VTech ErisStation VCS752 Manuel utilisateur

User’s manual

Model: VCS754

BC

Wireless Conference System

ErisStation

TM

businessphones.vtech.com

SIP Conference Phone with Wireless Mics

Congratulations

on purchasing your new VTech product. Before using this product, please read

Important safety instructions on page ii of this manual.

This manual includes the information and procedures necessary to install and

operate your new VTech product. Please review this manual thoroughly to ensure

proper installation and operation of this innovative and feature rich VTech product.

For support, shopping, and everything new at VTech, visit our website at

http://businessphones.vtech.com.

ErisStation

TM

and Orbitlink Wireless Technology

TM

are trademarks of VTech Communications, Inc.

When using your ErisStation Conference Phone with Wireless Mics, basic safety precautions should

always be followed to reduce the risk of re, electric shock and injury to persons, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a

damp cloth for cleaning.

4. Do not use this product near water such as near a bathtub, wash bowl, kitchen sink, laundry tub or

swimming pool, or in a wet basement or shower.

5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

6. Slots and openings in the back or bottom of the base unit and wireless mic are provided for ventilation.

To protect them from overheating, these openings must not be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or

heat register. This product should not be placed in any area where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on the marking label. If you

are not sure of the type of power supply in your ofce, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be

walked on.

9. Never push objects of any kind into this product through the slots in the base unit or wireless mic

because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any

kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized

service facility. Opening or removing parts of the base unit or wireless mic other than specied access

doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause

electric shock when the product is subsequently used.

11. Do not overload wall outlets and extension cords.

12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the

following conditions:

13. When the power supply cord or plug is damaged or frayed.

14. If liquid has been spilled onto the product.

15. If the product has been exposed to rain or water.

16. If the product does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operation instructions. Improper adjustment of other controls may

result in damage and often requires extensive work by an authorized technician to restore the

product to normal operation.

17. If the product has been dropped and the base unit and/or wireless mic has been damaged.

18. If the product exhibits a distinct change in performance.

19. Avoid using the ErisStation Conference Phone with Wireless Mics during an electrical storm. There is

a remote risk of electric shock from lightning.

20. Do not use the ErisStation Conference Phone with Wireless Mics to report a gas leak in the vicinity

of the leak. Under certain circumstances, a spark may be created when the adapter is plugged

into the power outlet, or when the wireless mic is replaced in its cradle. This is a common event

associated with the closing of any electrical circuit. The user should not plug the phone into a power

outlet, and should not put a charged wireless mic onto the charging cradle, if the phone is located

in an environment containing concentrations of ammable or ame-supporting gases, unless there

is adequate ventilation. A spark in such an environment could create a re or explosion. Such

environments might include: medical use of oxygen without adequate ventilation; industrial gases

(cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.

21. Only put the wireless mic next to your mouth when it is in normal talk mode.

22. The power cables are intended to be correctly oriented in a vertical or oor mount position. The

prongs are not designed to hold the plug in place if it is plugged into a ceiling or cabinet outlet.

23. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily

accessible.

24. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a

Important safety instructions

ii

wrong type of battery is used. Use only the supplied rechargeable battery or replacement battery

pack (BT191665/BT291665). Do not dispose of batteries in a re. They may explode. Dispose of

used battery according to the information in The RBRC

®

seal.

25. Use only the adapter included with this product. Incorrect adapter polarity or voltage can seriously

damage the product. Base unit power adapter: Input 100–240V AC 50/60Hz; Output: 9V DC 1500mA.

SAVE THESE INSTRUCTIONS

iii

Table of contents

Introduction ................................. 1

About ErisStation Conference Phone

with Wireless Mics .............................1

Parts checklist ........................................1

Getting Started ............................ 2

Connect base unit ..................................2

Install the wireless mic battery ..............3

Before use .............................................. 4

Base unit overview (front) ......................5

Base unit overview (rear) ....................... 7

Wireless mic overview ...........................8

Status indicators overview ..................... 9

Idle screen.............................................10

Idle mode screen icons .........................10

Active call screen icons ........................10

Using the phone menu .........................11

Main menu items ..................................11

Making calls ..........................................12

Conference phone operation .... 12

Use a wireless mic during a call ...........13

Ending the call ......................................13

Answering a call .................................... 13

Putting a call on hold ............................14

Forwarding calls .................................... 15

Transferring calls ..................................16

Making a conference call ...................... 18

Setting up a Network Conference ........19

Retrieving messages ............................19

Redialing ...............................................20

Muting active calls ................................20

Temporarily silencing the ringer ............20

Locating wireless microphones ............21

Using the conference phone as a PC

speakerphone ..................................21

Phone Features.......................... 22

Using the Features menu .....................22

Using the Call menu .............................23

Using the local directory .......................27

Call history ............................................30

Using Speed Dial ..................................33

Entering speed dial numbers ...............33

Conguring the Phone .............. 34

How to congure the phone .................34

Using the User Settings menu .............34

Preferences ........................................... 35

Setting the language ............................. 35

Setting date and time preferences .......36

Display ..................................................37

Audio .....................................................38

Wireless Mic Registration ......... 40

WebUI ......................................... 41

Using the WebUI ...................................41

Status ....................................................42

Call Settings ..........................................43

User Preferences ..................................45

Speed Dial ............................................47

Directory ................................................48

User Password .....................................51

Appendix .................................... 52

Battery ...................................................52

Troubleshooting ........................ 53

Finding the software version ................53

Precautions for users

of implanted cardiac

pacemakers ................................ 58

Table of contents

About wireless mics .................. 58

Maintenance ............................... 59

FCC, ACTA and IC

regulations ................................. 60

The RBRC

®

seal ......................... 61

California Energy Commission

battery charging testing

instructions ................................ 62

For C-ETL compliance only ...... 62

Mesures de sécurité

importantes ................................ 62

Limited warranty ........................ 65

Technical specications ........... 67

1

Introduction

Ethernet cable

Battery ×4

User’s manual Wireless mic ×4

Base unit

DC power cable

(with yellow plugs)

About ErisStation Conference Phone with Wireless Mics

The ErisStation Conference Phone with Wireless Mics is designed for use in ofce

settings. It consists of a base unit and four wireless mics, enabling participants in

different areas of a meeting room to deliver clear conversation in a phone conference.

Parts checklist

Your conference phone package contains the following items. Save your sales

receipt and original packaging in the event warranty service is necessary.

AC power cord

Power adapter

To purchase any accessories or replacements, visit our website at http://businessphones.vtech.com

or call 1-888-370-2006.

Battery door ×4

U

s

e

r

’

s

m

a

n

u

a

l

Quick start guide

(x4)

U

s

e

r

’

s

m

a

n

u

a

l

Quick start guide

(x4)

Li-ion Polymer batteries.

Phone line cord connector cable

Adapter Connection box

Power Line

VCS754

ETHERNT CABLE

User’s manual

Model: VCS754

businessphones.vtech.com

SIP Conference Phone with Wireless Mics

Quick Start Guide

Model: VCS754

businessphones.vtech.com

SIP Conference Phone with Wireless Mics

Quick start guide

USB cable

2

Connect base unit

Connect the base unit as shown below.

• The ErisStation Conference Phone with Wireless Mics requires connection to AC power to

operate.

• The supplied power adapter is designed for use with only the ErisStation Conference

Phone with Wireless Mics. It is not PoE compatible and is not designed to power any

network devices. Do not connect the supplied power adapter to any other network devices

through the supplied DC power cable or any other Cat5e ethernet cable.

• Connect the base unit only with the supplied DC power cable with yellow plugs. This cable

has a shielded interface and ferrite added for optimal performance.

• The ErisStation Conference Phone with Wireless Mics requires a network connection

to an IP PBX to operate. This manual assumes that your network infrastructure is

established and that your IP PBX phone service has been ordered and congured for

your location. For more information about installation options and phone setup, see the

VCS754 Administrator and Provisioning Manual, available at

http://businessphones.vtech.com.

• When

the base unit is powered up, the status indicators turn green for about two seconds.

• The AC power cord is intended for a vertical or oor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a ceiling or cabinet outlet.

1. Plug one end of the DC power cable into the power jack of the base unit, and

plug the other end into the VCS754 jack of the power adapter. Route the cord

through the slots.

2. Plug one end of the Ethernet cable into the LAN jack of the power adapter, and

plug the other end into a network switch or router.

3. Plug the small end of the AC power cord into the power jack of the adapter, and

plug the large end into a wall outlet not controlled by a switch.

4. Optional: Plug the mini-USB end of the USB cable to the base unit. Connect the other

end of the USB cable to a PC (to use PC speakerphone mode).

Network switch

or router

1

LAN

VCS754

2

3

E

Wall outlet

DC power cable

(with yellow plugs)

Ethernet cable

AC power cord

Adapter

Slots

4

Getting Started

3

Install the wireless mic battery

1. Place the battery (with the label THIS SIDE UP facing up) into the battery

compartment.

2. Slide the battery door until it clicks into place.

Note: The status indicator on the wireless mic turns orange when charging, and turns

off when the wireless mic is fully charged.

3. Place the wireless mic onto the charging cradle until it is ush.

Getting Started

4

Before use

Check for dial tone

Lift all the wireless mics from the charging cradles, and then put them on the table.

After that, press

. If you hear a dial tone, and see that the status indicators turn

green on both the base unit and the wireless mics, the installation is successful.

If you do not hear a dial tone:

• Recheck the installation diagram and the connections to the unit.

• Ensure the unit is correctly congured with the correct SIP account information.

For more information, see the VCS754 Administrator and Provisioning Guide,

available at http://businessphones.vtech.com.

• Consult your service provider if you require additional user accounts or if you

suspect a service disruption is at fault.

Operating range

This conference phone operates with the maximum power allowed by the Federal

Communications Commission (FCC). Even so, this wireless mic and base unit can

communicate over a certain distance, which can vary with the locations of the base

unit and wireless mic, the weather, and the layout of your ofce.

When the wireless mic is out of range, the status indicator ashes red quickly on

the wireless mic. The wireless mic will sleep after being out of range for 30 minutes.

Therefore, you should always return the wireless mic to the charging cradle after use.

If there is an incoming call while the wireless mic is out of range, the incoming call

green light may not ash on the wireless mic. If it ashes, the call may not connect

well when you press

on the base unit. Move the wireless mic closer to the base

unit, and then press on the base unit to answer the call. If the wireless mic moves

out of range during a telephone conversation, there may be interference. To improve

reception, move closer to the base unit.

Getting Started

5

Base unit overview (front)

a

n

b

c

e

d

f

g

h

i

j

k

l

m

1. Speaker

2. LCD screen

3. Status indicator

• Indicates the system status. See also Status indicators overview on page 9.

4. MENU / SELECT

• Press to show the menu.

• Press to select an item, or save an entry or setting in a menu.

5. Navigation keys p q / t u

• Press to scroll up or down while in the menu, phonebook, or call log.

• Press to move the cursor right or left while entering names or numbers.

• Press to view additional soft key labels and view multiple active calls.

Getting Started

6

6.

• Press to make, answer, or end a call.

7. Dial pad keys

• Press to enter numbers or characters.

• While editing names, press

to add a space.

8. Front microphone

9. MUTE ALL

• During a call, press to mute or end mute all microphones in the system.

10.

/

• Press to adjust the ringer volume.

• During a call, press to adjust the listening volume.

11. Soft keys

• Press to perform actions as indicated by the on-screen labels.

12. Wireless mic

• See Wireless mic overview on page 8.

13. Charging contacts

14. HOLD / CANCEL

• While on a call, press HOLD to put the call on hold.

• While in a menu, press CANCEL to return to the previous menu.

Getting Started

7

Base unit overview (rear)

1. Status indicator

• Indicates the system status. See also Status indicators overview on page 9.

2. Rear microphone

3. USB port

• For connecting a PC to use the PC speakerphone feature. See page 21.

4. Adapter jack

a

b

c

d

Getting Started

8

Wireless mic overview

1. Microphone

• Functions as an extended microphone of the base unit during a call.

2. Status indicator

• Indicates the system status. See Status indicators overview on page 9.

3. MUTE ALL

• During a call, press to mute or end mute all microphones in the system.

4. Battery door

5. Charging contacts

1

2

3

4

5

Getting Started

9

Status indicators overview

Status indicator on the base unit

Power up • Green for about two seconds.

On a call • Green during a call.

• Red when the system is muted during a call.

Call on hold • Flash green slowly.

Incoming call • Flash green when there is an incoming call.

Status indicator on the wireless mic

Power up • Orange for about two seconds.

On the cradle • Orange when charging on the cradle except during registration.

• Flashes red and green alternately when the non-registered

wireless mic is charging on the cradle.

Off the cradle • Green during a call.

• Red when the system is muted during a call.

• Off when the wireless mic is in idle mode or without a battery.

• Flashes orange when the wireless mic’s battery is low.

• Flashes green when there is an incoming call.

• Flashes red slowly when the wireless mic is:

• out of range; or

• not registered; or

• off cradle during paging (with a paging tone).

During

registration

• Flashes red and green alternately.

Getting Started

10

Idle screen

The Idle screen appears after the phone is connected and congured for your SIP

PBX service. The Idle screen indicates that you have no active or held calls.

From the Idle screen, you can press:

•

Directory

to view the directories that are available to you. See Using the local

directory on page 27.

•

Line

to select another line (SIP Account). When you make a call, the phone

will use this line. Note:

Line

appears only if more than one SIP account is

registered to your phone.

•

PC SPK

to use the VCS754 as a speakerphone for calls made on the connected

PC (using a softphone or messaging application). See page 21.

•

Call Log

to view the phone’s call history. See Call history on page 30.

Note that the default Idle screen soft keys are shown above. Your phone’s soft keys

are programmable and may differ from what is shown here.

Idle mode screen icons

In idle mode, the following screen icons indicate your phone’s current settings.

Icon Status

Call Forward All is on. See To set Call forward: on page 24.

The ringer is off.

Do Not Disturb is on. See To set Do Not Disturb: on page 24.

Active call screen icons

During a call, the following screen icons indicate the call’s status.

Icon Status

Speakerphone—the speakerphone is active.

1/2

Call counter—more than one call is active.

More than one call is active. Press q or p to view another call.

Getting Started

11

Using the phone menu

1. Press MENU to show the main menu.

2. Press q or p to highlight menu items.

3. Press SELECT or a corresponding dial pad key to select a highlighted menu

item. For example, when Features is highlighted, you can press SELECT or you

can press 1 on the dial pad to view the Features submenu.

4. Press SELECT or an appropriate soft key to save changes.

5. Press CANCEL to cancel an operation, exit the menu display or return to the idle

screen.

Main menu items

1. Features (see page 22)

2. Status (see page 53)

3. User settings (see page 34)

4. Admin settings (available only to your system administrator)

Getting Started

12

Making calls

You can make a call at any time by pressing

, and then dialing a number. When

the phone is in idle mode or has calls on hold, you can make a call by pre-dialing a

phone number and then pressing

or

Dial

to call the number.

To make a call:

1. Press

. You hear a dial tone.

2. Use the dial pad keys to enter the desired phone number.

• Press

Backspc

if you enter an incorrect digit.

• Press

123

to change from entering digits to entering letters (if you need

to enter a domain name as part of the number). When entering letters,

pressing the * or # keys allows you to enter symbols. For example, press *

twice for the @ symbol.

3. Press

Dial

, or, if the number as valid, the phone dials the number after a

short delay.

Note that the default live dial soft keys are shown above. Your phone’s soft keys are

programmable and may differ from what is shown here.

To make a call by pre-dialing:

1. Use the dial pad keys to enter the desired phone number.

• Press

Backspc

if you enter an incorrect digit.

• Press

123

to change from entering digits to entering letters (if you need

to enter a domain name as part of the number). When entering letters,

pressing the * or # keys allows you to enter symbols. For example, press *

twice for the @ symbol.

2. Dial the number by pressing

or

Dial

:

Conference phone operation

13

When the call is answered, the active call screen appears.

Note that the default active call screen soft keys are shown above. Your phone’s soft

keys are programmable and may differ from what is shown here.

Use a wireless mic during a call

1. During a call, lift a wireless mic from the base unit charging cradle, and then put

it on the table. The status indicator on the wireless mic turns green.

2. Speak towards the microphone on the wireless mic.

• For best performance, speak to the microphone on the wireless mic at a

distance of no more than 3 feet.

• Always return the wireless mics to the charging cradles after use.

Ending the call

To end the call, press

or

End

.

Answering a call

To answer a call:

On the base unit, press

, or press

Answer

.

• If you have multiple incoming calls, (as indicated by ), press q or p to select

the call you want to answer.

On the incoming call screen, you can also press:

•

Reject

to terminate the incoming call.

•

Forward

to forward the call to another number.

If you don’t respond to an incoming call, the phone displays a missed-call alert screen.

Conference phone operation

14

If a missed call alert screen appears, you can press:

•

Exit

to return to the Idle screen.

•

Callback

to immediately dial the caller’s number.

•

View

to see the caller’s information in the call history.

Putting a call on hold

Use this feature to hold one call while you access another. The phone also puts

calls on hold automatically when you answer another call, transfer a call, or create a

conference.

To put a call on hold:

During a call, press HOLD on the base unit.

The On hold screen appears. The status indicators ash green slowly.

From the On hold screen, you can press:

•

End

to end the call

•

New

to dial a new call

•

Resume

to take the call off hold.

•

Transfer

to transfer the held call to another party.

•

Conf

to start a conference with the held call.

Note that the default On hold screen soft keys are shown above. Your phone’s soft

keys are programmable and may differ from what is shown here.

If another party puts you on hold, you may see the message Held by far end. This

message depends on compatibility between phones and PBX types, and may not

always appear. You can press

End

to end the call.

Conference phone operation

La page charge ...

VTech ErisStation VCS752 Manuel utilisateur

Ce manuel convient également à

VTech ErisStation VCS752 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents