LG LP073CD2B Le manuel du propriétaire

Marque: LG

Modèle: LP073CD2B

Catégorie: Climatiseurs split-system

Taper: Le manuel du propriétaire

P/NO : MFL67646801

www.lg.com

http://www.lghvac.com

OWNER’S MANUAL

AIR CONDITIONER

Please read this manual carefully before operating

your set and retain it for future reference.

TYPE : Room Air Conditioner

ENGLISH ESPAÑOL

FRANÇAIS

2 Room Air Conditioner

Packaged Terminal Air Conditioner/Heat Pump Owner's Manual

TABLE OF CONTENTS

FOR YOUR RECORDS

Write the model and serial numbers here:

Model #

Serial #

You can find them on a label on the side of each unit.

Dealer's Name

Date Purchased

n Staple your receipt to this page in the event you need it

to prove date of purchase or for warranty issues.

READ THIS MANUAL

Inside you will find many helpful hints on how to use and

maintain your air conditioner properly. Just a little

preventive care on your part can save you a great deal of

time and money over the life of your air conditioner.

You'll find many answers to common problems in the chart

of troubleshooting tips. If you review our chart of

Troubleshooting Tips first, you may not need to call for

service at all.

PRECAUTION

• Contact an authorized service technician for repair or

maintenance of this unit.

• Contact the installer for installation of this unit.

• The air conditioner is not intended for use by young

children or invalids without supervision.

• Young children should be supervised to ensure that

they do not play with the air conditioner.

• When the power cord is to be replaced, replacement

work shall be performed by authorized personnel

only using only genuine replacement parts.

• Installation work must be performed in accordance

with the National Electric Code by qualified and

authorized personnel only.

Safety Precautions..........................3

Before Operation.............................7

Introduction ....................................8

Electrical Safety ..............................9

Installation .....................................11

Control Locations .........................13

Maintenance and Service ............19

Ownerʼs Manual 3

ENGLISH

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions

must be followed.

n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness

is classified by the following indications.

n Meanings of symbols used in this manual are as shown below.

WARNING

CAUTION

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

WARNING

n Installation

Don't do this!

Be sure to follow the instruction.

Donʼt use a power cord, a

plug, or a loose socket

which is damaged.

• It may cause a fire or electrical

shock.

Always plug into a grounded

outlet.

• It may cause a fire or electrical

shock.

Do not modify or extend the

power cord length.

• It will cause electric shock or fire

due to heat generation.

Do not disassemble or

modify products.

• It may cause failure and

electric shock.

Be caution when unpacking

and installing.

• Sharp edges may cause

injury.

Do not use the power cord near

flammable gas or combustibles

such as gasoline, benzene,

thinner, etc.

• It may cause explosion or fire.

Gasolin

4 Room Air Conditioner

Safety Precautions

n Operation

Do not place the power cord

near a heater.

• It may cause fire and electric

shock.

Do not allow water to run

into electric parts.

• It will cause failure of machine or

electric shock.

Use a soft cloth to clean. Do

not use wax, thinner, or a

strong detergent.

• The appearance of the air

conditioner may deteriorate,

change color, or develop

surface flaws.

Wax

Thinner

Ventilate the room well when

using this appliance

together with a stove, etc.

• Oxygen depletion could occur.

Turn off the power and

breaker when cleaning the

unit.

• Moving parts could cause injury.

Turn off the main power

switch when not using it for

a long time.

• Prevent accidental startup and

the possibility of injury.

Unplug the unit if strange

sounds, odors, or smoke

come from it.

• It could represent a fire hazed.

Do not open the suction

inlet grill of the product

during operation.

• Otherwise, it may electrical

shock and failure.

If water enters the product, turn

off the the power switch of the

main body of appliance. Contact

service center after taking the

power plug out from the socket.

Do not place objects on the

power cord. Protect the

cord from being pinched or

damaged.

• There is danger of fire or electric

shock.

Use a dedicated circuit for

this appliance.

• An overloaded circuit is a fire

hazard.

Take the power plug out if

necessary, holding the end

of the plug and do not touch

it with wet hands.

• It may cause a fire or electrical

shock.

Ownerʼs Manual 5

ENGLISH

Safety Precautions

CAUTION

n Installation

Do not operate or stop the

unit by inserting or pulling

out the power plug.

• It will cause electric shock or fire

due to heat generation.

Do not damage or use an

unspecified power cord.

• It will cause electric shock or fire.

Do not operate with wet

hands or in damp

environment.

• It will cause electric shock.

Hold the plug by the end

when taking it out.

• It may cause electric shock and

damage.

When gas leaks, open the

window for ventilation

before operating the unit.

• Otherwise, it may cause an

explosion and a fire.

Never touch the metal parts

of the unit when removing

the filter.

• They are sharp and may cause

injury.

Install the product so that the noise or

exhaust from the outdoor unit may not

cause any damage to the neighbors.

• Be considerate of your neighbor.

Be sure the product is level front-to-back

and side-to-side when installing.

• It may cause vibration or water leakage.

For inner cleaning, contact an Authorized Service Center or a dealer.

Do not use harsh detergent that causes corrosion or damage on the unit.

• Harsh detergent may also cause failure of product, fire, or electronic shock.

6 Room Air Conditioner

Safety Precautions

n Operation

Be cautious not to touch the

sharp edges when installing.

• A severe cut or other injury could result.

Avoid excessive cooling and

perform ventilation sometimes.

• Use the ventilation function to circulate

air without cooling or heating

Do not insert hands or other

objects through the air inlet or

outlet during operation.

• Electrical and moving parts could cause

shock or injury.

If the liquid from the batteries gets onto your skin or

clothes, wash it well with clean water. Do not use the

remote if the batteries have leaked.

• The chemicals in batteries could cause burns or other health

hazards.

If you eat the liquid from the batteries, brush your teeth

and see doctor. Do not use the remote if the batteries

have leaked.

• The chemicals in batteries could cause burns or other health

hazards.

Do not put a pet or house plant

where it will be exposed to direct

air flow.

• It is not good to sit in the draft.

Do not block the inlet or outlet of

air flow.

• It may cause product failure.

Use a soft cloth to clean. Do not

use wax, thinner, or a strong

detergent.

• The appearance of the air conditioner

may deteriorate, change color, or

develop surface flaws.

Do not step on the indoor/outdoor

unit and do not put anything on it.

• It may cause an injury through dropping

of the unit or falling down.

Always insert the filter securely.

Clean it every two weeks.

• Operation without filters will cause

failure.

Do not drink water drained from

the air conditioner.

• It contains every contaminant

condensed from the air and could cause

health issues.

Ownerʼs Manual 7

ENGLISH

Before Operation

1. Contact an installation specialist for installation.

This is NOT a do-it-yourself project.

2. Plug in the power plug properly.

3. Use a dedicated circuit.

4. Do not use an extension cord. Consult a professional installer or electrician.

5. Do not start/stop operation by plugging/unplugging the power cord.

6. If the cord/plug is damaged, replace it with only an authorized replacement

part.

1. Being exposed to direct airflow for an extended period of time could be

hazardous to your health. Do not expose occupants, pets, or plants to direct

airflow for extended periods of time. In other words, don't sit in the draft.

2. Due to the possibility of oxygen deficiency, ventilate the room when used

together with stoves or other heating devices.

3. Do not use this air conditioner for non-specified special purposes (e.g.

preserving precision devices, food, pets, plants, and art objects). Such usage

could damage the items.

1. Do not touch the metal parts of the unit when removing the filter. Injuries can

occur when handling sharp metal edges.

2. Do not use water to clean inside the air conditioner. Exposure to water can

destroy the insulation, leading to possible electric shock.

3. When cleaning the unit, first make sure that the power and breaker are turned

off. The fan rotates at a very high speed during operation. There is a

possibility of injury if the unitʼs power is accidentally triggered on while

cleaning inner parts of the unit.

For repair and maintenance, contact your authorized service dealer.

Preparing for Operation

Usage

Cleaning and Maintenance

Service

8 Room Air Conditioner

Introduction

This symbol alerts you to the risk of electric shock.

This symbol alerts you to hazards that could cause harm to

the air conditioner.

This symbol indicates special notes.

NOTICE

This appliance should be installed in accordance with the National Electric Code.

Expanded Metal Grille Should be applied for better performance in PTAC and PTHP Units.

For Installation purpose and better appearance Aluminium or Architectural grille can be applied in

PTAC and PTHP Units.

Introduction

Symbols Used in this Manual

Features

INDOOR

REAR GRILLE

(Aluminum Rear Grille)

EXPANDED METAL GRILLE

(For Superior Performance)

LG PTAC and PTHP test condition

is recommended with expanded

metal grille

SLEEVE ASSEMBLY

(Including Aluminum Rear Grille)

THE SLEEVE AND THE REAR GRILLE

(Available as an option)

VERTICAL AIR DEFLECTOR

(Horizontal Louver)

AIR FILTER

INLET GRILLE

(Air Intake)

Ownerʼs Manual 9

ENGLISH

Electrical Safety

Electrical Data

230V~ 265V~

Power cord may include a current interrupter device.

A test and reset button is provided on the plug case.

The device should be tested on a periodic basis by first

pressing the TEST button and then the RESET button.

If the TEST button does not trip or if the RESET button

will not stay engaged, discontinue use of the air

conditioner and contact a qualified service technician.

Use Wall Receptacle Power Supply

Standard 208/230V, 3-wire

grounding receptacle rated 15A

Standard 208/230V, 3-wire

grounding receptacle rated 20A

Standard 208/230V, 3-wire

grounding receptacle rated 30A

Standard 265V grounding

receptacle rated 20A

Standard 265V grounding

receptacle rated 30A

Use 15 AMP. time

delay fuse or 15 AMP.

Circuit breaker.

Use 20 AMP. time

delay fuse or 20 AMP.

Circuit breaker.

(2500W Heater ơ15AMP.

Circuit Breaker)

Use 30 AMP. time

delay fuse or 30 AMP.

Circuit breaker.

Use 20 AMP. time

delay fuse or 20 AMP.

Circuit breaker.

Use 30 AMP. time

delay fuse or 30 AMP.

Circuit breaker.

Never push the test button during

operation

Otherwise this plug can damaged.

This device contains chemicals, including

lead, known to the State of California to

cause cancer, birth defects, or other

reproductive harm.

Wash hands after handling.

Do not remove, modify, or immerse this plug.

If this device trips, the cause should be

corrected before further use.

The conductors inside this cord are

surrounded by shields, which monitor

leakage current.

These shields are not grounded.

Periodically examine the cord for any

damage. Do not use this product in the

event the shields become exposed.

Avoid shock hazard! This unit cannot

be serviced. Opening the tamper-

resistant, sealed portion of the unit

voids all warranties and performance

claims. This unit is not intended to be

an ON/OFF switch.

The shape may be different according to its model.

NOTICE

DO NOT USE AN EXTENSION CORD on 230,

208, and 208/230, 265 Volt units.

All wiring should be made in accordance with local

electrical codes and regulations.

Aluminum house wiring may pose special

problems. Consult a qualified electrician.

NOTICE

10 Room Air Conditioner

Electrical Safety

IMPORTANT

(PLEASE READ CAREFULLY)

FOR THE USER'S PERSONAL SAFETY, THIS

APPLIANCE MUST BE PROPERLY GROUNDED

The power cord of this appliance is equipped with a

three-prong (grounding) plug. Use this with a standard

three-slot (grounding) wall power outlet to minimize

the hazard of electric shock. The customer should

have the wall receptacle and circuit checked by a

qualified electrician to make sure the receptacle is

properly grounded.

DO NOT CUT OR REMOVE THE THIRD (GROUND)

PRONG FROM THE POWER PLUG.

A. SITUATIONS WHEN THE APPLIANCE WILL BE

DISCONNECTED OCCASIONALLY

Because of potential safety hazards, we strongly

discourage the use of an adapter plug. However, if

you wish to use an adapter, a TEMPORARY

CONNECTION may be made. Use UL-listed adapter,

available from most local hardware stores.

The large slot in the adapter must be aligned with the

large slot in the receptacle to assure a proper polarity

connection.

Attaching the adapter ground terminal to the wall

receptacle cover screw does not ground the

appliance unless the cover screw is metal, and not

insulated, and the wall receptacle is grounded

through the house wiring. The customer should

have the circuit checked by a qualified electrician to

make sure the receptacle is properly grounded.

Disconnect the power cord from the adapter, using

one hand on each. Otherwise, the adapter ground

terminal might break. DO NOT USE the appliance with

a broken adapter plug.

B. SITUATIONS WHEN THE APPLIANCE WILL BE

DISCONNECTED OFTEN

Do not use an adapter plug in these situations.

Unplugging the power cord frequently can lead to an

eventual breakage of the ground terminal. The wall

power outlet should be replaced by a three-slot

(grounding) outlet instead.

USE OF EXTENSION CORDS

Because of potential safety hazards, we strongly

discourage the use of an extension cord. However, if

you wish to use an extension cord, use a CSA

certified/UL-listed 3-wire (grounding) extension cord.

Electrical Safety

Ownerʼs Manual 11

ENGLISH

Installation

How to Install the Unit

Installation

406 mm

(16")

406 mm

(16")

1,066 mm

(42")

1066 mm

(42")

318 mm

(12

318 mm

(12

505 mm

(20")

Over 20"

HEAT

RADIATION

WALL

INSULATION

SLEEVE

INTAKE

AIR

COOLED

AIR

1/4" Bubble

of the level

Over 20"

Front

Insulation Strip

Rear

Sleeve

280 mm

(11")

Insulation

Joint Gap

• There are sharp edges that can cause serious cuts.

• If the unit is to be installed close to the seaside, it needs

additional treatment on the heat exchanger.

• When lifting the air conditioner, it is HEAVY.

Use 2 people to lift.

For existing sleeve, you should measure the wall sleeve

dimensions.

You can install the new air conditioner according to these

installation instructions to achieve the best performence. All

wall sleeves used to mount the new air conditioner must be in

good structural condition and have the rear grille that securely

attaches to the sleeve or the flange of the sleeve to secure the

new air conditioner.

• To avoid vibration and noise, make sure the unit is installed

securely and firmly.

When installing the sleeve & Front grille, make certain there is

nothing within 20” back & front of sleeve & front grille, that

would interfere with heat radiation and exhaust air flow.

• Before installation, Check the insulation on the inner side of

the sleeve. If there is no insulation, place the insulation.

• Check the bottom corner's joint gap of the sleeve, If there is,

fill the gap with putty.

To maintain the best performance

of LG PTAC

1. An insulation strip must be attached. The

insulation strip is provided with the box.

2. After assembly of sleeve & Front grille, the

gap should be 20” from both sleeve &

grille. For assembly PTAC Model refer the

diagram given below.

1) Take out the insulation strip from the upper packing.

2) Attach the insulation strip onto the rear upper side of the

wall sleeve.

3) If anyone would like to improve unit energy efficiency, it is

recommended the change of outside grille for an unit

protection and an addition of a plastic rear grille. (This is

optional.)

NOTICE

Dimension of air conditioner

Dimension of sleeve assembly (optional)

12 Room Air Conditioner

Installation

• UNIT INSTALLATION

1. Remove the shipping screw from the ventilation door.

2. Remove the front gille by pulling it out at the bottom

to release it, then lift it up along the unit top front.

3. Slide the unit into the wall sleeve and secure with

6 screws through the unit flange holes.

4. Reinstall the front grille by hooking the top over the

unit top, then pushing it in at the bottom.

• Failure to follow this caution may result in equipment

damage or improper operation.

• Blocking indoor(curtain or bedclothes etc.) or outdoor

discharge air could cause premature failure of unit.

Ownerʼs Manual 13

ENGLISH

Control Locations

Manual Controls

• VENTILATION

The ventilation lever is located to the lower left side

of the unit.

The ventilation lever must be in the CLOSE position in

order to maintain the best cooling conditions.

When fresh air is necessary in the room, set the

ventilation lever to the OPEN position.

The damper is opened and outdoor air is drawn

into the room.

This will reduce the cooling or heating efficiency.

When the air conditioner has been running and is

turned off or set to the fan position, wait at least 3

minutes before resetting to the cooling operation.

Note:

A slight heat odor may come from the unit

when first switching to HEAT after the

cooling season is over.

This odor, caused by fine dust particles on

the heater, will disappear quickly.

This is harmless.

VENT

OPEN

VENT

14 Room Air Conditioner

Control Locations

Electronic Controls

The controls will look like one of the following.

TEMP

MODE

HEAT

E/SAVE

FANFAN

COOLCOOL

HIGHHIGH

LOWLOW TIMERTIMER

FAN TIMER

OFF

POWER

MODE

Push this button to cycle through the modes from COOL ’ FAN

’ HEAT’ COOL.

- COOL

• Fan runs continually for normal cooling operation.

- ENERGY SAVER

• The fan stops when the compressor stops cooling.

Approximately every 3 minutes the fan will turn on and the unit

will check the room air temperature to determine if cooling is

needed.

- FAN

• Fan operation without heating or cooling.

- HEAT

• Fan runs continually for normal heating operation.

TIMER

- SHUT-OFF TIME

• You will usually use shut-off time while you sleep.

• If unit is running, use Timer to set number of hours until shut-off.

• For your sleeping comfort, once Time is set, the Temperature setting will raise 2°F(1°C) after 30 minutes, and once

again after another 30 minutes.

• Push Timer to cycle through the settings from 1 Hour ’ 2 Hours ’ ... ’ 12 Hours maximum.

TEMPERATURE SETTING

• Use this button to automatically control the

temperature of the room.

The temperature can be set within a range of 54

°F(12°C) to 86°F(30°C) by increments

of 1°F(0.5℃).

• The setting appears in the display.

FAN SPEED

• Every time you push this button, it cycles through the settings as follows:

{High(F2) ’ Low(F1) ’ High(F2) ’ Low(F1)}

• To turn the air conditioner ON, push this button.

To turn the air conditioner OFF, push the button

again.

• This button takes priority over any other button.

Control Locations

Owner’s Manual 15

ENGLISH

Self-Diagnosis

FUNCTION:

If the unit has a malfunction, a green OPERATION LED located on the Display PCB used by the unit to

indicate the errors.

USE:

If the customer has to register a complaint to the service center, he can be very clear about registering

the complaint that what is happening & by referring the user's manual the customer can clearly define

the problem.

So that the engineer should go fully prepared with the prescribed tools to be used regarding that

problem. It also keeps the customer aware about the unit.

Here are some of the problems defined below for which the LED indicates by flashing.

The errors are the mentioned which is as follows:

• Electrical Controls

• Overheating Protection

This feature prevents melting of unit by electrical heater located inside of the unit at the remote

mode (when the unit is connected with wall thermostat). LED on the control panel displays

"OP"

• Freeze Protection

This feature prevents freezing of room at low temperature.

LED on the control panel displays "FP"

NOTICE

ON Normal

OFF No power / failed board

Fault Codes

CH 01

Indoor Air Thermistor Error

CH 02

Indoor Coil Thermistor Error

CH 07

Themostat Wiring Error

CH 09

EEPROM Check Sum Error

CH 10

Indoor Fan Error

CH 34

High Pressure Switch Error

CH 44

Outdoor Air Thermistor Error (PTHP Only)

CH 45

Outdoor Coil Thermistor Error (PTHP Only)

CH 67

Outdoor Fan Error

16 Room Air Conditioner

Control Locations

Additional Controls

• REMOVING THE FRONT GRILLE

Additional controls are available after

removing the front grille and option

cover of control box.

To remove the front grille, pull out the

bottom of front grille and then lift up.

To replace the front grille, place the tabs

over the top of the unit and push the

bottom of front grille until the clips snap

into place.

• ADDITIONAL CONTROLS

The additional controls are located behind the option cover of control box. The standard settings will be in

the OFF position. The authorized servicer has to check switches and ensure the switches are in the desired

position.

• TEMPERATURE LIMITING

Temperature Limiting can save money by limiting the lowest temperature for cooling and the highest

temperature for heating. The temperature limiting is controlled by switches #3 - #5.

This temperature limiting is not available with the Remote Wall Thermostat.

LOCAL

OFF

LOCAL

OFF

LOCAL

OFF

ONREMOTE

OFF

ON ON ON

Remote/Local

Energy Saver

Temperature Limit 1

Temperature Limit 2

Temperature Limit 3

PTAC/PTHP

UNIT TYPE

LOCALLOCAL

OFFOFF

LOCAL

OFF

LOCALLOCAL

OFFOFF

LOCAL

OFF

LOCALLOCAL

OFFOFF

LOCAL

OFF

OFF OFF OFF 54°F (12.2°C)

86°F (30.0°C)

54°F (12.2°C)

86°F (30.0°C)

ON OFF OFF 56°F (13.3°C) 84°F (28.9°C)

OFF ON OFF 58°F (14.4°C) 82°F (27.8°C)

ON ON OFF 60°F (15.5°C) 80°F (26.7°C)

OFF OFF ON 62°F (16.6°C) 78°F (25.5°C)

ON OFF ON 64°F (17.7°C) 76°F (24.4°C)

OFF ON ON 66°F (18.9°C) 74°F (23.3°C)

ON ON ON 68°F (20.0°C) 72°F (22.2°C)

Temperature Temperature Temperature

Limit 1 Limit 2 Limit 3

#3 #4 #5

Lowest Temp. Highest Temp. Lowest Temp. Highest Temp.

noitarepO gnitaeHnoitarepO gnilooC

Cooling+Electric Heater+Heat PumpOFFOFF

Cooling+Electric HeaterONOFF

Cooling Only

Heat Pump Only

Unit Type

OFF

86°F (30.0°C)

• REMOTE/LOCAL CONTROL

When remote/local switch #1 is on, it allow the unit to operate by the Remote Wall Thermostat.

The unit control by knobs are not available.

• ENERGY SAVER

The energy saver switch #2 is on. This switch is set at cycle fan to provide continuous fan operation in cool

or heat modes. When the switch is off the continuous fan allows continuous circulation of room air and

make the more balanced temperature of the room. When the switch is on, the fan is on or off with the

compressor or with the heater.

• FRONT DESK CONTROL

When the pair wire is connected to the connector FD2 and FD1, the unit can be turned ON or OFF with a

switch located at the Front Desk Control panel. When the front desk switch is ON, the fan operates

according to the setting without working compressor and heater. When the front desk switch is OFF, the unit

can operate according to the setting of controls.

• REMOTE WALL THERMOSTAT

When the wires are connected, the unit will be controlled

by a remote wall thermostat.

The thermostat connections supply the 24 Volt AC. When

you install the digital/electronic thermostat, you must set it

to 24 Volt AC. See the installation Instruction in this manual

for the Remote Wall Thermostat.

Wiring Schematic for

Straight Cool Unit.

Wiring Schematic for

Remote Heat Pump

Note: The following figures show wiring

schematics for heat pump and straight cool

units with electric heat, respectively.

GL GH O W Y R C

Low Fan

High Fan

Reversing Valve

Heater

Compressor

24 Volt-L

24 Volt-N

Wire # AWG Maximum Length

#22 600 ft (180 m)

#20 900 ft (270 m)

#18 1500 ft (450 m)

#16 2000 ft (610 m)

FD2 FD1 DR2 DR1 MS2 MS1

Front Desk Control

Door Switch

Motion Sensor

(Molex Housing Spec 396-06V)

(Molex Housing Spec 396-07V)

Room Air Conditioner 17

Control Locations

ENGLISH

18 Room Air Conditioner

Control Locations

1. Remove the front grille.

2. To remove the front grille, pull out the bottom

of the front grille and then lift up.

Re-install the component by referring to the

removal procedure.

3. To replace the front grille, place the tabs over

the top of the unit and push the bottom of front

grille until the clips snap into place.

• This Room Air Conditioner (PTAC) discharges

air from the top of the unit through reversible, 2-

position discharge grille louvers. The unit is

shipped from the factory with the discharge grille

louvers at an angle of 40˚ off vertical. In an

alternate position the louvers will be at an angle

of 15˚ off vertical.

To adjust the air direction, remove the front

grille. Remove the 4 screws that fasten the

discharge grille to the front grille.

Flip the discharge grille 180°, then reattach the

discharge grille to the front grille with 4 screws.

Disassembly Instructions

- Before the following disassembly, POWER SWITCH is set to OFF and disconnected the power

cord.

40˚

15˚

Screws

Maintenance and Service

Ownerʼs Manual 

Maintenance and Service

Air Filter Cleaning

Vent Filter

TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET.

The air filter should be checked at least twice a month to see if cleaning is necessary.

Trapped particles in the filter will build up and block the airflow. This reduces the cooling

capacity and also causes an accumulation of frost on the cooling coils.

If the filter becomes turn or damaged you should replace

immediately. Replacement filters are available from your

salesperson, dealer, and the authorized customer service

centers.

1. Remove the air filter from the front grille assembly by

pulling the air filter up slightly.

2. Wash the filter using lukewarm water below 104° F(40°C).

3. Gently shake the excess water from the filter completely.

Replace the filter.

Before cleaning the vent filter, disconnect power to the

unit by unplugging the power cord at the wall outlet or

subbase, or disconnect power at the fuse box or circuit

breaker. If unit is operated with vent door closed, the

vent filter does not need to be cleaned.

1. Remove the cabinet front as described in Front

Removal.

2. Remove the six screws securing the chassis to the

wall sleeve with a Phillips-Head screwdriver.

3. Slide the chassis out of the wall sleeve far enough so

that the vent filter is accessible as shown in Figure A.

4. Remove the vent filter by unscrewing the two screws

at the top of the filter and gently pulling the filter away

from the partition panel. Refer to Figure B.

5. Clean and replace the filter by reattaching the hook

to the bottom of the vent door and replacing the two

screws, slide the chassis back into the wall sleeve,

secure it in place with six screws and reinstall the

front cabinet.

Figure A – Vent (Left side of unit)

Figure B – Vent Filter Removal

ENGLISH

20 Room Air Conditioner

Maintenance and Service

Chassis

Drainage

Cabinet Front

Corrosion Resistant Models

Compressor / Fan Motor

The chassis must be cleaned every four months or more often as the atmospheric conditions

require. Use water and detergent to clean the basepan, center partition and coils. The use of harsh

cleaning materials may cause a deterioration of the coil fins or endplates. Do not use a high

pressure cleaner as it could cause severe damage to the PTAC fins and coils. A hose is okay to use

to clean the coils, but make sure to cover the control with a blanket or plastic bag to keep it dry.

Corrosion Resistant units operating in harsh atmospheric conditions must be removed from the

sleeve and cleaned every 3 months in the same manner as above.

The base pan may overflow due to high humidity.

To drain the excess water, remove the drain cap

from the back of the unit.

The compressor and fan motor are hermetically sealed, permanently lubricated, and require no

additional oiling.

The cabinet front and discharge air grille can be cleaned with a mild soap or detergent. Under no

circumstances should hydrocarbon based cleaners (e.g. acetone, benzene, naphtha, gasoline, etc.)

be used to clean the front or air grilles.

Use care when cleaning the control area. Do not use an excessively wet cleaning cloth.

Corrosion resistant models subjected to harsh seacoast environments must be removed from the

wall sleeve and completely flushed with clean water at least four times a year. The basepan, center

partition, condenser end plates, and the condenser itself should be sprayed with clean, fresh water.

Leaving the unit in the sleeve and simply spraying the outdoor grille is not sufficient.

Drain Cap

La page charge ...

LG LP073CD2B Le manuel du propriétaire

Marque: LG

Modèle: LP073CD2B

Catégorie: Climatiseurs split-system

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: LG LP073CD2B Owner's manual
español: LG LP073CD2B El manual del propietario

LG LP073CD2B Le manuel du propriétaire

LG LP073CD2B Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents