Pentax N-0751M-OD Guide d'installation

Marque: Pentax

Modèle: N-0751M-OD

Catégorie: Chauffe-eau

Taper: Guide d'installation

Ce manuel convient également à

N-0751M

Potential dangers from accidents during installation and use are divided into the following three

categories. Closely observe these warnings, they are critical to your safety.

Prohibited

Disconnect

Power

Ground

Be sure to do

Requests to Installers

• In order to use the water heater safely, read this installation manual carefully, and follow the

installation instructions.

• Failures and damage caused by erroneous work or work not as instructed in this manual are not

covered by the warranty.

• Check that the installation was done properly in accordance with this Installation Manual upon

completion.

•

After completing installation, please either place this Installation Manual in a plastic pouch and

attach it to the side of the water heater (or the inside of the pipe cover or recess box if applicable),

or hand it to the customer to retain for future reference. Also, be sure to fill in all of the required

items on the warranty and to hand the warranty to the customer along with the Owner's Guide.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

Installation must conform with local codes, or in the absence of local

codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54- latest edi-

tion and/or CSA B149.1, Natural Gas and Propane Installation Code

(NSCNGPIC).

Noritz America reserves the right to discontinue, or change at any time,

the designs and/or specifications of its products without notice.

NORITZ AMERICA

CORPORATION

Installation Manual

DANGER indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

DANGER

CAUTION

WARNING

CAUTION

WS-06-9012

Rev. 01/07

Low NOx

Approved by

SCAQMD

CERTIFIED

N-0751M (Indoor/Outdoor Installation)

N-0751M-OD (Outdoor Installation)

TANKLESS GAS WATER HEATER

Canada

07.1.12, 3:04 PMPage 1

Included Accessories

The following accessories are included with the unit.

Check for any missing items before starting installation.

Q’tyShapePart

Tapping Screw

(N-0751M only)

each

Part Shape Q’ty

Remote Controller

(See p. 21)

Remote Controller

Cord (3m(10'))

Optional Accessories

The accessories listed below are not

included with the units, but may be necessary

for installation.

Outdoor Vent Cap

(VC4(-1))

Quick Connect Cord

Q’tyShapePartPart Shape Q’ty

Remote Controller

Cord (8m(26'))

Isolator Exp

(includes pressure

relief valve)

Pipe Cover

[Outdoor installation only]

Remote Controller

Outdoor

Junction Box

Owner's Guide, Warranty,

Installation Manual

(this document)

Cross Recessed

Head Screw

(N-0751M-OD only)

Part Shape Q’ty

[ N-0751M only ]

Part Shape Q’ty

[ N-0751M-OD only ]

Recess Box

(RB-4)

07.2.5, 11:21 AMPage 2

Quick Connect Multi System Installation

• The Quick Connect Multi System allows the installation of two units together utilizing only the Quick

Connect Cord.

Typical Plumbing

The Quick Connect Cord is 2m (6'). long. Install the units 50 - 450mm (2-18") apart from each

other to ensure the cord will be able to reach between the units. (See Typical Plumbing diagram).

(If the distance between the two units is too great, not only will the cord not be able to reach,

but the water temperature may also become unstable because of the difference in pipe length

between the two units).

* When connecting two units, use only

a single remote controller.

Note: Connect the remote

controller to only one

of the units.

System Diagram

• Insulate the hot water piping to prevent heat loss. Insulate and apply heating materials to the cold

water supply piping to prevent heat loss and freezing of pipes when exposed to excessively cold

temperatures.

Quick Connect

Cord

Remote Controller Cord

Gas Supply Piping

Cold Water Supply

Hot Water

Remote Controller

Terminal Block

Cord

Connector

Cord

Connector

Union

Make this distance as short as possible.

* The hot water temperature will

become unstable as the pipe

length increases.

Distance at center

400 - 800mm (16-32")

Quick Connect

cord

Union

Gas Valve

Union

Shutoff

Valve

Shutoff Valve

Hot Water

Cold Water

Shutoff

Valve

Distance on sides

50 - 450mm (2-18")

Leave enough clearance around the plumbing to

apply insulation. It will be necessary to add

bends to the piping to ensure that this clearance

is available.

Pressure

Relief

Valve

Size the piping to allow for the maximum

flow rates of the units.

07.1.5, 4:34 PMPage 3

N-0751M

199,900 BTU

12,000 BTU

202

4.0

0.65

0 - 2,000 Ft.

(

0 - 610 m

)

199,900

168,000

2.0

0 - 2,000 ft.

(

0 - 610 m

)

2,000 - 4,500 ft

(

610 - 1,370 m

)

4.4" 4.4"

2.0

192,800

162,800

2,000 - 4,500 Ft.

(

610 - 1,370 m

)

2.55"

10.5"

765

Natural

Gaz Naturel

Before Installation

Checkup

• Check the fixing brackets and vent pipe yearly for damage or wear. Replace if necessary.

DANGER

Do Not Use Equipment for Purposes Other Than Those Specified

• Do not use for other than increasing the temperature of the water supply, as unexpected accidents

may occur as a result.

Check Water Supply Quality

• If the water supply is hard, acidic or otherwise impure, treat the water with approved methods in

order to ensure full warranty coverage.

WARNING

CAUTION

Check the Gas

• Check that the rating plate indicates the

correct type of gas.

• Check that the gas supply line is sized for

199,900 Btuh for this unit.

Check the Power

• The power supply required is 120V AC, at 60Hz.

Using the incorrect voltage may result in fire or electric shock.

Use Extreme Caution if Using With a Solar Pre-Heater

• Using this unit with a solar pre-heater can lead to unpredictable output temperatures and

possibly scalding. If absolutely necessary, use mixing valves to ensure output temperatures do

not get to scalding levels. Do not use a solar pre-heater with the quick-connect multi-system.

[For indoor installation only]

07.1.5, 4:34 PMPage 4

Choosing Installation Site

* Locate the appliance in an area where leakage from the unit or connections will not result in damage

to the area adjacent to the appliance or to the lower floors of the structure. When such locations

cannot be avoided, it is recommended that a suitable drain pan, adequately drained, be installed

under the appliance. The pan must not restrict combustion air flow.

• Install the exhaust vent so that there are no obstacles around the termination and so that

exhaust can't accumulate. Do not enclose the termination with corrugated metal or other

materials.

• Avoid places where fires are common, such as those where gasoline,

benzene and adhesives are handled, or places in which corrosive gases

(ammonia, chlorine, sulfur, ethylene compounds, acids) are present.

Using the incorrect voltage may result in fire or cracking.

• Avoid installation in places where dust or debris will accumulate.

Dust may block the air-supply opening, causing the performance of the

device fan to drop and incomplete combustion to occur as a result.

• Avoid installation in places where special chemical agents

(e.g., hair spray or spray detergent) are used.

Ignition failures and malfunction may occur as a result.

• Carbon Monoxide Poisoning Hazard. Do not install this water heater in a

mobile home, recreation vehicle or on a boat.

Prohibited

DANGER

WARNING

Indoor

• Do not enclose the termination with corrugated

metal or other materials.

This will cause carbon monoxide

poisoning and a potential fire

hazard.

[For indoor installation only]

[For outdoor installation only]

[Indoor installation]

Prohibited

[Outdoor installation]

07.1.5, 4:34 PMPage 5

• Install in a location where the exhaust gas flow will not be affected by fans or range hoods.

• Take care that noise and exhaust gas will not affect neighbors.

• Before installing, make sure that the vent termination (or the vent

cap in an outdoor installation) will have the proper clearances

according to the National Fuel Gas Code (ANSI Z223.1).

State of California: The water heater must be braced, anchored or strapped to avoid moving during an

earthquake. Contact local utilities for code requirements in your area or call: 1-800-456-9805 and request

instructions.

Be sure to do

Prohibited

CAUTION

• Consult with the customer concerning the location of installation.

• Do not install the water heater where the exhaust will blow on outer walls or material not resistant

to heat. Also consider the surrounding trees and animals.

The heat and moisture from the water heater may cause discoloration of walls and resinous

materials, or corrosion of aluminum materials.

• Install the water heater in a location where it is free from obstacles and stagnant air.

• Do not install the water heater near staircases or emergency exits.

•

Do not locate the vent termination directed towards a window or any

other structure which has glass or wired glass facing the termination.

•

Avoid installation where the unit will be exposed to excessive winds.

[For outdoor installation only]

[For indoor installation only]

• Avoid installation above gas ranges or stoves.

• Avoid installation between the kitchen fan and stove.

If oily fumes or a large amount of steam are present in the

installation location, take measures to prevent the fumes and

steam from entering in the equipment.

[For N-0751M only]

• Make sure that the location allows installation of the exhaust

vent as specified.

• For outdoor installation, use the outdoor vent cap.

If it is necessary to vent above the roof line in an outdoor

installation, also use the base of the vent cap for rain protection.

07.1.5, 7:32 PMPage 6

6. Installation Clearances

Before installing, check for the following:

Install in accordance with relevant building and mechanical codes, as well as any local, state or

national regulations, or in the absence of local and state codes, to the National Fuel Gas Code ANSI

Z223.1/NFPA 54 – latest edition. In Canada, see NSCNGPIC for detailed requirements.

Item

Required Clearances

From Heater

• Maintain the following clearance from

both combustible and non-combustible

materials.

Check Illustration

300mm (12") Indoor

900mm (36") Outdoor

600mm (24") Outdoor

100mm (4") Indoor

50mm (2") Indoor

600mm (24") Outdoor

• If possible, leave 200mm (8") or more on

either side of the unit to facilitate inspection.

• If possible, leave 600mm (24") or more in

front of the unit to facilitate maintenance

and service if necessary.

Securing of space for

repair/inspection

600mm

(24") or

200mm

(8") or

Min: 75mm (3")

• If the unit will be installed in the vicinity of a

permanent kitchen range or stove that has

the possibility of generating steam that

contains fats or oils, use a dividing plate or

other measure to ensure that the unit is not

exposed to air containing such impurities.

* The dividing plate should be of noncombust-

ible material of a width greater than the

water heater.

Exhaust hood

Range

Dividing plate

Water

heater

Cooking Equipment

WARNING

[ For N-0751M ]

200mm

(8") or

Min: 75mm (3")

07.1.5, 4:34 PMPage 7

Item Check

• When installing the unit on a balcony, etc., secure an

evacuation route of 600mm (24") or more in width.

• Provide clearance of 600mm (24") or more in front of the

unit to facilitate inspection and repair. Do install the unit

such as the wall of the second floor where the unit is out

of reach.

•

When installing the unit in a common side corridor, provide

a clearance of 1175mm (47") or more in front of the unit.

• Set the bottom edge of the exhaust port about 2100mm

(84") from the corridor floor.

Handrail

common side

corridor

balcony, etc.

Handrail

about

2100mm (84")

• Maintain the following clearance from both combustible

and non-combustible materials.

*( ) indicates the distance when installing a heat insulat-

ing board (incombustible material other than metal, with

thickness of 2.5mm (0.1") or more) or "section of build-

ing effectively finished with incombustible material."

Note, however, that combustion failure may occur to the

unit as exhaust gas reflects from the wall. Provide clear-

ance of 600mm (24") or more in the front of the unit to

facilitate inspection and repair.

600mm (24")

(300mm (12"))

or more

10mm

(

0.4")

or more

combustible

900mm

(36") or more

150mm

(6") or more

150mm

(6") or more

Surrounding the area of installation

600mm (24")

or more

1175mm (47")

or more

Required Clearances From Heater

combustible

[ For N-0751M -OD]

07.1.5, 4:34 PMPage 8

Vent Terminal

Clearance

Above grade, veranda, porch, deck,

or balcony

Window or door that may be opened

Permanently closed window

Vertical clearance to ventilated soffit

located above the terminal within a

horizontal distance of 0.6m

(

from

the center of the terminal

Unventilated soffit

Outside corner

Inside corner

Each side of center line extended

above meter/regulator assembly

0.9m (3') within a height 4.5m (15')

above meter/regulator assembly

0.9m (3') within a height 4.5m (15')

above meter/regulator assembly

Service regulator vent outlet

0.9m (3')

Nonmechanical air supply inlet or

combustion air inlet to any other

appliance

1.2m (4') below or to the side of

opening, or 0.3m (1') above

opening [900mm (36")]

1.2m (4') below or to the side of

opening, or 0.3m (1') above

opening [900mm (36")]

Mechanical air supply inlet

0.9m (3') above if within

3m (10') [1.8m (6')]

0.9m (3') above if within

3m (10') [1.8m (6')]

Above paved sidewalk or paved

driveway located on public property

Under veranda, porch, deck, or

balcony

[2.1m *** (7' ***)]

[ ]= indicates clearances required in Canada

* Maintain clearances in accordance with local installation codes and the requirements of the gas supplier

*** A vent shall not terminate directly above a sidewalk or paved driveway that is located between two

single family dwellings and serves both dwellings.

**** Permitted only if veranda,porch,deck,or balcony is fully open on a minimum of two sides beneath the floor.

*[300mm (12") - Canada Only****] *[300mm (12") - Canada Only****]

300mm (12") [300mm (12")]300mm (12") [300mm (12")]

300mm (12") [900mm (36")]

0.9m (3')

[2.1m *** (7' ***)]

Indoor Installation

(See p.10)

Outdoor Installation

(See p.10, 11)

Air Supply Inlet

Area Where Terminal

is Not Permitted

Clearance Requirements from Vent Terminations to Building Openings

* All clearance requirements are in accordance with ANSI Z21.10.3 and the National Fuel Gas Code,

ANSI Z223.1 and in Canada, in accordance with NSCNGPIC.

07.2.6, 1:29 PMPage 9

Vent Clearances When Heater is In-

stalled Indoors

• 1.2m (4') below, 1.2m (4') horizontally from,

or 0.3m (1') above any door, operable win-

dow, or gravity air inlet into any building.

0.9m (3') above any forced air inlet within

3m (10').

Maintain the following clearances to any

opening in any building:

Illustration

(Noritz vent cap)

• 0.3m (1') below, 0.3m (1') horizontally from,

or 0.3m (1') above any door, operable

window, or gravity air inlet into any building.

0.9m (3') above any forced air inlet within

3m (10').

Vent Clearances When Heater is In-

stalled Outdoors With a Vent Cap

* All clearance requirements are in accordance with ANSI Z21.10.3 and the National Fuel Gas Code,

ANSI Z223.1 and in Canada, in accordance with NSCNGPIC.

For Installations in Canada, clearances are as follows: To windows, doors, & gravity air inlets: 900mm (36").

To forced air inlets: 1.8m (6'). These clearance requirements hold true for all of the above situations: Indoor,

Outdoor w/vent cap.

0.9m (3')

0.3m (1')

1.2m (4')

0.3m (1')

0.9m (3')

0.3m (1')

Clearance Requirements from Vent Terminations to Building Openings

[ For N-0751M]

07.1.5, 4:34 PMPage 10

Maintain the following clearances to any

opening in any building:

Illustration

For Installations in Canada, clearances are as follows: To windows, doors, & gravity air inlets: 900mm (36").

To forced air inlets: 1.8m (6').

0.9m (3')

0.3m (1')

0.3m

(1')

Outdoor Clearances to Opening

into Any Building

• 0.3m (1') below, 0.3m (1') horizontally from,

or 0.3m (1') above any door, operable

window, or gravity air inlet into any building.

0.9m (3') above any forced air inlet within

3m (10').

Vent Clearances When Heater is

Installed in a Recess Box

(recess box installation with cover removed)

0.3m (1')

0.9m (3')

0.3m

(1')

0.3m

(1')

[ For N-0751M- OD]

• 0.3m (1') below, 0.3m (1') horizontally from,

or 0.3m (1') above any door, operable

window, or gravity air inlet into any building.

0.9m (3') above any forced air inlet within

3m (10').

07.1.5, 4:34 PMPage 11

Illustration

7. Installation

Check

4. Drill holes for the remaining four screws.

5. Hang the unit again by the first screw, and then

insert and tighten the remaining four screws.

6. Take waterproofing measures so that water does

not enter the building from screws mounting the

device.

• Make sure the unit is installed securely so that it will

not fall or move due to vibrations or earthquakes.

Securing to the wall

Mounting Bracket

(upper)

Tapping Screw

Location of Screw Hole

1. Drill a single screw hole, making sure to hit a stud.

2. Insert and tighten the screw and hang the unit by

the upper wall mounting bracket.

3. Determine the positions for the remaining four screws

(two for the top bracket and two for the bottom), and

remove the unit.

• The weight of the device will be applied to the wall. If the strength of the wall is not suffi-

cient, reinforcement must be done to prevent the transfer of vibration.

• Do not drop or apply unnecessary force to the device when installing. Internal parts may

be damaged and may become highly dangerous.

• Install the unit on a vertical wall and ensure that it is level.

Locating Screw Holes

Mounting

Structure

• When installing with bare hands, take caution to

not inflict injury.

• Be careful not to hit electrical wiring, gas, or water

piping while drilling holes.

Item

CAUTION

Be sure to do

• If this water heater is being installed at an elevation of

610m (2,000') or higher, disconnect the connector la-

beled "High Elevation Disconnect" as illustrated on the

right. This connector is located inside the unit.

Installations at Elevations

Above 610m (2,000').

HIGH ELEVATION

DISCONNECT

•Disconnect power to the water heater before discon-

necting this connector. Failure to perform this step will

result in a "73" code displayed on the remote controller

and a cease in operation. If this occurs, disconnect,

then reconnect power to the water heater to reset the

system.

07.1.5, 4:34 PMPage 12

• The first vertical run from the top of the heater

should be no longer than 0.9m (3').

• Make sure vent pipe is gas tight and will not

leak. Use silicon sealant wherever necessary.

• Do not common vent or connect more than

one appliance to this venting system.

•

The total vent length including horizontal & verti-

cal vent runs should be no less than 0.9m (3').

• Do not place any dangerous objects at the end

of the exhaust vent and check that vent pipe is

not blocked in any way.

• Steam (smoke) or water drops may come out

from the end of the exhaust pipe. Select the

location for the end of the vent so that steam is

not visible, and the vent is not wet with drip-

ping water.

• If snow is expected to accumulate, take care

the end of the pipe is not covered with snow or

hit by falling lumps of snow.

• Consult the vent pipe manufacturer's install-

ation instructions for chimney connections.

Appliance Adapters

• Use the following adapters to connect the

unit to the venting system.

Vent Piping

•Use only UL listed category III vent materials.

• Follow the vent pipe manufacturer's installation

instructions.

• Make the vertical section of the exhaust vent

as short as possible.

• Maintain the same vent pipe diameter from the

heater flue to the vent termination.

Pipe diameter 100mm (4")

No. of Elbows Max. Straight Vent Length

34.6m (15')

28.2m (27')

1 11.7m (39')

Clearances

These clearances are subject to change.

Refer to the UL listing for the proper clearances.

Manufacturer and

Product

Protech FasNSeal FSAA4

HeatFab SafTVent 9401RYPK

Z-Flex Z-Vent 2SVWA04

Flex-L Star-34 SRASPSA4

Part No.

WARNING

Be sure to do

CARBON MONOXIDE POISONING

Follow all vent system requirements in accordance with relevant local or state regulation,

or, in the absence of local or state code, in the U.S. to the National Fuel Gas Code ANSI

Z233.1/NFPA 54 – latest edition, and in Canada, in accordance with NSCNGPI.

[ For N-0751M]

Manufacturer and Enclosed Unenclosed

Product Hor. Vert. Hor. Vert.

Noritz N-Vent

Protech FasNSeal

Protech FasNSeal W2

HeatFab SafTVent

Z-Flex Z-Vent

Flex-L-StaR-34

100mm

(4")

100mm

(4")

100mm

(4")

100mm

(4")

100mm

(4")

75mm

(3")

75mm

(3")

75mm

(3")

75mm

(3")

75mm

(3")

75mm

(3")

50mm

(2")

50mm

(2")

25mm

(1")

25mm

(1")

25mm

(1")

25mm

(1")

150mm

(6")

150mm

(6")

150mm

(6")

200mm

(8")

200mm

(8")

250mm (10") (sides)

375mm (15") (top)

150mm (6") (bottom)

200mm (8") (sides)

300mm (12") (top)

100mm (4") (bottom)

Vent Pipe Installation

(Indoor Installation Only)

07.1.5, 4:34 PMPage 13

Vertical Vent Termination

Firestop

Firestop/

Support

Roof

Flashing

Roof

Jack

Storm

Collar

Rain

Cap

Hanger

Strap

Elbow

Condensation

Drain (Install

According to

Local Codes)

Appliance

Adapter*

* Adapter not required when

using Noritz N-Vent.

**0.3m (1') Min. -

0.9m (3') Max.

** 0.3m (1') minimum recommended,

but not required. Avoid installing

elbow directly on flue.

• Terminate at least 1.8m (6') from the combus-

tion air intake of any appliance, and 0.9m (3')

from any other building opening, gas utility

meter, service regulator etc.

• Enclose exterior vent systems below the roof

line to limit condensation and protect against

mechanical failure.

• When the vent penetrates a floor or ceiling and

is not running in a fire rated shaft, a firestop and

support is required.

• Terminate the vent system at least 0.6m (2')

above, but not more than 1.8m (6') above the

roof line, or according to the vent pipe

manufacturer's instructions.

• Terminate the vent system at least 0.6m (2')

above any portion of a building located within

3m (10') horizontally.

• Provide vertical support every 3.6m (12') or as

required by the vent pipe manufacturer's in-

structions.

• Slope the horizontal vent 1/4" for every 300m

(12") towards the drain tee.

• Do not vent straight upwards.

Always have a horizontal section of venting.

• Install a condensation drain in the horizontal

section of the venting.

Horizontal Vent Termination

• Terminate at least 300mm (12") above

grade or above snow line.

• Terminate at least 2.1m (7') above a public

walkway, 1.8m (6') from the combustion air

intake of any appliance, and 0.9m (3') from

any other building opening, gas utility meter,

service regulator etc.

• Terminate at least 0.9m (3') above any

forced air inlet within 3m (10'), 1.2m (4') be-

low, 1.2m (4') horizontally from or 0.3m (1')

above any door, window, or gravity air inlet

into any building per National Fuel Gas Code

ANSI Z223.1/NFPA 54.

• Slope the horizontal vent 1/4" downwards

for every 300m (12").

• Use a condensation drain if necessary.

•In the Commonwealth of Massachusetts a

carbon monoxide detector is required for all

side wall horizontally vented gas fuel equip-

ment. Please refer to Technical Bulletin TB

010606 for full installation instructions.

Appliance

Adapter*

Elbow

Hanger

Straps

Wall

Thimble

Ter mination

**0.3m (1') Min. -

0.9m (3') Max.

Slope vent

Downwards

* Adapter not required when

using Noritz N-Vent.

** 0.3m (1') minimum recommended,

but not required. Avoid installing

elbow directly on flue.

07.1.5, 4:34 PMPage 14

• Provide two permanent openings to allow

circulation of combustion air.

• Make each opening 199 square inches if they

provide indoor air, and 100 square inches for

outdoor air.

• If the unit is installed in a mechanical closet,

provide a 600mm (24") clearance in front of

the unit to the door.

• If combustion air will be provided through a

duct, size the duct to provide 60 cubic feet of

fresh air per minute.

Supply combustion air to the units as per the National Fuel Gas Code, ANSI Z223.1 and

in Canada, in accordance with NSCNGPIC.

Combustion Air

Openings supplying indoor air

250mm (10")

500mm (20")

07.1.5, 4:34 PMPage 15

Gas Meter

Select a gas meter capable of supplying the entire

btuh demand of all gas appliances in the building.

Gas Connection

•Do not use piping with a diameter smaller than

the inlet diameter of the water heater.

• Gas flex lines are not recommended unless they

are rated for 199,900 btuh.

• Install a gas shutoff valve on the supply line.

• Use only approved gas piping materials.

Follow the instructions from the gas supplier.

Gas Pressure

Size the gas line according to total btuh demand

of the building and length from the meter or

regulator so that the following supply pressures

are available even at maximum demand:

Natural Gas Supply Pressure

Min. 4" WC

Max. 10.5" WC

LP Gas Supply Pressure

Min. 8" WC

Max. 14" WC

Gas Piping

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system

during any pressure testing of that system at test pressures in excess of

⁄2 psi (3.5 kPa).

The Appliance must be isolated from the gas supply piping system by closing its individual manual shutoff

valve during any pressure testing of the gas supply piping system at test pressures equal to or less than

⁄2

psi (3.5 kPa).

The appliance and its gas connections must be leak tested before placing the appliance in operation.

The inlet gas pressure must be within the range specified. This is for the purposes of input adjustment.

In order to choose the proper size for the gas line, consult local codes or the National Fuel Gas Code ANSI

Z223.1.

Natural Gas

Meter

**See next page for the pipe capacity charts.

Noritz Gas Water Heater

(199,900 Btuh)

Clothes Dryer

(35,000 Btuh)

Barbecue

(50,000 Btuh)

Gas Range Stove

(65,000 Btuh)

3m (10')

1.5m (5')

3m (10')

Gas Fireplace

(25,000 Btuh)

Instructions

1. Size each outlet branch starting from the furthest

using the Btuh required and the length from the

meter.

2. Size each section of the main line using the

length to the furthest outlet and the Btuh

required by everything after that section.

Sample Gas Line

Sample Calculation

Outlet A: 13.5m (45') (Use 15m (50')), 50,000 Btuh requires 1/2"

Outlet B: 12m (40'), 65,000 Btuh requires 1/2"

Section 1: 13.5m (45') (Use 15m (50')), 115,000 Btuh requires 3/4"

Outlet C: 9m (30'), 35,000 Btuh requires 1/2"

Section 2: 13.5m (45') (Use 15m (50')), 150,000 Btuh requires 3/4"

Outlet D: 7.5m (25') (Use 9m (30')), 25,000 Btuh requires 1/2"

Section 3: 13.5m (45') (Use 15m (50')), 175,000 Btuh requires 1"

Outlet E: 7.5m (25') (Use 9m (30')), 199,900 Btuh requires 3/4"

Section 4: 13.5m (45') (Use 15m (50')), 374,900 Btuh requires 1-1/4"

Section 3 Section 2

Section 1

Outlet A

Outlet B

Outlet C

Outlet D

Outlet E

1.5m (5') 1.5m (5')

Section 4

Measuring Gas Pressure

In order to check the gas supply pressure to the unit, a

tap is provided on the gas inlet. Remove the hex head

philips screw from the tap, and connect a manometer

using a silicon tube.

In order to check the gas manifold pressure, a pair of

taps are provided on the gas valve inside the unit.

The pressure can be checked either by removing the hex

head philips screw and connecting a manometer with a

silicon tube, or by removing the 1/8" NPT screw with an

allen wrench and connecting the appropriate pressure

gauge.

07.1.5, 4:34 PMPage 16

Gas Line Sizing for a Noritz Gas Water Heater

Maximum Natur

Natur

al Gas Delivery Capacity in Cubic Feet per Hour (0.60 Specific Gravity, 0.5" WC Pressure Drop)

Contact the Gas Supplier for Btu/Cubic Ft. of the Supplied Gas. 1000 BTU/Cubic Ft. is a Typical Value

Maximum Liquified P

Liquified P

etroleum (Undiluted) Delivery Capacity in Thousands of Btuh (0.5" WC Pressure Drop)

Length in Feet

Pipe

Size

Pipe

Size

1/2"

3/4"

1 1/4"

1 1/2"

2 1/2"

3 1/2"

174

363

684

1404

2103

4050

6455

11,412

16,709

23,277

119

249

470

965

1445

2784

4437

7843

11,484

15,998

200

377

775

1161

2235

3563

6299

9222

12,847

Adapted from UPC 1997

171

323

663

993

1913

3049

5391

7893

10,995

152

286

588

880

1696

2703

4778

6995

9745

138

259

532

798

1536

2449

4329

6338

8830

127

239

490

734

1413

2253

3983

5831

8123

56 53 50 44

118 111 104 93

222 208 197 174

456

683

1315

2096

3705

5425

7557

428

641

1234

1966

3476

5090

7091

404

605

1165

1857

3284

4808

6698

358

536

1033

1646

2910

4261

5936

275

567

1071

2205

3307

6221

189

393

732

1496

2299

4331

152

315

590

1212

1858

3465

129

267

504

1039

1559

2992

114

237

448

913

1417

2646

103

217

409

834

1275

2394

196

378

771

1181

2205

185

346

724

1086

2047

173

322

677

1023

1921

162

307

630

976

1811

146

275

567

866

1606

132

252

511

787

1496

112

213

440

675

1260

Maximum Capacity of Flex TracPipe in Cubic Feet per Hour of Natural Gas (0.60 Specific Gravity, 0.5" WC Pressure Drop)

Length in Feet

Pipe

Size

3/4"

1 1/4"

1 1/2"

206

383

614

1261

2934

147

269

418

888

2078

121

218

334

723

1698

105

188

284

625

1472

168

251

559

1317

153

227

509

1203

141

209

471

1114

132

194

440

1042

125

181

415

983

118

171

393

933

137

320

762

116

277

661

Maximum Capacity of Flex TracPipe in Thousands of Btuh Liquified Petroleum ( 0.5" WC Pressure Drop)

Length in Feet

Pipe

Size

3/4"

1 1/4"

1 1/2"

325

605

971

1993

4638

232

425

661

1404

3285

191

344

528

1143

2684

166

297

449

988

2327

149

265

397

884

2082

136

241

359

805

1902

126

222

330

745

1761

118

208

307

696

1647

112

197

286

656

1554

106

186

270

621

1475

143

217

506

1205

129

183

438

1045

** For reference only. Please consult gas pipe manufacturer for actual pipe capacities.

Maximum Capacity for Gas Flex Connectors in Cubic Feet per Hour of Natural Gas (0.60 Specific Gravity, 0.5" WC Pressure Drop)

Length in Inches

Pipe

Size

1/2"

3/4"

1 1/4"

180 150

290

581

1470

125

255

512

1200

106

215

442

1130

197

397

960

173

347

930

Length in Inches

Pipe

Size

1/2"

3/4"

1 1/4"

288 240

465

930

2352

200

409

825

1920

169

344

708

1808

149

315

638

1536

137

278

556

1488

Maximum Capacity for Gas Flex Connectors in Thousands of Btuh Liquified Petroleum ( 0.5" WC Pressure Drop)

** For reference only. Please consult gas pipe manufacturer for actual pipe capacities.

TracPipe® is a registered trademark of Omega Flex.

3m (10')

6m (20') 9m (30')

12m (40') 15m (50') 18m (60') 21m (70') 24m (80') 27m (90')

37.5m (125')

30m (100')

3m (10')

6m (20') 9m (30')

12m (40') 15m (50') 18m (60') 21m (70') 24m (80') 27m (90') 30m (100') 60m (200')

37.5m (125') 45m (150')

60m (200')

3m (10')

6m (20') 9m (30')

12m (40') 15m (50') 18m (60') 21m (70') 24m (80') 27m (90') 30m (100') 45m (150')

60m (200')

3m (10')

6m (20') 9m (30')

12m (40') 15m (50') 18m (60') 21m (70') 24m (80') 27m (90') 30m (100') 45m (150')

300mm (12") 600mm (24") 900mm (36") 1200mm (48") 1500mm (60") 1800mm (72")

07.1.5, 4:34 PMPage 17

10.

Water Piping

This appliance suitable for potable water and space heating applications. Do not use this appliance if any part has

been underwater. Immediately call a qualified service technician to inspect the appliance and replace any part of the

control system and gas control which has been under water.

If the water heater is installed in a closed water supply system, such as one having a backflow preventer in the cold

water supply line, means shall be provided to control thermal expansion. Contact the water supplier or a local plumb-

ing inspector on how to control this situation.

A pressure relief valve must be installed near the hot water outlet that is rated in accordance with and complying with

either The Standard for Relief Valves and Automatic Shutoff Devices for Hot Water Supply Systems, ANSI Z21.22, or

The ANSI/ASME Boiler and Pressure Vessel Code, Section IV ( Heating Boilers ). This pressure relief valve must

be capable of an hourly Btu rated temperature steam discharge of 199,900 Btuh. Multiple valves may be used. The

pressure relief capacity must not exceed 150 psig. No valve shall be placed between the relief valve and the water

heater. The relief valve must be installed such that the discharge will be conducted to a suitable place for disposal

when relief occurs. No reducing coupling or other restriction may be installed in the discharge line. The discharge line

must be installed to allow complete drainage of both the valve and the line. If this unit is installed with a separate

storage vessel, the separate vessel must have its own temperature and pressure relief valve. This valve must also

comply with The Standard for Relief Valves and Automatic Gas Shutoff Devices for Hot Water Supply Systems, ANSI

Z21.22. (in the U.S. only). A temperature relief valve is not required, but if one is used, do not install the valve with the

probe directly in the flow of water. This may cause unwarranted discharge of the valve.

Piping and components connected to the water heater shall be suitable for use with potable water.

Toxic chemicals, such as those used for boiler treatment, shall not be introduced into the potable water.

A water heater used to supply potable water may not be connected to any heating system or components previously

used with a nonpotable water heating appliance.

When water is required in one part of the system at a higher temperature than in the rest of the system, means such

as a mixing valve shall be installed to temper the water to reduce the scald hazard.

• Flush water through the pipe to clean out metal powder, sand and dirt before connecting it.

• Take appropriate heat insulation measures (e.g., wrapping with heat insulation materials, using electric heaters)

according to the climate of the region to prevent the pipe from freezing.

•

Use a union coupling or flexible pipe for connecting the pipes to reduce the force applied to the piping.

• Do not use piping with a diameter smaller than the coupling.

• When feed water pressure is too high, insert a depressurizing valve, or take

water hammer prevention measure.

• Avoid using joints as much as possible to keep the piping simple.

• Avoid piping in which an air holdup can occur.

• If installing the unit on a roof:

• About lower-level hot water supply

If the unit is installed on a roof to supply water to the levels below, make sure that the water pressure supplied to

the unit does not drop below 29 psi. It may be necessary to install a pump system to ensure that the water pressure

is maintained at this level.

Check the pressure before putting the unit into operation.

Failure to supply the proper pressure to the unit may result in noisy operation, shorter lifetime of the unit, and may

cause the unit to shut down frequently.

Supply water piping

•

Do not use PVC, iron, or any piping which has been

treated with chromates, boiler seal or other chemicals.

•

Mount a check valve and a shut off valve (near the inlet).

• In order for the client to use the water heater

comfortably, 98.1 to 491 kPa (14 to 70 PSI) of

pressure is needed from the water supply.

Be sure to check the water pressure. If the water

pressure is low, the water heater cannot perform

to its full capability, and may become a source of

trouble for the client.

Drain piping

• Expansion water may drop from the pressure

prevention device and wet the floor. If neces-

sary, provide drain piping or use a drain hose to

remove the water.

Hot water piping

• Do not use lead, PVC, iron or any piping which

has been treated with chromates, boiler seal or

other chemicals.

• The longer the piping, the greater the heat loss.

Try to make the piping as short as possible.

• Use mixing valves with low water resistance. Use

shower heads with low pressure loss.

• If necessary, use a pump or other means to en-

sure that the supply water pressure to the inlet of

the heater does not fall below 29 PSI when the

maximum amount of water is being demanded.

Also install a pressure meter on the inlet. If this is

not done, local boiling will occur inside the water

heater causing abnormal sounds and decreasing

the durability of the heat exchanger.

Installation and service must be performed by a qualified plumber. In the

Commonwealth of Massachusetts, this product must be installed by a licensed

plumber or gas fitter in accordance with the Massachusetts Plumbing and Fuel

Gas Code 248 CMR Sections 2.00 and 5.00. Observe all applicable codes.

07.1.5, 4:34 PMPage 18

11. Plumbing Applications

Pump Control Signal

(See p. 23)

(See notes for Sizing)

Pump Control signal

(See p. 23)

Recirculation System

Pump

Fixtures

Cold Water Supply

Check

Valve

Hot Water Return

Check Valve

Pressure

Relief

Valve

Hot Water

Shutoff Valve

Drain

Use Honeywell Aquastat

(Model L6006A or L6006C)

Pump

AC120

Aquastat Wiring

105

Neutral

Ground

Live

Heating System

Cold Water Supply

Check

Valve

Hot Water Return

Pressure

Relief Valve

Hot Water

Drain

Air Scoop

(Optional)

Temp. &

Press. Gauge

(Optional)

Hydronic Heat

Exchanger or

Radiant Heat

Piping

Pressure

Reducing

Valve

(Optional)

Shutoff

Valve

Backflow

Preventer

(Optional)

Boiler Drain Valve

Heating

Controls

Mixing Valve

Cold Water Supply

Tempered Potable Hot Water

Hot Water for Heating

If the system requires water

for space heating at a higher

temperature than for other

uses, means such as a mixing

valve shall be provided to

temper the water for the other

uses to help prevent scalding.

For Space Heating Purposes:

Check Valve

Aquastat

(Use Aquastat if Unit Isn't

Controlling Pump)

Aquastat

(Use Aquastat if

Unit Isn't Controlling

Pump)

Pump

Expansion Tank

(Install According

to Local Codes)

Optional 30 - 38L

(8-10 Gal.)

Storage Tank

(To Alleviate Cold

Water Sandwich)

(See p. 23)

(Install According

to Local Codes)

(Relay for

Pump

> 85 W)

(See notes for Sizing)

Expansion

Tank

For Baseboard

Applications:

Please contact

Noritz for

compatibility.

(Relay for

Pump

> 85 W)

Shutoff Valve

NORITZ

Gas Water

Heater

NORITZ

Gas Water

Heater

Gas

Water

Heater

* Size the pump to provide at least 6L/min. (1.58 GPM) through the system at 30kPa (10')

of Head plus piping losses. Check the maintenance monitors on the unit to make sure the

pump is providing that much flow.

** Adjust the flow using a gate valve and verify the flow rate with the maintenance monitors.

* Size the pump to provide at least 6L/min. (1.58 GPM) through the system at 30kPa (10') of

Head plus piping losses. Check the maintenance monitors on the unit to make sure the

pump is providing that much flow.

** Adjust the flow using a gate valve and verify the flow rate with the maintenance monitors.

07.1.12, 3:13 PMPage 19

Do not connect electrical power to the unit until all electrical wiring has been completed.

1.Unscrew the junction box and slide it out of the unit..

2.Push the power cord through the bottom of the unit.

3.Connect the live and neutral wires to the black and

white wire in the junction box.

Screw the ground wire to the ground screw on the

back in the junction box and replace the junction box.

Consult a qualified electrician

for the electrical work.

12.

Electrical Wiring

This appliance must be electrically grounded in accordance with local codes, or in the absence of local codes,

with the National Electrical Code, ANSI/NFPA 70. In Canada, the latest CSA C22.1 Electrical Code.

Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper

and dangerous operation.

Verify proper operation after servicing.

Field wiring to be performed at time of appliance installation.

• The electrical supply required by the water heater is 120V

AC at 60 Hz.

The power consumption may be up to 125W or higher if

using optional accessories.

Use an appropriate circuit.

• Do not disconnect the power supply when not in use. When

the power is off, the freeze prevention in the water heater

will not activate, resulting in possible freezing damage.

•Do not let the power cord contact the

gas piping.

Tie the redundant power cord out-

side the water heater. Putting the

redundant length of cord inside the

water heater may cause electrical

interference and faulty operation.

Ground

• To prevent electrical shock, provide a ground

with resistance less than 100 . An electrician

should do this work.

•A grounding screw is provided on the back in

the junction box.

Do not connect the ground to the city water

or gas piping. Do not tie the ground to a tele-

phone line.

Breaker Installation

• Mount a device which shuts off the electrical

path automatically (leakage breaker) when

electrical leakage is detected.

Disconnect Power

Electrical Shock Hazard

Do not turn power on until electrical wiring is finished. Disconnect power before servicing.

Failure to do so may result in death or serious injury from electrical shock.

WARNING

Electrostatic discharge can affect electronic components. Take precautions to prevent electrostatic discharges from

personnel or hand tools during the water heater installation and servicing to protect product’s electronic control.

CAUTION

Junction Box

Power Cord

Ground

07.1.5, 4:34 PMPage 20

La page charge ...

Pentax N-0751M-OD Guide d'installation

Marque: Pentax

Modèle: N-0751M-OD

Catégorie: Chauffe-eau

Taper: Guide d'installation

Ce manuel convient également à

N-0751M

Télécharger le PDF

rapport

dans d''autres langues

English: Pentax N-0751M-OD Installation guide

Documents connexes

Pentax N-0751M-OD Manuel utilisateur

Pentax N-0751M-OD Guide d'installation

Ce manuel convient également à

Pentax N-0751M-OD Guide d'installation

dans d''autres langues

Documents connexes

Autres documents