Haier HDY6-1C Manuel utilisateur

Front Load Electric Dryer

Secheuse Electrique a Chargement Frontal

Secadora eléctrica con carga frontal

User Manual

Model # HDY6-1 / HDY6-1C

Guide de l’Utilisateur

Modéle # HDY6-1 / HDY6-1C

Manual del Usuario

Para Modelo de # HDY6-1 / HDY6-1C

Quality

ß

Innovation

ß

Style

IMPORTANT SAFETY

INSTRUCTIONS

Warning – To reduce the risk of fire, electric shock, or injury to

persons when using your appliance, follow basic precautions,

including the following:

1. Read all instructions before using the appliance.

2. Do not dry articles that have been previously cleaned in, washed in,

soaked in, or spotted with gasoline, dry-cleaning solvents, or other

flammable or explosive substances, as they give off vapors that

could ignite or explode.

3. Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is used

near children.

4. Before the appliance is removed from service or discarded, remove

the door to the drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to water

and/or to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any

servicing unless specifically recommended in the user-maintenance

instructions or in published user-repair instructions that you

understand and have skills to carry out.

9. Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturer of the fabric softener or product.

10. Do not use heat to dry articles containing foam rubber or similarly

textured rubber-like materials.

11. Clean lint screen before or after each load.

12. Keep area around the exhaust opening and adjacent surrounding

areas free from the accumulation of lint, dust and dirt.

13. The interior of the appliance and the exhaust duct should be cleaned

periodically by qualified service personnel.

14. Do not place items exposed to cooking oils in your dryer. Items

contaminated with cooking oils may contribute to a chemical

reaction that could cause a load to catch fire.

21

EnglishEnglish

15. If material has been used with any flammable liquids or solids it

should not be used in the dryer until all traces of the flammable

liquids and its fumes have been removed.

16. This dryer must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions

in the installation section.

17. Proper grounding must be ensured to reduce the risk of electric shock

and fire. Check with a qualified electrician or service personnel if you

are in doubt as to whether the dryer is properly grounded.

18. Use the dryer only for its intended purpose, drying clothes.

19. Always disconnect dryer from electrical supply before attempting any

service. Disconnect power cord by grasping the plug, not the cord.

20. Replace worn power cords and/or loose plugs.

21. To reduce the risk of electric shock or fire, do not use extension cords

or adapters to connect dryer to electrical power source.

SAVE THESE INSTRUCTIONS

For Future Use

21

EnglishEnglish

3

As dry cleaning solvents, gasoline, vegetable and cooking oils are highly

hazardous materials, items soaked in or spotted with such should not

be used in the dryer. Items may still contain a substantial amount of the

hazardous material after being washed. When such items are exposed

to heat they could ignite. As clothes are stacked and piled up in the dryer

the heat cannot escape. Due to this, items become hot enough to possibly

ignite. Washing in hot water with extra detergent would reduce but not

eliminate the risk of fire.

WARNING

Thank you for using our Haier

product. This easy-to-use manual

will guide you in getting the best

use of your dryer.

Remember to record the model and

serial number. They are on a label

in back of the dryer.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

DANGER

Risk of child entrapment. Before you throw away your old

dryer, take off the door so that children may

not easily get trapped inside.

EnglishEnglish

4

TABLE OF CONTENTS

EnglishEnglish

PAGE

SAFETY INSTRUCTIONS ..................................................................1

PARTS AND FEATURES ....................................................................5

INSTALLATION INSTRUCTIONS .......................................................6

Unpacking Your Dryer ..........................................................................6

Tools and Materials Required ................................................................6

Door Reversal ......................................................................................8

Location of Your Dryer ..........................................................................9

Installation in Mobile Home.................................................................10

EXHAUST SYSTEM CONNECTION ...........................................11-16

Electrical Requirement .........................................................................11

3 Wire Cord Connection ....................................................................15

4 Wire Cord Connection ............................................................... 16-17

ELECTRICAL REQUIREMENT FOR CANADA .............................18-19

GROUNDING INSTRUCTIONS ...................................................... 19

PREPARATION .............................................................................. 20

Drying Tips ........................................................................................21

OPERATING INSTRUCTIONS ........................................................ 22

Control Panel ............................................................................... 22-23

Programming Guide ...........................................................................24

OPERATIONAL STEPS ................................................................... 25

NORMAL OPERATING SOUNDS .................................................. 26

ENERGY SAVINGS TIPS ................................................................ 26

CLEANING AND MAINTENANCE ................................................. 27

TROUBLE SHOOTING ...............................................................28-29

SPECIFICATIONS ........................................................................... 29

LIMITED WARRANTY .................................................................... 30

5

PARTS AND FEATURES

1. Control Panel

a. Wrinkle Saver

b. Low Temp

c. Start / Pause

2. Door

3. Program Selector

4. Front Service Cover

5. Grounding Terminal Connection

6. Power Supply Cable

(Canadian version only)

7. Back Plate

8. Back Cover Board

9. Vent Connection

10. Leveling Legs (not shown)

1

2

3

4

5

6

7

8

9

10

Drying

Air Dry / Cool Down

Low Temp

Wrinkle Saver

HDY6-1

Start / Pause

Program

a b c

EnglishEnglish

6

• Select a suitable location for the dryer on a hard, even surface away from

direct sunlight or heat source, e.g. radiators, baseboard heaters, cooking

appliances, etc. Any floor unevenness should be corrected with the leveling

legs located on the bottom of the dryer.

Unpacking Your Dryer

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the dryer accessories inside and outside.

2. Inspect and remove any remains of packaging, tape or printed materials

before using the dryer.

Tools and Materials Required

• Phillips head and flathead screwdrivers

• Channel-lock adjustable pliers

• 1/2 inch open end wrench

• Carpenter’s level

• Measuring tape (12ft. min.)

• Duct tape

• Rigid or flexible metal 4 inch (10.2 cm) duct

• Vent hood

• To ensure that the dryer is operating efficiently, attention must be paid to the

following:

• The dryer must be horizontally installed. Its bottom is equipped

with adjustable legs. Adjust these 4 legs to level before operation.

• Check whether there is any damage to the dryer during transportation. Any

damaged dryer must not be installed.

• The dryer must be kept away from flammable or detonable substances.

• The surrounding environment must be dry and ventilated.

• Do not install the dryer on any carpet.

• To allow the dryer to perform better, the ambient temperature should not be

lower than 50˚C or higher than 95˚F.

INSTALLATION INSTRUCTIONS

EnglishEnglish

7

EnglishEnglish

Packaging Accessories

Checklist of the accessories and materials provided with the machine:

Connect Exhaust Pipe

It is recommended to extract the air outdoors if there is a venting hole where the

dryer is installed. Please use the attached extension hose, connecting sleeve and

hose clip. Before connecting the machine to the power supply, please connect

the small-diameter end of the connecting sleeve to the air exit, and large diam-

eter end of the sleeve to the air exit, and large diameter end of the sleeve to the

extension hose, and tighten it up with a flat screwdriver. Stretch the extension

hose to join it with the venting hole (if no venting hole is available, just stretch the

extension hose out through the window). Keep the hose level and straight.

Put into the venting hole

(or out through the window)

Name Owner's

Manual

Certificate

of

Conformity

Hose

Clip

Extension

Hose

Connecting

Sleeve

Quantity 1 1 1 1 1

8

EnglishEnglish

Door Reversal

• To reverse the door opening of your dryer, follow the below procedures.

a. Using a Phillips head screwdriver, remove the 4 screws that fix the door

hinge to the cabinet. This will un-attach the door from the cabinet.

b. Now unscrew the 4 screws that attach the door hinge to the door.

c. Remove the 2 hinge covers from the opposite side of the door and in its

place attach the just-removed door hinges.

d. Replace the hinge covers to the open slots of the original door hinge

position on the door.

e. Unscrew the 2 screws that attach the door latch to the door, and fix it on

the opposite side after removing the door latch cover.

f. Replace the door latch cover on the door in the place of the just-removed

latch.

g. Using a putty knife, remove the 4 hinge screw covers.

h. Install these on the opposite side.

i. Install the door lock cover on the cabinet on the opposite side.

j. Screw the 4 screws attaching the 2 door hinges to the cabinet.

Door Hinge Cover

Door Lock

Door Hinge

Door

Door Latch

Door Latch Cover

9

Do Not Install Your Dryer:

• In an area exposed to dripping water or outside weather conditions.

• In an area where it will come in contact with curtains, drapes, or anything that

will obstruct the flow of combustion and ventilation air.

• On carpet. Floor must be solid with a maximum slope of 1inch (2.54 cm).

Installation in Recess or Closet:

• A dryer installed in a bedroom, bathroom, recess or closet must be

exhausted outdoors.

• Your dryer needs space around it for proper ventilation.

• A minimum of 120 square inches (774.2 square cm) of opening,

equally divided at the top and bottom of the door, is required. Air

openings are required to be unobstructed when a door is installed.

A louvered door with equivalent air openings for the full length of the door

is acceptable.

Location of Your Dryer

36 3/4”

(93.3 cm.)

DOOR OPEN 90˚

24 3/8”

(61.9 cm.)

33 1/2”

(86 cm)

23 7/16”

(59.4 cm)

ROUGH-IN DIMENSIONS

EnglishEnglish

10

EnglishEnglish

• Dryer must be exhausted outside (outdoors, not beneath the mobile home) using

metal ducting that will not support combustion. Metal ducting must be 4 inches

(10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred.

• If dryer is exhausted through the floor and area beneath the mobile home is

enclosed, the exhaust system must terminate outside the enclosure with the

termination securely fastened to the mobile home structure.

• Refer to previous pages for other important venting requirements.

• Installation must conform to current Manufactured Home Construction & Safety

Standard (which is a Federal Regulation Title 24 CFR-Part 32-80) or when such

standard is not applicable, with American National Standard for

Mobile Homes.

Warning: The dryer is designed under ANSI Z21.5.1 standard

for home use only.

Installation in Mobile Home

DO

Correct

DON’T

Incorrect

DO

Correct

DON’T

Incorrect

11

The following are specific requirements for proper and safe

operation of your dryer. Failure to follow these instructions can create

excessive drying times and fire hazards.

WARNING

1. Do not use plastic flexible duct to exhaust the dryer. Excessive lint can build up

inside exhaust system and create a fire hazard and restrict air flow. Restricted

air flow will increase dryer times. If your present system is made up of plastic

duct or metal foil duct, replace it with a rigid or flexible metal duct. Ensure

present duct is free of any lint prior to installing dryer duct.

2. If the dryer is not exhausted outdoors, some fine lint will be expelled into the

laundry area. An accumulation of lint in any area of the home can create a

health and fire hazard. To reduce risk of fire, dryer MUST BE

EXHAUSTED OUTDOORS.

3. Do not allow combustible material (for example: clothing, draperies/curtains,

paper) to come in contact with exhaust system. The dryer must not be

exhausted into a chimney, a wall, a ceiling, or any concealed space of a

building which can accumulate lint, resulting in a fire hazard.

4. Exceeding the length of duct pipe or number of elbows allowed in the

“Maximum Length” charts can cause an accumulation of lint in the exhaust

system. Plugging the system could create a fire hazard, as well as increase

drying times.

5. Do not screen the exhaust ends of the vent system, or use any screws or rivets

to assemble the exhaust system. Lint can become caught in the screen, on the

screws or rivets, clogging the duct work and creating a fire hazard as well

as increasing drying times. Use an approved vent hood to terminate the duct

outdoors, and seal all joints with duct tape. All male duct pipe fittings must be

installed downstream with the flow of air.

Explosion hazard:

Do not install the dryer where gasoline or other flammables are kept or

stored. If the dryer is installed in a garage, it must be minimum of 18

inches (45.7 cm) above the floor. Failure to do so can result in death,

explosion, fire or burns.

Requirements and Instructions

EXHAUST SYSTEM CONNECTIONS

EnglishEnglish

12

EnglishEnglish

Materials

INSTALL MALE FITTINGS IN THE CORRECT DIRECTION

Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible metal duct and

approved vent hood that has a swing-out damper hat open when the dryer is

in operation. When the dryer stops, the dampers automatically close to prevent

drafts and the entrance of insects and rodents. To avoid restricting the outlet,

maintain a minimum of 12 inches (30.5 cm) clearance between the vent hood

and the ground or any other obstruction. The vent flap should be able to

move freely.

MAXIMUM EXHAUST LENGTH

"

13

After installation is completed, the following method must be used to

determine if the exhaust system is acceptable:

1. Connect an inclined or digital manometer between the dryer and the point the

exhaust connects to the dryer.

2. Set the dryer timer and temperature to air fluff (cool down) and start the dryer.

3. Read the measurement on the manometer.

4. The system back pressure must not be higher than 0.75 inches of water

column. If the system back pressure is less than 0.75 inches of water column,

the system is acceptable. If the manometer reading is higher than 0.75 inches

of water column, the system is too restrictive and the installation

is unacceptable.

Although vertical orientation of the exhaust system is acceptable, certain

extenuating circumstances could affect the performance of the dryer:

1. Only the rigid metal duct work should be used.

2. Venting vertically through a roof may expose the exhaust system to down

drafts causing an increase in vent restriction.

3. Running the exhaust system through an area not insulated may cause

condensation and faster accumulation of lint.

4. Compression or crimping of the exhaust system will cause an increase in

vent restriction.

The exhaust system should be inspected and cleaned a minimum of every 18

months with normal usage. The more the dryer is used, the more often you should

check the exhaust system and vent hood for proper operation.

EnglishEnglish

The following are specific requirements for proper and safe

electrical installation of your dryer. Failure to follow these instructions

can create electrical shock and/or fire hazard.

WARNING

Requirements and Instructions

ELECTRICAL CONNECTIONS

14

EnglishEnglish

1. This appliance must be properly grounded. Electrical shock can result if the

dryer is not properly grounded. Follow the instructions in this manual for

proper grounding.

2. Do not use an extension cored with this dryer. Some extension cords are not

designed to withstand the amounts of electrical current this dryer utilizes and

can melt, creating electric shock and/or fire hazard. Locate the dryer within

reach of the receptacle for the length power cord to be purchased, allowing

some slack in the cord. Refer to the electrical requirements in this manual for

the power cord to be purchased.

3. A U.L. approved strain relief must be installed onto power cord. If the strain

relief is not attached, the cord can be pulled out of the dryer and can be cut

by any movement of the cord, resulting in electrical shock.

4. Do not use an aluminum wire receptacle with copper wired power cord and

plug (or vice versa). A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The proper wiring and receptacle is

a copper wired power cord with a copper wired receptacle.

Note: Dryers operating on 208 Volt power supply will have longer drying times

than operating on 240 Volt power supply.

Danger: Improper connection of the equipment-grounding conductor can result in

a risk of electrical shock. Check with a licensed electrician if you are

in doubt as to whether the appliance is properly grounded. The dryer

must be connected to a grounded metal, permanent wiring

system, or an equipment-grounding conductor must be run with the

circuit conductors and connected to the equipment-grounding terminal

or lead on the appliance.

Power Supply:

3 or 4 wire, 240 Volt, 30 Amp, 60Hz, 1 Phase

Power Supply Cord Kit: (not supplied when sold in the United States)

The dryer MUST employ a 3-conductor power supply cord NEMA 10-30 type

SRDT rated at 240 Volt AC minimum, 30 Amp., with 3 open end spade lug

connectors with upturned ends or closed loop connectors and marked for use

with clothes dryers. If being installed in a manufactured (mobile) home, the dryer

MUST employ a 4-conductor power supply cord NEMA 14-30 type SRDT or ST

(as required) rated at 240 Volt AC minimum, 30 Amp., with 4 open end spade

lug connectors with upturned ends or closed loop connectors and marked for use

with clothes dryers. See Electrical Connections for A 4-Wire System.

15

3-Wire Cord Connections

1. Remove the screws securing the terminal block access cover and the strain

relief mounting bracket located on the back of the dryer upper corner.

2. Install a U.L. approved strain relief into the power cord entry hole of the

mounting bracket. Finger tighten the nut only at this time.

3. Thread a U.L. Approved 30 Amp. power cord, NEMA 10-30 Type SRDT,

through the strain relief.

4. Attach the power cord neutral (center wire) conductor to the silver-colored

center terminal on the terminal block. Tighten the screw securely.

5. Attach the remaining two power cord outer conductors to the outer brass

colored terminals on the terminal block. Tighten both screws securely.

WARNING: Do not make a sharp bend or crimp wiring/conductor

at connections.

6. Reattach the strain relief mounting bracket to the back of the dryer with two

screws. Tighten screws securely.

7. Tighten the screws securing the cord restraint firmly against the power cord.

8. Tighten the strain relief nut securely so that the strain relief does not turn.

9. Reinstall the terminal block cover.

green ground screw

green neutral

ground wire

strain relief

mounting bracket

silver terminal

nut

tighten nut

to these threads

power cord

EnglishEnglish

16

EnglishEnglish

4-Wire Cord Connections

1. Remove the screws securing the terminal block access cover and the strain

relief mounting bracket located on the back of the dryer upper corner.

2. Install a U.L. approved strain relief into the power cord entry hole of the

mounting bracket. Finger tighten the nut only at this time.

3. Remove the green neutral ground wire fom the green ground scrcew located

above the terminal block.

green ground screw

typical conductor

receptacle

typical 4

conductor cord

black 240V

white neutral

red 240V

green ground

30 AMP NEMA 14-30 TYPE SRDT OR ST

green power cord

ground wire

silver terminal

terminal block

black

white

green neutral

ground wire

red

power cord

strain relief

mounting bracket

nut

tighten nut to

these threads

17

4. Thread a U.L. approved 30 Amp power cord, NEMA 14-30 type ST or SRDT

through the strain relief.

5. Attached the green power cord ground wire to the cabinet with green

ground screw.

6. Attached the white (neutral) power cord conductor from the power cord and

the green ground wire from the dryer harness to the silver-colored center

terminal on the terminal block. Tighten the screw securely.

7. Attached the red and black power cord conductors to the outer brass-colored

terminals on the terminal block. WARNING: Do not make a sharp bend or

crimp wiring/conductor at connections.

8. Tighten the screws securing the cord restraint firmly against the power cord.

9. Tighten the strain relief nut securely so that the strain relief does not turn.

10. Reinstall the terminal block cover.

Caution: Label all wires prior to disconnection, when servicing

controls. Wiring errors can cause improper operations

and be dangerous. Check unit for proper operation

after servicing.

Warning: Discard or destroy the carton anbd plastic bags after the

dryer is unpacked. Children should not be allowed to use

them to play with. Cartons covered with rugs, bedspreads,

or plastic sheets can become an airtight chamber and cause

suffocation leading to death. Make all packing materials

inaccessible to children.

Warning: The instructions in this manual and all other literature

included with this dryer can not cover every possible

condition and situation that may occur. Good safe practice

and caution must be applied when installing, operating and

maintaining any appliances. After installing, if you

are in doubt, call a certified electrician to install and

wire the dryer.

EnglishEnglish

18

EnglishEnglish

It is your responsibility

• To connect a qualified electrical installer.

• To be sure that the electrical connection is adequate and in

conformance with CAN1-B149 (.1 or .2) installation codes and/or

local codes.

• A 4 wire, single phase, 115/230-volt, 60-Hz., AC-only electrical

supply is required on a separate 30-amp circuit, fused on both sides

of the line. A time-delay fuse or circuit breaker is recommended.

Connect to an individual branch circuit.

• This dryer is equipped with a CSA International Certified Power Cord

intended to be plugged into a standard 14-30R wall receptacle. The

cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach

of dryer’s final location.

• Do not modify the plug provided with the appliance: if it will not fit

the outlet, have a proper outlet installed by a qualified electrician.

4-wire receptacle 14-30R

If using a replacement power supply cord, it is recommended that you use Power

Supply Cord Replacement. For further information, please reference the service

numbers located in the “Assistance or Service” section of this manual.

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

Warning

(For Model HDY6-1C)

ELECTRICAL REQUIREMENTS (FOR CANADA)

19

Replacement Power Supply Cord must be:

• UL Listed or CSA International Certified

• Marked for use with clothes dryers

• Rated 115/230 volt minimum

• 30 amp

• Type SRD or SRDT

• 4 Conductors

• At least 5 ft (1.52 m) long.

Grounding Instructions

• For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown,

grounding will reduce the risk of electric current. This dryer is equipped

with a cord having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

Warning: Improper connection of the equipment-grounding conductor

can result in a risk of electric shock. Check with a qualified electrician

or service representative or personnel if you are in doubt as to whether

the dryer is properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet installed by a

qualified electrician.

Save These Instructions

EnglishEnglish

La page charge ...

Haier HDY6-1C Manuel utilisateur

Ce manuel convient également à

Haier HDY6-1C Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents