Jenn-Air TC507 Manuel utilisateur

Marque: Jenn-Air

Modèle: TC507

Catégorie: Compacteur de déchets

Taper: Manuel utilisateur

TC507

Use& CareGuide

For assistance, call: 1-800-688-1100.

Guide d'utilisation

et d'enITetien

Pour assistance, composer le 1-800-688-1100.

Table of Contents/Table des matieres ............. 2

JENN-AIR

9871894

TABLEOF CONTENTS TABLEDESMATIERES

COMPACTOR SAFETY .................................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Undercounter Installation ............................................................. 6

Air Freshener ................................................................................ 7

Changing the Decorative Panel ................................................... 7

COMPACTOR USE......................................................................... 9

How Your Compactor Works ....................................................... 9

Loading ......................................................................................... 9

StarLing Your Compactor ........................................................... 10

Stopping Your Compactor ......................................................... 10

Removing a Filled Bag ............................................................... 10

Installing a New Bag .................................................................. 11

COMPACTOR CARE .................................................................... 11

Cleaning ...................................................................................... 11

TROUBLESHOOTING .................................................................. 12

RECYCLING WITH YOUR COMPACTOR .................................. 12

ASSISTANCE OR SERVICE ......................................................... 13

In the U.S.A ................................................................................ 13

Accessories ................................................................................ 13

WARRANTY .................................................................................. 14

SECURITE DU COMPACTEUR ................................................... 15

INSTALLATION DU COMPACTEUR ........................................... 16

Deballage .................................................................................... 16

Sp6cifications d'emplacement ................................................... 16

Sp6cifications 61ectriques .......................................................... 17

Installation en-dessous du comptoir ......................................... 18

Assainisseur d'air ....................................................................... 19

Changement du panneau d6coratif ........................................... 19

UTIUSATION DU COMPACTEUR ............................................... 21

Fonctionnement du compacteur ................................................ 21

Chargement ................................................................................ 21

Mise en marche du compacteur ................................................ 22

Pour arr_ter le compacteur ........................................................ 22

Enl_vement d'un sac rempli ....................................................... 22

Installation d'un nouveau sac..................................................... 23

ENTRETIEN DE VOTRE COMPACTEUR .................................... 23

Nettoyage ................................................................................... 23

DEPANNAGE ................................................................................. 24

RECYCLAGE AVEC VOTRE COMPACTEUR ............................. 25

ASSISTANCE OU SERVICE ......................................................... 26

Aux Etats-Unis ............................................................................ 26

Accessoires ................................................................................ 26

GARANTIE ..................................................................................... 27

COMPACTOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages inthismanual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using an electrical appliance, basic precautions should always be followed, including the

following:

• Read all instructions before using the compactor.

• Close supervision is necessary when used by or

near children. Do not allow to be used as a toy, or

to run unattended at any time. Lock Key Switch

when not in use and store key out of reach of

children.

• Do not touch moving parts.

• Do not operate with a damaged cord set, plug,

motor, or after damage in any manner. Have the

compactor examined, repaired or adjusted by an

authorized serviceperson.

• Use only for intended use as described in this

manual. Do not use other than manufacturer's

recommended attachments.

Do not compact toxic or volatile flammable material

such as oily rags and insect sprays. Do not compact

lighted cigarettes, cigars, or other hot or burning

items. Do not overload the compactor.

Do not take apart the compactor. Incorrect

reassembly can cause electric shock when

subsequently used.

Handle a loaded trash bag with care. Sharp objects

can pierce the bag and cause injury. Do not

overload trash bag with heavy material such as

glass.

• This compactor is intended for household use only.

SAVE THESE INSTRUCTIONS

INSTALLATION

INSTRUCTIONS

Installer: Leave Use and Care Guide with the homeowner.

Homeowner: Keep Use & Care Guide for future reference and for

local electrical inspectoCs use, if required.

IMPORTANT:

• Do not grasp console to move compactor.

• Begin in the room where the compactor will be located.

1. Remove compactor from shipping carton. Remove all

protective packaging materials such as tape and shipping

pads. Use a mild solution of liquid household cleaner and

warm water to remove waxy residue caused by protective

shipping material. Dry thoroughly with a soft cloth. For more

information, see the "Cleaning" section.

2. Check to be sure the power cord is attached to the cord clip

on the rear of the compactor.

1 r

1. Cord clip

Place the two corner posts from the carton on the floor near

the compactor. Open the compactor drawer and remove any

shipping materials or other items from the drawer. Do not

remove the compactor bag. Grasp the handle and raise the

front of drawer until it clears the drawer stops. Grasp sides of

drawer and lift drawer out of compactor. Place the drawer on

the two corner posts.

Place the other two corner posts on the floor to the side of

the compactor. Grasp the sides of the compactor cabinet and

put compactor on its side on top of the corner posts. Remove

the shipping base from the bottom of the compactor.

1. Leveling legs

2. Shipping base

Product dimensions

_ 0

34_"

(86.7 cm)

15" 24"

(38.1 ¢rn) (61 cm)

Cutout dimensions E @C_,t_i;CG! I_i_U_>_;_@IS_S

(7.6 cm)_

18" min.

145.7cm)

24" rain.

(6_ 151/."min.

138.7cm)

34_h" min.

(87 cm)

1. Grounded electrical outlet must be a minimum of 3 in, (X 6 cm)

away from surrounding cabinets or nearby walls as shown. It can

be placed either to the left or the right side of the product.

Clearance dimensions

1. Leave 6 in, (15,2 ore) of clearance space to the right side of

the compactor in order to remove the compactor bags,

2, Leave 23 in, (58,4 cm) of clearance in front of the compactor

in order to fully open or remove the compactor drawe_

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Recommended Grounding Method

This compactor is for use on a single phase, 115-volt, 60 Hz, AC

only 15 or 20 ampere fused and properly grounded circuit and is

equipped with a grounding plug as shown below. Time delay fuse

or circuit breaker is recommended. It is recommended that a

separate circuit serving only this appliance be provided. In the

event of an electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the electric

current. Do not modify the plug attached to the compactor; use

only with a grounded receptacle.

This compactor must be grounded while in use to reduce the risk

of electric shock. The compactor is equipped with a three-

conductor cord and three-prong grounding-type plug to fit the

proper grounding-type receptacle. The green (or green and

yellow) conductor in the cord is the grounding wire. Never

connect the green (or green and yellow) wire to a live terminal.

The outlet should be properly installed and grounded in

accordance with the National Electrical Code and Local codes

and ordinances. No adapter should be used with this appliance.

NOTE: Proper installation is your responsibility. Make sure you

have everything necessary for correct installation. It is the

personal responsibility and obligation of the customer to contact

a qualified installer to assure that electrical installation meets all

national and local codes and ordinances.

Tools and materials needed for installation:

Level Phillips No. 2 Screwdriver

Tape Measure Flat-Head Screwdriver

Pliers %6in. Hex-Head Socket Wrench

Scissors Utility Knife

IMPORTANT:

• DO not grasp control panel to move compactor.

• To prevent damaging floor covering, slide compactor onto

cardboard or hardboard before moving compactor across

floor.

• DO not allow the rear frame of the compactor to touch the

floor covering when lifting or moving compactor.

Undercounter Installation

Measure the height of your cabinet opening. The top of the

compactor should be at least 1/8in. (3 mm) from the top of the

cabinet opening.

The rear wheels are preset for a cabinet opening of 341/4in.

(87 cm). See Position A in picture following.

To adjust for other cabinet opening heights:

• Loosen self-tapping screw just enough to clear stud from

hole in Position "A."

Move the rear wheel and stud to Position "B" or "C" as

needed for your cabinet opening measurement:

Position B: 341/4in. to 347/_6in. (87 to 87.5 cm)

Position C: 34z/_6in. to 345/8in. (87.5 to 88 cm)

NOTE: To level the unit in position "C," you may need to

add shims under the leveling legs.

Tighten screw. Repeat for other rear wheel.

2. Use pliers to lower leveling legs away from cabinet. Adjust

legs so there will be a I/8in. (3 mm) to 1/4in. (6.4 ram) space

between the top of the compactor and the top of the cabinet

opening. Stand the compactor upright.

3. Move the compactor close to its final position.

4. Plug into a grounded 3 prong outlet.

5. Determine if you want the compactor frame or drawer front

flush with the cabinet front.

Using the two #8-18 x 5/16in. screws, install the retaining

brackets to cabinet top as needed:

• If the compactor frame is to be flush with the cabinet

front, place retaining bracket screws through "A."

Ifthe compactor drawer front is to be flush with the

cabinet front, place retaining bracket screws through "C."

If the compactor is to be midway between "A" and "C,"

place the retaining bracket screws through "B."

. . 1

1. Countertep

2. Retaining bracket

6. Carefully lift the front slightly and roll compactor into the

cabinet opening.

Using the two #8-18 x 1/2in. screws, fasten the retaining

brackets to the countertop with the mounting screws.

If brackets cannot be attached to the underside of

countertop, attach mounting clips to brackets. Fasten

compactor to cabinet front with mounting screws through

mounting clips.

Countertop Mounting

1. Wheel bracket assembly

2. Cabinet

3. Locating stud

4. Self-tapping screw (pivot)

1. Countertep

2. Retaining bracket

3. Mounting screw

Cabinet-front mounting

1. Mounting clip

2. Cabinet

3. Retaining bracket

4, Mounting screw

7. Grasp sides of compactor drawer and place bottom of

drawer into tracks. Lift at the handle so drawer will go over

drawer stops. Close drawer. Check to see if drawer opens

freely. If the toe plate rubs against floor, see "Adjusting the

Toe Plate" for further instructions.

Adjusting the Toe Plate

If the toe plate rubs the floor covering, the toe plate clearance

may be changed as follows:

1. Mark on each side of the toe plate the amount of toe plate

that rubs the floor covering.

2. Remove the drawer from the unit. (See Step 3 in the

"Unpacking" section.)

3. Use a ruler and a pencil or chalk to draw a line between the

marks on each side of toe plate.

4. Use scissors or utility knife to cut toe plate along line.

5. Replace drawer. If toe plate still rubs floor covering, repeat

steps 1-4.

The solid air freshener system is designed to help control odors

that might develop in the trash. An air freshener disc can be

purchased in department stores (not sold with compactor). Place

the disk-shaped solid air freshener into the air freshener

compartment. The air freshener should last 4 to 6 weeks. It is

used more rapidly when the temperature is high or the air is very

dry.

There are three options for changing the decorative panel:

• Order an acrylic panel

• Create a custom panel for use with a trim kit

• Create a custom panel for installation without trim

To order an acrylic panel or a trim kit, see the "Assistance or

Service" section for information or call the toll-free number on the

cover.

Tdrn kit panel dimensions

Use these dimension drawings to create a custom panel for use

with a trim kit. Then, follow the installation instructions provided

with the kit.

Flat panel; A 7½2in. (5.6 mm) thick panel is required. This is the

same thickness as a standard V4in. plywood or paneling.

23_"

(60i5 cm)

37.2 cm_

Raised panel: The outer section of panel must be z/._in. (5.6 mm)

thick to fit into trim. Design raised panel sections using

dimensions shown above.

(5.6 ram)

2 ...........

(37.2 cm)

(32 ram)

23 %"

(60.

(8 mm) -*- ' Y,,"

both sides (8 mm)

1. Raised panel or decorative trim

2. Outer section of panel

Trimless panel with handle Trimless panel without handle

Dimensions

Use these dimension drawings to create a custom panel for use

without a trim kit. The panel should be 1/2in. to 5/8in. (13 mm to

16 ram) thick.

NOTE: A thicker panel may need rounded front corners and a

cut-out for access to the handle.

23,3/,_"

(60.5 cm)

Dimensions

Use these dimension drawings to create a custom panel for use

without a trim kit. The panel should be 1/2in. (13 mm) min. thick.

25"

(63.5 cm)

_ 15" _

(38.1 cm)

_ 15" _

(38.1 cm)

Installation

1. Remove foot pedal, toe guard, and decorative panel.

2. Align the top of the custom panel with the bottom of the

handle.

3. Secure the panel from the back using 4 - #8 x 1 in. wood

screws as shown.

4. Reinstall the toe guard using the existing screws and 1/2in.

washer. Then, reinstall the foot pedal.

Installation

1. Remove foot pedal, toe guard, decorative panel, and handle.

2. Align the bottom of the custom panel with the bottom of the

drawer front.

3. Secure the panel from the back using 4 - #8 x 1 in. wood

screws as shown.

4. Attach a 15 in. x I/2in. quarter-round filler along the top of the

drawer front using glue or screws.

5. Reinstall the toe guard using the existing screws and 1/2in.

washer. Then, reinstall the foot pedal.

1. Handle

2. Custom Panel

3. #8 x 1" Wood Screws

4. Toe Guard

5. Washer

& Toe Guard Screw

1. Custom Panel

2. 15"x ½" Quarter-round

3. #8 x 1" Wood Screws

4, Toe Guard

5. Washer

6, Toe Guard Screw

COMPACTOR USE

The compacting ram is the part of the compactor which

compresses the trash. The compacting ram does not go to the

bottom of the drawer. You will not see compacting of trash the

first few times you load the compactor.

NOTE: The compactor drawer should be more than 1/2full before

the compactor can begin to compress the load.

You may hear a noise when glass breaks. Strong glass bottles

may not break at all. The trash in a full compactor bag will be

about 1/4the size of its original bulk.

N-.

= tlXi-i i

I I i

_.. I_ _ _ i

Load bulky trash, bottles, and cans in the center of the drawer.

Dottles or cans not placed in the center may become caught

between the ram and the drawer. The Drawer Monitor Switch

then senses a '*misload" and causes the ram to return to the "up"

position without compacting.

Explosion Hazard

Do not compact any container, aerosol cans, or

cloths which might contain insecticide, hair spray,

engine starting fluid, paints, liquids, thinners, or

any other poisonous or explosive products.

Doing so can result in death, explosion, or fire.

Cut Hazard

Do not push items down into compactor with

hands or feet.

Doing so can result in cuts.

NOTE: You will not see compacting of trash the first few times

you load the compactor. The compactor drawer should be about

V2full before the compactor can begin to compress the load.

1. Open the drawer. Lift and pull the handle or press the toe bar

to open the drawer.

NOTE: Pressing the toe bar opens the container only 3 in. to

6 in. (7.6 cm to 15.2 cm), depending on the load.

Place trash in compactor.

• Wrap or cover wet or messy trash.

• Do not compact items that may develop offensive odors

such as raw meat, fish, grapefruit dnds, disposable

diapers, or personal hygiene items.

• Load bottles or cans on their sides in the center of the

drawer. Do not load bottles in an upright position.

3. Close the drawer.

1. Turn the Control Knob to START.As soon as the compactor

starts, release the Control Knob. The knob will then advance

to the RUN position and begin the compacting cycle.

2. A complete compacting cycle takes about 27 seconds. The

compactor will automatically stop.

NOTE: When the compacting cycle is done, turn the Key-Knob to

OFF & LOCK. Remove the Key-Knob and store it out of children's

reach.

1. Turn the Control Knob to OFF & LOCK.

2. Turn the Control Knob to RUN. This will raise the ram to its

topmost position.

The compactor will automatically advance to the end of the

cycle and stop.

3. You can open the drawer after the compactor stops.

When the trash is compacted to the top of the drawer, remove

the bag. If the bag is too heavy, compact less trash before

emptying it in the future.

Cut Hazard

Do not push items down into compactor with

hands or feet.

Doing so can result in cuts.

Pull the drawer completely open.

Remove top of bag from bag retainer buttons. Pull up all four

bag cuffs. Close bag with twist tie provided.

Push Side-Lock Latch down and tilt drawer side open.

Lift out bag.

IMPORTANT:

Before installing a new bag, be sure:

• The drawer side is securely locked.

• The container is clean and free of debris.

Do not use any kind of bag other than those designed especially

for use in your compactor. Order replacement compactor bags

through your local dealer or by calling the toll-free number on the

cover or in the "Assistance or Service" section.

Place folded bag into the drawer. Open bag and pull top

edges over the drawer top.

2. Lock bag in place by pulling the four prepunched holes over

the bag retainer buttons. Holes will expand over the buttons

without damaging the bag.

3. Press inside of bag against the drawer bottom, sides and

corners for a smooth fit.

COMPACTOR CARE

Your new compactor is designed to give you many years of

dependable service. However, there are a few things you are

expected to do in order to maintain your compactor properly.

This section will tell you how to clean and care for your

compactor.

Before cleaning the compactor, turn the Key-Knob (or Key-

Switch) to the OFF & LOCK position and remove it.

NOTE: Any services other than those outlined in this section

should be performed by a designated service representative.

Cleaning Exterior Surfaces

1. Wash exterior surfaces (including stainless steel) with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners. Rinse and dry thoroughly

with a soft cloth.

2. Wipe up spills right away. Some foods can damage the finish

if left on the compactor surface.

Cleaning Inside _e Drawer

NOTE: You may want to wear protective gloves as there may be

bits of glass in the drawer.

1. Remove the bag. (See the "Removing a Filled Bag" section.)

2. Press down on the lever-action lock (or Side-Lock latch).

3. Hold the lever-action lock down and tilt the side of the drawer

out until the lock clears the drawer front.

NOTE: If desired, the drawer side can be removed by tilting it

up, then lifting it out.

4. Wash the interior of the drawer with a clean sponge or soft

cloth and a mild detergent in warm water. Rinse and dry

thoroughly with a soft cloth.

5. If the drawer side was removed, slide it back into the tilted

position.

6. Press the lever-action lock (or Side-Lock Latch) down while

pushing the drawer side to the upright position.

7. Latch the drawer side by pushing up the lever-action lock (or

Side-Lock Latch).

Cleaning Inside _e Cabinet

NOTE: You may want to wear protective gloves as there may be

bits of glass in the cabinet.

1. Pull the drawer out until it stops.

NOTE: Look to see how the drawer rollers move in the tracks.

It will be easier to replace the drawer when you are finished

cleaning.

2. Lift the front of the drawer to clear the stops.

3. Grasp the drawer on the sides and pull it out the rest of the

way. Set the drawer down gently.

4. Vacuum the inside of the cabinet. Liquid spills or wet trash

should be cleaned up by hand, or by using a vacuum

designed to pick up liquids.

5. Wash the inside of the cabinet with a clean sponge or soft

cloth and a mild detergent in warm water. Rinse and dry

thoroughly with a soft cloth.

6. To replace the drawer, grasp it by the sides and insert the

rollers onto the tracks.

7. Lift the front of the drawer and push it in fully past the stops.

Cleaning the Ram

NOTE: You may want to wear protective gloves as there may be

bits of glass on the ram cover.

1. Wipe glass particles off of the ram cover with a cloth or paper

towels.

2. Remove foods with a clean sponge or soft cloth and a mild

detergent in warm water. Rinse and dry thoroughly with a soft

cloth.

c=J

Cleaning Before a Vacation

If you will be away for more than a couple of days, remove the

compactor bag. Remove the Key-Knob (or Key-Switch) and store

it out of children's reach.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the

cost of an unnecessary service call.

Trash is not compacting

• Is the drawer less than half full? Drawer must be more than

half full before trash is compacted.

Your compactor won't operate

• Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

• Has a household fuse or circuit breaker tripped? Replace

the fuse or reset the circuit breaker.

• Is the drawer completely closed? Close the drawer firmly

and start the compactor again.

• Is the Key-Knob turned all the way to START? Turn the

Key-Knob (Key-Switch) fully to START and release (on some

models). See the "Starting the Compactor" section.

• Did you press ON before pressing START? Press ON

before pressing START (on some models). See the "Starting

the Compactor" section.

The drawer won't open

• Is the ram all the way up? Drawer will open only when ram is

fully raised.

• To raise the ram on models with a Key-Knob (or Key-

Switch): Turn the Key-Knob (Key-Switch) to START and

release. See the "Starting the Compactor" section.

• To raise the ram on models with push button controls:

Press OFF, and then press ON. See the "Starting the

Compactor" section.

There is not enough compaction or force

• Do you use the compacting cycle frequently enough?

Compacting works best when only a few items are loaded.

Bottles don't break

• How often do you notice this? Bottles will not break every

time. The thickness of the bottle's glass and the content of

the trash load below it may prevent the bottle from breaking.

RECYCLINGWITHYOUR

COMPACTOR

PETE HDPE V

& & &

LDPE PP PS

These codes indicate which type of plastic was used

in manufacturing the container. Your recycling

program will confirm which codes are accepted for

recycling.

OTHER

Plastics with this symbol cannot be recycled,

Items with this symbol can be recycled or were made

from recycled materials.

A compactor makes recycling and landfill reduction efforts more

effective and efficient.

R_lingGuidelines

Contact your community recycling program or local recycling

organizations to find out which items are accepted for recycling

and how they should be prepared and organized. These

programs will provide essential recycling guidelines:

• Method and frequency of collection--curbside collections

and drop-oft centers.

• Categories of recyclable items, and how to distinguish

between them. Plastic containers are identified by codes on

the bottom. Sort by the numbers inside the triangular arrows.

For example, most plastic soda bottles and some cleaning

bottles have code 1; most milk and water jugs, laundry and

personal hygiene product containers have code 2. Paper and

cardboard containers (paperboard) also have recycle

symbols to indicate a container is recyclable.

Preparations of recyclable items. Most recycling programs

provide specific guidelines on preparation. For example,

aluminum cans and plastic containers need to be rinsed out,

lids removed, but often labels can be left on.

IMPORTANT:

• Some items, such as glass, should not be compacted.

• Most recycling programs will not accept crushed glass.

• Check with your recycling program for specific guidelines on

preparing recyclables.

Organizing the Recycling Workspace

Convenient recycle bins are made to fit in the compactor drawer.

These bins, as well as plastic compactor bags, can be purchased

in a variety of colors at hardware stores and supermarkets. Set

up a system of color-coded bags in an area chosen for

processing recyclables. Each color can represent a category of

recyclable items, based on types specified by your recycling

program. Separate recyclable items from non-recyclable items:

• Recyclable items can be sorted using the color-coded bags.

Prepare items according to guidelines provided by your

recycling program.

Non-recyclable items should be compacted because

compaction reduces trash volume to its original size: four

bags of trash can be compacted into one bag. This

contributes to reducing landfill volume and related waste

transportation burdens.

REMEMBER: Do not expect items which contain minimal air,

such as folded newspapers, to compact significantly.

Compacting Recyclable Items

Most recycling programs want the consumer to crush or flatten

recyclable items such as plastics, cans, and paperboard.

Compacting recyclable items consolidates volume and thereby

reduces transportation costs--and also helps manage recycling

workspace more effectively. The compactor is ideal for such a

task. When a plastic bag is full enough to require compacting,

place the bag in the drawer as shown in "Installing a New Bag."

Then follow instructions in "Compactor Use." When the

compacting cycle is complete, remove the plastic bag as shown

in "Removing a Filled Bag" and return it to storage until it is full

enough to recycle.

Remember, compacting both recyclables and non-recyclables

means less solid waste and waste transportation costs--and a

better environment for all.

ASSISTANCEORSERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If the problem is not due to one of the items listed in the

"Troubleshooting" section,..

Call the dealer from whom your appliance was purchased, or call

Maytag Appliance Sales Company, Jenn-Air Customer

Assistance at 1-800-688-1100 or 1-423-472-3333 to locate an

authorized service company. When calling, please know the

purchase date and the complete model and serial number of your

appliance. Be sure to retain proof of purchase to verify warranty

status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Customer Service

Attn.: CAIR ®Center

P.O. Box 2370

Cleveland, TN 37320-2370

Web address: www.jennair.com

Or call: 1-800-688-1100.

U.S. customers using TrY for deaf, hearing impaired or speech

impaired, call: 1-800-688-2000 (Monday-Friday, 8:00 a.m.-8:00

p.m. Eastern Time).

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

All specifications are subject to change by manufacturer without

notice.

To order a color-matched trim kit for the installation of a custom-

made panel, contact your local authorized dealer.

Replacement Bags - Call for Part Number

Trim Kits for Custom Front Panels:

Order Part #TCDW (white), TCDB (black), TCDQ (bisque) (Trim kit

for custom made panel)

Order Part #TCDS (Stainless steel door panel)

Reduce - Reuse - Recycle

JENN-AII COMPACTOR WARRANTY

FULL ONE-YEAR WARRANTY

For one (1) year from the date of original retail purchase, any part which fails in normal home use will be repaired or replaced free of

charge.

LIMITED TWO-YEAR WARRANTY

From the second year through the end of the third year following the date of original retail purchase, parts which fail in normal home use

will be repaired or replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage and

transportation.

PLEASE NOTE: The full warranty applies only when the compactor is located in the United States or Canada. Compactors located

elsewhere are covered by the limited warranty only, including limited warranties for parts which fail during the first year.

CANADIAN RESIDENTS: These warranties cover only those compactors installed in Canada that have been listed with

Canadian Standards Association unless the compactors are brought into Canada due to transfer of residence from the United

States to Canada.

The specific warranties expressed above are the ONLY warranties provided by the manufacturer. These warranties

give you specific legal rights, and you may also have other rights that vary from state to state.

What is Not Covered by These Warranties:

1. Conditions and damages resulting from any of the following:

a. Improper installation, delivery or maintenance.

b. Any repair, modification, alteration or adjustment not authorized by the manufacturer or an authorized servicer.

c. Misuse, abuse, accidents or unreasonable use.

d. Incorrect electric current, voltage or supply.

e. Improper setting of any control.

2. Warranties are void if the original serial numbers have been removed, altered or cannot be readily determined.

3. Products purchased for commercial or industrial use.

4. The cost of service or service call to:

a. Correct installation errors.

b. Instruct the user on proper use of the product.

c. Transport the appliance to the servicer.

5. Consequential or incidental damages sustained by any person as a result of any breach of these warranties.

Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above

exclusion may not apply.

User's guides, service manuals and parts catalogs are available from Maytag Appliances Sales Company, Maytag

Customer Assistance.

10/0I

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your compactor to

better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the inside wall of the compactor drawer.

Dealer name

Address ...................................

Phone number

Model number

Serial number ...............................

Purchase date

SI CURITEDUCOMPACTEUR

Votre s_curit_ et celle des autres est tr_s importante.

Nous donnons de nombreux messages de s_curit_ importants darts ce manuel et sur votre appareil m_nager.

Assurez-vous de toujours lire tousles messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit6.

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiets de d6c_s et de blessures graves

& vous et & d'autres.

Tousles messages de s_curit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de ddcbs ou de blessure grave si

vous ne suivez pas imm_diatement les instructions.

Risque possible de ddc_s ou de blessure grave

si vous Re suivez pas les instructions.

Tousles messages de s_curit6 vous diront quet est le danger potentiel et vous disent comment r6duire le risque de

blessure et ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES INSTRUCTIONS DE SI=CURITI=

AVERTISSEMENT : Lors de I'utilisation d'appareils _lectrom_nagers, il convient d'observer certaines

pr6cautions 616mentaires dont les suivantes :

• Lire toutes les instructions avant d'utiliser le

compacteur.

• Une surveillance etroite est necessaire, Iorsque

I'appareil est employe par ou pros d'enfants. Ne

pas permettre d'utiliser I'appareil comme un jouet,

ou le faire fonctionner sans surveillance. Verrouiller

I'interrupteur & cl6 Iorsque I'appareil n'est pas

utilis6 et garder la cle hors d'atteinte des enfants.

• Ne pas toucher les pi_ces mobiles.

• Ne pas faire fonctionner le compacteur si le cordon

d'alimentation, la fiche de branchement, le moteur

sont endommages ou apr6s tout dommage

quelconque. Faire examiner, r6parer ou ajuster le

compacteur par un technicien autorise.

Utiliser uniquement pour I'usage auquel il est

destin6, tel que decrit dans ce manuel. Ne pas

utiliser des accessoires autres que ceux qui sont

recommand6s par le fabricant.

Ne pas utiliser cet appareil pour compacter des

produits toxiques ou fluides inflammables tels que

chiffons imbib6s d'huile et vaporisateurs insecticides.

Ne pas soumettre au compacteur les articles comme

cigarettes ou cigares allum6s, ou autres objets en

combustion ou chauds. Ne pas surcharger le com-

pacteur.

Ne pas d6monter le compacteur. Un remontage

incorrect peut 6tre & I'origine d'un choc 61ectrique,

Iors de I'utilisation subsequente.

Manipuler avec soin un sac rempli de d6chets. Des

objets pointus peuvent percer le sac et causer des

blessures. Ne pas surcharger le sac de dechets

avec des mat_riaux pesants tels que le verre.

Ce compacteur est destin6 & I'usage domestique

uniquement.

CONSERVEZ CES INSTRUCTIONS

INSTALLATIONDU

COMPACTEUR

Installateur : Laissez le guide d'utilisation et d'entretien au

propri6taire.

Propri_taire : Gardez le guide d'utilisation et d'entretien pour

r6f6rence ult6rieure et pour I'usage de I'inspecteur local

d'61ectricit6, au besoin.

IMPORTANT :

• Ne pas saisir la console pour d6placer le compacteur.

• Commencer dans la piece oQ le compacteur sera install&

1. Retirer le compacteur de son emballage. Enlever tousles

mat6riaux d'emballage et de protection comme ruban adh6sif

et cales. Enlever avec une solution d'eau et de produit de

nettoyage m_nager liquide doux, les r6sidus de cite ]aiss_s

par les mat6riaux de protection. S6cher completement avec

un chiffon doux. Pour de plus amples renseignements, voir la

section "Nettoyage".

2. V6rifier que le cordon d'alimentation 61ectrique est fix6 &

I'agrafe & I'arriere du corn 3acteur.

1, Agrafe du cordon d'alimentation

Placer les deux cornieres de protection sur le plancher, pres

du compacteur. Ouvrir le tiroir du compacteur et retirer tous

les mat6riaux d'emballage ou autres articles exp6di_s dans le

tiroir. Ne pas retirer le sac du compacteur. Saisir la poign6e et

soulever I'avant du tiroir pour le faire passer au-dessus des

but6es. Saisir les c6t6s du tiroir et soulever le tiroir pour le

retirer du compacteur. Placer le tiroir sur les deux corni_res

de protection.

Risque du poids excessif

Utiliser deux ou plus de personnes pour d(_placer

et installer le compacteur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Placer les deux autres cornieres de protection sur ie plancher,

pres du compacteur. Saisir les c6t6s de la caisse du

compacteur et placer le compacteur sur le c6t6, sur les

cornieres de protection. Retirer la base plac_e au fond du

compacteur avant I'exp6dition.

1, Pieds de nivellement

2, Base d' expedition

Dimensions du produit

-,co, l1

(38,1 cm) (61 cm)

Dimensions de I'encastrement

(7,6 cm)_._

18" min.

(45,7 cm)

24" min.

(6_ 15¼"min.

(38,7 cm)

4¼" mill.

(87 cm)

1. Prise _lectrique reli_e _ la terre qui dolt _tre _ une distance

minimum de 3 po (7,6 cm) des armeires voisines ou des tours

lat_raux tel qu'illustr_. Erie peut #tre plac#e du c6t# droit ou du

c6te gauche du produit.

Dimensions de d_gagement

Risque de choc dlectrique

Brancher sur une prise & 3 alvdoles reli_e

la terre.

Ne pas eniever la broche de liaison b la terre.

Ne pas utiliser un adaptateur.

Le non-respect de ces instructions peut causer

un ddcbs, un incendie ou un choc _lectrique.

M_thode recommandde de liaison b la terre

Le compacteur est aliment6 par un circuit de 115 V CA

monophas6, 60 Hz, 15 ou 20 A; le circuit dolt Ctre prot6g_ par un

fusible et convenablement reli_ a la terre par I'interm_diaire de la

fiche de branchement avec broches de liaison a la terre (volt

I'illustration ci-dessous). On recommande I'emploi d'un

disjoncteur ou d'un fusible temporis6. II est pr6f6rable que cet

appareil soit aliment6 par un circuit distinct. Au cas oQ un court-

circuit se produirait, la liaison & la terre r6duit le risque de choc

61ectrique, car le courant peut ainsi s'_chapper directement vers

la terre. Ne pas modifier la fiche jointe au compacteur, et utiliser

seulement avec une prise reli6e a la terre.

Le compacteur dolt _tre reli6 & la terre Iorsqu'il est utilis6 pour

r_duire le risque de choc 6iectrique. Le compacteur est 6quip_

d'un cordon & trois conducteurs et d'une fiche a trois broches de

type reli_ b,la terre, pour convenir a la prise de courant

appropri_e reliCe a la terre. Le conducteur vert (ou vert et jaune)

dans le cordon est le fil de liaison a la terre. Ne jamais connecter

le fil vert (ou vert et jaune) a une borne active. La prise dolt _tre

convenablement install_e et reli_e b,la terre en conformit_ avec

les dispositions du Code national des installations _lectriques et

des codes et reglements Iocaux. Ne pas utiliser un adaptateur

pour le branchement de cet appareiL

1. Laisser un espace fibre de 6 po (!5,2 cm) du cSt_ dreit

du compacteur pour extraire les sacs du compacteu_

2. Laisser un espace libre de 23 po (58,4 cm) en avant

du compacteur pour ouvfir completement ou retirer le

tiroir du compacteu_

REMARQUE : [_'installation appropd6e est ta responsabilit6 du

propd@taire. S'assurer que vous avez tout le n6eessaire pour

eorriger I'installation. O'est la responsabilit6 et I'obligation

personnel du cbient de eontaeter un installateur qualifi6 pour

s'assurer que Finstallation 61eetrique r6pond aux codes et

regtements nationaux et toeaux.

Outinage el mat_riaux requis pour I'instanation :

Niveau

Tournevbs Phillips n°2

Ruban &mesurer Tournevis & lame plate

Pinces

Cle & douille hexagonale de %epo

Ciseaux Couteau utilitaire

IMPORTANT :

• Ne pas saisir la console pour d6placer le compacteur.

• Glisser le compacteur sur becarton ou le panneau de bois dur

avant de d6placer le compacteur sur bepbancher, pour

emp_cher d'endommager le recouvrement du plancher.

• Ne pas laisser le ch&ssis arriere du compacteur toucher be

recouvrement du plancher Iors du soulevement ou du

d_placement du compacteur.

Montage en-dessous du comptoir

1. Mesurer bahauteur de b'ouverture de I'armoire. Le sommet du

compacteur devrait _tre au moins a V8po (3 mm) du sommet

de I'ouverture de I'armoire.

Les roues arriere sont pr6r6gb_es pour b'ouverture d'une

armoire d'une hauteur de 34 V4po (87 cm) (Position "A").

Ajustement pour d'autres hauteurs d'ouverture d'armoire:

Pour ajuster besautres hauteurs d'ouverture d'armoire,

desserrer la vis, juste assez pour pouvoir extraire le piton

du trou de positionnement "A".

D6placer la roue arriere et le piton a la position "B" ou "C"

au besoin, pour bamesure d'ouverture de I'armoire :

Position B : hauteur bibrede 34 V4po a 34 7Aepo (87

87,5 cm)

Position C : hauteur libre 34 7Aepo a 34 % po (87,5

88 cm)

REMARQUE : Pour mettre d'aplomb I'appareil en

position C, vous devez peut-_tre ajouter des cales sous

les pieds de nivellement.

Serrer la vis. R6p6ter ces op6rations pour I'autre roue

arriere.

2. Utiliser les pinces pour abaisser les pieds de nivellement hors

du cabinet. Ajuster les pieds de sorte qu'il y aura de V8po

(3 ram) a V4po (6,4 ram) d'espace entre le sommet du

compacteur et le sommet de I'ouverture de I'armoire. Placer

le compacteur verticalement.

3. D6placer le compacteur jusqu'au voisinage imm6diat de la

position d'installation finale.

4. Brancher sur une prise a 3 alv6oles reli6e a la terre.

5. D_terminer si vous voulez que le cadre du compacteur ou be

devant du tiroir soit en affbeurement avec le devant de

I'armoire.

Utilisant besdeux vis n° 8 de 18 x _Aepo (8 mm), installer les

brides qui restent au sommet de bacaisse, au besoin.

• Si le ch&ssis du compacteur dolt _tre en affleurement

avec I'avant des armoires, placer les vis de retenue de la

bride darts les trous "A" des brides.

• Si bedevant de la bride du tiroir du compacteur dolt Ctre

en affleurement avec I'avant de I'armoire, placer les vis de

retenue de la bride dans les trous "C" des brides.

• Si le compacteur dolt _tre instalb_ & une position

interm_diaire, entre "A" et "C" placer les vis de retenue de

la bride darts le trou "B".

1. Dessus du comptoir

2. Bride de retenue

Soubever le devant begerement et faire rouler becompacteur

darts I'ouverture de I'armoire.

En utilisant besdeux vis n° 8 - 18 x V_po (12 mm), fixer les

brides de retenue en-dessous du comptoir avec besvis de

montage.

Si besbrides ne peuvent pas Ctre fix_es au-dessous du

comptoir, fixer besagrafes de montage aux brides. Fixer be

compacteur au devant du cabinet avec les vis darts les brides

de montage.

Installation sous le comptoir

1. Bride porte-roue

2. Caisse

3. Piston de positionnement

4, Vis autotaraudante (pivot)

1. Dessus du comptoir

2. Bride de retenue

3. tfls de montage

Montage & I'avant de I'armoire

1. Bride de montage

2. Armoire

3, Bride de retenue

4. Vis de montage

7. Saisir les c6t6s du tiroir du compacteur et placer le fond du

tiroir darts les glissieres. Soulever le tiroir par la poign6e pour

fake passer I'avant du tiroir au-dessus des but6es. Fermer le

tiroir. Verifier qu'il est possible d'ouvrir facilement le tiroir. Si la

p6dale frotte contre le plancher, voir d'autres instructions &la

section "R6glage de la p6dale".

R_glage de la p6dale

Si la p6dale frotte contre le rev¢tement du plancher, on peut

modifier la hauteur de la p_tale comme suit :

f. Marquer de chaque c6t6 de la p6dale la largeur du mat6riau

qui cause le frottement sur le rev¢tement du plancher.

2. Retirer le tiroir de I'appareiL (Voir 1'6tape 3 a la section

"Deballage".)

3. ,&I'aide d'une regle et d'un crayon ou d'une craie, tracer une

ligne entre les marques trac6es de chaque c6t6 de la p6dale.

4. A I'aide de ciseaux ou d'un couteau utilitaire, d6couper la

p6dale le long de la ligne.

5. R6installer le tiroir. Si la p6dale frotte toujours sur le

rev6tement du plancher, r6p6ter les 6tapes 1 a 4.

@ C;St

Le systeme d'assainisseur d'air solide est congu pour aider &

contr61er des odeurs qui peuvent se d6velopper dans les

d6chets. Un assainisseur d'air en forme de disque peut 6tre

achet6 darts les grands magasins (non vendu avec le

compacteur). Placer I'assainisseur d'air solide en forme de

disque dans le compartiment de I'assainisseur d'air.

L'assainisseur d'air devrait durer de 4 a 6 semaines. II s'use plus

rapidement Iorsque la temperature est 61ev6e or Iorsque Fair est

tres sec.

II existe trois options pour changer le panneau d6coratif :

• Commander un panneau acrylique

• Cr6er un panneau personnalis6 a utiliser avec une trousse

de garniture

• Crier un panneau personnalis6 pour installation sans

garniture

Pour commander un panneau acrylique ou une trousse de

garniture, voir la section "Assistance ou service" pour des

renseignements ou composer sans frais le num6ro de t616phone

sur la couverture.

Dimensions du panneau avec trousse de garniture

Utiliser ces dessins de dimensions pour cr6er un panneau

personnalis6 a utiliser avec une trousse de garniture. Ensuite,

suivre les instructions d'installation fournies avecla trousse.

Panneau uni : Un panneau d'une 6paisseur de 7/_po (5,6 ram)

est requis. C'est la m6me 6paisseur qu'un panneau en

contreplaqu6 de V4po (6,4 ram) ou panneau standard.

23_"

(60,i cm)

_( f4%"

37,2 cm_

Panneau en relief : La section externe du panneau dolt _tre de

V= po (5,6 ram) d'6paisseur pour convenir & la garniture. Planifier

les sections de panneau en relief en utilisant les dimensions

illustr_es ci-dessus.

(5,6 mm)

2 ...........

14%"

(37,2 cm)

1_ _

(32 ram)

23%"

(60,5 cm)

(8 mm) _ _ ' y.,

les deux c6t6s (8 mm)

1, Panneau enrelief ougarniture

deeoradve

2. Section externedupanneau,

Panneau sans garniture avec poign_e Panneau sans garniture sans poign_=e

Dimensions Dimensions

Utiliser ces dessins de dimensions pour cr6er un panneau

personnalis6 &utiliser sans trousse de garniture. Le panneau doit

mesurer 1/2po & % po (13 mm& 16 ram) d'6paisseur.

REMARQUE : Un panneau plus _pais peut avoir besoin de coins

avant arrondis et un d6coupage pour acc_s & la poign6e.

23,3/,_"

(60,5 cm)

_ 15" _

(38,1 cm)

Utiliser ces dessins de dimensions pour cr6er un panneau

personnalis6 &utiliser sans trousse de garniture. Le panneau doit

mesurer 1/2po (13 ram) d'6paisseur au minimum.

Installation

25"

(63,5 cm)

,.-, 15" _

(38,1 cm)

Installation

1. Enlever ia p_dale, le garde-pieds et le panneau d6coratif.

2. Aligner le sommet du panneau personnalis_ avecla base de

la poign6e. 3.

3. Fixer le panneau de I'arriere en utilisant 4 vis & bois n° 8 x 1

po comme illustr& 4.

4. R6installer le garde-pieds en utilisant les vis existantes et une

rondelle de 1/2po. Ensuite, r6installer la p_dale. 5.

1. Enlever la p6dale, le garde-pieds, le panneau d6coratif et la

poign6e.

2. Aligner la base du panneau personnalis_ avec la base du

devant du tiroir.

Fixer le panneau de I'arriere en utilisant 4 vis & bois n° 8 x 1

po comme illustr&

Fixer un joint d'un quart-de-rond de 15 pox V2pole long du

sommet du tiroir a I'avant en utilisant de la colle ou des vis.

R_installer le garde-pieds en utilisant les vis existantes et une

rondelle de 1/2po. Ensuite, r6installer la p6dale.

1. Poignee

2, Panneau

personnalis_

3. Vis _ bois no8 x 1po

4. Garde-pieds

5. Rondelle

6, Vis du garde-pieds

1.Panneau personnalis_

2. Quart-de-rond de 15po

x½po

3, Visa bois no8 x 1 po

4. Garde-pieds

5. Rondelle

6, Vis du garde-pieds

La page charge ...

Jenn-Air TC507 Manuel utilisateur

Marque: Jenn-Air

Modèle: TC507

Catégorie: Compacteur de déchets

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air TC507 User manual

Jenn-Air TC507 Manuel utilisateur

Jenn-Air TC507 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents