorie
Lecteurs de codes à barres
Taper
Mode d'emploi
2D Presentation
Barcode Scanner
2D Presentation Barcode Scanner Quick Guide (Rev1)
P/N: 8013-0074000
SPECIFICATIONS
DIMENSIONS SCANNING RANGE BEEPER INDICATION GENERAL SETTINGS
Light source visible red LED
Sensor 640 x 480
Scan rate 120 frames/sec
Resolution 4mil/ 0.1mm
PCS 20%
Width of Field 135mm (13Mil Code39)
Depth of Field 13 Mil UPC/EAN: 10 - 208mm
(Typical)
10 Mil DataMatrix: 5 - 107mm
15 Mil QR Code: 5 - 181mm
Dimension W85 x L85 x H155 mm
Weight 250g
Connector USB Type A, D - sub 9
Cable 200cm/78.7in (Interchangeable)
Interface USB HID, RS232
Indicator LED, Buzzer
Voltage 5VDC±5%
Working Current < 500mA
Standby Current < 500mA
Operating Temp. -30 to 70°C (-22°F to 158°F)
Storage Temp. -40 to 80°C (-40°
F to 176°F)
Ambient Light 100,000 lux (Sunlight)
Drop Durability 1.5M
Symbologies QR Code, DataMatrix, PDF417, Han Xin
MaxiCode and all major 1D barcodes
Quick Guide
FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise for digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de las classe B prescrites dans le
Réglement sur le brouillage radioélectrique édicté par les ministère des Communica-
tions du Canada.
CE MARKING AND EUROPEAN UNION COMPLIANCE
Testing for compliance to CE requirements was performed by an independent
laboratory. The unit under test was found compliant with all the applicable Directives,
2004/108/EC and 2006/95/EC.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and
importers to take-back electronic products at the end of their useful life.
ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2002/95/EC.
NON-MODIFICATION STATEMENT
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment
RoHS
1. Take any metals into contact with the terminals in connectors.
2. Use the scanner where any inflammable gases.
If following condition occur, immediately power off the host computer,
disconnect the interface cable, and contact your nearest dealer.
1. Smoke, abnormal odors or noises come from the scanner.
2. Drop the scanner so as to affect the operation or damage its housing.
Do Not
Do not do behavior below.
1. Put the scanner in places excessively high temperatures such as expose
under direct sunlight.
2. Use the scanner in extremely humid area or drastic temperature
changes.
3. Place the scanner in oily smoke or steam environment such as cooking
range.
4. Be covered or wrapped up the scanner in bad-ventilated area such as
under cloth or blanket.
5. Insert or drop foreign materials or water into scanning window or vents.
6. Using the scanner while hand is wet or damp.
7. Use the scanner with anti-slip gloves containing plasticizer and
chemicals or organic solvents such as benzene, thinner, insecticide etc
to clean the housing. Otherwise, it could not result fire and electrical
shock but housing may be broken and injured.
8. Scratch or modify the scanner and bend, twist, pull or heat its interface
cable.
9. Put heavy objects on interface cable.
Do not stare the light source from the scanning window or do not point the
scanning window at other people’s eyes or eyesight may be damaged
by direct exposure under the light.
Do not put the scanner on an unstable or inclined plane.
The scanner may drop, creating injuries.
Once the interface cable is damaged such as exposed or broken copper
wires, stop using immediately and contact your dealer. Otherwise, it could
result fire or electrical shock.
WARNING AND CAUTION
CHECK VERSION
DEFAULT
Single Short Beep Good read
Three beeps Successful setup
Four beeps Power up
1. The scanner works like an USB keyboard. Make sure
your host device supports USB keyboard before use.
2. Plug the scanner to the USB port of your host device.
The scanner will emit four beeps at power-up.
3. The OS will automatically intall USB driver for the
scanner if it is connected to your host device for the
first time. Wait until the installation finishes.
4. Open Notepad or any application that can accept
keyboard input. Try scanning some random barcodes
and the barcode data will be displayed.
LED INDICATION
GETTING STARTED
Green Good read
Blue Normal mode
Red Special mode (disable Code39)
(Top View)
13 Mil EAN/UPC: 10 - 208mm
15 Mil QR Code: 5 - 181mm
10Mil Data Matrix: 5 - 107mm
45°
Unit: MM
•
R
eo
•
In
c
• Co
r
e
• Co
A
NA
T
his
d
appa
Comm
Le
p
r
é
rr
limi
te
R
égle
RR
ti
o
n
s
CE
M
T
e
s
tin
labo
r
20
0
4
W
AS
T
he
W
i
m
po
RO
HS
48
rotatable
85
(Unit = mm, tolerance = ±0.2mm)
119.8
154.8
85
BEEPER
ENABLE ALL 1D CODES
ENABLE ALL 2D CODES DISABLE ALL 2D CODES
DISABLE ALL 1D CODES
KEYBOARD LAYOUT
GERMAN FRENCH
ENGLISH (UK)
SPANISH ITALIAN
DANISH HUNGARIAN ROMANIAN
(STANDARD)
BELGIAN
DUTCH
CZECH
POLISH (214) GREEK
NORWEGIAN
SLOVAK SWEDISH FINNISH
JAPANESE THAILAND CR+LF
CR+CR CR+LF+CR+LF
RUSSIAN UKRAINE
TABBRAZILIAN (ABNT2)
PORTUGUESE
ENGLISH
(
USA
)
NONE
SYMBOLOGIES
GOOD READ BEEP ON
POWER UP BEEP ON
SETUP BEEP ON
GOOD READ BEEP OFF
POWER UP BEEP OFF
SETUP BEEP OFF
TERMINATOR
CAPITAL LOCK
CR
NONE
ALL UPPER CASE
ALL LOWER CASE INVERT CASE
  • Page 1 1
  • Page 2 2

Honeywell 2D Presentation Mode d'emploi

2D Presentation
Honeywell
Marque
Honeywell
Modèle
2D Presentation
Catégorie
Lecteurs de codes à barres
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents