Ryobi RY40511 Le manuel du propriétaire

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

40 VOLT CHAIN SAW

SCIE À CHAÎNE 40 V

MOTOSIERRA DE 40 V

RY40502

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

TABLE OF CONTENTS

 General Power Tool Safety

Warnings ......................................... 2-3

 Chain Saw Safety Warnings ............ 4-7

 Symbols .......................................... 8-9

 Glossary of Terms .............................10

 Features ...................................... 11-12

 Assembly .................................... 12-13

 Operation .................................... 13-21

 Maintenance ............................... 22-28

 Bar and Chain Combinations ............ 28

 Troubleshooting ................................29

 Parts Ordering/Service ........ Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

TABLE DES MATIÈRES

 Avertissements règles de sécurité

relatives aux outils électriques ........ 2-3

 Avertissements de sécurité

relatifs au scie à chaîne ................... 4-7

 Symboles ........................................ 8-9

 Glossaire ...........................................10

 Caractéristiques .......................... 11-12

 Assemblage ................................ 12-13

 Utilisation .................................... 13-21

 Entretien ...................................... 22-28

 Combinaisons de guide et chaîne ....28

 Dépannage ........................................ 29

 Commande de pièces/

réparation .......................... Páge arrière

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe leer

y comprender el manual del operador

antes de usar este producto.

ÍNDICE DE CONTENIDO

 Advertencias de seguridad

para herramientas eléctricas ........... 2-3

 Advertencias de seguridad

de la motosierra .............................. 4-7

 Símbolos ......................................... 8-9

 Glosario de términos ......................... 10

 Características ............................ 11-12

 Armado ....................................... 12-13

 Funcionamiento .......................... 13-21

 Mantenimiento ............................ 22-28

 Combinaciones de barra y cadena ...28

 Correción de problemas ...................29

 Pedidos de piezas/

servicio ........................... Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

2 - English

GENERAL POWER TOOL SAFETY RULES

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions

may result in electric shock, fire and/or serious

injury.

Save all warnings and instructions for future

reference.The term “power tool” in the warnings

refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

WORK AREA SAFETY

Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a

GFCI reduces the risk of electric shock.

PERSONAL SAFETY

Stay alert, watch what you are doing and

use common sense when operating a power

tool. Do not use a power tool while you are

tired or under the influence of drugs, alcohol

or medication. A moment of inattention while

operating power tools may result in serious

personal injury.

Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the

switch is in the off-position before connect-

ing to power source and/or battery pack,

picking up or carrying the tool. Carrying power

tools with your finger on the switch or energis-

ing power tools that have the switch on invites

accidents.

Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of dust collection can reduce dust-

related hazards.

POWER TOOL USE AND CARE

Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

3 - English

Do not use the power tool if the switch does

not turn it on and off. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may affect

the power tool’s operation. If damaged, have

the power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

BATTERY TOOL USE AND CARE

Recharge only with the charger specified by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of

fire when used with another battery pack.

Use power tools only with specifically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and fire.

When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small

metal objects, that can make a connection

from one terminal to another. Shorting the

battery terminals together may cause burns or

a fire.

Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water.

If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery

may cause irritation or burns.

SERVICE

Have your power tool serviced by a qualified

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

When servicing a power tool, use only iden-

tical replacement parts. Follow instructions

in the Maintenance section of this manual.

Use of unauthorized parts or failure to follow

Maintenance instructions may create a risk of

shock or injury.

GENERAL POWER TOOL SAFETY RULES

4 - English

Keep all parts of the body away from the

saw chain when the chain saw is operating.

Before you start the chain saw, make sure

the saw chain is not contacting anything. A

moment of inattention while operating chain

saws may cause entanglement of your clothing

or body with the saw chain.

Always hold the chain saw with your right

hand on the rear handle and your left hand on

the front handle. Holding the chain saw with a

reversed hand configuration increases the risk

of personal injury and should never be done.

Hold the power tool by insulated gripping

surfaces only, because the saw chain may

contact hidden wiring. Saw chains contacting

a “live” wire may make exposed metal parts of

the power tool “live” and could give the operator

an electric shock.

Wear safety glasses and hearing protec-

tion. Further protective equipment for head,

hands, legs and feet is recommended.

Adequate protective clothing will reduce per-

sonal injury by flying debris or accidental con-

tact with the saw chain.

Do not operate a chain saw in a tree. Opera-

tion of a chain saw while up in a tree may result

in personal injury.

Always keep proper footing and operate

the chain saw only when standing on fixed,

secure and level surface. Slippery or unstable

surfaces such as ladders may cause a loss of

balance or control of the chain saw.

When cutting a limb that is under tension be

alert for spring back. When the tension in the

wood fibres is released the spring loaded limb

may strike the operator and/or throw the chain

saw out of control.

Use extreme caution when cutting brush and

saplings. The slender material may catch the

saw chain and be whipped toward you or pull

you off balance.

Carry the chain saw by the front handle with

the chain saw switched off and away from

your body. When transporting or storing the

chain saw always fit the guide bar cover.

Proper handling of the chain saw will reduce the

likelihood of accidental contact with the moving

saw chain.

Follow instructions for lubricating, chain ten-

sioning and changing accessories. Improperly

tensioned or lubricated chain may either break

or increase the chance for kickback.

Keep handles dry, clean, and free from oil

and grease. Greasy, oily handles are slippery

causing loss of control.

Cut wood only. Do not use chain saw for

purposes not intended. For example: do not

use chain saw for cutting plastic, masonry

or non-wood building materials. Use of the

chain saw for operations different than intended

could result in a hazardous situation.

CAUSES AND OPERATOR

PREVENTION OF KICKBACK

Kickback may occur when the nose or tip of the

guide bar touches an object, or when the wood

closes in and pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden

reverse reaction, kicking the guide bar up and back

towards the operator.

Pinching the saw chain along the top of the guide

bar may push the guide bar rapidly back towards

the operator.

Either of these reactions may cause you to lose

control of the saw which could result in serious

personal injury. Do not rely exclusively upon the

safety devices built into your saw. As a chain saw

user, you should take several steps to keep your

cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incor-

rect operating procedures or conditions and can

be avoided by taking proper precautions as given

below:

Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both

hands on the saw and position your body and

arm to allow you to resist kickback forces.

Kickback forces can be controlled by the opera-

tor, if proper precautions are taken. Do not let

go of the chain saw.

Do not overreach and do not cut above chest

height. This helps prevent unintended tip con-

tact and enables better control of the chain saw

in unexpected situations.

CHAIN SAW SAFETY WARNINGS

5 - English

Only use replacement bars and chains

specified by the manufacturer. Incorrect

replacement bars and chains may cause chain

breakage and/or kickback.

Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

 Do not start cutting until you have a clear work

area, secure footing, and a planned retreat path

from the falling tree. Cluttered areas invite acci-

dents.

Keep ALL children, bystanders, visitors, and

animals out of the work area while starting or

cutting with the chain saw. Do not let visitors

contact chain saw or extension cord.

Do not operate chain saw in explosive atmo-

spheres, such as in the presence of flammable

liquids, gases, or dust. Chain saws create

sparks which may ignite the dust or fumes.

Dress Properly - Wear snug fitting clothing.

Always wear heavy, long pants, long sleeves,

overalls, jeans or chaps made of cut resistant

material or ones that contain cut resistant

inserts. Wear non-slip safety footwear. Wear

non-slip heavy duty gloves to improve your

grip and to protect your hands. Do not wear

jewelry, short pants, sandals, or go barefoot.

Do not wear loose fitting clothing, which could

be drawn into the motor or catch the chain or

underbrush. Secure hair so it is above shoulder

level. Wear hearing and head protection.

 Heavy protective clothing may increase operator

fatigue, which could lead to heat stroke. Dur-

ing weather that is hot and humid, heavy work

should be scheduled for early morning or late

afternoon hours when temperatures are cooler.

Always wear eye protection with side shields

marked to comply with ANSI Z87.1 as well as

head and hearing protection when operating

this equipment.

Always be aware of what you are doing when

using the chain saw. Use common sense. Do

not operate the chain saw when you are tired,

ill, or under the influence of alcohol, drugs, or

medication.

Do not expose the chain saw to rain.

Do not use the chain saw in damp or wet loca-

tions.

Always be aware of extension cord while oper-

ating chain saw. Take precautions to avoid

tripping over cord. Keep cord away from chain

and operator at all times. Never carry saw by

the cord or pull it to disconnect from receptacle.

Keep cord from oil and sharp edges.

Stay alert and pay attention to what you are

doing. Use common sense when using this unit.

Keep all parts of your body away from the saw

chain when the unit is running.

Never let anyone use your chain saw who has

not received adequate instructions in its proper

use. This applies to rentals as well as privately

owned saws.

Before you start the unit, make sure the saw

chain is not contacting any object.

Stop the chain saw before setting it down.

To avoid accidental starting, never carry the unit

with your finger on the switch trigger.

Maintain the unit with care. Keep the cutting

edge sharp and clean for best performance and

to reduce the risk of injury. Follow instructions

for lubricating and changing accessories.

Do not operate a chain saw with one hand! Use

a firm grip with thumbs and fingers encircling the

chain saw handles. Serious injury to the opera-

tor, helpers, bystanders, or any combination

of these persons may result from one-handed

operation. A chain saw is intended for two-

handed use.

Guard against electric shock - Avoid body con-

tact with grounded surfaces such as metal pipes

and wire fences. There is an increased risk of

electric shock if your body is grounded.

Do not operate a chain saw that is damaged,

improperly adjusted, or not completely and

securely assembled. Chain should slow to a

stop when the switch trigger is released. If the

chain continues to turn after the switch trigger

has been released, have the unit serviced by an

authorized service center.

Check for damaged parts. Check for alignment

of moving parts, binding of moving parts, break-

age of parts, mounting, and any other condi-

tions that may affect its operation. A guard or

CHAIN SAW SAFETY WARNINGS

6 - English

other part that is damaged should be properly

repaired or replaced by an authorized service

center unless otherwise indicated elsewhere in

this manual.

All chain saw service, other than the items listed

in the operation and maintenance sections,

should be performed by an authorized service

center.

Always maintain a proper stance.

Do not use chain saw if switch does not turn it

on and off. Have defective switch replaced by

an authorized service center.

Do not adapt your powerhead to a bow guide

or use it to power any attachments or devices

not listed for the saw.

Disconnect chain saw from power supply when

not in use, before servicing, and when making

adjustments and changing attachments, such

as saw chain and guard.

Do not cut vines and/or small underbrush.

Do not operate a chain saw in a tree, on a ladder,

rooftop, scaffold, or other unstable support; this

is extremely dangerous.

NOTE: The size of the work area depends on the

job being performed as well as the size tree or

work piece involved. For example, felling a tree

requires a larger work area than making bucking

cuts.

Do not force the chain saw. The job can be per-

formed better and safer at the rate for which it

was intended.

Always use the right product for your applica-

tion. The chain saw should be used for cutting

wood only. Never use the chain saw to cut plas-

tic, masonry or non-wood building materials.

Store chain saw when not in use. Chain saw

should be stored in a dry and high or locked

area out of the reach of children. When storing

chain saw place the scabbard on the bar and

chain and store the chain saw in carrying case.

 Use this product only with batteries and char-

gers listed in tool/appliance/battery pack/char-

ger correlation supplement 988000842.

 Battery operated units do not have to be

plugged into an electrical outlet; therefore, they

are always in operating condition. Be aware

of possible hazards even when unit is not

operating.

 Remove the battery pack from the chain saw

before cleaning, servicing, storing, removing

material from the unit, changing accessories

such as the bar and chain, or when not in use.

Save these instructions. Refer to them fre-

quently and use them to instruct others who

may use this product. If you loan someone this

product, loan them these instructions also.

KICKBACK

See Figures 1 - 3.

WARNING:

Kickback may occur when the moving chain

contacts an object at the upper portion of the

tip of the guide bar or when the wood closes in

and pinches the saw chain in the cut. Contact

at the upper portion of the tip of the guide bar

can cause the chain to dig into the object and

stop the chain for an instant. The result is a

lightning fast, reverse reaction which kicks the

guide bar up and back toward the operator. If

the saw chain is pinched along the top of the

guide bar, the guide bar can be driven rapidly

back toward the operator. Either of these reac-

tions can cause loss of saw control which can

result in serious injury. Do not rely exclusively

upon the safety devices built into the saw. As a

chain saw user, you should take several steps

to keep your cutting jobs free from accident or

injury.

 The following precautions should be followed

to minimize kickback:

• Always grip the saw firmly with both hands.

Hold the saw firmly with both hands when

the unit is running. Place your right hand on

the rear handle and your left hand on the

front handle with your thumbs and fingers

encircling the chain saw handles. A firm grip

together with a stiff left arm will help you

maintain control of the saw if kickback occurs.

• Make sure that the area in which you are cut-

ting is free from obstructions. Do not let the

nose of the guide bar contact a log, branch,

CHAIN SAW SAFETY WARNINGS

7 - English

fence, or any other obstruction that could be

hit while you are operating the saw.

• Always cut with the unit running at full speed.

Fully squeeze the throttle trigger and maintain

a steady cutting speed.

• Use replacement parts such as low kick-

back chain, chain brakes and special guide

bars that reduce the risks associated with

rotational kickback. Use only the replacement

guide bars and low kickback chains specified

by the manufacturer for the saw.

 With a basic understanding of kickback, you

can reduce or eliminate the element of surprise.

Sudden surprise contributes to accidents.

 Do not overreach. Keep proper footing and bal-

ance at all times.

 Do not cut above chest height or overreach

when cutting. Do not let the nose of the guide

bar contact a log, branch, ground, or any other

obstruction while you are operating the unit.

 Follow the sharpening and maintenance

instructions for the saw chain.

 Push and Pull - This reaction force is always

opposite to the direction the chain is moving

where wood contact is made. Thus, the operator

must be ready to control the PULL when cutting

on the bottom edge of the bar, and PUSH when

cutting along the top edge. See Figure 3.

UNDERSTANDING YOUR CHAIN SAW

SAFETY DEVICES

LOW KICKBACK SAW CHAIN

The rakers (depth gauges) ahead of each cutter

can minimize the force of a kickback reaction by

preventing the cutters from digging in too deeply

at the kickback zone. Only use replacement chain

that is equivalent to original chain or has been

certified as low kickback chain per ANSI B175.1.

Low kickback saw chain is chain that has met

the kickback performance requirements of ANSI

B175.1 - 2012 (American National Standard

for Power Tools - Gasoline-Powered Chain

Saws-Safety Requirements) when tested on the

representative sample of chain saws below 3.8

c.i.d. specified in ANSI B175.1 - 2012.

Fig. 1

Fig. 2

Fig. 3

ROTATIONAL

KICKBACK

DANGER ZONE

PULL

PUSH

CHAIN SAW SAFETY WARNINGS

As saw chains are sharpened during their useful

life, they lose some of the low kickback qualities

and extra caution should be used.

GUIDE BARS

Generally, guide bars with small radius tips have

somewhat lower kickback potentials.

When making a replacement, be sure to order

one of the RYOBI bars listed for the saw in this

operator’s manual.

8 - English

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and

understand operator’s manual before using this

product.

Wear Eye, Hearing, and

Head Protection

Wear eye protection with side shields marked to

comply with ANSI Z87.1 as well as hearing and head

protection when operating this equipment.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Operate With Two

Hands

Hold and operate the saw properly with both hands.

One Handed Do not operate the saw using only one hand.

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered

important, but not related to a potential injury (e.g. messages re-

lating to property damage).

9 - English

Some of the following symbols may be used on this product. Please study them and learn their

meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Kickback DANGER! BEWARE OF KICKBACK.

Bar Nose Contact Avoid bar nose contact.

Wear Gloves

Wear non-slip, heavy-duty protective gloves when

handling the chain saw.

Wear Safety Footwear

Wear non-slip safety footwear when using this

equipment.

Keep Tool Away from

Electrical Lines/Keep

Bystanders Away

DANGER! Risk of electrocution! Keep tool 50 feet away

from electrical lines. Keep all bystanders at least 50

ft. away or twice the height of the largest trees in the

felling area when felling.

Oil Indicator

Pour bar and chain lubricant into oil tank where

indicated. Do not use any other fluids.

Recycle Symbol

This product uses lithium-ion batteries. Local, state or

federal laws may prohibit disposal of batteries in ordinary

trash. Consult your local waste authority for information

regarding available recycling and/or disposal options.

V Volts Voltage

Direct Current Type or a characteristic of current

SYMBOLS

10 - English

GLOSSARY OF TERMS

Bucking

The process of cross cutting a felled tree or log

into lengths.

Chain Saw Powerhead

A chain saw without the saw chain and guide bar.

Drive Sprocket or Sprocket

The toothed part that drives the saw chain.

Felling

The process of cutting down a tree.

Felling Back Cut

The final cut in a tree felling operation made on

the opposite side of the tree from the notching

undercut.

Front Hand Guard

A structural barrier between the front handle of a

chain saw and the guide bar, typically located close

to the hand position on the front handle.

Front Handle

The support handle located at or toward the front

of the chain saw. This handle is for the left hand.

Guide Bar

A solid railed structure that supports and guides

the saw chain.

Kickback

The backward or upward motion, or both, of the

guide bar occurring when the saw chain near the

nose of the top area of the guide bar contacts any

object such as a log or branch, or when the wood

closes in and pinches the saw chain in the cut.

Kickback (Pinch)

The rapid pushback of the saw which can occur

when the wood closes in and pinches the moving

saw chain in the cut along the top of the guide bar.

Kickback (Rotational)

The rapid upward and backward motion of the

saw which can occur when the moving saw chain

near the upper portion of the tip of the guide bar

contacts an object, such as a log or branch.

Lock-out button

A movable stop that prevents the unintentional

operation of the switch until manually actuated.

Low-Kickback Chain

A chain that complies with the kickback

performance requirements of ANSI B175.1 when

tested on a representative sample of chain saws.

Normal Cutting Position

Those positions assumed in performing the bucking

and felling cuts.

Notching Undercut

A notch cut in a tree that directs the tree’s fall.

Rear Handle

The support handle located at or toward the rear

of the saw. It normally contains the switch trigger.

This handle is for the right hand.

Reduced Kickback Guide Bar

A guide bar which has been demonstrated to

reduce kickback significantly.

Replacement Saw Chain

A chain that complies with the kickback

performance requirements of ANSI B175.1 when

tested with specific chain saws. It may not meet

the ANSI performance requirements when used

with other saws.

Saw Chain

A loop of chain having cutting teeth that cut the

wood, and that is driven by the motor and is

supported by the guide bar.

Springpole

A small tree (sapling) or limb that is bent or trapped

under tension. It may “spring back” rapidly when

cut, causing a dangerous situation.

Switch Trigger

A device that when operated will complete or

interrupt an electrical power circuit to the motor

of the chain saw.

11 - English

FEATURES

PRODUCT SPECIFICATIONS

Motor ....................................................................................................................................40 Volt DC

Bar Length ....................................................................................................................................14 in.

Chain oil tank capacity .................................................................................................................. 6 oz.

NOTE: This saw was designed for occasional light duty use and has some limitations as to what it

can cut.

Fig. 4

CHAIN OIL

TANK CAP

REAR

HANDLE

FRONT HANDLE

GUIDE

BAR

LOW KICKBACK

CHAIN

TENSIONING

SCREW

BATTERY PACK

FRONT HAND

GUARD

CHAIN

COVER

SWITCH TRIGGER

SCABBARD

BATTERY PACK

LOCK-OUT

BUTTON

QUICK VIEW OIL

INDICATOR

12 - English

FEATURES

KNOW YOUR CHAIN SAW

See Figure 4.

The safe use of this product requires an

understanding of the information on the tool and

in this operator’s manual as well as a knowledge

of the project you are attempting. Before use of

this product, familiarize yourself with all operating

features and safety rules.

CHAIN TENSIONING SCREW

This feature allows user to adjust the tension of

the chain.

GUIDE BAR

The factory-equipped guide bar has a small radius

tip that offers a somewhat lower kickback potential.

LOCK-OUT BUTTON

A control feature designed to prevent the motor

from being accidently started.

LOW KICKBACK CHAIN

The low kickback chain helps minimize the force

of a kickback reaction by preventing the cutters

from digging in too deeply at the kickback zone.

QUICK VIEW OIL INDICATOR

Semi-transparent oil reservoir that allows user to

see when to add oil.

SWITCH TRIGGER

Squeeze the switch trigger to operate the unit after

switch lock-out has been pushed in. Release the

switch trigger to stop the unit.

ASSEMBLY

UNPACKING

This product has been shipped completely

assembled.

 Carefully remove the product and any

accessories from the box. Make sure that all

items listed in the packing list are included.

WARNING:

Do not use this product if any parts on the

Packing List are already assembled to your

product when you unpack it. Parts on this

list are not assembled to the product by the

manufacturer and require customer installation.

Use of a product that may have been improperly

assembled could result in serious personal

injury.

 Inspect the product carefully to make sure no

breakage or damage occurred during shipping.

 Do not discard the packing material until you

have carefully inspected and satisfactorily

operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Chain Saw with Scabbard

Combination Wrench

Operator’s Manual

WARNING:

If any parts are damaged or missing do not

operate this product until the parts are replaced.

Use of this product with damaged or missing

parts could result in serious personal injury.

13 - English

WARNING:

Do not attempt to modify this product or create

accessories not recommended for use with this

product. Any such alteration or modification

is misuse and could result in a hazardous

condition leading to possible serious personal

injury.

DANGER:

Never cut near power lines, electric cords, or

other electric sources. If bar and chain jams

on any electrical cord or line, DO NOT TOUCH

THE BAR OR CHAIN! THEY CAN BECOME

ELECTRICALLY LIVE AND VERY DANGEROUS.

Continue to hold the chain saw by the insulated

rear handle or lay it down and away from you in

a safe manner. Disconnect the electrical service

to the damaged line or cord before attempting

to free the bar and chain from the line or cord.

Contact with the bar, chain, other conductive

parts of the chain saw, or live electric cords or

lines will result in death by electrocution, electric

shock, or serious personal injury.

WARNING:

Do not allow familiarity with this product to

make you careless. Remember that a careless

fraction of a second is sufficient to inflict serious

injury.

WARNING:

Always wear eye protection with side shields

marked to comply with ANSI Z87.1 as well as

head and hearing protection when operating

this equipment. Failure to do so could result in

objects being thrown into your eyes and other

possible serious injuries.

ASSEMBLY

OPERATION

WARNING:

Do not use any attachments or accessories

not recommended by the manufacturer of this

product. The use of attachments or accessories

not recommended can result in serious personal

injury.

WARNING:

Never fell a tree or cut a log or limb that has a

diameter greater that the length of the guide

bar. Only properly trained professionals should

perform these cuts. Performing these types of

cuts can cause an accident and result in death

or serious personal injury.

NOTICE:

Before each use, inspect the entire product

for damaged, missing, or loose parts such as

screws, nuts, bolts, caps, etc. Tighten securely

all fasteners and caps and do not operate this

product until all missing or damaged parts are

replaced. Please contact customer service or a

qualified service center for assistance.

APPLICATIONS

You may use this product for the following purposes:

Limbing and pruning branches from trees

Felling small trees

Bucking the fallen tree into shorter lengths

WARNING:

To prevent accidental starting that could cause

serious personal injury, always remove the

battery pack from the product when assembling

parts.

14 - English

TO INSTALL/REMOVE BATTERY PACK

See Figure 5.

WARNING:

Always remove battery pack from your tool

when you are assembling parts, making

adjustments, cleaning, carrying, transporting

or when not in use. Removing battery pack will

prevent accidental starting that could cause

serious personal injury.

NOTE: To avoid serious personal injury, always

remove the battery pack and keep hands clear of

the lock-out button when carrying or transporting

the tool.

To install:

 Place the battery pack in your chain saw. Align

raised rib on battery pack with groove in chain

saw’s battery port.

 Make sure the latch on bottom side of battery

pack snaps in place and that battery pack is

secured in chain saw before beginning operation.

To remove:

Locate latch on bottom of battery pack and depress

both sides to release the battery pack from the

chain saw.

NOTICE:

When placing battery pack in your chain saw,

be sure raised rib on battery pack aligns with

groove in chain saw’s battery port and latches

snap in place properly. Improper assembly of

battery pack can cause damage to internal

components.

For complete charging instructions, see the opera-

tor’s manuals for your battery pack and charger.

NOTICE:

Remove battery pack from unit. Fill oil tank with

bar and chain lubricant (not provided) before

starting the chain saw. Failure to lubricate the

chain will cause damage to the bar and chain.

CHAIN OIL SYSTEM

See Figure 6.

 Use bar and chain lubricant (not provided).

That is formulated to perform over a wide

temperature range with no dilution required.

OPERATION

NOTE: Do not use dirty, used or otherwise

contaminated oils. Damage may occur to the

bar or chain.

 Carefully pour the bar and chain oil into the tank.

 Check and fill the oil tank when battery is

recharged, or as needed.

NOTE: It is normal for lubricant to seep from the

saw when not in use. To prevent seepage, empty

the oil tank after each use. When storing the unit

for a long period of time (three months or longer) be

sure the chain is lightly lubricated; this will prevent

rust on the chain and bar sprocket.

NOTICE:

Before each use, check to make sure that the

chain is properly tensioned. A cold chain is cor-

rectly tensioned when there is no slack on the

underside of the guide bar, the chain is snug,

and it can be turned by hand without binding.

During normal saw operation, the temperature

of the chain increases. The drive links of a cor-

rectly tensioned warm chain will hang approxi-

mately .050 in. out of the bar groove.

See the Adjusting the Chain Tension instruc-

tions in the Maintenance section of this manual

to properly adjust the chain tension.

Fig. 6

Fig. 5

BATTERY

PACK

LATCH

BATTERY

PORT

15 - English

STARTING AND STOPPING THE CHAIN

SAW

See Figure 7.

WARNING:

Keep body to the left of the chain line. Never

straddle the saw or chain, or lean over past the

chain line.

Starting the chain saw:

 Slide and hold the lock-out button. This makes

the switch trigger operational.

 Press and hold the switch trigger, release the

lock-out button and continue to squeeze the

switch trigger for continued operation.

Stopping the chain saw:

 Release the switch trigger to stop the chain saw.

 Upon release of the switch trigger, the lock-out

button will be automatically reset to the lock

position.

This cordless chain saw is designed for limbing and

pruning type cutting, as well as cutting small trees.

PREPARATION FOR CUTTING

PROPER GRIP ON HANDLES

See Figures 8 - 10.

Refer to General safety rules earlier in this manual

for appropriate safety equipment.

 Wear non-slip gloves for maximum grip and

protection.

 Hold the saw firmly with both hands. Always

keep your left hand on the front handle and your

right hand on the rear handle so that your body

is to the left of the chain line.

WARNING:

Never use a left-handed (cross-handed) grip,

or any stance which would place your body or

arm across the chain line.

 Maintain a proper grip on the saw whenever

the unit is running. The fingers should encircle

the handle and the thumb is wrapped under the

handlebar. This grip is least likely to be broken

(by a kickback or other sudden reaction of the

saw). Any grip in which the thumb and fingers

OPERATION

Fig. 7

LOCK-OUT

BUTTON

SWITCH

TRIGGER

SWITCH

TRIGGER

LOCK-OUT

BUTTON

Fig. 8

16 - English

OPERATION

STRAIGHT ARM

POSITION

CHAIN LINE

are on the same side of the handle, is dangerous

because a slight kick of the saw can cause loss

of control.

WARNING:

Do not operate the switch trigger with your left

hand and hold the front handle with your right

hand. Never allow any part of your body to be

in the chain line while operating a saw. Improper

operation of the chain saw could result in seri-

ous personal injury.

PROPER CUTTING STANCE

See Figures 11 - 12.

WARNING:

Always use the proper cutting stance described

in this section. Never kneel when using the chain

saw, except when felling a tree as illustrated

in Figure 12. Kneeling could result in loss of

stability and control of the chain saw, resulting

in serious personal injury.

 Weight should be balanced with both feet on

solid ground.

 Keep left arm with elbow locked in a “straight

arm” position to withstand any kickback force.

 Your body should always be to the left of the

chain line.

 Thumb should be on underside of handlebar.

BASIC CUTTING PROCEDURE

Practice cutting a few small logs using the following

technique to get the “feel” of using the saw before

you begin a major sawing operation.

 Take the proper stance in front of the wood with

the saw off.

 Squeeze the switch trigger and let the chain

accelerate to full speed before entering the cut.

 Begin cutting with the saw against the log.

 Keep the unit running the entire time you are

cutting, maintain a steady speed.

 Allow the chain to cut for you; exert only light

downward pressure. If you force the cut,

damage to the bar, chain, or unit can result.

Fig. 10

Fig. 9

Fig. 11

Fig. 12

CHAIN LINE

17 - English

 Release the switch trigger as soon as the cut

is completed, allowing the chain to stop. If you

run the saw without a cutting load, unnecessary

wear can occur to the chain, bar, and unit.

 Do not put pressure on the saw at the end of

cut.

WORK AREA PRECAUTIONS

See Figure 13.

 Cut only wood or materials made from wood,

no sheet metal, no plastics, no masonry, no

non-wood building materials.

 Never allow children to operate the saw. Allow

no person to use this chain saw who has

not read this Operator’s Manual or received

adequate instructions for the safe and proper

use of this chain saw.

 Keep everyone - helpers, bystanders, children,

and animals - a safe distance from the cutting

area. During felling operations, the safe dis-

tance should be a least twice the height of the

largest trees in the felling area. During bucking

operations, keep a minimum distance of 15 feet

between workers.

 Always cut with both feet on solid ground to

prevent being pulled off balance.

 Do not cut above chest height, as a saw held

higher is difficult to control against kickback

forces.

 Do not fell trees near electrical wires or buildings.

Leave this operation for professionals.

 Cut only when visibility and light are adequate

for you to see clearly.

FELLING TREES

See Figures 13 - 16.

HAZARDOUS CONDITIONS

WARNING:

Do not fell trees during periods of high wind or

heavy precipitation. Wait until the hazardous

weather has ended.

OPERATION

Fig. 13

HINGE

2 in. OR 1/10 DIA

NOTCH -

APPROX. 1/3

DIAMETER OF

TRUNK

BACK CUT

2 in.

Fig. 14

NOTCH

BACK CUT

Fig. 15

HINGE

45°

PLANNED LINE

OF FALL

RETREAT PATH

18 - English

WARNING:

Closely check for broken or dead branches,

which could fall while cutting and do not cut

near buildings or electrical wires if you do not

know the direction of tree fall. Do not cut at

night or during bad weather conditions, such as

rain, snow, or strong winds, which can reduce

visibility and control of the chain saw. If the tree

you are felling makes contact with any utility

line, you should discontinue use of the chain

saw and immediately notify the utility company.

Failure to follow these instructions could result

in death or serious personal injury.

When felling a tree, it is very important that you

closely follow these warnings and instructions to

prevent possible death or serious personal injury.

■Do not cut down trees having an extreme lean

or large trees with rotten limbs, loose bark,

or hollow trunks. Have these trees pushed or

dragged down with heavy equipment, then cut

them up.

■Do not cut trees near electrical wires or

buildings.

■Check the tree for damaged or dead branches

that could fall and hit you during felling.

■Periodically glance at the top of the tree during

the backcut to assure the tree is going to fall in

the desired direction.

If the tree starts to fall in the wrong direction,

or if the saw gets caught or hung up during the

fall, leave the saw and save yourself!



Felling a tree — When bucking and felling

operations are being performed by two or more

persons, at the same time, the felling operation

should be separated from the bucking operation

by a distance of at least twice the height of the

tree being felled. Trees should not be felled in a

manner that would endanger any person, strike

any utility line or cause any property damage. If

the tree does make contact with any utility line, the

utility company should be notified immediately.

 Before any cuts are started, pick your escape

route (or routes in case the intended route is

blocked); clear the immediate area around the

tree and make sure there are no obstructions in

your planned path of retreat. Clear paths of safe

retreat should extend back and diagonally (45°)

to the rear of the planned line of fall. When the

tree begins to fall, you should retreat away from

the direction of fall along a retreat path and at

least 20 feet away from the trunk in case it kicks

back over the stump. See Figure 13.

 Before felling is started, consider the force and

direction of the wind, the lean and balance of

the tree, and the location of large limbs. These

things influence the direction in which the tree

will fall. Do not try to fell a tree along a line

different from its natural line of fall.

 The chain saw operator should keep on the

uphill side of the terrain as the tree is likely to

roll or slide downhill after it is felled.

OPERATION

Fig. 16

WEDGE

KICKBACK

Fig. 17

Fig. 18

19 - English

 Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where felling cuts are to

be made.

 Notched Undercut. Cut a notch about 1/3

the diameter of the tree, perpendicular to the

direction of fall. Make the cuts of the notch so

they intersect at a right angle to the line of fall.

This notch should be cleaned out to leave a

straight line. To keep the weight of the wood

off the saw, always make the lower cut of the

notch before the upper cut. See Figure 14.

 Felling Backcut. The backcut is always made

level and horizontal, and at a minimum of 2

in. above the horizontal cut of the notch. See

Figures 14 - 15.

 Never cut through to the notch. Always leave a

band of wood between the notch and backcut

(approximately 2 in. or 1/10 the diameter of the

tree). This is called “hinge” or “hingewood.” It

controls the fall of the tree and prevents slipping

or twisting or shoot-back of the tree off the

stump. See Figures 14 - 15.

 On large diameter trees, stop the back cut

before it is deep enough for the tree to either

fall or settle back on the stump. Then insert

soft wooden or plastic wedges into the cut so

they do not touch the chain. The wedges can

be driven in, little by little, to help jack the tree

over. See Figure 16.



As tree starts to fall, stop the chain saw and put

it down immediately. Retreat along the cleared

path, but watch the action in case something

falls your way. Be alert for overhead limbs or

branches that may fall and watch your footing.

WARNING:

Never cut through to the notch when making a

backcut. The hinge controls the fall of the tree,

this is the section of wood between the notch

and backcut.

BUCKING

See Figures 17 - 20.

Bucking is the term used for cutting a fallen tree

to the desired log length.

 Always make sure your footing is secure and

your weight is distributed evenly on both feet.

■ Cut only one log at a time.

OPERATION

■ Support small logs on a saw horse or another

log while bucking.

■ Keep a clear cutting area. Make sure that no

objects can contact the guide bar nose and

chain during cutting, this can cause kickback.

 When bucking on a slope, always stand on

the uphill side of the log. To maintain complete

control of the chain saw when cutting through

the log, release the cutting pressure near the

end of the cut without relaxing your grip on the

chain saw handles. Do not let the chain contact

the ground. After completing the cut, wait for the

saw chain to stop before you move the chain

saw. Always stop the motor before moving from

tree to tree.

■ Sometimes it is impossible to avoid pinching

(with just standard cutting techniques) or difficult

to predict which way a log will settle when cut.

To avoid pinching while cutting, rotate or move

the log so that the pinch is eliminated.

BUCKING LOGS UNDER STRESS

See Figures 19 - 20.

When the log is supported along its entire length,

it should be cut from the top or overbucking.

When the log is supported on one end, cut 1/3

the diameter from the underside or underbucking.

LOAD

1ST CUT

1/3 DIA

LOG SUPPORTED AT ONE END:

LOG SUPPORTED AT BOTH ENDS:

FINISHING CUT

LOAD

1ST CUT 1/3 DIA

Fig. 19

FINISHING CUT

20 - English

OPERATION

Then make the finishing cut by overbucking to

meet the first cut.

As the log is being cut, it will tend to bend. The

saw can become pinched or hung in the log if you

make the first cut deeper than 1/3 of the diameter

of the log.

Give special attention to logs under stress to

prevent the bar and chain from pinching.

When bucking on a slope, always stand on the

uphill side of the log as shown in figure 18. When

“cutting through,” to maintain complete control

of the chain saw, release the cutting pressure near

the end of the cut without relaxing your grip on the

chain saw handles. Do not let the chain contact

the ground. After completing the cut, wait for the

saw chain to stop before you move the chain saw.

Always stop the motor before moving from tree

to tree.

TYPES OF CUTTING USED

See Figure 20.

OVERBUCKING

Begin on the top side of the log with the bottom

of the saw against the log; exert light pressure

downward. Note that the saw will tend to pull

away from you.

UNDERBUCKING

Begin on the under side of the log with the top

of the saw against the log; exert light pressure

upward. During underbucking, the saw will tend

to push back at you. Be prepared for this reaction

and hold the saw firmly to maintain control.

LIMBING

See Figure 21.

WARNING:

Never climb into a tree to limb or prune. Do

not stand on ladders, platforms, a log, or in

any position which can cause you to lose your

balance or control of the saw, which could result

in death or other serious personal injury.

Limbing is removing branches from a fallen tree.

 Work slowly, keeping both hands on the chain

saw with a firm grip. Always make sure your

footing is secure and your weight is distributed

evenly on both feet.

 Leave the larger support limbs under the tree to

keep the tree off the ground while cutting.

 Limbs should be cut one at a time. Remove the

cut limbs from the work area often to help keep

the work area clean and safe.

 Branches under tension should be cut from the

bottom up to avoid binding the chain saw.

 Keep the tree between you and the chain saw

while limbing. Cut from the side of the tree

opposite the branch you are cutting.

Fig. 20

CUT LIMBS ONE AT A TIME AND LEAVE SUPPORT LIMBS

UNDER TREE UNTIL LOG IS CUT

Fig. 21

4

1

3

2

OVERBUCKING

UNDERBUCKING

La page charge ...

Ryobi RY40511 Le manuel du propriétaire

Ce manuel convient également à

Ryobi RY40511 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents