Windsor Saber Compact 20 Le manuel du propriétaire

86400640-B 07/22/15

Saber Compact 20

Walk Behind Scrubber

Operating Instructions (ENG)

MODELS: SC20

1.005-219.0

SC20T

1.005-220.0

SCX20T

1.005-237.0

SCC20

1.005-223.0

SCC20T

1.005-224.0

SCXC20T

1.005-242.0

From Serial Number (Ref No1*)

*See Serial Number Page in Spare

Parts List or call manufacturer.



IPX4

Warranty Registration

Thank you for purchasing a Kärcher North America product. Warranty registration is quick

and easy. Your registration will allow us to serve you better over the lifetime of the product.

To register your product go to :

http://warranty.karcherna.com/

For customer assistance:

1-800-444-7654

2 86400640 Operator’s Manual - Saber Compact 20

Machine Data Label

Overview

The Saber Compact is a battery powered, hard floor scrubber intended for commercial use. The appliance applies

a cleaning solution onto a hard floor, scrubs the floor with a brush or pad, and then vacuums the soiled water back

into the recovery tank.

3

Table of Contents

Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . . .2

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3

How To Use This Manual . . . . . . . . . . . . . . . . . . . . .4

Safety

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . .5

Hazard Intensity Level . . . . . . . . . . . . . . . . . . . . . . .7

Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Operations

Technical Specifications . . . . . . . . . . . . . . . . . . . . .10

How This Machine Works . . . . . . . . . . . . . . . . . . . .12

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Controls - Non Traction. . . . . . . . . . . . . . . . . . . . . .14

Controls - Traction . . . . . . . . . . . . . . . . . . . . . . . . .16

Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . .19

Pre-run Machine Inspection . . . . . . . . . . . . . . . . . .19

Starting Machine . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Emergency Stop Procedures . . . . . . . . . . . . . . . . .19

Filling Solution Tank . . . . . . . . . . . . . . . . . . . . . . . .19

Normal Scrubbing . . . . . . . . . . . . . . . . . . . . . . . . .19

Emptying And Cleaning Tanks . . . . . . . . . . . . . . . .21

Solution Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Maintenance

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

To Charge The Batteries. . . . . . . . . . . . . . . . . . . . .23

Changing Batteries . . . . . . . . . . . . . . . . . . . . . . . . .26

Scrub Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Finished Floors . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Squeegee Blades . . . . . . . . . . . . . . . . . . . . . . . . . .28

To Remove Squeegee Assembly . . . . . . . . . . . . . .28

Adjusting Deluxe Squeegee . . . . . . . . . . . . . . . . . .28

To Adjust Squeegee Pitch . . . . . . . . . . . . . . . . . . .29

To Adjust Amount Of Rear Squeegee Deflection . .29

To Replace Or Rotate Front Squeegee Blade . . . .29

Greasing Axles . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . .30

Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Suggested Spare Parts - Standard . . . . . . . . . . . . .34

Suggested Spare Parts - Deluxe . . . . . . . . . . . . . .35

86400640 Operator’s Manual - Saber Compact 20

4

How To Use This Manual

This manual contains the following sections:

• How To Use This Manual

•Safety

• Operations

• Maintenance

• Suggested Spare Parts

The HOW TO USE THIS MANUAL section will tell you

how to find important information for ordering correct

repair parts.

Parts may be ordered from authorized dealers. When

placing an order for parts, the machine model and

machine serial number are important. Refer to the

MACHINE DATA box which is filled out during the

installation of your machine. The MACHINE DATA box

is located on the inside of the front cover of this manual.

The model and serial number of your machine is on the

front of the control tower.

The SAFETY section contains important information

regarding hazardous or unsafe practices of the

machine. Levels of hazards are identified that could

result in product damage, personal injury, or severe

injury resulting in death.

The OPERATIONS section is to familiarize the operator

with the operation and function of the machine.

The MAINTENANCE section contains preventive main-

tenance to keep the machine and its components in

good working condition. They are listed in this general

order:

• Batteries

• Scrub Brushes

• Squeegee

• Service Schedule

• Machine Troubleshooting

NOTE: If a service or option kit is installed on your

machine, be sure to keep the KIT INSTRUCTIONS

which came with the kit. It contains replacement parts

numbers needed for ordering future parts.

NOTE: The manual part number is located on the

lower right corner of the front cover.

Model:

Date of Purchase:

Serial Number:

Dealer:

Address:

Phone Number:

Sales Representative:

86400640 Operator’s Manual - Saber Compact 20

5

Safety

IMPORTANT SAFETY INSTRUCTIONS

When using this machine, basic precaution

must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

To reduce the risk of fire, electric shock, or injury:

Use only indoors. Do not use outdoors or expose to rain.

Use only as described in this manual. Use only manufacturer’s recommended components and attachments.

If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it

to an authorized service center.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.

This machine is not suitable for picking up hazardous dust.

Do not operate this machine near flammable fluids, dust or vapors.

This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and

offices for more than normal housekeeping purposes.

Maintenance and repairs must be done by qualified personnel.

If foam or liquid comes out of machine, switch off immediately.

Disconnect battery before cleaning or servicing.

Before the machine is discarded, the batteries must be removed and properly disposed of.

Make sure all warning and caution labels are legible and properly attached to the machine.

During operation, attention shall be paid to other persons, especially children.

Before use all covers and doors shall be put in the positions specified in the instructions.

When leaving unattended, secure against unintentional movement.

The machine shall only be operated by instructed and authorized persons.

When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.

Only chemicals recommended by the manufacturer shall be used.

This appliance has been designed for use with the brushes specified by the manufacturer. The fitting of other

brushes may affect its safety.

Do not use on surfaces having a gradient exceeding 2%.

SAVE THESE INSTRUCTIONS

86400640 Operator’s Manual - Saber Compact 20

6

Safety

MESURES DE SÉCURITÉ IMPORTANTES

Lors de l’utilisation d’un appareil à batteries, il est nécessaire de respecter

systématiquement des mesures de sécurité de base, comme suit :

PRENEZ NOTE DE TOUTES CES MESURES AVANT D’UTILISER CETTE MACHINE

Pour réduire le risque d'incendie, d'électrocution ou de

blessure :

N’utiliser cette machine qu’en intérieur. Ne jamais l’utiliser à l’extérieur ou dans la pluie.

N’utiliser cette machine que comme décrit dans le présent manuel. N’utiliser que les composants et les acces-

soires conseillés par le fabricant.

Lorsque la machine ne fonctionnant pas correctement, a fait l’objet d’une chute ou d’une détérioration, a été

laissée à l’extérieur, est tombée dans l’eau, la retourner au centre de service agréé.

Ne pas opérer la machine lorsque les conduits de ventilation sont bloquées. Débarrasser les débris des conduits,

car ils peuvent réduire l’écoulement d’air.

Cette machine n’est pas adaptée au ramassage de poussières dangereuses

Ne pas l’utiliser près de liquides, de poussières ou de vapeurs inflammables.

Cette machine est destinée à un usage commercial. Elle est recommandée davantage pour les domaines hôtelier,

scolaire, hospitalier, industriel ou pour les bureaux, les chaînes de magasin, que pour un usage domestique

normal.

L’entretien et les réparations de la machine doivent être effectuées par un personnel qualifié.

Si de la mousse ou du liquide sort de la machine, la mettre hors tension immédiatement.

Déconnecter les batteries avant de nettoyer la machine ou de la soumettre à un entretien.

Avant de se débarrasser de la machine, il est nécessaire de retirer les batteries et de les jeter correctement.

S’assurer que toutes les plaques d’avertissement ou de précaution sont lisibles et fixées correctement sur la

machine.

Durant la manoeuvre de la machine, prendre garde aux personnes environnantes et notamment aux enfants.

Avant l’utilisation de la machine, veiller à positionner tous les couvercles et portes comme indiqué dans les

instructions.

Lorsque la machine est laissée sans surveillance, s’assurer qu’elle ne se déplace pas de manière accidentelle.

Cette machine ne doit être manoeuvrée que par un personnel expérimenté et qualifié.

Lorsque la machine est laissée sans surveillance, la mettre hors tension ou verrouiller l’interrupteur principal

afin d’empêcher un emploi non autorisé.

Seuls les produits chimiques recommandés par le fabricant doivent être utilisés.

Cette machine a été conçue pour être utilisée avec des brosses spécifiées par le fabricant.

L’utilisation d’autres brosses peut affecter sa sûreté.

N'employez pas sur des surfaces ayant un gradient de plus de 2%.

LIRE ET CONSERVER CES INSTRUCTIONS

86400640 Operator’s Manual - Saber Compact 20

7

Safety

The following symbols are used throughout this guide as indicated in their descriptions:

Hazard Intensity Level

There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY.

The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating

condition. Following is information that signals some potentially dangerous conditions to the operator or the equip-

ment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the

machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and understood.

In Flammable or Explosive areas.

In areas with possible falling objects

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use

manufacturer approved replacement parts.

Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep

solution tank in raised position when charging. Keep sparks and flames away from the batteries. Do not

smoke around batteries.

Disconnect batteries before working on machine. Only qualified personnel should work inside machine.

Always wear eye protection and protective clothing when working on or near batteries. Avoid skin contact

with the acid contained in the batteries.

Never allow metal to lie across battery tops.

86400640 Operator’s Manual - Saber Compact 20

8

Safety

Les symboles suivants sont utilisés dans tout ce manuel, tels que décrits ici :

NIVEAU D'INTENSITÉ DU DANGER

Il existe trois niveaux d'intensité du danger, identifiés par des termes d'avertissement - AVERTISSEMENT,

ATTENTION et POUR VOTRE SÉCURITÉ. Le niveau d'intensité du danger est déterminé par les définitions

suivantes :

AVERTISSEMENT - Les dangers ou des pratiques contraires à la sécurité qui POURRAIENT entraîner des

blessures personnelles ou la mort.

ATTENTION - Les dangers ou des pratiques contraires à la sécurité qui pourraient entraîner des blessures person-

nelles légères ou des dégâts sur le produit ou d'autres biens.

POUR DES RAISONS DE SÉCURITÉ : Pour identifier les actions qui doivent être exécutées pour un fonc-

tionnement sûr de l'équipement.

Signaler immédiatement tout dommage subi par la machine ou fonctionnement défectueux. Ne pas utiliser la

machine si elle ne fonctionne pas correctement. Ci-dessous se trouvent les informations indiquant les conditions

potentiellement dangereuses pour l'opérateur ou l'équipement. Lire attentivement ces informations. Être conscient

que ces conditions peuvent survenir. Repérer tous les dispositifs de sécurité sur la machine. Suivre les étapes

nécessaires de formation du personnel qui utilise la machine.

POUR DES RAISONS DE SÉCURITÉ :

NE PAS FAIRE FONCTIONNER LA MACHINE :

Sauf si le personnel est formé et autorisé.

Sauf si le manuel d'utilisation est lu et compris.

Dans des zones inflammables ou explosives.

Dans des zones contenant des objets susceptibles de tomber

LORS DE L'ENTRETIEN DE LA MACHINE :

Éviter les pièces mobiles. Ne pas porter de vêtements, vestes, chemises ou manches vagues lors de l'entretien de

la machine. Utiliser les pièces de rechange approuvées par le fabricant.

Les batteries émettent le gaz d'hydrogène. L'explosion ou le feu peut résulter. Étincelles de subsistance et flamme

nue loin. Compartiment de batterie de subsistance ouvert en chargeant. Étincelles et flammes de subsistance loin

des batteries. Ne fumez pas autour des batteries.

Déconnecter les batteries avant de travailler sur la machine. La machine ne doit être confiée qu’à un personnel

qualifié. Porter systématiquement des lunettes et des vêtements de protection lors d’une intervention sur les

batteries ou aux alentours. Éviter tout contact de la peau avec l’acide contenu dans les batteries.

Ne jamais placer d’objets métalliques sur le dessus des batteries.

86400640 Operator’s Manual - Saber Compact 20

9

Safety

Safety Labels

NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become

illegible, promptly replace them. Les schémas ci-dessous indiquent l’emplacement des plaques de sécurité. Si

les plaques deviennent illisibles, les remplacer immédiatement.

REMARQUE: Les schémas ci-dessous indiquent l’emplacement des plaques de sécurité. Si les plaques

deviennent illisibles, les remplacer immédiatement.

SAFETY DECAL

86252530

BATTERY CAUTION

86252520

86400640 Operator’s Manual - Saber Compact 20

10

Operations

Technical Specifications

Special Notes:

The A-weighted sound pressure level emitted by the appliance was measured to be 72.5 dBA. This is a space-

averaged, broad-band measurement determined according to IEC 704-I. This appliance contains no possible

source of impact noise. The overall root-mean-square acceleration at the operator’s arms was measured to be less

than 1.0m/s

2

. This is a tri-axial, broad-band measurement made during normal operation on a composite tile floor.

ITEM DIMENSION/CAPACITY

Nominal power – non-traction model 1100 W

Nominal power – traction model 1200 W

Rated Voltage 24VDC

Rated Amperage – non-traction model 45 Amps

Rated Amperage – traction model 50 Amps

Batteries

2 x 12 Volt 105-130-195 AH @ 20hr

rate

Scrub Brush Motor .75 hp (0.56 kW)

Vacuum Motor .75 hp (0.56 Kw)

Propelling Motor – traction model .38 hp (0.28 Kw)

Mass (GVW) – non-traction model 543 lbs. (246.5 kg)

Mass (GVW) – traction model 556 lbs. (252.4 kg)

Weight empty without batteries – non-traction model 213 lbs. (96.1 kg)

Weight empty without batteries – traction model 232 lbs. (105.3 kg)

Solution Control – non-traction model Gravity feed, fully variable

Solution Control – traction model

Gravity feed, fully variable with

automatic shut-off in neutral

Solution tank capacity 13 gal. (50 l)

Recovery tank capacity 16 gal. (60 l)

Scrub brush diameter 20 in (51 cm)

Scrub brush pressure – non-traction model 50 lbs. (23 kg)

Scrub brush pressure – traction model 100 lbs. (45 kg)

Scrub brush speed 200 rpm

Tires – non-traction model

2 x 8 in (20 cm) thermoplastic

elastomer non-marking

Tires – traction model 2 x 8 in (20 cm) foam filled non-marking

Casters

3.5 x 1.25 in (9 cm) polyurethane solid

non-marking

Foundation Pressure – non-traction model

105 lbs./in

2

( 725 kPa)

Foundation Pressure – traction model

46 lbs./in

2

( 315 kPa)

Maximum Speed – traction model 2.75 miles/hour (4.5 km/hour)

Frame Construction Steel with epoxy powdercoat finish.

Minimum aisle u-turn width 45 in. ( 114.3 cm)

Maximum rated climb and descent angle with empty tanks 2%

Maximum rated climb and descent angle with full tanks 2%

86400640 Operator’s Manual - Saber Compact 20

11

Operations

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure

that they do not play with the appliance.

Cet appareil n'est pas prévu à l'usage des personnes (enfants y compris) avec des possibilités physiques, sensori-

elles ou mentales réduites, ou le manque d'expérience et de connaissance, à moins qu'ils aient été donnés la

surveillance ou l'instruction au sujet de l'utilisation de l'appareil par une personne chargée de leur sûreté. Des

enfants devraient être dirigés pour s'assurer qu'ils ne jouent pas avec l'appareil.

ITEM MEASURE

Height 43 in. ( 109.2 cm)

Length 54 in. (137.1 cm)

Width without squeegee 22 in. (55.9 cm)

Width of squeegee 31 in. ( 78.7 cm)

Width of scrub path 20 in. (51 cm)

HEIGHT

LENGTH

WIDTH

86400640 Operator’s Manual - Saber Compact 20

12

Operations

How This Machine Works

The Saber Compact is a battery powered, hard floor

scrubber intended for commercial use. The appliance

applies a cleaning solution onto a hard floor, scrubs the

floor with a brush, and then vacuums the soiled water

back into the recovery tank.

The machine's primary systems are the solution

system, scrub system, recovery system. The traction

model has a directional control system as well.

The function of the solution system is to store cleaning

solution and deliver it to the scrub system. The solution

system consists of the solution tank, strainer, valve and

controls. The solution tank stores cleaning solution

(water and detergent) until it is delivered to the scrub

system. The strainer protects the valve from debris.

The non-traction model has a ball-type valve which

controls the delivery of cleaning solution to the scrub

system. The traction model has a solenoid type valve,

which controls the delivery of cleaning solution to the

scrub system. The valve automatically prevents

solution flow unless the scrub brushes are turned on

and the machine is being propelled. The solution

control knob controls the amount of cleaning solution

delivered to the scrub system.

The function of the scrub system is to scrub the floor.

The scrub system consists of a rotary type disk scrub

brush, motor, self-adjusting scrub deck skirt, lift linkage

and controls. The brush scrubs the floor and the motor

drives the brush. The brush drive hub allows the scrub

brush to follow irregularities and changes in the floor

without loosing contact with floor. The self-adjusting

scrub deck skirt controls the cleaning solution on the

floor so that the squeegee can pick it up. The brush lift

lever raises and lowers the scrub deck. On the traction

model the brush lift lever can be locked into an

increased brush pressured position.

The function of the recovery system is to vacuum the

soiled water back into the recovery tank. The recovery

system consists of the squeegee, vacuum motor,

screen, recovery tank and controls. The squeegee

wipes the dirty solution off the floor as the machine

moves forward. The vacuum motor provides suction to

draw the dirty solution off the floor and into the recovery

tank. The screen protects the vacuum fan from debris.

The recovery tank stores the dirty solution. The float

ball in the tank activates when the recovery tank is full.

On the traction model, the function of the directional

control system is to control the direction and speed of

the machine. The directional control system consists of

buttons, speed control knob/potentiometer, controller

and transaxle. The speed control knob actuates a

potentiometer, which signals speed. The controller

interprets the forward/reverse signals from the buttons

and the speed signal from the potentiometer to

command the transaxle to propel the machine in the

direction, and at the speed, desired.

The buttons on the control handles signal forward.

When the reverse button on the control panel is

pushed, in addition to either button on the control

handles, reverse is signaled.

86400640 Operator’s Manual - Saber Compact 20

13

Operations

Components

1. Control Panel

2. Control Handle

3. Recovery Tank

4. Recovery Tank Drain Hose

5. Scrub Head

6. Scrub Brush Access Cover

7. Solution Tank

8. Solution Tank Cover

9. Solution Tank Drain Hose

10. Solution Strainer

11. Solution Tank Support Arm

12. Squeegee

13. Vacuum Motor

86400640 Operator’s Manual - Saber Compact 20

7

6

5

13

11

8

2

1

4

9

12

3

10

14

Operations

Controls - Non Traction

1. Brush Switch

2. Brush Lift Lever

3. Vacuum Switch

4. Squeegee Lift Lever

5. Solution Control Lever

6. Battery Charge Level Indicator

7. Hour Meter (Optional)

8. Circuit Breakers

3

1

6

8

7

5

2

4

86400640 Operator’s Manual - Saber Compact 20

15

Operations

1. Brush Switch

Controls the scrub brush motor.

To turn scrub brush on, press the top of the switch.

To turn scrub brush off, press the bottom of the switch.

2. Brush Lift Lever

Raises and lowers the brush.

To lower the brush, lift the lever from the notch, move to

the left, then lower.

To raise the brush, lift the lever from its lowered

position.

3. Vacuum Switch

Controls the vacuum motor.

To start vacuum motor, press the top of the switch.

To stop vacuum motor, press the bottom of the switch.

4. Squeegee Lift Lever

Raises and lowers the squeegee.

To lower the squeegee, lift and pull the lever to the left

and then lower.

To raise the squeegee, lift the lever and push it to the

right.

5. Solution Control Lever

Controls solution flow to scrub deck.

To increase flow pull and raise the knob to the desired

flow.

To decrease flow push the knob down.

6. Battery Charge Level Indicator

Indicates the charge level of the batteries.

The meter display is divided into 10 vertical bars. Bars

illuminated on the far right indicate full charge. Bars

flashing near the left side indicate the batteries should

be recharged. Further operation of the machine could

damage the machine or the batteries.

When the machine is left overnight with less than a full

charge, the display may initially indicate a full charge. It

will also indicate a full charge if the batteries are

disconnected, then reconnected. After a few minutes of

operation the meter will give the correct charge level.

7. Hour Meter (Optional)

Records the number of hours the machine’s brush has

been in operation. This information is useful in deter-

mining when to service the machine.

8. Circuit Breakers

Circuit breakers interrupt the flow of power in he event

of an electrical overload. When a circuit breaker is

tripped, reset it by pressing the exposed button. If a

circuit breaker continues to trip, the cause of the elec-

trical overload should be found and corrected.

30 amp. Protects the scrub brush

motor.

30 amp. Protects the vacuum

motor.

86400640 Operator’s Manual - Saber Compact 20

16

Operations

Controls - Traction

1. Solution Control Knob

2. Brush Switch

3. Brush Lift Lever

4. Vacuum Switch

5. Squeegee Lift Lever

6. Key Switch

7. Propel Buttons (Normally Forward)

8. Reverse Propel Button

9. Speed Control Knob

10. Battery Charge Level Indicator

11. Emergency Shut Off Switch (Optional)

12. Hour Meter (Optional)

13. Circuit Breakers

1

4

8

2

6

9

10

5

7

3

13

11

12

86400640 Operator’s Manual - Saber Compact 20

17

Operations

1. Solution Control Knob

Controls solution flow to scrub deck.

To increase flow, rotate knob clockwise.

To decrease flow, rotate knob counterclockwise.

If the brush motor is turned off or the direction control

lever is in neutral, the flow is automatically interrupted

until the motor is turned on again. This feature

prevents unintentional draining of the solution tank and

allows the operator to adjust the solution flow to the

scrub deck without resetting each time the scrubbing

operation is interrupted.

2. Brush Switch

Controls the scrub brush motor.

To turn scrub brush on, press the top of the switch. The

brush will not rotate with the direction control lever in

neutral.

To turn the scrub brush off, press the bottom of the

switch.

3. Brush Lift Lever

Raises and lowers the brush.

To lower the brush, lift the lever from the notch, move to

the left, then lower.

To increase brush pressure, lock the lever into the

lowered position.

To raise the brush, lift the lever from its lowered position

and lock into highest notch.

4. Vacuum Switch

Controls the vacuum motor.

To start vacuum motor, press the top of the switch.

To stop vacuum motor, press the bottom of the switch.

5. Squeegee Lift Lever

Raises and lowers the squeegee.

To lower the squeegee, lift and pull the lever to the left

and then lower.

To raise the squeegee, lift the lever and push it to the

right.

6. Key Switch

Controls the power for machine functions.

To turn machine on, rotate key clockwise.

To turn machine off, rotate key counterclockwise.

FOR SAFETY: Always remove the key when

machine is unattended or during service to

prevent unauthorized movement.

7. Propel Buttons (Normally Forward)

Controls the machine direction, scrub brush and

solution flow.

To propel machine forward, push the button on either of

the control handles.

The scrub brush will not rotate and the solution will not

flow to the scrub deck unless a propel button is pushed.

8. Reverse Propel Button

Controls the machine direction in reverse.

To propel machine backward, push the button on the

control panel and one of the buttons on either of the

control handles.

86400640 Operator’s Manual - Saber Compact 20

18

Operations

9. Speed Control Knob

Controls the speed of the machine.

To increase speed, rotate knob clockwise.

To decrease speed, rotate knob counterclockwise.

10.Battery Charge Level Indicator

Indicates the charge level of the batteries.

The meter display is divided into 10 vertical bars. Bars

illuminated on the far right indicate full charge. Bars

flashing near the left side indicate the batteries should

be recharged. Further operation of the machine could

damage the machine or the batteries.

When the machine is left overnight with less than a full

charge, the display may initially indicate a full charge. It

will also indicate a full charge if the batteries are

disconnected, then reconnected. After a few minutes of

operation the meter will give the correct charge level.

11. Emergency Shut-off Switch (Optional)

Shuts off machine.

To shut off machine, push the switch.

To restart machine, rotate the switch clockwise.

12.Hour Meter (Optional)

Records the number of hours the machine’s brush has

been in operation. This information is useful in deter-

mining when to service the machine.

13.Circuit Breakers

Circuit breakers interrupt the flow of power in he event

of an electrical overload. When a circuit breaker is

tripped, reset it by pressing the exposed button. If a

circuit breaker continues to trip, the cause of the elec-

trical overload should be found and corrected.

3 amp. Protects the machine

controls

30 amp. Protects the scrub brush

motor.

30 amp. Protects the vacuum

motor.

25 amp. Protects the scrub brush

motor.

86400640 Operator’s Manual - Saber Compact 20

19

Operations

Machine Operation

Pre-run Machine Inspection

Do a pre-run inspection to find possible problems that

could cause poor performance or lost time from break-

down. Follow the same procedure each time to avoid

missing steps.

NOTE:

See maintenance section for pre-run

machine inspection checklist items.

Starting Machine

NOTE: Perform pre-run machine check before

operating machine.

FOR SAFETY:

Before starting machine, make

sure that all safety devices are in place and

operating properly.

1. Turn the machine power on.

2. Press the directional control button(s) to move in

the desired direction, if your machine is traction

model.

Emergency Stop Procedures

1. Release the directional control button(s), if your

machine is traction model.

2. Turn machine power off.

3. If an electrical problem is suspected push in

emergency stop button, if machine is equipped

with this option.

Filling Solution Tank

FOR SAFETY: Before leaving or servicing

machine; stop on level surface, turn off machine

and remove key.

1. Turn the machine power off.

2. Remove solution tank cover.

3. Fill the solution tank with clean water, leaving

enough room for the required amount of cleaning

solution. The solution tank capacity is 13 gallons

(50 liters). The water must not be hotter than 140°

F (60°C) to prevent damage to the tank.

4. Measure the chemical into the solution tank. Liquid

chemicals should be added to the solution tank

after filling with water. Dry chemicals should be

thoroughly mixed before being added into the

solution tank. Commercially available, high alkaline

floor cleaners, are suitable for use in the solution

system.

NOTE: Read the chemical manufacturers

recommended proportion instructions.

5.

Replace solution tank cover.

Flammable materials can cause an explosion or

fire. Do not use flammable materials in the tanks.

Les matières inflammables peuvent provoquer une

explosion ou un incendie. Ne pas utiliser de

matériaux inflammables dans les réservoirs.

Normal Scrubbing

Plan the scrubbing pattern in advance. The longest

track is around the perimeter of the area to be

cleaned. For efficient operation, the runs should be

the longest possible without

turning, stopping, or

raising and lowering scrub deck/squeegee.

NOTE: In order to achieve the best possible results,

the area which is to be cleaned should be swept

before scrubbing. Large debris, strings & wire must

be removed to prevent being caught in the brush or

squeegee.

86400640 Operator’s Manual - Saber Compact 20

INEFFICIENT SCRUBBING PATH

RECOMMENDED SCRUBBING PATH

20

Operations

To Begin Scrubbing

When operating the machine around people, pay

close attention for unexpected movement. Use

extra caution around children.

Lorsque vous utilisez la machine en présence de

gens, portez une attention particulière aux mouve-

ments inattendus. Soyez plus prudent, surtout en

présence d’enfants.

Flammable liquids and/or reactive metals can

cause explosions or fire! Do not pick up.

Les liquides inflammables et / ou les métaux

réactifs peuvent provoquer des explosions ou un

incendie ! Ne les ramassez pas.

1. Turn the machine power on.

2. Lower the squeegee.

3. Turn the vacuum on.

4. Lower the scrub brush to the floor.

5. Turn the scrub brush on (for traction model, brush

will start when machine is propelled).

6. Drive machine forward to begin scrubbing.

NOTE:

Shut machine off immediately if water or

foam is expelled from the machine.

7. Adjust the speed of the machine, solution flow and

scrub brush pressure as necessary.

NOTE: For non-traction model, the solution flow must

be shut off to prevent unintentional draining of

solution tank. For traction model, once solution flow

rate is set it is not necessary to shut off solution when

stopping scrubbing. Solution flow is automatically

shut off when the brush motor stops. When the brush

motor is activated, flow will automatically resume.

To Stop Scrubbing

1. Release the directional control button(s), if your

machine is traction model.

2. Turn the scrub brush off.

3. Raise the scrub brush.

4. Raise the squeegee.

5. Turn the vacuum off.

6. Turn the machine power off.

Double Scrub

For floors which are heavily soiled or have thick accu-

mulations of floor finish the machine may not clean

sufficiently with one pass. In these cases it will be

necessary to double scrub.

To double scrub, make the first pass over the surface

being cleaned with the squeegee up, vacuum off, the

solution on, and brush down and on. This allows the

solution to stay in contact with the soil while loosening

the surface accumulation with the brush. Allow time for

the first application to stay in contact with the floor. The

length of time between the first and second pass

depends on the amount of accumulation and the type of

chemical being used. A second scrubbing with the

squeegee down, vacuum on and again with solution

and brush on will further loosen the soil. The additional

application of solution will further assist the difficult

cleaning job.

FOR SAFETY:

When using machine, go slow on

inclines and slippery services.

86400640 Operator’s Manual - Saber Compact 20

La page est en cours de chargement...

Windsor Saber Compact 20 Le manuel du propriétaire

Windsor Saber Compact 20 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents