NAPOLEON NEFI24H Le manuel du propriétaire

EN

W415-1461 / D / 08.29.18

FR

PG

25

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.16F

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonﬁ replaces.com •[email protected]

SAFETY INFORMATION

!

WARNING

If the information in these instructions

are not followed exactly, a ﬁ re may result

causing property damage, personal injury

or loss of life.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

$10.00

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 1278

NEFI24H/NEFI27H

ELECTRIC LOGSET INSERT

NEFI24H ILLUSTRATED

EN

W415-1461 / D / 08.29.18

2

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INTRODUCTION 3

1.1 DIMENSIONS 4

1.2 LISTING APPROVALS 5

1.3 GENERAL INSTRUCTIONS 5

1.4 RATING PLATE INFORMATION 6

1.5 LABEL LOCATION 6

2.0 LOCATING LOG SET 7

2.1 UNPACKING AND TESTING LOG SET 7

2.2 GROUNDING LOG SET 7

3.0 INSTALLATION 8

3.1 LOG SET INSTALLATION 8

3.1.1 INSTALLING LOG SET INTO EXISTING FIREPLACE 8

3.1.2 INSTALLING LOG SET INTO MANTEL 9

3.2 HARD WIRING INSTALLATION 10

3.3 SECURING THE LOG SET 11

4.0 OPERATING INSTRUCTIONS 12

4.1 OPERATING CONTROL PANEL 12

4.2 OPERATING BY REMOTE CONTROL 13

4.3 REMOTE BATTERY INSTALLATION 13

5.0 FINISHING 14

5.1 NEFI24H LOG PLACEMENT 14

5.2 NEFI27H LOG PLACEMENT 14

5.3 EMBER BED PLACEMENT 15

5.4 CHARCOAL EMBER PLACEMENT 16

6.0 WIRING DIAGRAM 17

7.0 REPLACEMENT PARTS 18

7.1 NEFI24H OVERVIEW 19

7.2 NEFI27H OVERVIEW 20

8.0 TROUBLESHOOTING 21

9.0 WARRANTY 22

10.0 NOTES 23

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your municipality

for recycling instructions.

Les piles doivent être mises au rebut conformément aux lois et à la réglementation locales. Certaines

piles peuvent être recyclées et acceptées dans votre centre de recyclage local. Renseignez-vous auprès

de votre municipalité au sujet des directives de recyclage.

EN

3

1.0

INTRODUCTION

!

WARNING

C

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF

CONTACTED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate

appliance according to operating instructions could cause ﬁ re or injury.

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before

servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.

• Do not install damaged, incomplete or substitute components.

• Do not burn wood or other materials in this appliance.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,

install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the

room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.

• It is imperative that the control compartments, circulating blower and its passageway in the appliance

and are kept clean. The appliance should be inspected before use and at least annually by a qualiﬁ ed

service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and

other ﬂ ammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the

glass should be done by a licensed or qualiﬁ ed service person.

• Do not strike or slam shut the appliance glass door.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Servicing should be done only while the appliance is disconnected from the power supply circuit.

• Always unplug appliance when not in use.

• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been

dropped or damaged in any manner. Return appliance to authorized service facility for examination,

electrical or mechanical adjustment, or repair.

• Do not use outdoors.

• Never locate appliance where it may fall into a bathtub or other water container.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord

away from trafﬁ c area and where it will not be tripped over.

• Connect to properly grounded outlets only.

• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an

electric shock or ﬁ re, or damage the appliance.

• To prevent a possible ﬁ re, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a carpet, where openings may become blocked.

• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or

relocatable power tap (outlet/power strip).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a T.V. or other electronic components.

W415-1461 / D / 08.29.18

EN

W415-1461 / D / 08.29.18

4

1.1 DIMENSIONS

14"

356mm

24"

610mm

NEFI27H ILLUSTRATED

14"

356mm

NEFI24H ILLUSTRATED

27"

686mm

15 1/2"

393mm

14"

356mm

FRONT VIEW SIDE VIEW

EN

5

4.8B

A.

Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the

outlet are on.

B.

The appliance may emit a slight, harmless odour when ﬁ rst used. This odour is normal and it is caused

by the initial heating of internal appliance elements and will not occur again.

C.

If your appliance does not emit heat, consult the operation section of this manual for further

information.

D.

Use with a CSA- or UL-certiﬁ ed surge protector.

E.

Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured

homes when installed according to these instructions.

!

WARNING

READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO

FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE

IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL

ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT

SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR

RESULT IN A SAFETY HAZARD.

DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.

DO NOT USE DAMAGED ELECTRICAL CORDS.

SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE

POWER SUPPLY CIRCUIT.

TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF

RECEPTACLE AND FULLY INSERT.

1.2 LISTING APPROVALS

This log set has been tested in accordance with the

CSA Standards for ﬁxed and location-dedicated electric

room appliances in the United States and Canada. If

you need assistance during installation, please contact

your local dealer.

NOTE: This log set must be electrically wired and

grounded in accordance with local codes or, in the

absence of local codes, with National Electric Code

ANSI/NFPA 70-latest edition in the United States or

the Canadian Electric Code, CSA C22.1 in Canada.

Model Number

NEFI24H NEFI27H

Description

24" Electric

Logset Insert

27" Electric

Logset Insert

Voltage

120V AC 120V AC

Watts

Max 1500W Max 1500W

Amps

15 AMP Grounded

Circuit

15 AMP Ground-

ed Circuit

Appliance Width

24" (610mm) 27" (686mm)

Appliance Height

14"

(356mm)

15 1/2" (393mm)

Appliance Depth

14" (356mm) 14" (356mm)

Net Weight

25.4lbs (11.5kg) 29.5lbs (13.4kg)

Gross Weight

35.3lbs (16kg) 40.3lbs (18.3kg)

1.3 GENERAL INSTRUCTIONS

As with most electronic devices, your new log set has been designed to operate at temperatures between

5°C (41°F) and 35° C (95°F). During the colder winter months, allow the log set to reach room temperature

before turning it on.

EN

W415-1461 / D / 08.29.18

6

1.4 RATING PLATE INFORMATION

W385-2026 / A

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARD: CSA 22.2 NO. 46 AND UL 1278 /

HOMOLOGUÉ SELON LES NORMES NATIONALES CANADIENNES ET AMÉRICAINES:CSA 22.2 NO. 46 UL 1278

Page 1 of 1

FOYER À ÉLECTRIQUE. HOMOLOGUE POUR

INSTALLATION DANS UNE CHAMBRE A

COUCHER, UNE SALLE DE BAIN ET UN STUDIO.

APPROPRIE POUR INSTALLATION DANS UNE

MAISON MOBILE.

ELECTRIC FIREPLACE. SUITABLE FOR

BEDROOM AND BED-SITTING ROOM

INSTALLATION. SUITABLE FOR MOBILE

HOME INSTALLATION.

VOLTAGE: 120 VAC TENSION: 120VCA

FREQUENCY

: 60Hz FRÉQUENCE: 60Hz

POWER: 1500W PUISSANCE: 1500W

DATE CODE: XXXXX CODE DE DATE:

DESIGNED IN NORTH AMERCIA

BY WOLF STEEL LTD.

MADE IN CHINA

FABRIQUE EN CHINE

WOLF STEEL LTD.

24 NAPOLEON ROAD,

BARRIE, ON, L4M 0G8 CANADA

SERIAL NUMBER/NO. DE SERIE:

NEFI24

MATERIAL: CLASS IIIA-2 PERMANENT LEXAN ADHESIVE LABEL, MINIMUM THICKNESS 0.1MM, 121°C (250°F) RATING

SPECIFICATION: BLACK LETTERING ON WHITE BACKGROUND. MINIMUM FONT SIZE TO BE MINIMUM OF 8.5 PT (3.2mm)

MAX OVERALL SIZE: 6" x 3"

SERIAL NUMBERS TO BE ASCENDING FROM NEFI24 00601

TITLE: RATING PLATE NEFI24H

REVISION: A : REMOVED NEF127H, ADDED FRENCH || 06.01.15

DWG#: W385-2026

DATE: 03.23.15

DESIGN AMERIQUE DE NORD

PAR WOLF STEEL LTD.

MASTER CONTRACT: 161746

CONTRAT-CADRE: 161746

MODEL / MODÈLE:

NEFI24H

A

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to

the model of the appliance.

For rating plate location, see “LABEL LOCATION” section.

This illustration is for reference only. Refer to the rating plate on the log set for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

SAMPLE

1.5 LABEL LOCATION

GREEN

BLACK

WHITE

GREEN

BLACK

WHITE

CAUTION LABEL

(W385-1945)

"DO NOT COVER"

LABEL (W385-1946)

WARNING

LABEL

(W385-1943)

FRONT

RIGHT SIDE

LEFT SIDE

WARNING LABEL

(W385-1944)

RATING PLATE WITH

SERIAL NUMBER

NEFI24H (W385-2026)

NEFI27H (W385-2066)

NOTE: Do not use the log set during mobile home transportation.

ATTENTION

LABEL

(W385-2133)

EN

7

!

WARNING

2.0 LOCATING LOG SET

2.1 UNPACKING AND TESTING LOG SET

Carefully remove the appliance from the box and remove the support brackets. Prior to installing the

appliance, remove all packaging material and test to make sure the appliance operates properly by plugging

the power supply cord into a conveniently located 120V, 15 Amp minimum grounded outlet.

2.2 GROUNDING LOG SET

DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF

TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,

CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.

NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER

WATER CONTAINER.

WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND

MAINTENANCE.

TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE

MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED

OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.

DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)

96.1

GROUNDING METHODS

METAL SCREW

(A)

NOT ALLOWED IN CANADA

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

COVER OF

GROUNDED

OUTLET BOX

(C)

(B)

This appliance is for use on 120 volts. The cord has a plug

as shown in (A). An adapter as shown in (C) is available for

connecting three-blade grounding type plugs to two-slot

receptacles. The green grounding plug extending from the

adapter must be connected to a permanent ground such as

a properly grounded outlet box. The adapter should not be

used if a three-slot grounded receptacle is available.

To disconnect appliance, turn controls to off, then remove

plug from outlet.

NOTE: Must be connected to a dedicated 15 amp circuit.

The use of an extension cord is NOT permitted.

EN

W415-1461 / D / 08.29.18

8

3.0 INSTALLATION

NOTE: Follow all National and local electrical codes.

!

WARNING

RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID

TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN

CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD

AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.

RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT

USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.

RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.

THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.

USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE

WARRANTY AND/OR RESULT IN A SAFETY HAZARD.

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.

HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE

HAZARD.

DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.

68.5A

Do not install the log set

into a cavity smaller than

that referenced in the

table.

HEIGHT WIDTH DEPTH

LOG SET A B C

NEFI24H 15"

(381mm)

24"

(610mm)

14"

(356mm)

NEFI27H 16"

(406mm)

27 1/2"

(698mm)

14"

(356mm)

A

B

C

3.1 LOG SET INSTALLATION

The log set can be installed in any location. It is suggested to install the log set into an existing ﬁreplace or a

wood mantel for aesthetic purposes.

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high

trafﬁc areas.

3.1.1 INSTALLING LOG SET INTO EXISTING FIREPLACE

MINIMUM FIREPLACE CAVITY SIZE

The log set insert must be installed in an opening with the minimum cavity sizes shown below:

NOTE: Seal all chimney drafts with non-combustible materials to prevent any chimney debris from

falling onto the log set. Cap the top of the chimney ﬂue to prevent rain from entering.

Plug the log set into an outlet which has a 15Amp, 120V rating. If it is necessary to hard wire the log set see

"HARD WIRING INSTALLATION" section.

WARNING: Due to the high temperatures, do not use existing ﬁreplace doors which close or seal off

the log set. If installed behind any ﬁreplace door, allow heat to be exhausted. If using existing screens,

the screen must provide adequate airﬂow in front of the log set.

EN

9

Fig. 2

3.1.2 INSTALLING LOG SET INTO MANTEL

A. With two people, lift the log set up and insert into the opening. Do not push or slide the bottom of the

log set on the ﬂoor base, see Figure 1.

B. Set the log set down and into place, see Figure 2.

MANTEL

DO NOT SLIDE LOGSET

NE GLISSEZ PAS L'APPAREIL

!

MANTEL

STEP 1: LIFT

STEP 2: INSERT

STEP 3:

SET APPLIANCE

MANTEL

DO NOT SLIDE LOGSET

NE GLISSEZ PAS L'APPAREIL

!

MANTEL

STEP 1: LIFT

STEP 2: INSERT

STEP 3:

SET APPLIANCE

NOTE: To prevent damaging the base of the mantel, carefully lift the log set into the mantel while

avoiding contact with the front edge of the mantel base.

Fig. 1

NOTE: Leave enough

wire so that the log

set can be removed

from the enclosure

without disconnecting

the power supply.

A. Remove the securing screw from the electrical cover plate, located on the rear of the log set.

B. Add an electrical box connector and feed the supply wires through the 7/8" (22mm) hole.

C. Separate the black, white and green wires that have the wire nuts on them.

D. Remove the wire nuts and secure the black wire (power L1) to the black (power L1) lead of the

power supply. Connect the white wire from the unit to the white (neutral) wire from the power

supply. Connect the green wire to the ground wire.

E. Resecure the cover plate.

BLACK

WHITE

BLACK

WHITE

GREEN

GROUND

BLACK

WHITE

WIRE NUT

WALL

SWITCH

POWER

SUPPLY

MARRET

RED

GREEN

THERMOSTAT

(L1)

(N)

(G)

WIRE NUT

(L1)

(N)

(L1)

(N)

EN

W415-1461 / D / 08.29.18

10

GREEN

BLACK

WHITE

HARD WIRING CONNECTION

If it is necessary to hard wire, a qualiﬁed electrician must remove the cord connection, and wire directly to the

household wiring. The wire and power supply breaker must be rated for 120V and a minimum of 15 Amps.

This log set must be electrically connected and grounded in accordance with local codes, if hard wired. In

the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the

current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

NOTE: There are 3 wires from the ﬁreplace junction; white (neutral), black (power L1) and green

(ground) that connect to 120V power supply (breaker panel), see below.

White, Green and

Black wires:

Connect to 120V

power supply.

3.2 HARD WIRING INSTALLATION

NOTE: It is recommended to

secure the log set after hard

wiring, refer to "SECURING

THE LOG SET" section.

A. Place the log set in a position which provides optimum ﬂame performance. NOTE: To achieve ﬂame

effect, the log set should be set 1" away from the rear wall.

B. Secure in place using 2 screws (not supplied).

EN

11

3.3 SECURING THE LOG SET

NOTE: It is recommended to secure the log set especially if hard wiring the log set.

POWER

Turns the appliance ON/OFF.

FLAME & EMBER LIGHT

CONTROL

HEATER CONTROL

TIMER

TEMPERATURE

CONTROL

Controls Flame brightness and the Ember Light.

5 Settings

: Flame & Ember off (FO), Ember on but Flame

off (LL), small Flame & Ember (F1), medium Flame &

Ember (F2), brightest Flame and Ember (F3).

Default setting is (F3).

Turns the Heater and Blower ON/OFF.

4 Settings: Heater & Blower off (HO), Blower on (BL), low

heat (H1), high heat (H2).

Default setting is (HO).

Timer can be programed to run appliance for specific

lengths of time (30mins. minimum to 6hrs maximum).

Default setting is Timer de-select.

Press and hold the Timer button for 5 seconds. This

will change the button to Temperature Control, or vice

versa. There are 7 temperature settings (61

°F, 64°F, 70°

F,

75

°F, 81°F, 85°F and OFF).

Default setting is de-select Temperature Control.

F° / C° SWITCH

Hold 5

seconds

To change temperature format, Fahrenheit or Celsius.

Press and hold the Flame button for 5 seconds.

Default setting is Fahrenheit.

HEATER LOCK

Hold 5

seconds

Heater button can be locked or unlocked by holding the

Heater button for 5 seconds.

Default setting is heater unlock

Hold 5

seconds

EN

W415-1461 / D / 08.29.18

12

4.0 OPERATING INSTRUCTIONS

Once the log set has been plugged into a grounded electrical outlet or hard wired to a dedicated 120V power

supply, it is ready to operate.

ATTENTION: Ensure the house circuit breakers for the power supply are turned on. When initially

connecting the appliance into a power source the unit will perfom an LED check. The unit will ﬂash

on and off for 5 seconds.

The Control Panel is located on the front of the log set.

4.1 OPERATING CONTROL PANEL

EN

13

4.2 OPERATING BY REMOTE CONTROL

!

WARNING

TO AVOID DANGER OF SUFFOCATION KEEP THE PACKAGING BAG AWAY FROM BABIES AND

CHILDREN. DO NOT USE IN CRIBS, BED, CARRIAGES OR PLAY PENS. THIS BAG IS NOT A TOY.

KNOT BEFORE THROWING AWAY.

A. The power button can be used to turn the log set on/off. Pressing

this button activates the power to the log set. Pressing the

power button again will turn off the log set. The ember and log will

fade after 4 seconds after turning off the log set.

B. To adjust the ﬂame brightness and ember log light, press the ﬂame

button . There is one ember log light and three ﬂame brightness

levels to cycle through and then an off setting (LL, F1, F2, F3 and

then F0). F3 is the brightest ﬂame level, LL is the ember log light

only.

C. To control the thermostat function press the thermostat button .

There are 7 temperature settings (61°F, 64°F, 70°F, 75°F, 81°F 85°F

and off). The default setting will display Fahrenheit. Press the

thermostat button to cycle through the settings. Once you have

selected the desired temperature the heater will automatically

operate until that temperature is reached. When the room

temperature is 2 degrees lower than the temperature setting, the

heater will turn on.

D. To activate the heater and blower, press the heater button , the

blower will turn on. Press the heater button again to set desired low

or high heat temperature; press the heater button again to turn off

the heater.

E. The timer controls all operating modes of the log set. To activate the

timer, press the timer button , the icon will illuminate and the time

will appear on the LED display. To choose the desired time, continue to press the timer button, there

are 8 settings (30mins,1h, 2h, 3h, 4h, 5h, 6h and off). The ﬁreplace will turn off at the setting time.

F. To turn off the log set, press the power button once on the remote, or press the power button once on

the control panel on the unit.

NOTE: This hand held remote control must remain within 6 meters or 19 feet of the log set to be

effective.

NOTE: When operating the remote control, it must be directed towards the front center of the log set.

4.3 REMOTE BATTERY INSTALLATION

1. To replace the existing battery, remote the battery

holder.

2. To remove the battery holder, turn remote onto

front side and press the left side lever towards the

center while pulling the battery holder out using the

slot provided.

3. Replace existing battery, type CR 2025, with a

new battery and reinstall the battery holder into the

remote by sliding it into position, as shown.

4. Battery cover is secure onto the remote control

when a "CLICKING" noise is heard.

REMOTE

(REAR SIDE)

BATTERY (CR 2025)

BATTERY COVER

EN

W415-1461 / D / 08.29.18

14

5.0 FINISHING

!

WARNING

POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID

RECONSTRUCTION.

HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.

NEFI24H

NEFI27H

Place the log (#1) onto the pin.

Ensure the log is secure onto the

pin, as shown.

Place log (#2) onto the pin. Ensure

the log is secure onto the pin, as

shown.

Place the logs shown on the location

dimples on the burner platform.

Place the logs shown on the location

dimples on the burner platform.

#1

NEFI24H

NEFI27H

#2

NEFI24H

NEFI27H

#1

Place log (#1) onto the pin. Ensure the log

is secure onto the pin, as shown.

5.1 NEFI24H LOG PLACEMENT

5.2 NEFI27H LOG PLACEMENT

1

3

1 2

2

EN

15

Place log (#2) onto the pin. Ensure the log

is secure onto the pin, as shown.

Place log (#3) onto the pin. Ensure the log

is secure onto the pin, as shown.

NEFI24H

NEFI27H

#2

NEFI24H

NEFI27H

#3

5.3 EMBER BED PLACEMENT

Place the ember bed over the LED tray, as

shown.

3 4

EN

W415-1461 / D / 08.29.18

16

A. Place the charcoal ember around the front and sides of the ember bed, as indicated on the diagram

below.

NOTE: Do not block air intake opening and outlet with charcoal embers.

CHARCOAL

EMBERS

OUTLET

OPENING

AIR INTAKE

OPENING

BRAISES DE

CHARBON

L’OUVERTURE

D’AIR

L’OUVERTURE DU

VOLET D’AIR

5.4 CHARCOAL EMBER PLACEMENT

NEFI24H ILLUSTRATED

EN

17

6.0 WIRING DIAGRAM

!

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED

SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

PLUG /

FICHE

FAN /

SOUFFLERIE

MOTOR /

MOTEUR

AC-N

AC-L

RLY1 RLY2 RLY3 RLY4

NTC

OUTOUT

OUT

IN

#7

#8

#5

#6

#2 #4

#14

#1

#9

#3

#11

#12

#13

#10

#15

CARTE DE CIRCUIT IMPRIMÉ

MAIN PCB BOARD /

L

N

G

WIRE NUT /

CONNECTEUR

DE FILS

WIRE NUT /

CONNECTEUR

DE FILS

WIRE NUT /

CONNECTEUR

DE FILS

HEATER 700W2 /

CHAUFFERETTE 700W2

HEATER 700W1 /

CHAUFFERETTE 700W1

THERMAL CUT-OFF /

COUPURE

THERMIQUE

700W1

700W2

MOTOR /

MOTEUR

FAN /

SOUFFLERIE

T-FUSE /

FUSIBLE

FLAME /

FLAMME

DISPLAY CN3 /

AFFICHAGE

TEMPERATURE

SENSOR /

CAPTEUR DE

EMPÉRATURE

CONTROL PANEL BOARD /

PANNEAU DE CONTRÔLÉ

FLAME LED LIGHT /

LUMIÈRE DEL DE FLAMME

LOG LIGHT /

DEL DES BÛCHES

#1 EMBER BED LIGHT /

#1 LUMIÈRE LIT DE BRAISES

LOG LIGHT /

DEL DES BÛCHES

#2 EMBER BED LIGHT /

#2 LUMIÈRE LIT DE BRAISES

EN

W415-1461 / D / 08.29.18

18

41.1C

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts

can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE

REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

•

Model & Serial Number of appliance

•

Installation date of appliance

•

Part number

•

Description of part

•

Finish

PARTS, PART NUMBERS AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT NOTICE.

PARTS IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN 2 TO 5 BUSINESS DAYS FOR MOST

DELIVERY DESTINATIONS.

PARTS NOT IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN A 2 TO 4 WEEK PERIOD, FOR

MOST CASES.

PARTS IDENTIFIED AS ‘SO’ ARE SPECIAL ORDER AND CAN TAKE UP TO 90 DAYS FOR DELIVERY.

FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE

ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

** THIS IS A FAST ACTING THERMOCOUPLE. IT IS AN INTEGRAL SAFETY COMPONENT. REPLACE ONLY WITH

A FAST ACTING THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD.

!

WARNING

For after sales service, please call 1-866-820-8686

7.0 REPLACEMENT PARTS

EN

19

NOTE: Care must be taken when removing and disposing of any broken glass or damaged

components. Be sure to vacuum up any broken glass from inside the appliance before operation.

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

3

15

2216

13

14

1

2

3

25

5

6

39

3

10

3

11

3

12

23

22

24

7

8

4

NEFI24H 02.01.16

17

W135-0604

W135-0603

W135-0600

W135-0602

W135-0601

19

18

20

21

22

DESCRIPTIONPART NO.REF.

14

15

16

17

18

19

20

21

22

23

24

25

G660-0004

G750-0032

W010-3833-SER

W135-0604

W135-0601

W135-0603

W135-0600

W135-0602

W135-0610

W550-0013

G405-0011

G190-0005

DESCRIPTIONPART NO.REF.

1 W135-0605

2

3

4

5

6

7

8

9

10

11

12

13

W405-0023

W405-0025

G405-0012

W435-0059

W005-0019

W010-3617

W105-0020

G010-0081

G190-0006

G190-0004

G010-0079

G615-0002

EMBER BED, FRONT

EMBER BED LED

FLAME LED, NEFI24H

LOG LED

SYNCHRONOUS MOTOR

ADAPTOR

REFLECTOR, NEFI24H

BUSHING

CONTROL PANEL, NEFI24H

CONTROL PANEL BOARD

TEMPERATURE

SENSOR

BLOWER & HEATER ASSEMBLY

SPACER, 4PCS

MAIN PCB BOARD

REMOTE CONTROL TRANSMITTER

WIRE ASSEMBLY

LOG SERVICE PART KIT

, NEFI24H

TOP LEFT LOG

FRONT LEFT LOG

TOP RIGHT LOG

REAR LOG

EMBER BED, REAR

FRONT RIGHT LOG

CHARCOAL, EMBER

REAR EMBER LED

7.1 NEFI24H OVERVIEW

EN

W415-1461 / D / 08.29.18

20

17

3

15

2216

13

14

1

2

3

5

39

3

10

3

12

24

2225

6

7

8

4

26

NEFI27H 02.01.16

W135-0609

W135-0604

W135-0603

W135-0607

W135-0606

W135-0608

11

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

18

20

21

22

19

23

DESCRIPTION

REF.

PART NO.

DESCRIPTION

REF.

PART NO.

1

2

3

4

5

6

7

8

9

10

11

12

13

W135-0605

W405-0023

W405-0025

G405-0012

W435-0059

W005-0019

W010-3617

W105-0020

G010-0081

G190-0006

G190-0004

G010-0079

W615-0135

EMBER BED, FRONT

EMBER BED LED

FLAME LED, NEFI24H

LOG LED

SYNCHRONOUS MOTOR

ADAPTOR

REFLECTORTOR, NEFI27H

BUSHING

CONTROL PANEL, NEFI27H

CONTROL PANEL BOARD

TEMPERATURE SENSOR

BLOWER & HEATER ASSEMBLY

SPACER, 4 PCS

14

15

16

17

18

19

20

21

22

23

24

25

26

G190-0005

G660-0004

W750-0359

W010-3834-SER

W135-0610

G020-0014

G405-0011

EMBER BED, REAR

CHARCOAL, EMBER

REAR EMBER LED

MAIN PCB BOARD

REMOTE CONTROL TRANSMITTER

WIRE ASSEMBLY NEFI24H/NEFI27H

LOG SERVICE PART KIT, NEFI27H

TOP LEFT LOG

TOP CENTRE LOG

TOP RIGHT LOG

REAR LOG

FRONT RIGHT LOG

FRONT LEFT LOG

W135-0609

W135-0608

W135-0604

W135-0603

W135-0606

W135-0607

NOTE: Care must be taken when removing and disposing of any broken glass or damaged

components. Be sure to vacuum up any broken glass from inside the appliance before operation.

7.2 NEFI27H OVERVIEW

La page charge ...

NAPOLEON NEFI24H Le manuel du propriétaire

Ce manuel convient également à

NAPOLEON NEFI24H Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents