Clifford 4816X Le manuel du propriétaire

OWNER’S GUIDE

MODEL

The company behind Viper

®

Auto Security

Systems is Directed.

Since its inception, Directed has had one

purpose, to provide consumers with the fin-

est vehicle security and accessories avail-

able. The recipient of nearly 100 patents and

Innovations Awards in the field of advanced

electronic technology.

Quality Directed products are sold and ser-

viced throughout North America and around

the world.

Call (800) 876-0800 for more information

about our products and ser vic es.

Directed is committed to delivering

world class quality products and

services that excite and delight our

customers.

®

NO ONE DARES

COME CLOSE

®

Vista, CA 92081

www.viper.com

4811V

4816V

©

i

Congratulations

Congratulations on the purchase of your remote start system. This sys-

tem has been designed to provide years of trouble-free operation. By

carefully reading this owner’s guide prior to using your system, you will

maximize the use of this system and its features.

For more information please visit us online (see back cover for URL).

For any additional questions please contact your authorized Directed

dealer or contact Directed at 1-800- 753- 0600 (U.S. only) or 1-800-

361-7271 (Canada only). Additional support is also available at:

http://support.directed.com

What you get

• One 2- way, 1- button remote control

• One 1- way, 1- button remote control

• Owners Guide

Replacement Remote controls

Please see your authorized dealer or visit us at www.directedstore.com

to order additional remote controls. Remote control part numbers are

found on the back of the device.

ii

Important Information

Government Regulations and Safety Information

Read the "Government Regulations" and "Warning!

Safety First" sections of this manual prior to operating this

system.

Warning! Failure to heed this information can result in

death, personal injury or property damage and may also

result in the illegal use of the system beyond its intended

purpose.

This product is designed for fuel-injected, automatic trans-

mission vehicles only. Installing it in a standard transmis-

sion vehicle is dangerous and is contrary to its intended

use. If your vehicle is equipped with a manual transmis-

sion cease use of this product and immediately return the

vehicle to an authorized Directed dealer.

Your warranty

Your system comes with a warranty. The warranty terms are detailed at

the end of this guide. Make sure that you receive the proof of purchase

from your dealer, indicating the product was installed by an authorized

Directed dealer.

Contents

Congratulations ................................................................................................i

What you get ....................................................................................................i

Replacement Remote controls ......................................................................i

Important Information ........................................................................................ii

Government Regulations and Safety Information .......................................... ii

Your warranty...........................................................................................ii

Using Your System ...........................................................................................2

Commands At a Glance ............................................................................2

Start Engine .............................................................................................2

Unlock Doors ...........................................................................................2

Stop Engine .............................................................................................2

Car Finder ...............................................................................................3

Using Remote Start ............................................................................................3

Key Takeover............................................................................................4

Safety Features .........................................................................................4

Pit Stop and Turbo Timer Modes .................................................................5

Manual Transmission Vehicles ....................................................................6

Low Runtime and Remote Start Shutdown Alerts ...........................................7

Optional Rear Defogger ............................................................................7

Starter Anti-Grind Circuitry .........................................................................7

Disabling the Remote Start System ..............................................................7

Remote Start Faults .................................................................................... 8

Rapid Resume Logic .........................................................................................8

Remote Pairing .................................................................................................9

Programming Options ......................................................................................10

Battery Information ..........................................................................................11

Battery Disposal .....................................................................................12

Glossary of Terms............................................................................................12

Government Regulations ..................................................................................14

Warning! Safety First .......................................................................................15

Installation .............................................................................................15

Remote Start Capable .............................................................................15

Manual Transmission Vehicles ..................................................................15

Interference ............................................................................................17

Upgrades ..............................................................................................17

Water/Heat Resistance ...........................................................................17

Limited lifetime consumer warranty ....................................................................18

2

Using Your System

Commands At a Glance

System State

Press/Release

Press/Hold for 3 sec.

ENGINE OFF START ENGINE CAR FINDER

ENGINE ON UNLOCK DOORS STOP ENGINE

Note: If a feature cannot be activated when performing a command

with the 2-way remote control or if the system is out of range, a fault

tone plays as an alert.

Start Engine

When the engine is OFF, press and release the remote control button

to start the engine.

See "Using Remote Start" on page 3 for more feature details.

Unlock Doors

When the engine is ON with remote start, press and release the re-

mote control button. The doors unlock, the parking lights ﬂash, the horn

sounds (if connected) as conﬁrmation. The 2-way remote control emits

tones.

Note: Horn honk may be an optional feature that requires additional

parts and labor.

Stop Engine

When the engine is ON with remote start, press and hold the remote

control button for three seconds. The engine stops running and the park-

ing lights turn off. The 2-way remote control emits tones.

3

Car Finder

When the engine is OFF, press and hold the remote control button for

three seconds. The horn sounds once (if connected) and the parking

lights ﬂash multiple times. The 2-way remote control emits a single tone.

Using Remote Start

This feature allows you to remotely start and run your vehicle for a

programmable period of time. This makes it possible to warm up the

engine, and adjust the interior temperature of the vehicle with the cli-

mate control system. If interior heating or cooling is desired, the climate

controls must be preset, and the fan blower must be set to the desired

level prior to remote starting the vehicle.

Important! (1) Never remotely start the vehicle with the

vehicle in gear, and (2) Never remotely start the vehicle

with the key in the ignition.

Starting the Engine:

1. Make sure the parking brake is set. Press and release the remote

control button once* (or the amount of times the system has been

programmed to activate the remote start).

2. The engine will START and the parking lights will turn on. The

2-way remote will also emit tones.

The parking lights stay on as visual conﬁrmation while the engine is

ON. The default runtime is 12 minutes and can be shortened or ex-

tended by the installer. If a remote start conﬁguration issue prevents the

engine from starting, the parking lights ﬂash a remote start fault report

to identify the fault. See "Remote Start Faults" on page 8.

4

* The factory setting is one press but this can also be programmed for

two presses (See your authorized Directed installer for the amount of

presses programmed).

Record the number of presses to activate remote start here:______

Key Takeover

When you are ready to drive the vehicle:

1. Unlock the doors.

2. Enter the vehicle. Do not step on the foot brake.

3. Insert the key into the ignition and turn it to the run (not start) posi-

tion.

4. Step on the foot brake. The remote start is disabled and the park-

ing lights turn off.

5. Disengage the parking brake and begin driving.

Note

If your vehicle uses a Smart Key or PTS (Push-To-Start) system,

please refer to the vehicle speciﬁc instructions included with

the owner's guide of the interface module or consult your

authorized dealer.

Safety Features

The following safety features will disable the remote start when acti-

vated or not allow the engine to start if not properly set before starting.

• Foot Brake is depressed

• Hood is open

• Remote Start shutoff switch is OFF

• The pre-programmed run time (12, 24 or 60 minutes) has elapsed

• Remote Start activation procedure is repeated

• Parking brake is disengaged

5

• Engine over-rev protection (Tachometer mode only)

Pit Stop and Turbo Timer Modes

This remote start can keep the engine running during short trips away

from the vehicle or to cool down turbo timers.

Enabling Pit Stop mode:

1. Park in a well ventilated area.

2. With the engine running engage the parking brake and release

the foot brake.

3. Press and release the remote control button once (or the amount

of times the system has been programmed to activate the remote

start). The parking lights turn on as conﬁrmation.

4. Turn off the ignition and remove the key, the engine continues

running.

5. Exit the vehicle, the engine runs for the programmed runtime.

Enabling Turbo Timer mode *:

Begin by following the "Enabling Pit Stop mode" procedure. However,

in step 3, instead of pressing the remote control button, press and re-

lease the dash mounted activation button* once (or the amount of times

the system has been programmed to activate the remote start). The

engine continues running for the shorter Turbo Mode runtime. Continue

and complete the procedure steps.

* Turbo Timer mode must be turned on and an optional activation but-

ton also installed by an authorized dealer.

Note: For Manual Transmission vehicles see "Manual Transmission Ve-

hicles" on page 6.

6

Note

If your vehicle uses a Smart Key or PTS (Push-To-Start) system,

please refer to the vehicle speciﬁc instructions included with

the owner's guide of the interface module or consult your

authorized dealer.

Manual Transmission Vehicles

Manual Transmission Mode (MTS), Pit Stop mode, Turbo Timer Mode

Enabling MTS mode

1. Park in a well ventilated area with all the doors closed.

2. With the engine running, press the foot brake and set the parking

brake.

3. Release the foot brake.

4. Press and release the remote control button, the parking lights ﬂash

quickly ﬁve times as conﬁrmation.

5. Turn off the ignition and remove the key, the engine continues

running.

6. Exit the vehicle.

7. When the doors are closed, the engine stops running, MTS mode

is enabled.

Note: If enabling MTS mode has failed, the parking lights ﬂash slowly

ﬁve times, return to step 1 and repeat procedure.

Enabling Pit Stop mode:

Follow the previous Enabling MTS mode procedure, however, open a

door prior to step 4. The engine continues running for the programmed

runtime after the doors are closed.

Enabling Turbo Timer mode*:

Follow the previous Enabling MTS mode procedure, however, open a

7

door prior to Step 4. Then, instead of pressing the remote control but-

ton, press and release the optional dash mounted activation button*.

The engine continues running for the shorter Turbo Mode runtime after

the doors are closed.

* Turbo Timer mode must be turned on and an optional activation but-

ton also installed by an authorized dealer.

Low Runtime and Remote Start Shutdown Alerts

During remote start, the system sill send a low runtime alert to the 2-way

remote when the remote start reaches the three minute and one minute

runtime remaining point. When the remote start shuts down, the 2-way

remote will also play a descending tone to indicate that the remote

start has shutoff.

Optional Rear Defogger

If connected, the Defogger circuit automatically activates ten seconds

after remote starting the vehicle if the temperature is below 55°F

(12.8°C).

Starter Anti-Grind Circuitry

This system includes an anti-grind circuit (optional relay is required) that

can prevent damage to the starter motor if the key is turned to the start

position while the engine is ON.

Note: Anti-grind circuitry only works when the remote start system is

op er at ing the motor and the optional relay is installed.

Disabling the Remote Start System

When the Remote Start shutoff switch is set to the OFF position, remote

engine starting is defeated. DO this when the vehicle is being serviced

8

or driven by someone unfamiliar with remote start system operations.

Location Of Remote Start shutoff switch: _______________________

Remote Start Faults

For user safety, the system must be properly conﬁgured or remote start

will not activate. A Remote Start Fault may be caused by any of several

conﬁguration issues. Refer to the table below for the command type

and parking light ﬂashes that will identify the conﬁguration issue and

solution.

Flashes * Possible Fault Solution

5 Brake on Release foot brake

6 Hood open Close hood

7 After performing Remote Start

command - MTS not enabled

Enable MTS mode

8 Toggle Switch off Turn switch on

Rapid Resume Logic

This Directed system stores its current state to non-volatile memory. If

power is lost and then reconnected the system recalls the stored state

from memory. This means if the unit is in Locked Mode and the battery

is dis con nect ed for any reason, such as when servicing the vehicle,

when the battery is re con nect ed the unit maintains Locked Mode. This

applies to all states of the system.

9

Remote Pairing

Your system comes with two remote controls that are already paired to

the system. An additional two remote controls can be stored in the sys-

tem's memory (for a maximum of four). However, additional or replace-

ment remote controls need to paired to the system ﬁrst before use. Use

the following procedure to pair an additional or replacement remote

control to the system.

To pair a new remote control to the system:

1. Turn the ignition to the ON position.

2. Within ten seconds, press/release once and then press and hold

the control button on the system’s control center. The status LED be-

gins ﬂashing in a sequence of single ﬂashes and the horn sounds

(if connected) to conﬁrm the system is ready for pairing. Release

the control center button.

3. Press and release the button on the remote control twice and then,

press and hold on the third press. The transmit LED comes on solid,

continue holding the button until the transmit LED changes its pat-

tern. Release the button and the transmit LED begins ﬂashing as an

indication that the remote control has entered pairing mode.

4. Press and release the button on the remote control.

5. The horn (if connected) sounds as a conﬁrmation the system has

paired with the remote control and the 2-way remote control plays

tones conﬁrming that it has paired with the system and will auto-

matically exit pairing mode. The 1-way remote does not emit any

conﬁrmation tones. The remote will exit programming after 30 sec-

onds or to manually exit programming, press and hold the button

on the remote. The remote emits a tone conﬁrming exit.

6. Turn the ignition off or wait 60 seconds for the system to exit the

pairing mode, the horn will sound as conﬁrmation.

10

The learn routine Exits if any of the following occurs:

• The ignition is turned off.

• There is no activity for 60 seconds.

• The control button is pressed too many times.

Programming Options

Programming options control your system's normal operational set-up.

Most options do not require additional parts, but some may require

installation labor.

The following is a list of the programmable options, with the factory

settings in bold.

• 12, 24, or 60 minute run time. Your system can be programmed

to allow the vehicle to run for 12, 24, or 60 minutes when remote

started. Can be set up to minute increments by your installer.

• Parking lights ﬂashing or constant. Your system can be pro-

grammed to ﬂash or turn on the parking lights constantly during the

entire remote start operation.

• Ignition switch controlled door locking on or OFF. With this feature

on, the doors will lock three seconds after the ignition key is turned

on, and unlock when the key is turned off.

Important: The door lock option must be installed for this feature

to work.

11

Battery Information

The 1-way remote controls are powered by a single coin cell battery

(CR-2016), and the 2-way remote controls are powered by two coin

cell batteries (CR-2016) that can be purchased at most retailers. Oper-

ating range diminishes as battery charge depletes.

Low Battery Alert

When unlocking the vehicle using a remote control with a low battery

charge, the system provides a notiﬁcation by emitting a third horn honk

output (if connected). If conﬁrmation chirps are programmed off, the

system still emits one horn honk when unlocking. After performing a

command with the remote control, several beeps play to indicate the

battery/batteries need replacing. Once the alerts begin, the remote

control will remain operational for several days but the battery/batter-

ies should be replaced at the earliest opportunity or failure to control

the system may occur.

Battery Replacement

1. Unscrew the hardware on unit rear and remove from housing.

2. Use a small ﬂat blade screwdriver and insert it into the slot located

along the bottom of the remote, near the key ring. Carefully pry

open the case.

3. Gently slide out the used battery/batteries to remove it from the

holding clip. Orient the new battery for the correct polarity and

insert into holding clip.

4. Realign the case parts and snap together by pressing ﬁrmly and

evenly on the front and back. Reinstall screw.

12

Battery Disposal

Directed cares about the environment. If you need to dispose

of the battery, please do so in accordance with your munici-

pal requirements for battery disposal.

Glossary of Terms

Document Terminology

Control Module

The “brain” of your system. Usually hidden underneath the dash

area of the vehicle. It houses the microprocessor which monitors

your vehicle and controls all of the system’s functions.

Remote Control

A hand-held, remote control which operates the various func-

tions of your system.

Status LED

Transmit LED (Light Emitting Diode): A light used to indicate the

status of your system. It turns on when a button is pressed or

communication is active.

Control Center

Mounted high in the vehicle usually on the windshield in a

location close to the rear view mirror. Consists of a antenna/

receiver for communicating between the control module and

remote controls and a control button with status LED for pro-

gramming system features.

Remote Start shutoff

switch

Normally located near the control module or mounted around

the dashboard, this Remote Start shutoff switch is used to dis-

able the remote start feature.

13

Patent Information

This product is covered by one or more of the following United States

patents:

Vehicle Security Patents

5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591;

5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667;

5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484

Remote Start

5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936;

5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053;

7,483,783

Other patents pending

14

Government Regulations

This device complies with Part 15 of FCC rules. Operation is subject to the fol-

lowing two conditions: (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency ener-

gy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television, which can

be determined by turning the equipment OFF and ON, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for

help.

This device complies with the Industry Canada Radio Standards Speciﬁcation

RSS 210. Its use is authorized only on a no-interference, no-protection basis; in

other words, this device must not be used if it is determined that it causes harm-

ful interference to services authorized by IC. In addition, the user of this device

must accept any radio interference that may be received, even if this interference

could affect the operation of the device.

Warning: Changes or modiﬁcations not expressly approved by the party re-

sponsible for compliance could void the user’s authority to operate this device.

15

Warning! Safety First

Please read the safety warnings below before proceeding. Improper use

of the product may be dangerous or illegal.

Installation

Due to the complexity of this system, installation of this product must only be

performed by an authorized Directed dealer. If you have any questions, ask your

retailer or contact Directed directly at 1-800-753-0600.

Remote Start Capable

When properly installed, this system can start the vehicle via a command signal

from the remote control transmitter. Therefore, never operate the system in an

enclosed area or partially enclosed area without ventilation (such as a garage).

When parking in an enclosed or partially enclosed area or when having the

vehicle serviced, the remote start system must be disabled using the installed

menu wheel. It is the user’s sole responsibility to properly handle and keep out of

reach from children all remote control transmitters to assure that the system does

not unintentionally remote start the vehicle. THE USER MUST INSTALL A CAR-

BON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT

TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO

THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST

AT ALL TIMES REMAIN CLOSED. These precautions are the sole responsibility

of the user.

Manual Transmission Vehicles

Remote starters on manual transmission vehicles operate differently than those

with automatic transmission because you must leave your car in neutral. You

must read this Owner’s Guide to familiarize yourself with the proper procedures

regarding manual transmission remote starters. If you have any questions, ask

your authorized Directed dealer or contact Directed at 1-800-753-0600.

16

Before remote starting a manual transmission vehicle, be sure to:

• Leave the vehicle in neutral and be sure no one is standing in front or

behind the vehicle.

• Only remote start on a ﬂat surface

• Have the parking brake fully engaged

WARNING! It is the responsibility of the owner to ensure the parking/emer-

gency brake properly functions. Failure to do so can result in personal injury or

property damage. We recommend the owner have the parking / emergency

brake system inspected and adjusted by a qualiﬁed automotive shop biannually.

Use of this product in a manner contrary to its intended mode of operation may

result in property damage, personal injury, or death. (1) Never remotely start the

vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with

the keys in the ignition. The user must also have the neutral safety feature of the

vehicle periodically checked, wherein the vehicle must not remotely start while

the car is in gear. This testing should be performed by an authorized Directed

dealer in accordance with the Safety Check outlined in the product installation

guide. If the vehicle starts in gear, cease remote start operation immediately and

consult with the authorized Directed dealer to ﬁx the problem.

After the remote start module has been installed, contact your authorized dealer

to have him or her test the remote start module by performing the Safety Check

outlined in the product installation guide. If the vehicle starts when performing

the Neutral Safety Shutdown Circuit test, the remote start unit has not been

properly installed. The remote start module must be removed or the installer must

properly reinstall the remote start system so that the vehicle does not start in gear.

All installations must be performed by an authorized Directed dealer.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN

GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERAT-

17

ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT

IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY

CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AU-

THORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED

REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR

PAY FOR INSTALLATION OR REINSTALLATION COSTS.

This product is designed for fuel injected vehicles only. Use of this

product in a standard transmission vehicle must be in strict accordance

with this guide.

This product should not be installed in any convertible vehicles, soft or

hard top with a manual transmission. Installation in such vehicles may

pose certain risk.

Interference

All radio devices are subject to interference which could affect proper

performance.

Upgrades

Any upgrades to this product must be performed by an authorized

Directed dealer. Do not attempt to perform any unauthorized modiﬁca-

tions to this product.

Water/Heat Resistance

This product is not designed to be water and/or heat-resistant. Please

take care to keep this product dry and away from heat sources. Any

damage from water or heat will void the warranty.

La page charge ...

Clifford 4816X Le manuel du propriétaire

Clifford 4816X Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents