Ryobi p546 Manuel utilisateur

Cette scie à chaîne a été conçue et fabriquée conformément

aux strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenue, elle vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le

manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

Su motosierra inalámbrica ha sido diseñada y fabrica-

da de conformidad con nuestras estrictas normas para

brindar fiabilidad, facilidad de uso y seguridad para el opera-

dor. Con el debido cuidado, le brindará muchos años de sólido

y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your chain saw has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

40 VOLT CHAIN SAW

SCIE À CHAÎNE 40 V

MOTOSIERRA DE 40 V

RY40500

2

 Introduction .......................................................................................................................................2

Introduction / Introducción

 General Power Tool Safety Warnings ............................................................................................ 3-4

Avertissements règles de sécurité relatives aux outils électriques / Advertencias de seguridad para herramientas eléctricas

Chain Saw Safety Warnings .......................................................................................................... 5-9

Avertissements de sécurité relatifs au scie à chaîne

/ Advertencias de seguridad de la motosierra

Symbols .................................................................................................................................... 10-11

Symboles / Símbolos

 Glossary of Terms ............................................................................................................................12

Glossaire / Glosario de términos

 Features ..................................................................................................................................... 13-14

Caractéristiques / Características

 Assembly ................................................................................................................................... 14-15

Assemblage / Armado

 Operation ................................................................................................................................... 15-23

Utilisation / Funcionamiento

 Maintenance .............................................................................................................................. 24-31

Entretien / Mantenimiento

 Bar and Chain Combinations ..........................................................................................................32

Combinaisons de guide et chaîne / Combinations de barra y cadena

 Troubleshooting ............................................................................................................................... 32

Dépannage / Corrección de problemas

 Warranty ..........................................................................................................................................33

Garantie / Garantía

 Parts Ordering and Service ............................................................................................... Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance,

and dependability have been given top priority in the design of this product making it easy to maintain

and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfai-

sante. Lors de la conception de ce produit, l’accent a été mis sur la sécurité, les performances et la

fiabilité, afin d’en faire un outil facile à utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el

diseño de este producto se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo

cual se facilita su manejo y mantenimiento.

3 - English

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions

may result in electric shock, fire and/or serious

injury.

Save all warnings and instructions for future

reference.The term “power tool” in the warnings

refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a

GFCI reduces the risk of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the influence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the

switch is in the off-position before connect-

ing to power source and/or battery pack,

picking up or carrying the tool. Carrying power

tools with your finger on the switch or energis-

ing power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce dust-

related hazards.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

GENERAL POWER TOOL SAFETY RULES

4 - English

GENERAL POWER TOOL SAFETY RULES

Do not use the power tool if the switch does

not turn it on and off. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may affect

the power tool’s operation. If damaged, have

the power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

BATTERY TOOL USE AND CARE

Recharge only with the charger specified by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of

fire when used with another battery pack.

Use power tools only with specifically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and fire.

When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small

metal objects, that can make a connection

from one terminal to another. Shorting the

battery terminals together may cause burns or

a fire.

Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery

may cause irritation or burns.

SERVICE

Have your power tool serviced by a qualified

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

When servicing a power tool, use only iden-

tical replacement parts. Follow instructions

in the Maintenance section of this manual.

Use of unauthorized parts or failure to follow

Maintenance instructions may create a risk of

shock or injury.

5 - English

Keep all parts of the body away from the

saw chain when the chain saw is operating.

Before you start the chain saw, make sure

the saw chain is not contacting anything. A

moment of inattention while operating chain

saws may cause entanglement of your clothing

or body with the saw chain.

Always hold the chain saw with your right

hand on the rear handle and your left hand on

the front handle. Holding the chain saw with a

reversed hand configuration increases the risk

of personal injury and should never be done.

Hold the power tool by insulated gripping

surfaces only, because the saw chain may

contact hidden wiring. Saw chains contacting

a “live” wire may make exposed metal parts of

the power tool “live” and could give the operator

an electric shock.

Wear safety glasses and hearing protec-

tion. Further protective equipment for head,

hands, legs and feet is recommended.

Adequate protective clothing will reduce per-

sonal injury by flying debris or accidental con-

tact with the saw chain.

Do not operate a chain saw in a tree. Opera-

tion of a chain saw while up in a tree may result

in personal injury.

Always keep proper footing and operate

the chain saw only when standing on fixed,

secure and level surface. Slippery or unstable

surfaces such as ladders may cause a loss of

balance or control of the chain saw.

When cutting a limb that is under tension be

alert for spring back. When the tension in the

wood fibres is released the spring loaded limb

may strike the operator and/or throw the chain

saw out of control.

Use extreme caution when cutting brush and

saplings. The slender material may catch the

saw chain and be whipped toward you or pull

you off balance.

Carry the chain saw by the front handle with

the chain saw switched off and away from

your body. When transporting or storing the

chain saw always fit the guide bar cover.

Proper handling of the chain saw will reduce the

likelihood of accidental contact with the moving

saw chain.

Follow instructions for lubricating, chain ten-

sioning and changing accessories. Improperly

tensioned or lubricated chain may either break

or increase the chance for kickback.

Keep handles dry, clean, and free from oil

and grease. Greasy, oily handles are slippery

causing loss of control.

Cut wood only. Do not use chain saw for

purposes not intended. For example: do not

use chain saw for cutting plastic, masonry

or non-wood building materials. Use of the

chain saw for operations different than intended

could result in a hazardous situation.

CAUSES AND OPERATOR

PREVENTION OF KICKBACK

Kickback may occur when the nose or tip of the

guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden

reverse reaction, kicking the guide bar up and back

towards the operator.

Pinching the saw chain along the top of the guide

bar may push the guide bar rapidly back towards

the operator.

Either of these reactions may cause you to lose

control of the saw which could result in serious

personal injury. Do not rely exclusively upon the

safety devices built into your saw. As a chain saw

user, you should take several steps to keep your

cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incor-

rect operating procedures or conditions and can

be avoided by taking proper precautions as given

below:

Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both

hands on the saw and position your body and

arm to allow you to resist kickback forces.

Kickback forces can be controlled by the opera-

tor, if proper precautions are taken. Do not let

go of the chain saw.

Do not overreach and do not cut above shoul-

der height. This helps prevent unintended tip

contact and enables better control of the chain

saw in unexpected situations.

CHAIN SAW SAFETY WARNINGS

6 - English

CHAIN SAW SAFETY WARNINGS

Do not use the chain saw in damp or wet loca-

tions.

Always be aware of extension cord while oper-

ating chain saw. Take precautions to avoid

tripping over cord. Keep cord away from chain

and operator at all times. Never carry saw by

the cord or pull it to disconnect from receptacle.

Keep cord from oil and sharp edges.

Stay alert and pay attention to what you are

doing. Use common sense when using this unit.

Keep all parts of your body away from the saw

chain when the unit is running.

Never let anyone use your chain saw who has

not received adequate instructions in its proper

use. This applies to rentals as well as privately

owned saws.

Before you start the unit, make sure the saw

chain is not contacting any object.

Stop the chain saw before setting it down.

To avoid accidental starting, never carry the unit

with your finger on the switch trigger.

Maintain the unit with care. Keep the cutting

edge sharp and clean for best performance and

to reduce the risk of injury. Follow instructions

for lubricating and changing accessories.

Do not operate a chain saw with one hand! Use

a firm grip with thumbs and fingers encircling the

chain saw handles. Serious injury to the opera-

tor, helpers, bystanders, or any combination

of these persons may result from one-handed

operation. A chain saw is intended for two-

handed use.

Guard against electric shock - Avoid body con-

tact with grounded surfaces such as metal pipes

and wire fences. There is an increased risk of

electric shock if your body is grounded.

Do not operate a chain saw that is damaged,

improperly adjusted, or not completely and

securely assembled. Chain should slow to a

stop when the switch trigger is released. If the

chain continues to turn after the switch trigger

has been released, have the unit serviced by an

authorized service center.

Check for damaged parts. Check for alignment

of moving parts, binding of moving parts, break-

age of parts, mounting, and any other condi-

tions that may affect its operation. A guard or

Only use replacement bars and chains

specified by the manufacturer. Incorrect

replacement bars and chains may cause chain

breakage and/or kickback.

Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

 Do not start cutting until you have a clear work

area, secure footing, and a planned retreat path

from the falling tree. Cluttered areas invite acci-

dents.

Keep ALL children, bystanders, visitors, and

animals out of the work area while starting or

cutting with the chain saw. Do not let visitors

contact chain saw or extension cord.

Do not operate chain saw in explosive atmo-

spheres, such as in the presence of flammable

liquids, gases, or dust. Chain saws create

sparks which may ignite the dust or fumes.

Dress Properly - Wear snug fitting clothing.

Always wear heavy, long pants, long sleeves,

overalls, jeans or chaps made of cut resistant

material or ones that contain cut resistant

inserts. Wear non-slip safety footwear. Wear

non-slip heavy duty gloves to improve your

grip and to protect your hands. Do not wear

jewelry, short pants, sandals, or go barefoot.

Do not wear loose fitting clothing, which could

be drawn into the motor or catch the chain or

underbrush. Secure hair so it is above shoulder

level. Wear hearing and head protection.

 Heavy protective clothing may increase operator

fatigue, which could lead to heat stroke. Dur-

ing weather that is hot and humid, heavy work

should be scheduled for early morning or late

afternoon hours when temperatures are cooler.

Always wear eye protection with side shields

marked to comply with ANSI Z87.1 as well as

head and hearing protection when operating

this equipment.

Always be aware of what you are doing when

using the chain saw. Use common sense. Do

not operate the chain saw when you are tired,

ill, or under the influence of alcohol, drugs, or

medication.

Do not expose the chain saw to rain.

7 - English

CHAIN SAW SAFETY WARNINGS

other part that is damaged should be properly

repaired or replaced by an authorized service

center unless otherwise indicated elsewhere in

this manual.

All chain saw service, other than the items listed

in the operation and maintenance sections,

should be performed by an authorized service

center.

Always maintain a proper stance.

Do not use chain saw if switch does not turn it

on and off. Have defective switch replaced by

an authorized service center.

Do not adapt your powerhead to a bow guide

or use it to power any attachments or devices

not listed for the saw.

Disconnect chain saw from power supply when

not in use, before servicing, and when making

adjustments and changing attachments, such

as saw chain and guard.

Do not cut vines and/or small underbrush.

Do not operate a chain saw in a tree, on a ladder,

rooftop, scaffold, or other unstable support; this

is extremely dangerous.

NOTE: The size of the work area depends on the

job being performed as well as the size tree or

work piece involved. For example, felling a tree

requires a larger work area than making bucking

cuts.

Do not force the chain saw. The job can be per-

formed better and safer at the rate for which it

was intended.

Always use the right product for your applica-

tion. The chain saw should be used for cutting

wood only. Never use the chain saw to cut plas-

tic, masonry or non-wood building materials.

Store chain saw when not in use. Chain saw

should be stored in a dry and high or locked

area out of the reach of children. When storing

chain saw place the scabbard on the bar and

chain and store the chain saw in carrying case.

 Use only with battery and charger listed. For use

with 40V lithium-ion battery packs. See Tool/

Appliance/Battery Pack/Charger Correlation

Supplement 988000842.

NOTE: Although the chain saw will work

with all battery packs listed on the correla-

tion supplement, for best performance, avoid

using first generation Ryobi 40V lithium-ion

batteries [OP4026 (part numbers 130186012

or 130186006) and OP4015 (part number

1300208001)]. The chain speed will be signifi-

cantly reduced if these batteries are used.

 Battery operated units do not have to be

plugged into an electrical outlet; therefore, they

are always in operating condition. Be aware

of possible hazards even when unit is not

operating.

 Remove the battery pack from the chain saw

before cleaning, servicing, storing, removing

material from the unit, changing accessories

such as the bar and chain, or when not in use.

Save these instructions. Refer to them fre-

quently and use them to instruct others who

may use this product. If you loan someone this

product, loan them these instructions also.

8 - English

KICKBACK

See Figures 1 - 4.

 WARNING: Kickback may occur when the

moving chain contacts an object at the upper

portion of the tip of the guide bar or when the

wood closes in and pinches the saw chain in

the cut. Contact at the upper portion of the tip

of the guide bar can cause the chain to dig into

the object and stop the chain for an instant.

The result is a lightning fast, reverse reaction

which kicks the guide bar up and back toward

the operator. If the saw chain is pinched along

the top of the guide bar, the guide bar can be

driven rapidly back toward the operator. Either

of these reactions can cause loss of saw control

which can result in serious injury. Do not rely

exclusively upon the safety devices built into

the saw. As a chain saw user, you should take

several steps to keep your cutting jobs free from

accident or injury.

 The following precautions should be followed

to minimize kickback:

• Always grip the saw firmly with both hands.

Hold the saw firmly with both hands when

the unit is running. Place your right hand on

the rear handle and your left hand on the

front handle with your thumbs and fingers

encircling the chain saw handles. A firm grip

together with a stiff left arm will help you

maintain control of the saw if kickback occurs.

• Make sure that the area in which you are cut-

ting is free from obstructions. Do not let the

nose of the guide bar contact a log, branch,

fence, or any other obstruction that could be

hit while you are operating the saw.

• Always cut with the unit running at full speed.

Fully squeeze the throttle trigger and maintain

a steady cutting speed.

• Use replacement parts such as low kickback

chain, chain brakes, SAFE-T-TIP

®

anti-kick-

back nose guards special guide bars that

reduce the risks associated with rotational

kickback. Use only the replacement guide

bars and low kickback chains specified by

the manufacturer for the saw.

Fig. 2

Fig. 3

Fig. 4

ROTATIONAL

KICKBACK

DANGER ZONE

PULL

PUSH

Fig. 1

SAFE-T-TIP®

ANTI-KICKBACK

NOSE GUARD

CHAIN SAW SAFETY WARNINGS

9 - English

 With a basic understanding of kickback, you

can reduce or eliminate the element of surprise.

Sudden surprise contributes to accidents.

 Keep proper footing and balance at all times.

 Do not cut above shoulder height or overreach

when cutting.

 Keep the SAFE-T-TIP® anti-kickback nose

guard properly mounted on the guide bar to

prevent rotational kickback

 Follow the sharpening and maintenance

instructions for the saw chain.

 Push and Pull - This reaction force is always

opposite to the direction the chain is moving

where wood contact is made. Thus, the operator

must be ready to control the PULL when cutting

on the bottom edge of the bar, and PUSH when

cutting along the top edge. See Figure 4.

UNDERSTANDING YOUR CHAIN SAW

SAFETY DEVICES

SAFE-T-TIP

®

ANTI-KICKBACK NOSE

GUARD

See Figure 1.

The SAFE-T-TIP

®

prevents kickback from hap-

pening, because it covers the tip of the bar where

kickback is generated. Never attempt any kind of

cutting where the SAFE-T-TIP

®

would have to be

removed from the bar tip.

LOW KICKBACK SAW CHAIN

The rakers (depth gauges) ahead of each cutter

can minimize the force of a kickback reaction by

preventing the cutters from digging in too deeply

at the kickback zone. Only use replacement chain

that is equivalent to original chain or has been

certified as low kickback chain per ANSI B175.1.

Low kickback saw chain is chain that has met

the kickback performance requirements of ANSI

B175.1 - 1991 (American National Standard

for Power Tools - Gasoline-Powered Chain

Saws-Safety Requirements) when tested on the

representative sample of chain saws below 3.8

c.i.d. specified in ANSI B175.1 - 1991.

As saw chains are sharpened during their useful

life, they lose some of the low kickback qualities

and extra caution should be used.

GUIDE BARS

Generally, guide bars with small radius tips have

somewhat lower kickback potentials.

When making a replacement, be sure to order

one of the RYOBI bars listed for the saw in this

operator’s manual.

The proper size SAFE-T-TIP

®

nose guard comes

installed on the bar. Use only guide bars that have

a provision for mounting the SAFE-T-TIP

®

.

CHAIN SAW SAFETY WARNINGS

SAVE THESE INSTRUCTIONS

10 - English

The following signal words and meanings are intended to explain the levels of risk associated with

this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not

avoided, will result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided,

could result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided,

may result in minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not

related to an injury hazard, such as a situation that may result in

property damage.

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and

understand operator’s manual before using this product.

Eye and Head Protec-

tion

Always wear eye protection with side shields marked

to comply with ANSI Z87.1, along with head protection

SAFE-T-TIP

®

Nose

Guard

The SAFE-T-TIP

®

nose guard on the guide bar helps

prevent rotational kickback.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Operate With Two

Hands

Hold and operate the saw properly with both hands.

One Handed Do not operate the saw using only one hand.

SYMBOLS

11 - English

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Kickback DANGER! BEWARE OF KICKBACK.

Bar Nose Contact Avoid bar nose contact.

Wear Gloves

Wear non-slip, heavy-duty protective gloves when

handling the chain saw.

Wear Safety Footwear

Wear non-slip safety footwear when using this

equipment.

Keep Bystanders

Away

Keep all bystanders and animals at least 50 ft. away.

Oil Indicator

Pour bar and chain lubricant into oil tank where

indicated. Do not use any other fluids.

Recycle Symbol

This product uses lithium-ion batteries. Local, state or

federal laws may prohibit disposal of batteries in ordinary

trash. Consult your local waste authority for information

regarding available recycling and/or disposal options.

V Volts Voltage

Direct Current Type or a characteristic of current

SYMBOLS

12 - English

GLOSSARY OF TERMS

Bucking

The process of cross cutting a felled tree or log

into lengths.

Chain Saw Powerhead

A chain saw without the saw chain and guide bar.

Drive Sprocket or Sprocket

The toothed part that drives the saw chain.

Felling

The process of cutting down a tree.

Felling Back Cut

The final cut in a tree felling operation made on

the opposite side of the tree from the notching

undercut.

Front Hand Guard

A structural barrier between the front handle of a

chain saw and the guide bar, typically located close

to the hand position on the front handle.

Front Handle

The support handle located at or toward the front

of the chain saw. This handle is for the left hand.

Guide Bar

A solid railed structure that supports and guides

the saw chain.

Kickback

The backward or upward motion, or both, of the

guide bar occurring when the saw chain near the

nose of the top area of the guide bar contacts any

object such as a log or branch, or when the wood

closes in and pinches the saw chain in the cut.

Kickback (Pinch)

The rapid pushback of the saw which can occur

when the wood closes in and pinches the moving

saw chain in the cut along the top of the guide bar.

Kickback (Rotational)

The rapid upward and backward motion of the

saw which can occur when the moving saw chain

near the upper portion of the tip of the guide bar

contacts an object, such as a log or branch.

Lock-out button

A movable stop that prevents the unintentional

operation of the switch until manually actuated.

Low-Kickback Chain

A chain that complies with the kickback perfor-

mance requirements of ANSI B175.1 when tested

on a representative sample of chain saws.

Normal Cutting Position

Those positions assumed in performing the buck-

ing and felling cuts.

Notching Undercut

A notch cut in a tree that directs the tree’s fall.

Rear Handle

The support handle located at or toward the rear

of the saw. It normally contains the switch trigger.

This handle is for the right hand.

Reduced Kickback Guide Bar

A guide bar which has been demonstrated to

reduce kickback significantly.

Replacement Saw Chain

A chain that complies with the kickback perfor-

mance requirements of ANSI B175.1 when tested

with specific chain saws. It may not meet the ANSI

performance requirements when used with other

saws.

SAFE-T-TIP® Nose Guard

An attachment that may be provided on the end

of the guide bar to prevent the chain at the end of

the guide bar from contacting the wood.

Saw Chain

A loop of chain having cutting teeth that cut the

wood, and that is driven by the motor and is sup-

ported by the guide bar.

Springpole

A small tree (sapling) or limb that is bent or trapped

under tension. It may “spring back” rapidly when

cut, causing a dangerous situation.

Switch Trigger

A device that when operated will complete or

interrupt an electrical power circuit to the motor

of the chain saw.

13 - English

FEATURES

PRODUCT SPECIFICATIONS

Motor ....................................................................................................................................40 Volt DC

Bar Length ....................................................................................................................................12 in.

Cutting Capacity.............................................................................................................................9 in.

Felling Capacity ..............................................................................................................................7 in.

Chain oil tank capacity .................................................................................................................. 5 oz.

NOTE: This saw was designed for occasional light duty use and has some limitations as to what it

can cut.

Fig. 5

CHAIN OIL

TANK CAP

REAR

HANDLE

FRONT HANDLE

GUIDE

BAR

LOW KICKBACK

CHAIN

TENSIONING KNOB

CHAIN COVER

LOCK KNOB

BATTERY PACK

FRONT HAND

GUARD

CHAIN

COVER

SWITCH TRIGGER

SCABBARD

BATTERY PACK

LOCK-OUT

BUTTON

SAFE-T-TIP©

QUICK VIEW OIL

INDICATOR

14 - English

FEATURES

KNOW YOUR CHAIN SAW

See Figure 5.

The safe use of this product requires an under-

standing of the information on the tool and in this

operator’s manual as well as a knowledge of the

project you are attempting. Before use of this prod-

uct, familiarize yourself with all operating features

and safety rules.

CHAIN TENSIONING KNOB

This feature allows user to adjust the tension of

the chain.

GUIDE BAR

The factory-equipped guide bar has a small radius

tip that offers a somewhat lower kickback potential.

LOW KICKBACK CHAIN

The low kickback chain helps minimize the force

of a kickback reaction by preventing the cutters

from digging in too deeply at the kickback zone.

QUICK VIEW OIL INDICATOR

Semi-transparent oil reservoir that allows user to

see when to add oil.

SAFE-T-TIP

®

ANTI-KICKBACK NOSE

GUARD

The SAFE-T-TIP

®

Anti-Kickback Nose Guard is an

attachment provided on the end of the guide bar

to prevent the chain on the end of the guide bar

from contacting the wood.

LOCK-OUT BUTTON

A control feature designed to prevent the motor

from being accidently started.

SWITCH TRIGGER

Squeeze the switch trigger to operate the unit after

switch lock-out has been pushed in. Release the

switch trigger to stop the unit.

ASSEMBLY

UNPACKING

This product has been shipped completely

assembled.

 Carefully remove the product and any acces-

sories from the box. Make sure that all items

listed in the packing list are included.

WARNING:

Do not use this product if any parts on the Pack-

ing List are already assembled to your product

when you unpack it. Parts on this list are not

assembled to the product by the manufacturer

and require customer installation. Use of a prod-

uct that may have been improperly assembled

could result in serious personal injury.

 Inspect the product carefully to make sure no

breakage or damage occurred during shipping.

 Do not discard the packing material until you

have carefully inspected and satisfactorily oper-

ated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Chain Saw with Scabbard

Bar and Chain Lubricant

Operator’s Manual

WARNING:

If any parts are damaged or missing do not

operate this product until the parts are replaced.

Use of this product with damaged or missing

parts could result in serious personal injury.

15 - English

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this

product. Any such alteration or modification is

misuse and could result in a hazardous condi-

tion leading to possible serious personal injury.

DANGER:

Never cut near power lines, electric cords, or

other electric sources. If bar and chain jams

on any electrical cord or line, DO NOT TOUCH

THE BAR OR CHAIN! THEY CAN BECOME

ELECTRICALLY LIVE AND VERY DANGEROUS.

Continue to hold the chain saw by the insulated

rear handle or lay it down and away from you in

a safe manner. Disconnect the electrical service

to the damaged line or cord before attempting

to free the bar and chain from the line or cord.

Contact with the bar, chain, other conductive

parts of the chain saw, or live electric cords or

lines will result in death by electrocution, electric

shock, or serious personal injury.

WARNING:

Do not allow familiarity with this product to

make you careless. Remember that a careless

fraction of a second is sufficient to inflict seri-

ous injury.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1, along with

head protection. Failure to do so could result in

objects being thrown into your eyes and other

possible serious injuries.

ASSEMBLY

OPERATION

WARNING:

Do not use any attachments or accessories

not recommended by the manufacturer of this

product. The use of attachments or accessories

not recommended can result in serious personal

injury.

WARNING:

Never fell a tree or cut a log or limb that has a

diameter greater that the length of the guide

bar. Only properly trained professionals should

perform these cuts. Performing these types of

cuts can cause an accident and result in death

or serious personal injury.

Before each use, inspect the entire product for

damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners

and caps and do not operate this product until all

missing or damaged parts are replaced. Please call

1-800-860-4050 or contact an authorized service

center for assistance.

APPLICATIONS

You may use this product for the following purposes:

Limbing and pruning branches from trees

Felling small trees up to 7 in. diameter

Bucking the fallen tree into shorter lengths

This product will accept Ryobi 40 V lithium-ion

battery packs.

For complete charging instructions, refer to the

Operator’s Manual for your Ryobi 40 V battery

pack and charger model.

WARNING:

To prevent accidental starting that could cause

serious personal injury, always remove the bat-

tery pack from the product when assembling

parts.

16 - English

TO INSTALL / REMOVE BATTERY PACK

See Figure 6.

WARNING:

Always remove battery pack from your tool

when you are assembling parts, making adjust-

ments, cleaning, carrying, transporting or when

not in use. Removing battery pack will prevent

accidental starting that could cause serious

personal injury.

NOTE: To avoid serious personal injury, always

remove the battery pack and keep hands clear of

the look-out button when carrying or transporting

the tool.

To install:

 Place the battery pack in your chain saw. Align

raised rib on battery pack with groove in chain

saw’s battery port.

NOTICE:

When placing battery pack in your chain saw,

be sure raised rib on battery pack aligns with

groove in chain saw’s battery port and latches

snap in place properly. Improper assembly of

battery pack can cause damage to internal

components.

 Make sure the latch on bottom side of the bat-

tery pack snaps in place and that battery pack is

secured in chain saw before beginning operation.

WARNING:

Make sure the latch on the bottom of the bat-

tery pack snaps in place and the battery pack

is fully seated and secure in the chain saw bat-

tery port before beginning operation. Failure

to securely seat the battery pack could cause

the battery pack to fall out, resulting in serious

personal injury.

To remove:

Locate latch on bottom of battery pack and depress

both sides to release the battery pack from the

chain saw.

OPERATION

NOTICE:

Remove battery pack from unit. Fill oil tank with

Ryobi Bar and Chain Lubricant before starting

the chain saw. Failure to lubricate the chain will

cause damage to the bar and chain.

CHAIN OIL SYSTEM

See Figure 7.

 Use Ryobi Bar and Chain Lubricant. It is formu-

lated to perform over a wide temperature range

with no dilution required.

NOTE: Do not use dirty, used or otherwise contam-

inated oils. Damage may occur to the bar or chain.

 Carefully pour the bar and chain oil into the tank.

 Check and fill the oil tank when battery is

recharged, or as needed.

NOTE: It is normal for lubricant to seep from the

saw when not in use. To prevent seepage, empty

the oil tank after each use. When storing the unit

for a long period of time (three months or longer) be

sure the chain is lightly lubricated; this will prevent

rust on the chain and bar sprocket.

Fig. 7

Fig. 6

BATTERY

PACK

LATCH

BATTERY

PORT

17 - English

STARTING AND STOPPING THE CHAIN

SAW

See Figure 8.

WARNING:

Keep body to the left of the chain line. Never

straddle the saw or chain, or lean over past the

chain line.

Starting the chain saw:

 Place the chain saw on a flat bare surface and

make sure no objects or obstructions are in

immediate vicinity which could come in contact

with the bar and chain.

 Press and hold the lock-out button. This makes

the switch trigger operational.

 Press and hold the switch trigger, release the

lock-out button and continue to squeeze the

switch trigger for continued operation.

Stopping the chain saw:

 Release the switch trigger to stop the chain saw.

 Upon release of the switch trigger, the lock-out

button will be automatically reset to the lock

position.

This cordless chain saw is not designed for cutting

trees larger than 7 in. in diameter.

This cordless chain saw is designed for limbing

and pruning type cutting, as well as cutting trees

up to 7 in. in diameter only.

Do not attempt to make any cut that would require

removal of the SAFE-T-TIP

®

.

PREPARATION FOR CUTTING

PROPER GRIP ON HANDLES

See Figures 9 - 11.

Refer to GENERAL POWER TOOL SAFETY

RULES earlier in this manual for appropriate safety

equipment.

 Wear non-slip gloves for maximum grip and

protection.

 Hold the saw firmly with both hands. Always

keep your left hand on the front handle and your

right hand on the rear handle so that your body

is to the left of the chain line.

OPERATION

Fig. 8

LOCK-OUT

BUTTON

SWITCH

TRIGGER

SWITCH

TRIGGER

LOCK-OUT

BUTTON

Fig. 9

18 - English

OPERATION

STRAIGHT ARM

POSITION

CHAIN LINE

WARNING:

Never use a left-handed (cross-handed) grip,

or any stance which would place your body or

arm across the chain line.

 Maintain a proper grip on the saw whenever

the unit is running. The fingers should encircle

the handle and the thumb is wrapped under the

handlebar. This grip is least likely to be broken

(by a kickback or other sudden reaction of the

saw). Any grip in which the thumb and fingers

are on the same side of the handle, is danger-

ous because a slight kick of the saw can cause

loss of control.

WARNING:

Do not operate the switch trigger with your left

hand and hold the front handle with your right

hand. Never allow any part of your body to be

in the chain line while operating a saw.

PROPER CUTTING STANCE

See Figures 12 - 13.

WARNING:

Always use the proper cutting stance described

in this section. Never kneel when using the

chain saw, except when felling a tree as illus-

trated in Figure 13. Kneeling could result in loss

of stability and control of the chain saw, result-

ing in serious personal injury.

 Weight should be balanced with both feet on

solid ground.

 Keep left arm with elbow locked in a “straight

arm” position to withstand any kickback force.

 Your body should always be to the left of the

chain line.

 Thumb should be on underside of handlebar.

BASIC CUTTING PROCEDURE

Practice cutting a few small logs using the following

technique to get the “feel” of using the saw before

you begin a major sawing operation.

Fig. 11

Fig. 10

Fig. 12

Fig. 13

19 - English

 Take the proper stance in front of the wood with

the saw off.

 Squeeze the switch trigger and let the chain

accelerate to full speed before entering the cut.

 Begin cutting with the saw against the log.

 Keep the unit running the entire time you are

cutting, maintain a steady speed.

 Allow the chain to cut for you; exert only light

downward pressure. If you force the cut, dam-

age to the bar, chain, or unit can result.

 Release the switch trigger as soon as the cut is

completed, allowing the chain to stop. If you run

the saw without a cutting load, unnecessary wear

can occur to the chain, bar, and unit.

 Do not put pressure on the saw at the end of cut.

WORK AREA PRECAUTIONS

See Figure 14.

 Cut only wood or materials made from wood, no

sheet metal, no plastics, no masonry, no non-

wood building materials.

 Never allow children to operate the saw. Allow no

person to use this chain saw who has not read this

Operator’s Manual or received adequate instruc-

tions for the safe and proper use of this chain saw.

 When felling a tree, keep everyone - helpers,

bystanders, children, and animals - a safe distance

from the cutting area. During felling operations, the

safe distance should be a least twice the height of

the largest trees in the felling area. During bucking

operations, keep a minimum distance of 15 feet

between workers. Trees should not be felled in a

manner that would endanger any person, strike

any utility line or cause any property damage. If

the tree does make contact with any utility line, the

utility company should be notified immediately.

 Always cut with both feet on solid ground to pre-

vent being pulled off balance.

 Do not cut above chest height, as a saw held high-

er is difficult to control against kickback forces.

 Do not fell trees near electrical wires or buildings.

Leave this operation for professionals.

 Cut only when visibility and light are adequate for

you to see clearly.

OPERATION

Fig. 14

45°

PLANNED LINE

OF FALL

RETREAT PATH

FELLING TREES

See Figures 14 - 17.

HAZARDOUS CONDITIONS

WARNING:

Do not fell trees during periods of high wind or

heavy precipitation. Wait until the hazardous

weather has ended.

WARNING:

Closely check for broken or dead branches,

which could fall while cutting and do not cut

near buildings or electrical wires if you do not

know the direction of tree fall. Do not cut at

night or during bad weather conditions, such as

rain, snow, or strong winds, which can reduce

visibility and control of the chain saw. If the tree

you are felling makes contact with any utility

line, you should discontinue use of the chain

saw and immediately notify the utility company.

Failure to follow these instructions could result

in death or serious personal injury.

20 - English

When felling a tree, it is important that you follow

these warnings and instructions to prevent pos-

sible serious injury.

■Do not cut down trees having an extreme lean or

large trees with rotten limbs, loose bark, or hol-

low trunks. Have these trees pushed or dragged

down with heavy equipment, then cut them up.

■Do not cut trees near electrical wires or buildings.

■Check the tree for damaged or dead branches

that could fall and hit you during felling.

■Periodically glance at the top of the tree during

the backcut to assure the tree is going to fall in

the desired direction.

If the tree starts to fall in the wrong direction,

or if the saw gets caught or hung up during the

fall, leave the saw and save yourself!



Felling a tree - When bucking and felling opera-

tions are being performed by two or more per-

sons, at the same time, the felling operation

should be separated from the bucking operation

by a distance of at least twice the height of the

tree being felled. Trees should not be felled in a

manner that would endanger any person, strike

any utility line or cause any property damage. If

the tree does make contact with any utility line, the

utility company should be notified immediately.

 Before any cuts are started, pick your escape

route (or routes in case the intended route is

blocked); clear the immediate area around the

tree and make sure there are no obstructions

in your planned path of retreat. Clear path of

safe retreat approximately 135° from planned

line of fall. The retreat path should extend back

and diagonally to the rear of the expected line

of fall. See Figure 14.

 Before felling is started, consider the force and

direction of the wind, the lean and balance of

the tree, and the location of large limbs. These

things influence the direction in which the tree

will fall. Do not try to fell a tree along a line dif-

ferent from its natural line of fall.

 The chain saw operator should keep on the

uphill side of the terrain as the tree is likely to

roll or slide downhill after it is felled.

 Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where felling cuts are to

be made.

OPERATION

Fig. 17

WEDGE

KICKBACK

Fig. 18

NOTCH

BACK CUT

Fig. 16

HINGE

2 in. OR 1/10 DIA

NOTCH -

APPROX. 1/3

DIAMETER OF

TRUNK

BACK CUT

2 in.

Fig. 15

La page charge ...

Ryobi p546 Manuel utilisateur

Ce manuel convient également à

Ryobi p546 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents