DeWalt DCN680B Manuel utilisateur

Marque: DeWalt

Modèle: DCN680B

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

DCN680D1

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCN680

20V MAX* Cordless 18GA Brad Nailer

Cloueuse de finition sans fil, calibre 18, 20V MAX*

Clavadora inalámbrica de calibre 18 de 20 V MÁX*

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 16

Español (traducido de las instrucciones originales) 31

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings

and allinstructions. Failure to follow the

warnings and instructions may result in

electric shock, fire and/or seriousinjury.

WARNING: To reduce the risk of injury, read

the instructionmanual.

If you have any questions or comments about

this or any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

Trigger

Trigger lock-off

Depth adjustment wheel

Headlights/Low battery/

Stallindicator

Jam clearing latch

Contact trip

Sliding magazine

Bump/Sequential

selectorswitch

Reversible belt hook

No-mar pad

No-mar pad storage

Stall release lever

Nail depth indicator

Battery

Battery release button

Magazine latch

Low nail indicator

Fig. A

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

ENGLISH

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from

the battery may cause irritation orburns.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

Nailer Safety Warnings

• Always assume that the tool contains fasteners.

Careless handling of the nailer can result in unexpected

firing of fasteners and personalinjury.

• Do not point the tool towards yourself or anyone

nearby. Unexpected triggering will discharge a fastener

causing aninjury.

• Do not actuate the tool unless the tool is placed

firmly against the workpiece. If the tool is not in

contact with the workpiece, the fastener may be deflected

away from yourtarget.

• Disconnect the tool from the power source when the

fastener jams in the tool. While removing a jammed

fastener, the tacker may be accidentally activated if it is

pluggedin.

• Do not use this nailer for fastening electrical cables.

It is not designed for electric cable installation and may

damage the insulation of electric cables thereby causing

electric shock or firehazards.

Additional Nailer Safety Warnings



WARNING: When using any nailer, all safety

precautions, as outlined below, should be followed

to avoid the risk of death or serious injury. Read and

understand all instructions before operating thetool.



WARNING: NEVER spray or in any other way apply

lubricants or cleaning solvents inside the tool. This can

seriously affect the life and performance of thetool.



WARNING: if the tool has been dropped or you

suspect tool damage perform tool operation check as

defined in the mode selection section of the manual. If

it doesn’t perform according to the manual, stop using

the tool and have it serviced at an authorized dewalt

service center.

• Hold tool by insulated gripping surfaces when

performing an operation where driven fastners may

contact hidden wiring. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock

theoperator.

• Actuating tool may result in flying debris, collation

material, or dust which could harm operator’s eyes.

Operator and others in work area MUST wear safety

glasses with side shields. These safety glasses must

conform to ANSI Z87.1 requirements (approved

glasses have “Z87” printed or stamped on them. It is

the employer’s responsibility to enforce the use of eye

protection equipment by the tool operator and other

people in the workarea.

• Always wear appropriate personal hearing and

other protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearingloss.

• Disconnect battery pack from the tool when not in use.

Always remove battery pack and remove fasteners from

magazine before leaving the area or passing the tool

to another operator. Do not carry tool to another work

area in which changing location involves the use of

scaffoldings, stairs, ladders, and the like, with battery

pack connected. Do not make adjustments, perform

maintenance or clear jammed fasteners while battery is

inplace.

• Do not remove, tamper with, or otherwise cause

the tool, trigger, trigger lock-off, or contact trip to

become inoperable. Do not tape or tie trigger or contact

trip in the ON position. Do not remove spring from contact

trip. Make daily inspections for free movement of trigger

and contact trip. Uncontrolled discharge couldresult.

• Inspect tool before use. Do not operate a tool if

any portion of the tool, trigger, trigger lock-off, or

contact trip is inoperable, disconnected, altered,

or not working properly. Damaged parts or missing

parts should be repaired or replaced before use. Refer

toRepairs.

• Do not alter or modify the tool in anyway.

• Always assume that the tool containsfasteners.

• Do not point the tool at co-workers or yourself at

any time. No horseplay! Work safe! Respect the tool as a

workingimplement.

• Keep bystanders, children, and visitors away while

operating a power tool. Distractions can cause you to lose

control. When tool is not in use, it should be locked in a

safe place, out of the reach ofchildren.

• Do not carry the tool from place to place holding the

trigger. Accidental discharge couldresult.

ENGLISH

• Always use trigger lock-off when tool is not in

immediate use. Using the trigger lock-off will prevent

accidentaldischarge.

• Do not overreach. Maintain proper footing and balance at

all times. Loss of balance may cause personalinjury.

• Use the tool only for its intended use. Do not

discharge fasteners into open air, concrete, stone,

extremely hard woods, knots or any material too

hard for the fastener to penetrate. Do not use the

body of the tool or top cap as a hammer. Discharged

fasteners may follow unexpected path and

causeinjury.

• Always keep fingers clear of contact trip to prevent

injury from inadvertent release of the Pusher

• Refer to the Maintenance and Repairs sections for

detailed information on the proper maintenance of

thetool.

• Always operate the tool in a clean, lighted area. Be sure

the work surface is clear of any debris and be careful not

to lose footing when working in elevated environments

such asrooftops.

• Do not drive fasteners near edge of material. The

workpiece may split causing the fastener to ricochet,

injuring you or a co-worker. Be aware that the nail

may follow the grain of the wood (shiner), causing it to

protrude unexpectedly from the side of the work material.

Drive the chisel point of the nail perpendicular to the grain

to reduce risk ofinjury.

• Do not drive nails onto the heads of other fasteners or with

the tool at too steep an angle. Personal injury from strong

recoil, jammed fasteners, or ricocheted nails mayresult.

• Keep hands and body parts clear of immediate work

area. Hold workpiece with clamps when necessary to

keep hands and body out of potential harm. Be sure the

workpiece is properly secured before pressing the nailer

against the material. The contact trip may cause the work

material to shiftunexpectedly.

• Do not use tool in the presence of flammable dust,

gases or fumes. The tool may produce a spark that could

ignite gases causing a fire. Driving a nail into another nail

may also cause aspark.

• Keep face and body parts away from back of the tool

cap when working in restricted areas. Sudden recoil

can result in impact to the body, especially when nailing

into hard or densematerial.

• Grip tool firmly to maintain control while allowing tool

to recoil away from work surface as fastener is driven. In

Bump mode if contact trip is allowed to recontact work

surface before trigger is released an unwanted fastener

will bedriven.

• Choice of triggering method is important. Check the

manual for triggeringoptions.

Sequential/Bump Selector Switch

Sequential Action

• When using the tool in sequential mode mode, do

not actuate the tool unless the tool is placed firmly

against the workpiece.

Bump Action

• When using the tool in bump action, be careful of

unin tentional double fires resulting from tool recoil.

Unwanted fasteners may be driven if the contact trip is

allowed to accidentally re-contact the work surface.

To Avoid Double Fires:

ʵ Do not engage the tool against the work surface with

a strong force.

ʵ Allow the tool to recoil fully after each actuation.

ʵ Use tool in sequential mode.

• When “bump” actuating the finish nailer, always

keep tool in control. Inaccurate placement of tool can

result in misdirected discharge of a fastener.

• Do not drive nails onto the heads of other fasteners.

Strong recoil, jammed fasteners, or ricocheted nails may

result.

• Be aware of material thickness when using nailer. A

protruding nail may cause injury.

• Depth adjustment: To reduce risk of serious injury

from accidental actuation when attempting to

adjust depth, ALWAYS;

ʵ Remove battery pack.

ʵ Engage trigger lock.

ʵ Avoid contact with trigger during adjustments

• Do not drive nails blindly into walls, floors or other

work areas. Fasteners driven into live electrical wires,

plumbing, or other types of obstructions can result

ininjury.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use tool while tired or under the influence of drugs,

alcohol, or medication. A moment of inattention

while operating power tools may result in serious

personalinjury.

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

ENGLISH

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

ENGLISH

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a shortcircuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use

andShipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to the

FLEXVOLT™ battery, the

battery is in Shipping Mode.

Strings of cells are electrically

disconnected within the pack resulting in three batteries

with a lower Watt hour (Wh) rating as compared to one

battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hourbatteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 battery implied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

ENGLISH

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center forrecycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting batterypack.

Fig. C

2. Insert the battery pack

14

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process hasstarted.

ENGLISH

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

15

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before

firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

DCB101

Charging

Fully Charged

Hot/Cold Pack Delay

Problem Pack or Charger

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132:

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

yellow light will turn off and the charger will resume the

chargingprocedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing to light or by displaying a problem pack or charger

blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fullycharged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaningsolutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack in an air temperature below +40°F

(+4.5°C), or above +104°F (+40°C). This is important

and will prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

ENGLISH

also charge a partially used pack whenever you desire

with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting toclean.

6. Do not freeze or immerse the charger in water or any

otherliquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat orcold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged beforeuse.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

Intended Use

Your cordless finish nailer has been designed for driving

nails into woodenworkpieces.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

Your cordless finish nailer is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

Tool Specifications

Firing Mode Selectable: Sequential or Bump

Voltage 20

Height 302 mm

Width 96 mm

Length 264 mm

Weight (without battery) 5.3 lbs

Magazine Angle Straight

Loading Capacity 110 nails

Nail Specifications

Straight Nail Lengths 5/8" - 2 1/8" (16 mm - 54 mm)

Shank Diameters 18 gauge

Nail Stick Angles Straight

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Belt Hook (Fig. B)

The cordless nailers include an integrated belt hook

9

and

can be attached to either side of the tool to accommodate

left- or right-handedusers.

If the hook is not desired at all, it can be removed from

thetool.

Fig. B

To Remove Belt Hook

1. Remove battery pack fromtool.

2. To switch the tool from right- to left-hand usage simply

remove the screw

18

from the opposite side of the tool

and reassemble on the otherside.

3. Replace batterypack.



WARNING: Remove nails from magazine before

making any adjustments or servicing this tool. Failure

to do so may result in seriousinjury.



WARNING: Disconnect battery pack from tool

before making any adjustments, changing

accessories, servicing, or moving the tool. Such

preventative safety measures reduce the risk of

starting the toolaccidentally.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Installing and Removing the Battery Pack

(Fig. C)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

14

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

15

and firmly pull the battery pack out of the tool

ENGLISH

handle. Insert it into the charger as described in the charger

section of thismanual.

Fig. C

Proper Hand Position (Fig. D)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Fig. D

Mode Selection



WARNING: Always wear proper eye [ANSI Z87.1

(CAN/CSA Z94.3)] and ANSI S12.6 (S3.19) hearing

protection when operatingtool.

The

DeWALT

cordless nailers are assembled in accordance

with the ANSI Standard SNT-101-2002.

The finish nailer is capable of firing nails using bump

actuation or sequential actuation. If you would like to

have the bump actuation mode disabled, have the tool

serviced by an authorized

DeWALT

service center. Before

operating this tool, look at the selector switch to determine

the actuation mode. Read all instructions before selecting

actuationmode.



WARNING: Keep fingers AWAY from trigger when not

driving nails to avoid accidental fastener discharge.

NEVER carry tool with finger on trigger. In bump

mode tool will drive a nail if contact trip is bumped

while trigger isdepressed.

Sequential Actuation (Fig. E)

Use sequential actuation mode for intermittent nailing

where very careful and accurate placement and depth

control is desired. The sequential actuation mode provides

the maximum delivery of power for driving the longestnails.

To operate the nailer in sequential actuation mode:

1. Slide the selector switch

2

to expose the singlenail

icon .

2. Fully depress nosepiece against the work surface (motor

will start).

3. Pull trigger (nail will drive into work surface).

4. Releasetrigger.

5. Lift nosepiece off worksurface.

6. Repeat steps 2 through 4 for nextapplication.

NOTICE: The contact trip needs to be depressed followed

by a trigger pull for each nail followed by a release of both

the contact trip and trigger after eachnail.

Fig. E

Bump action (Fig. E)

Bump action is intended for rapid nailing on flat, stationary

surfaces and typically most effective for applications that

require driving shorternails.

When the tool is set in the bump actuation mode, two

methods of tool operation are available: place actuation

and bumpactuation.

Slide the selector switch

8

to expose the triplenail

icon .

To operate the tool using the place actuation

method:



WARNING: A nail will be driven each time the

trigger is depressed as long as the contact trip

remainsdepressed.

1. Depress the contact trip against the worksurface.

2. Depress thetrigger.

To operate the tool using the bump actuation

method:

1. Depress thetrigger.

2. Push the contact trip against the work surface. As long

as the trigger is depressed, the tool will drive a nail every

time the contact trip is depressed. This allows the user

to drive multiple nails insequence.



WARNING: Do not keep trigger depressed when tool

is not in use. Keep the trigger lock-off in the locked

position when the tool is not inuse.



WARNING: When the tool’s motor is running, pulling

the trigger or depressing the contact trip will cause a

nail to bedriven.

Preparing the Tool



WARNING: NEVER spray or in any other way apply

lubricants or cleaning solvents inside the tool. This can

seriously affect the life and performance of thetool.

ENGLISH

NOTE: The battery pack is not fully charged out of the

carton. Follow instructions outlined (see Charging

a Battery).

1. Read the Safety Instruction section of thismanual.

2. Wear eye and earprotection.

3. Ensure magazine is empty of allfasteners.

4. Check for smooth and proper operation of contact

trip and pusher assemblies. Do not use tool if either

assembly is not functioning properly. NEVER use

a tool that has the contact trip restrained in the

actuatedposition.

5. Keep tool pointed away from yourself andothers.

6. Insert fully charged batterypack.

Using the Trigger Lock-off (Fig. F)



WARNING: To reduce the risk of serious personal

injury, do not keep trigger depressed when tool is not

in use. Keep the trigger lock-off switch LOCKED (Fig.F)

when the tool is not inuse.



WARNING: To reduce the risk of serious personal

injury, lock off trigger, disconnect battery pack

from tool and remove nails from magazine before

makingadjustments.

Each

DeWALT

nailer is equipped with a trigger lock-off

2

which when pushed to the right as shown in FigureF,

prevents the tool from firing a nail by locking the trigger and

bypassing power to themotor.

Fig. F

When the trigger lock-off is pressed to the left, the tool will

be fully operational. The trigger lock-off should always be

locked off whenever any adjustments are made or when

tool is not in immediateuse.

NOTICE: Do not store tool with battery pack installed. To

prevent damage to the pack and to ensure best battery

life, store battery packs out of the tool or charger in a cool,

drylocation.

Loading the Tool (Fig. G)



WARNING: Keep the tool pointed away from yourself

and others. Serious personal injury mayresult.



WARNING: Never load nails with the contact trip or

trigger activated. Personal injury mayresult.



WARNING: Always remove battery pack before

loading or unloading nails. Serious personal injury

mayresult.

1. Press magazine latch

16

and open sliding

magazine

7

fully.

2. Insert fasteners into the side of magazine; fasteners

should be loaded with chisel tip against front

of magazine.

3. Close sliding magazine until the magazine latch

clips snuggly.

Fig. G

Unloading The Tool



WARNING: The trigger lock-off should always be

locked off whenever any adjustments are made or

when tool is not inuse.

1. Press magazine latch

16

and open sliding

magazine

7

fully.

2. Tip the tool up until the nails slide freely out of the side

of the magazine. Close sliding magazinefully.

3. Open the jam clear door on the nosepiece to verify

there are no nailsremaining.

Dryfire Lock Out feature

Tool is equipped with a dryfire lock out feature to prevent

tool from cycling when there are no fasteners loaded. When

the low nail indicator

17

is visible, the tool is running low

on fasteners. If this happens, the tool will be locked out

and will not actuate until more nails are loaded. (Refer to

Loading the Tool)

Adjusting Depth (Fig. H)

The depth that the fastener is driven can be adjusted using

the depth adjustment wheel

3

on the side of thetool.



WARNING: To reduce risk of serious injury from

accidental actuation when attempting to adjust

depth, ALWAYS:

• Remove batterypack.

• Engage trigger lock-off.

• Avoid contact with trigger duringadjustments.

1. To drive the nail shallower , rotate the depth

adjustment wheel

3

away from the nose of thenailer.

2. To sink a nail deeper , rotate the depth adjustment

wheel

3

toward the nose of thenailer.

ENGLISH

Fig. H

Headlights (Fig. I)

There is a headlight

4

located on each side of the nailer.

Headlights turn on upon battery insertion, activation of

the trigger, or depressing the contact trip. The lights will

automatically shut off after 20 seconds unless tool remains

inuse.

Fig. I

NOTE: These headlights are for lighting the immediate work

surface and are not intended to be used asflashlights.

LOW BATTERY INDICATOR: The left-side headlight will

flash four consecutive times and then shut down to indicate

lowbattery.

JAMMED NAIL INDICATOR: The right-side headlight will

flash continually if a nail becomes jammed in the nosepiece

(see Clearing a Jammed Nail).

Clearing a Jammed Nail (Fig. A, J)

If a nail becomes jammed in the nosepiece, keep the tool

pointed away from you and follow these instructions

toclear:

1. Remove battery pack from tool and engage the trigger

lock-off.

2. Press the magazine latch

16

and remove any

loadednails.

3. Lift the jam clear latch

5

then pull up to open the

nosepiecedoor.

4. Remove bent nail, using pliers ifnecessary.

5. If driver blade is in the down position, cycle the stall

release lever

12

using enough force to fully slide it to

the other end of the slot in thehousings.

6. Close the nosepiece door and engage the latch pin

under the two arms on the nosepiece. Push latch until

it locks inplace.

7. Reinsert batterypack.

NOTE: The tool will disable itself and not reset until the

battery pack has been removed andreinserted.

8. Reinsert nails into magazine (see Loading the Tool).

Fig. J

NOTE: Should nails continue to jam frequently in nosepiece,

have tool serviced by an authorized

WALT servicecenter.

Cold Weather Operation

When operating tools at temperatures below freezing:

1. Keep tool as warm as possible prior touse.

2. Actuate the tool 5 or 6 times into scrap lumber

beforeusing.

Hot Weather Operation

Tool should operate normally. However, keep tool out of

direct sunlight as excessive heat can deteriorate bumpers

and other rubber parts resulting in increasedmaintenance.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

ENGLISH

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Accessories



WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

DeWALT

Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-

DeWALT

(1-800-433-9258) or visit our website:

www.dewalt.com.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a

DeWALT

factory

service center or a

DeWALT

authorized service center.

Always use identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from the

date of purchase. This warranty does not cover part failure

due to normal wear or tool abuse. For further detail of

warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-

DeWALT

(1-800-433-9258).

This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and

you may have other rights which vary in certain states

orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB606

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

ENGLISH

Troubleshooting Guide

MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT

PROBLEMS, CONTACT A

DeWALT

SERVICE CENTER OR CALL 1-(800)-4-

DeWALT



WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before

making any adjustments or removing/installing attachments or accessories. An accidental start-up can

causeinjury.

Symptom Cause Fix

Tool doesn’t turn on

(Headlights don’t turn on)

Tool internal electronics not reset Remove battery, wait 3 seconds and reinsert

Low battery charge or damaged battery Charge or replace battery

Terminals are dirty or damaged See authorized service center

Bent contact trip See authorized service center

Damaged internal electronics See authorized service center

Tool doesn’t actuate (Headlights on,

motor does not run)

Motor stops running after 4 seconds Normal operation; release trigger or contact trip and

redepress

Contact trip or trigger not depressed See instruction manual

Damaged trigger See authorized service center

Bent contact trip See authorized service center

Damaged internal electronics See authorized service center

Tool in sequential mode and only trigger being actuated. Change mode or depress contact trip in

sequential mode.

Tool doesn’t actuate (Left headlight

flashes 4 times)

Low battery charge or damaged battery Charge or replace battery

Tool doesn’t actuate (Right headlights

flashes continuously)

Jammed fastener Remove the battery, clear the jammed fastener, (push

driver blade back using the stall release lever) and

reinsert battery pack

Jammed mechanism See authorized service center

Tool doesn’t actuate (Headlights on,

motor runs)

Damaged internal electronics See authorized service center

Tool doesn’t actuate (Headlights on,

motor runs, driver blade stuck down)

Damaged return system Replace return system; see authorized service center

Debris in nosepiece Clean nosepiece

Damaged driver/return assembly Replace driver/return assembly; see authorized service

center

Tool operates, but does not drive the

fastener fully

Low battery charge or damaged battery Charge or replace battery

Depth adjustment set too shallow Rotate depth adjustment wheel to a deeper setting

Tool not firmly applied to workpiece See instruction manual

Material and fastener length too rigorous an application Choose appropriate material or fastener length

Damaged or worn driver blade tip Replace driver/return assembly; see authorized service

center

Damaged or worn driver/return assembly Replace driver/return assembly; see authorized service

center

Tool operates, but no fastener driven No fasteners in magazine Load fasteners into magazine

Wrong size or angle fasteners Use only recommended fasteners

Debris in nosepiece Clean nosepiece

Debris in magazine Clean magazine

Worn magazine Replace magazine; see authorized service center

Damaged or worn driver blade Replace driver/return assembly; see authorized service

center

Damaged pusher spring Replace spring; see authorized service center

ENGLISH

Symptom Cause Fix

Tool is locked out, but no

fastener driven

Tool is equipped with a dryfire lock out feature to prevent

tool from firing when there are no fasteners loaded. When

the low nail indicator is visible, the tool is running low

on fasteners.

Load fasteners into magazine

Jammed fastener Wrong size or angle fasteners Use only recommended fasteners

Damaged or worn driver blade Replace driver/return assembly; see authorized

service center

Material and fastener length too rigorous an application Material or fastener length inappropriate

Low battery charge or damaged battery Charge or replace battery

Debris in nosepiece Clean nosepiece

Debris in magazine Clean magazine

Worn magazine Replace magazine; see authorized service center

Worn or damaged pusher spring Replace spring; see authorized service center

FRANÇAIS

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.



AVERTISSEMENT! lire tous les avertissements

de sécurité et toutes lesdirectives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Pour toute question ou remarque au sujet de cet outil

ou de tout autre outil

DeWALT

, composez le numéro

sans frais : 1-800-4-

DeWALT

(1-800-433-9258).

Gâchette

Verrouillage de gâchette

Molette de réglage de

profondeur

Système d’éclairage/

voyant de charge/

enrayage

Dispositif de

désenrayage

Déclencheur par contact

Magasin à glissière

Sélecteur de tir sur

contact/séquentiel

Crochet de ceinture

réversible

Patin anti-rayures

Espace de rangement du

patin anti-rayures

Levier de désenrayage

Index de profondeur

de clou

Bloc-piles

Bouton de libération du

bloc-piles

Verrou du magasin

Voyant faible quantité

de clous

Français (traduction de la notice d’instructions originale)

Fig. A

FRANÇAIS

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

POUR LES OUTILS ÉLECTRIQUES



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise à

l’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc électrique est plus élevé si votre corps

est mis à laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive.

Ne jamais utiliser le cordon pour transporter,

tirer ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à

l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue

pour l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique

est utilisé. Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence de drogues,

d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut

entraîner des blessures corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source

d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter

un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de

provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les

situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

4) Utilisation et entretien d’un outil

électrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

FRANÇAIS

b ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et

doit êtreréparé.

c ) Débrancher la fiche de la source d’alimentation

et/ou du bloc-piles de l’outil électrique avant de

faire tout réglage ou changement d’accessoire

ou avant de ranger l’outil. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

e ) Entretien des outils électriques. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus

faciles àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les

forets, etc. conformément aux présentes

directives en tenant compte des conditions de

travail et du travail à effectuer. L’utilisation d’un

outil électrique pour toute opération autre que celle

pour laquelle il a été conçu estdangereuse.

5) Utilisation et entretien du bloc-piles

a ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc-piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de b loc-piles.

b ) Utiliser les outils électriques uniquement avec

les blocs-piles conçus à cet effet. L’utilisation de

tout autre bloc-piles risque de causer des blessures ou

unincendie.

c ) Lorsque le bloc-piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court-circuit des bornes du bloc-piles

risque de provoquer des brûlures ou unincendie.

d ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc-piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc-piles peut provoquer

des irritations ou desbrûlures.

6) Réparation

a ) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de

rechange identiques. Cela permettra de maintenir

une utilisation sécuritaire de l’outilélectrique.

Consignes de sécurité propres aux

cloueurs

• Assumer systématiquement que l’outil est chargé.

L’utilisation hasardeuse du cloueur pourra provoquer le tir

accidentel d’attaches et causer des dommagescorporels.

• Ne jamais pointer l’outil vers soi-même ou toute

autre personne à proximité. Le déclenchement

accidentel d’attaches causerait des dommagescorporels.

• Ne pas utiliser l’outil à moins qu’il ne soit appliqué

fermement contre la pièce à travailler. Dans le cas

contraire, l’attache pourrait être détournée de sacible.

• Déconnecter l’outil de sa source de courant

lorsqu’une attache est restée coincée dans l’outil.

Alors que l’on tente de retirer une attache bloquée, le

marteau pourrait être activé accidentellement si l’outil

restaitbranché.

• Ne pas utiliser cet outil pour fixer des câbles

électriques. Il n’a pas été conçu pour installer des câbles

électriques et pourrait en endommager l’isolant et poser

ainsi des risques de chocs électriques et d’incendies.

Consignes de sécurité additionnelles

propres aux cloueurs



AVERTISSEMENT: lors de l’utilisation de toute

cloueuse, toutes les directives de sécurité, énoncées

ci-après, doivent être respectées pour éviter tout risque

de fatalité ou de dommages corporels graves. Lire

et comprendre toutes ces directives avant d’utiliser

cetoutil.



AVERTISSEMENT: NE JAMAIS vaporiser, ou

appliquer de toute autre façon, aucun lubrifiant

ou solvant de nettoyage dans l’outil. Cela pourrait

affecter sérieusement la durée de vie et les

performances de l’outil.



AVERTISSEMENT : si l’outil est tombé, ou si l'on

soupçonne qu'il est endommagé, effectuer sa

vérification, comme expliqué dans la section selection

du mode du guide d'utilisation. Si l’outil ne fonctionne

pas conformément au guide d'utilisation, arrêter son

utilisation et le faire vérifier auprès d’un centre de

reparation agréé dewalt.

• Tenir l’outil par sa surface de prise isolée dans une

situation où l’outil de coupe peut entrer en contact

avec un câblage dissimulé. Tout contact avec un

fil « sous tension » mettra « sous tension » les pièces

métalliques exposées de l’outil et électrocutera l’opérateur.

• L’outil actionné pourrait projeter des débris, de la colle

d’assemblage ou de la poussière, qui peuvent tous

provoquer des lésions oculaires à l’opérateur. L’opérateur

et les autres personnes œuvrant dans la zone de travail

DOIVENT porter des lunettes de sécurité munies de

• (Fig. A)

La page charge ...

DeWalt DCN680B Manuel utilisateur

Marque: DeWalt

Modèle: DCN680B

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

DCN680D1

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCN680B User manual
español: DeWalt DCN680B Manual de usuario

DeWalt DCN680B Manuel utilisateur

Ce manuel convient également à

DeWalt DCN680B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents