Empire Heating Systems DV55E Le manuel du propriétaire

Marque: Empire Heating Systems

Modèle: DV55E

Taper: Le manuel du propriétaire

Ce manuel convient également à

High-Efficiency Direct-Vent Wall Furnace (DV55E)

Page 1

Patent # 5.664.555

FAN TYPE DIRECT VENT

WALL FURNACE

For Installation In

Manufactured (Mobile Home),

Modular Or Residential Homes

MODELS:

DV-55E-5

This appliance may be installed as an OEM

installation in a manufactured home (USA

only) or mobile home and must be installed

in accordance with the manufacturer's in-

structions and the Manufactured Home Con-

struction and Safety Standard, Title 24 CFR,

Part 3280, in the United States, or the Mobile

Home Standard, CAN/CSA Z240 MH Series,

in Canada.

This appliance is only for use with the type(s)

of gas indicated on the rating plate. A conver-

sion kit is supplied with the appliance.

WARNING

FIRE OR EXPLOSION HAZARD

If the information in these instructions is



may result causing property damage,

personal injury or loss of life.

— Do not store or use gasoline or other



vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

 

 

not use any phone in your building.

 

 

from a neighbor’s phone. Follow the

gas supplier’s instructions.

 



— Installation and service must be



service agency or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

WARNING

If not installed, operated and maintained in

accordance with the manufacturer's instructions,

this product could expose you to substances in

fuel or from fuel combustion which can cause

death or serious illness.

INSTALLATION INSTRUCTIONS

AND OWNER'S MANUAL

19563-9-0519Page 2

TABLE OF CONTENTS

SECTION PAGE

Important Safety Information ..................................................................................................................................... 3

Safety Information for Users of Propane Gas ........................................................................................................... 4

Requirements for Massachusetts ............................................................................................................................. 5

Introduction ............................................................................................................................................................ 6-7

Specications ............................................................................................................................................................ 7

Gas Supply ............................................................................................................................................................... 8

Gas Conversion Instructions ..................................................................................................................................... 9

Clearances .............................................................................................................................................................. 10

Furnace Installation ............................................................................................................................................ 10-12

Lighting Instructions ............................................................................................................................................... 13

Wiring ...................................................................................................................................................................... 14

Maintenance ........................................................................................................................................................... 15

Operation and Troubleshooting .......................................................................................................................... 16-17

How to Order Repair Parts ...................................................................................................................................... 18

Parts List ................................................................................................................................................................ 18

Parts View ............................................................................................................................................................... 19

Warranty .................................................................................................................................................................. 20

19563-9-0519 Page 3

 



draperies.

 

of high surface temperatures and should stay away

to avoid burns or clothing ignition.

 

they are in the same room as the appliance.

 

placed on or near the appliance.

 

an appliance must be replaced prior to operating the

appliance.

 

 

 

or residential installation convertible for use with

      

provision is made for the simple conversion from

one gas to the other.

 Installation and repair should be done by a QUALIFIED

SERVICE PERSON. The appliance should be

inspected before use and at least annually by a

     

       

carpeting, bedding materials, etc. It is imperative

that control compartments, burners and circulating

air passageways of the appliance be kept clean.

 put anything around the furnace that will



  keep the appliance area clear and free from





  examine venting system periodically and replace

damaged parts.

 make a periodic visual check of burner. Clean

and replace damaged parts.

 use this heater if any part has been under



to inspect the heater and to replace any part of the

control system and any gas control which has been

under water.

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

IMPORTANT SAFETY INFORMATION

19563-9-0519Page 4

Some people cannot smell well. Some people cannot smell the

odor of the chemical put into the gas. You must nd out if you can

smell the odorant in propane. Smoking can decrease your ability

to smell. Being around an odor for a time can affect your sensitivity

or ability to detect that odor. Sometimes other odors in the area

mask the gas odor. People may not smell the gas odor or their

minds are on something else. Thinking about smelling a gas odor

can make it easier to smell.

The odorant in Propane Gas is colorless, and it can fade under

some circumstances. For example, if there is an underground leak,

the movement of the gas through soil can lter the odorant. Odor-

ants in Propane Gas also are subject to oxidation. This fading can

occur if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That will

take some of the odorant out of the gas, reducing its odor intensity.

Propane Gas may stratify in a closed area, and the odor intensity

could vary at different levels. Since it is heavier than air, there may

be more odor at lower levels. Always be sensitive to the slightest

gas odor. If you detect any odor, treat it as a serious leak. Imme-

diately go into action as instructed earlier.

Propane is a ammable gas which can cause res and explosions.

In its natural state, propane is odorless and colorless. You may not

know all the following safety precautions which can protect both you

and your family from an accident. Read them carefully now, then

review them point by point with the members of your household.

Someday when there may not be a minute to lose, everyone's

safety will depend on knowing exactly what to do. If, after reading

the following information, you feel you still need more information,

please contact your gas supplier.

• Learn to recognize the odor of Propane Gas. Your local Propane

Gas Dealer can give you a "Scratch and Sniff" pamphlet. Use

it to nd out what the propane odor smells like. If you suspect

that your Propane Gas has a weak or abnormal odor, call your

Propane Gas Dealer.

• If you are not qualied, do not light pilot lights, perform service,

or make adjustments to appliances on the Propane Gas system.

If you are qualied, consciously think about the odor of Propane

Gas prior to and while lighting pilot lights or performing service

or making adjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the Propane Gas odor. Do not try to

light pilot lights, perform service, or make adjustments in an

area where the conditions are such that you may not detect

the odor if there has been a leak of Propane Gas.

• Odor fade, due to oxidation by rust or adsorption on walls of

new cylinders and tanks, is possible. Therefore, people should

be particularly alert and careful when new tanks or cylinders

are placed in service. Odor fade can occur in new tanks, or

reinstalled old tanks, if they are lled and allowed to set too

long before relling. Cylinders and tanks which have been out

of service for a time may develop internal rust which will cause

odor fade. If such conditions are suspected to exist, a periodic

sniff test of the gas is advisable. If you have any question about

the gas odor, call your Propane Gas Dealer. A periodic sniff

test of the Propane Gas is a good safety measure under any

condition.

• If, at any time, you do not smell the Propane Gas odorant and

you think you should, assume you have a leak. Then take the

same immediate action recommended above for the occasion

when you do detect the odorized Propane Gas.

• If you experience a complete "gas out," (the container is under

no vapor pressure), turn the tank valve off immediately. If the

container valve is left on, the container may draw in some air

through openings such as pilot light orices. If this occurs,

some new internal rusting could occur. If the valve is left

open, then treat the container as a new tank. Always be sure

your container is under vapor pressure by turning it off at the

container before it goes completely empty or having it relled

before it is completely empty.

• Do not operate electric switches, light matches, use your phone.

Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do

that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• Propane Gas is heavier than air and may settle in low areas

such as basements. When you have reason to suspect a gas

leak, keep out of basements and other low areas. Stay out until

reghters declare them to be safe.

• Use your neighbor's phone and call a trained Propane Gas

service person and the re department. Even though you may

not continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and reghters check for escaped

gas. Have them air out the area before you return. Properly

trained Propane Gas service people should repair the leak,

then check and relight the gas appliance for you.

SOME POINTS TO REMEMBER

NO ODOR DETECTED - ODOR FADE

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the Propane Gas.

That's your signal to go into immediate action!

SAFETY INFORMATION FOR USERS OF PROPANE GAS

19563-9-0519 Page 5

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in whole

or in part for residential purposes, including those owned or

operated by the Commonwealth and where the side wall

exhaust vent termination is less than seven (7) feet above

nished grade in the area of the venting, including but not

limited to decks and porches, the following requirements

shall be satised:

INSTALLATION OF CARBON MONOXIDE DETEC-

TORS.

At the time of installation of the side wall horizontal

vented gas fueled equipment, the installing plumber or

gastter shall observe that a hard wired carbon monoxide

detector with an alarm and battery back-up is installed on

the oor level where the gas equipment is to be installed.

In addition, the installing plumber or gastter shall observe

that a battery operated or hard wired carbon monoxide

detector with an alarm is installed on each additional

level of the dwelling, building or structure served by the

side wall horizontal vented gas fueled equipment. It shall

be the responsibility of the property owner to secure the

services of qualied licensed professionals for the instal-

lation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an

attic, the hard wired carbon monoxide detector with

alarm and battery back-up may be installed on the

next adjacent oor level.

b. In the event that the requirements of this subdivision

can not be met at the time of completion of installa-

tion, the owner shall have a period of thirty (30) days

to comply with the above requirements; provided,

however, that during said thirty (30) day period, a

battery operated carbon monoxide detector with an

alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each

carbon monoxide detector as required in accordance with

the above provisions shall comply with NFPA 720 and

be ANSI/UL 2034 listed and IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be

permanently mounted to the exterior of the building at

a minimum height of eight (8) feet above grade directly

in line with the exhaust vent terminal for the horizontally

vented gas fueled heating appliance or equipment. The

sign shall read, in print size no less than one-half (1/2)

inch in size,    

CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the

side wall horizontally vented gas fueled equipment shall

not approve the installation unless, upon inspection,

the inspector observes carbon monoxide detectors and

signage installed in accordance with the provisions of 24

8 5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt

from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the

most current edition of NFPA 54 as adopted by

the Board; and

2. Product Approved side wall horizontally vented

gas fueled equipment installed in a room or

structure separate from the dwelling, building or

structure used in whole or in part for residential

purposes.

MENT VENTING SYSTEM PROVIDED. When the

manufacturer of Product Approved side wall hori-

zontally vented gas equipment provides a venting

system design or venting system components with

the equipment, the instructions provided by the

manufacturer for installation of the equipment and

the venting system shall include:

1. Detailed instructions for the installation of the

venting system design or the venting system

components; and

2. A complete parts list for the venting system design

or venting system.

(e) A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled

equipment, all venting instructions, all parts lists for

venting instructions, and/or all venting design instruc-

tions shall remain with the appliance or equipment

at the completion of the installation.

19563-9-0519Page 6

Introduction

Always consult your local Building Department regarding

regulations, codes or ordinances which apply to the installation

of a direct vent wall furnace.

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer should show owner how to start and operate

furnace and thermostat.

3. Installer must locate unit near a grounded wall receptacle

for 115VAC power and must provide gas supply and vent

the unit properly for safe operation.

WARNING

Any change to this furnace or its control can be

dangerous. This is a heating appliance and any panel,

door or guard removed for servicing an appliance must

be replaced prior to operating the appliance.

General Information

This series is design certied in accordance with American

National Standard / CSA Standard Z21.86 and CSA 2.32 by the

Canadian Standards Association as a Fan Type Direct Vent

Wall Furnace to be installed according to these instructions.

Any alteration of the original design, installed other than

as shown in these instructions or use with a type of gas

not shown on the rating plate is the responsibility of the

person and company making the change.

Important

All correspondence should refer to complete Model Number,

Serial Number and type of gas.

NOTICE: During initial ring of this unit, oil from the heat

exchanger may bake out and smoke may occur. To prevent

triggering of smoke alarms, ventilate the room in which the

unit is installed.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be

installed so that all burners and burner ignition devices are

located not less than 18" (457mm) above the oor.

Such equipment shall be located, or protected, so it is not

subject to physical damage by a moving vehicle.



Installation and replacement of gas piping, gas utilization

equipment or accessories and repair and servicing of

equipment shall be performed only by a qualied agency. The

term "qualied agency" means any individual, rm, corporation

or company which either in person or through a representative

is engaged in and is responsible for (a) the installation or

replacement of gas piping or (b) the connection, installation,

repair or servicing of equipment, who is experienced in such

work, familiar with all precautions required and has complied

with all the requirements of the authority having jurisdiction.

Commonwealth of Massachusetts: The installation

must be made by a licensed plumber or gas tter in the

Commonwealth of Massachusetts.

The installation must conform with local codes, or in the

absence of local codes, the National Fuel Gas Code, ANSI

Z223.1/NFPA 54 or Natural Gas and Propane Installation

Code, CSA B149.1.

*Available from the American National Standards Institute,

Inc., 11 West 42nd St., New York, NY 10036.

A manufactured home (USA only) or mobile home OEM

installation must conform with the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280,

or, when such a standard is not applicable, the Standard

for Manufactured Home Installations, ANSI Z225.1, or

Standard for Gas Equipped Recreational Vehicles and

Mobile Housing, CSA Z240.4.

High Altitudes

For altitudes/elevations above 2,000 feet (610m), input

ratings should be reduced at the rate of 4 percent for each

1,000 feet (305m) above sea level, this may be accomplished

by reducing manifold pressure. The maximum allowable

reduction in manifold pressure for Natural Gas shall be from

3.5" w.c. (.872kPa) to 2.8" w.c. (.697kPa). The maximum

allowable reduction in manifold pressure for Propane Gas

shall be from 10.0" w.c. (2.49kPa) to 8.0" w.c. (1.99kPa). For

Canadian high altitude applications, this appliance is suitable

for installation at elevations between 0 feet (0m) and 4,500

feet (1,372m) without change.

INTRODUCTION

19563-9-0519 Page 7

Model DV-55E

Input BTU/HR (KW/H) 55,000 (16.1)

Height 26" (660mm)

Width 37" (940mm)

Depths with Shroud 15 3/4" (400mm)

Gas Inlet (Pipe) 1/2" (13mm)

Electrical - Unit has a 5' (1.5m) 3 pronged cordset for

connection to an approved 115 VAC 60HZ

minimum AMPs - 5A wall receptacle.

Accessories for DV-55E Furnaces

Extended Vent Terminal

For walls up to 32"

(813mm)

DVT-2

Floor Pad DVP-1

SPECIFICATIONS

INTRODUCTION (CONT'D)



Model Number Description Used On

DV1153 Propane to Natural DV55E-5LPG

DV1152 Natural to Propane DV55E-5NAT

When an existing Category 1 heater is removed or replaced,

the original venting system may no longer be sized to

properly vent the attached appliances. Instructions shall

also indicate effects of an improperly sized venting system

(formation of condensate, leakage, spillage, etc.) and shall

specify the following test procedure:

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each

appliance connected to the venting system being

placed into operation could result in carbon monoxide

poisoning or death.

The following steps shall be followed for each

appliance connected to the venting system being

placed into operation, while all other appliances

connected to the venting system are not in operation:

1. Seal any unused openings in the venting system.

2.        



Gas Code, ANSI Z223.1/NFPA 54 or the Natural

Gas and Propane Installation Code, CSA B149.1

and these instructions. Determine that there is no

blockage or restriction, leakage, corrosion and

      

condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which

the appliance(s) connected to the venting system

are located and other spaces of the building.

4. 

5. Turn on clothes dryers and any appliance not

connected to the venting system. Turn on any

exhaust fans, such as range hoods and bathroom

exhausts, so they are operating at maximum

speed. Do operate a summer exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the

thermostat so appliance is operating continuously.

7.       

appliances at the draft hood relief opening after 5



of a match or candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected

in accordance with National Fuel Gas Code, ANSI

Z223.1/NFPA 54 and/or Natural Gas and Propane

Installation Code, CSA B149.1.

9. After is has been determined that each appliance

connected

to the venting system properly vents

when tested as outlined above, return doors,

     

      

previous conditions of use.

19563-9-0519Page 8

Consult the current National Fuel Gas Code, ANSI Z223.1

CAN/CGA-B149 (.1 or .2) installation code.

Recommended Gas Pipe Diameter

Pipe

Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Natural Propane Natural Propane

0-10 feet

0-3 meters

1/2”

12.7mm

3/8”

9.5mm

1/2”

12.7mm

3/8”

9.5mm

10-40 feet

4-12 meters

1/2”

12.7mm

1/2”

12.7mm

5/8”

15.9mm

1/2”

12.7mm

40-100

feet 13-30

meters

1/2”

12.7mm

1/2”

12.7mm

3/4”

19mm

1/2”

12.7mm

100-150

feet 31-46

meters

3/4”

19mm

1/2”

12.7mm

7/8”

22.2mm

3/4”

19mm

NOTE: Never use plastic pipe. Check to conrm whether your

local codes allow copper tubing or galvanized.

NOTE: Since some municipalities have additional local

codes, it is always best to consult your local authority and

installation code.

The use of the following gas connectors is recommended:

— ANS Z21.24 Appliance Connectors of Corrugated Metal

Tubing and Fittings

— ANS Z21.45 Assembled Flexible Appliance Connectors

of Other Than All-Metal Construction

The above connectors may be used if acceptable by

the authority having jurisdiction. The Commonwealth of

Massachusetts requires that a exible appliance connector

cannot exceed three feet in length.

Figure 1

Installing a New Main Gas Shut-Off

Each appliance should have its own manual gas shut-off.

A manual main gas shut-off should be located in the vicinity

of the unit. Where none exists, or where its size or location

is not adequate, contact your local authorized installer for

installation or relocation.

Compounds used on threaded joints of gas piping shall be

resistant to the action of liqueed petroleum gases. The gas

lines must be checked for leaks by the installer. This should

be done with a soap solution watching for bubbles on all

exposed connections, and if unexposed, a pressure test

should be made.



must be disconnected from piping at inlet of control valve

and pipe capped or plugged for pressure test. Never



will sustain damage!

A gas valve and ground joint union should be installed in the

gas line upstream of the gas control to aid in servicing. It is

required by the National Fuel Gas Code that a drip line be

installed near the gas inlet. This should consist of a vertical

length of pipe tee connected into the gas line that is capped

on the bottom in which condensation and foreign particles

may collect.

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8"

(3mm) N.P.T. plugged tapping, accessible for test gauge

connection, must be placed immediately upstream of the

gas supply connection to the appliance.

2. The appliance and its individual shut-off valve must be

disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in

excess of 1/2 psig (3.5 kPa).

The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at

test pressures equal to or less than 1/2 psig (3.5 kPa).

Attention! If anyone of the procedures results in

pressures in excess of 1/2psig (14" w.c.) (3.5kPa) on the





Both Propane and Natural Gas valves have a built-in pressure

regulator in the gas valve. Natural Gas models will have a

manifold pressure approximately 3.5" w.c. (.872kPa) at the

valve outlet with the inlet pressure to the valve from a minimum

of 5.0" w.c. (1.245kPa) for the purpose of input adjustment to

a maximum of 10.5" w.c. (2.614kPa) Propane Gas models will

have a manifold pressure approximately 10.0" w.c. (2.49kPa)

at the valve outlet with the inlet pressure to the valve from

a minimum of 11.0" w.c. (2.739kPa) for the purpose of input

adjustment to a maxium of 13.0" w.c. (3.237kPa).

A 1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge

connection, is located on the outlet side of the gas control.

GAS SUPPLY

19563-9-0519 Page 9



and new gas conversion label are provided in conversion kit attached to manifold pipe.

1. Make sure gas supply to furnace is off prior to conversion and disconnect electrical power to unit.

2. Open brass union located between the gas valve and burner box. Re-

move the 4 mounting screws securing manifold plate to the burner box.

Remove the top 2 screws holding the burner box top in place and then

remove the 1 screw holding the end of the manifold pipe in place. Grasp

union and remove manifold pipe.

3. Remove (1) Natural Gas main burner orice marked 44 for DV-20E, (2)

Natural Gas main burner orices marked 44 for DV-40E or (3) Natural

Gas main burner orices marked 47 for DV-55E located in the manifold

pipe and replace with (1) Propane Gas main burner orice marked 55

for DV-20E, (2) Propane Gas main burner orices marked 55 for DV-40E

or (3) Propane Gas main burner orices marked 1.20mm for DV-55E

supplied in conversion kit.

4. Replace manifold pipe being sure to locate orice(s) in the end of the burner. Secure the manifold and top burner box cover in place

using the screws earlier removed. Reconnect the brass union.

5. Remove the vinyl cap and unscrew the gas control convertible regulator and reverse to Propane Gas side (red ring on regulator)

and screw back into place. Reattach vinyl cap. Refer to gure illustrating the gas valve.

6. Place Natural Gas main burner orice(s) in conversion kit. Attach conversion kit to manifold pipe. Attach new label to unit nameplate

indicating that the unit was converted to Propane Gas.

7. Turn on gas supply to furnace and check all gas connections for leaks with soap solution, watching for bubbles on all gas connec-

tions.

8. Turn on electrical power to unit and turn on furnace to verify proper operation. It may take several tries for ignition to completely

purge all the air from the gas line.

and new gas conversion label are provided in conversion kit attached to manifold pipe.

1. Make sure gas supply to furnace is off prior to conversion and disconnect electrical power to unit.

2. Open brass union located between the gas valve and burner box.

Remove the 4 mounting screws securing manifold plate to the burner

box. Remove the top 2 screws holding the burner box top in place and

then remove the 1 screw holding the end of the manifold pipe in place.

Grasp union and remove manifold pipe.

3. Remove (1) Propane Gas main burner orice marked 55 for DV-20E,

(2) Propane Gas main burner orices marked 55 for DV-40E or (3)

Propane Gas main burner orices marked 1.20mm for DV-55E located

in the manifold pipe and replace with (1) Natural Gas main burner orice

marked 44 for DV-20E, (2) Natural Gas main burner orices marked

44 for DV-40E or (3) Natural Gas main burner orices marked 47 for

DV-55E supplied in conversion kit.

4. Replace manifold pipe being sure to locate orice(s) in the end of the burner. Secure the manifold and top burner box cover in place

using the screws earlier removed. Reconnect the brass union.

5. Remove the vinyl cap and unscrew the gas control convertible regulator and reverse to Natural Gas side and screw back into place.

The red propane ring will be up just under the vinyl cap. Reattach vinyl cap. Refer to gure illustrating the gas valve.

6. Place Propane Gas main burner orice(s) in conversion kit. Attach conversion kit to manifold pipe. Attach new label to unit nameplate

indicating that the unit was converted to Natural Gas.

7. Turn on gas supply to furnace and check all gas connections for leaks with soap solution, watching for bubbles on all gas connec-

tions.

8. Turn on electrical power to unit and turn on furnace to verify proper operation. It may take several tries for ignition to completely

purge all the air from the gas line.

CONVERSION INSTRUCTIONS FROM PROPANE GAS TO NATURAL GAS

CONVERSION INSTRUCTIONS FROM NATURAL GAS TO PROPANE GAS

TOPVIEW

BACKEND VIEW

GASCONTROLLEVERSHOWN

IN "OFF"POSITION

OFF

CONVERTIBLE

REGULATOR

VINYLCAP

VINYL CAP

CONVERTIBLE

REGULATO R

GAS CONTROL LEVER SHOWN

IN "OFF" POSITION

TOP VIEW

BACK END VIEW

GAS VALVE-NATURAL

TOPVIEW

BACKEND VIEW

GASCONTROLLEVERSHOWN

IN "OFF"POSITION

OFF

CONVERTIBLE

REGULATOR

VINYLCAP

VINYL CAP

CONVERTIBLE

REGULATO R

GAS CONTROL LEVER SHOWN

IN "OFF" POSITION

TOP VIEW

BACK END VIEW

GAS VALVE-PROPANE

GAS CONVERSION INSTRUCTIONS

19563-9-0519Page 10

1. Pick a location on a wall with a clear space of 36" (91.4cm)

high by 43" (109cm) wide in the room. In selecting

a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper

installation. Be sure to locate the unit close enough to a

115 VAC wall receptacle to properly power appliance.

2. Unit is supported by a wall bracket secured to the wall.

3. When facing the front of the furnace the minimum

clearances from casing to combustible construction are

10" (254mm) on top, 3" (76mm) on each side, recommend

18" (457mm) on right side for servicing and 0" (0mm) from

the oor and 0" (0mm) to rear wall.

4. The minimum distance from the center of the vent cap to

the nearest outside corner or obstruction is 12" (305mm).

5. The minimum wall depth is 2" (51mm) and the maximum

is 10"(254mm) [or 32"(813mm) using the extended

vent terminal kit accessory]. The use of vent tubes not

supplied by the manufacturer may result in unsatisfactory

performance.

The vent terminal of a direct vent appliance, with an input

of 50,000 BTU (14.6KW) per hour or more shall be located

at least 12" (305mm) from any opening through which ue

gases could enter a building.

The bottom of the exhaust vent terminal and the air intake

shall be located at least 12" (305mm) above grade and must

be vented outside.

WARNING: The nearest point of the vent cap should be



any pressure regulator. In case of regulator malfunction,

the six (6) feet (1.83m) distance will reduce the chance

of gas entering the vent cap.

Installation on Rugs and Tile

If this appliance is to be installed directly on carpeting, tile,

or other combustible material, other than wood ooring, the

appliance shall be installed on a metal or wood panel extend-

ing the full width and depth of the appliance.

The base referred to above does not mean the re-proof

base as used on wood stoves. The protection is primarily

for rugs that may be extremely thick and light-color tile that

can discolor.

Locating Wall Opening (Figures 2, 3 and 4)

This furnace must be installed on an outside wall. Locate

wall studs so that wall vent opening will be located between

wall studs. The wall studs can be used for attachment of wall

mounting bracket. The wall opening required for venting is a

3 1/4" (83mm) diameter opening.

Refer to Figures 2 and 3 for positioning the furnace on

wall and for locating gas line connection and vent opening.

Furnace can sit on the oor and should be secured to the

wall through the wall bracket secured to the rear top shroud.

Figure 2

Figure 3

(76mm)

8 3/4"

(222mm)

12 5/16"

20" (508mm)

(313 mm)

(267mm)

10 1/2"

1/2" (13mm) DIA.

GAS SUPPLY

WALL

MAYBE20" TO 13"

TO AVOID STUD

31/4"(83mm) DIA. VENT

HOLE THRU OUTSIDE WALL

17 11/16"

(449mm)

FLOOR TO

BOTTOM OF

WALL BRACKET

FRONT OF FURNACE

CLEARANCES

FURNACE INSTALLATION

19563-9-0519 Page 11

Figure 4

Installing Wall Bracket (Figures 5 and 6)

After nding a location for the furnace, gas supply and vent,

the wall bracket must be positioned and installed. The bracket

should be mounted to the wall studs, if possible, or anchored

solidly to the wall. Use the (2) 10 x 1 1/2" (38mm) hex-head

screws or (2) plastic anchors provided. Drill (2) 5/16" (8mm)

diameter holes in wall if plastic anchors are used. Attach the

two wall mounting brackets to the casing back by using (4)

10 x 1/2" (13mm) hex-head screws provided.

Figure 5

Figure 6

Figure 7

Figure 8

2" (51mm) TO 13" (330mm)

2" (51mm) TO 32" (813mm)

WALL

CASING

BACK

#10X1"

WALL MOUNTING BRACKET

WALL

BRACKET

#10X1/2"

4" (102mm)

WALL

INTAKE FLEX HOSE

WITH CLAMPS

EXHAUST

INTAKE AIR

MOUNTING PLATE

EXHAUST ELBOW MAY

BE CUT TO LENGTH

TO FIT VENT BOX.

SECURE IN PLACE

USING HOSE CLAMPS

PROVIDED.

KEEP CAP ON

UN-USED AIR

INTAKE OPENING

EXHAUST AIR

ORANGE SILICONE

ELBOW CONNECTOR

INTAKE AIR

BLACK FLEXIBLE HOSE

19563-9-0519Page 12

Venting (Figures 7 and 8)

This unit is vented directly out the back using the concentric

vent tube assembly provided. See Figure 2 for vent hole

location. This hole location can be conveniently moved closer

to unit exhaust outlet tube to avoid wall stud interference if

necessary. The orange silicone exhaust elbow would need

to be cut to length. Do not locate vent directly behind the

exhaust outlet.

The vent provided will accommodate walls up to 10" thick

and can be cut shorter for thinner walls if desired by using a

hacksaw or cut-off saw. Be sure to leave the minimum 3/4"

of tube length extending beyond the outside wall plate. Both

the inner and outer tube will be cut to the same length as the

inner exhaust tube has an extension piece which is added

during nal outside assembly.

Be sure to deburr the ends with a le after cutting. Installation

is easy after cutting the wall opening secure the vent terminal

box in place using the (4) 10 x 1" hex-head screws provided.

Locate the box so that the middle exhaust tube is directed

toward the furnace exhaust outlet opening. See Figure 8.

Attach the black 2" exible inlet air hose to the bottom 2"

connector on the vent box using a hose clamp. Secure the

other end to the lower inlet air box connector using the hose

clamp. Do not kink hose. Attach the long straight end of the

2" orange silicone exhaust elbow to the middle vent terminal

tube and rotate the elbow toward the furnace exhaust outlet.

Secure the hose to the vent box using a hose clamp. Carefully

push the furnace back closer to the wall and secure the

exhaust elbow to the 2" exhaust tube exiting the unit. Secure

the elbow in place using the last remaining hose clamp. The

furnace can now be secured to the wall.

For wall depths thicker than 10" (254mm) order the extended

vent terminal kit which will cover walls to 32" (813mm)

thickness. The vent pipes must be cut to length to assemble

for desired wall thickness. Do not extend venting beyond the

32" maximum length.

Installation of Shroud

To complete inside installation, secure furnace to the wall

bracket by attaching the two wall mounting brackets to the

wall bracket by using (2) 10 x 1/2" (13mm) hex-head screws

provided (See Figures 4 and 6). To attach the right shroud

and left shroud to the casing back, the 3/4" wide ange on

the shroud must be positioned toward the casing side. When

positioned correctly, the (6) louvers on the shroud will be facing

up and the knock-out on the shroud will be facing down. Attach

the right shroud and left shroud to the casing back with (3)

10 x 1/2" hex-head screws supplied in hardware package,

for each shroud. Attach top shroud to right shroud and left

shroud with (4) Phillips-head screws, supplied in hardware

package. Insert air lter into top shroud.

Attention: If the right shroud and left shroud are installed

incorrectly, with the 3/4" wide anges facing inward, the top

shroud will not be able to be installed onto the side shrouds.

The top shroud will appear to be 2 inches, too narrow.

Vent Terminal (Figure 9)

Place the 6 3/8" x 6 3/8" (162mm x 162mm) black foam,

wall plate gasket within the mounting plate. The 4 3/4"

(121mm) diameter hole in the black foam gasket will allow

for installation of the concentric vent tube assembly. Slide the

outside mounting plate into place on the concentric vent tube

assembly. The outside mounting plate should seal against the

face of the building and be secured in place using (4) 10 x 1"

hex-head screws. Be sure to caulk and seal around the pipe

on the exterior using high temperature exterior grade, silicone

caulk rated at 204°C/400°F. Wipe some silicone sealant on

the 2" (51mm) exhaust pipe extension. The end cap can be

pushed into place on the exhaust outlet tube.

Attention: The opening on the bottom of the end cap must

be positioned toward the ground. The opening on the bottom

cannot be pivoted to the right or left, it must be centered

toward the ground.

Figure 9

Reassembly and Resealing Vent-Air Intake System

When vent-air intake system is removed for servicing the

furnace, the following steps will assure proper reassembly

and resealing of the vent-air intake assembly. Be sure all

hose connections are re-secured in place using the hose

clamps removed. Reattach all screws securing mounting

anges and inspect all connections for a tight t. Use high

temperature silicone caulk rated at 204°C/400°F to reseal

the inlet air vent pipe to the mounting plate.

NO. 10X11/2"

SCREWS (4)

INLETAIR

EXHAUST

AIR

12"(305mm)MIN.

ABOVE GRADE

CAULK AROUND PIPE

EXHAUST FITTING-SLIDE ONTO

2" EXHAUST TUBE AND USE RTV

SEALANT TO SECURE IN PLACE

WITH OUTLET POINTED DOWN

AS SHOWN

FURNACE INSTALLATION (CONT'D)

19563-9-0519 Page 13

FOR YOUR SAFETY READ BEFORE OPERATING

A. This appliance does not have a pilot. It is equipped with

an ignition device which automatically lights the burner.

Do not try to light the burner by hand.

B. BEFORE OPERATING smell all around the appliance

area for gas. Be sure to smell next to the oor because

some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neigh-

bor's phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the re

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or

turn by hand, don't try to repair it; call a qualied service

technician. Force or attempted repair may result in a

re or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualied service technician

to inspect the appliance and to replace any part of the

control system and any gas control which has been

under water.

1. STOP! Read the safety information above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. This appliance is equipped with an ignition device which

automatically lights the burner. Do not try to light the

burner by hand.

5. Remove control access panel (front panel).

6. Turn gas control knob clockwise to "OFF."

7. Wait ten (10) minutes to clear out any gas. Then smell

for gas, including near the oor. If you smell gas, STOP!

Follow "B" in the safety information above. If you don't

smell gas, go to the next step.

8. Turn gas control knob counterclockwise to

"ON".

9. Replace control access panel (front panel).

10. Turn on all electric power to the appliance.

11. Set thermostat to desired setting.

12. If the appliance will not operate, follow the instructions

"TO TURN OFF GAS TO APPLIANCE" and call your

service technician or gas supplier.

OPERATING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to lowest setting.

2. Turn off all electric power to the appliance if service is

to be performed .

3. Remove control access panel (front panel).

4. Turn gas control knob clockwise

to "OFF." Do

not force.

5. Replace control access panel (front panel).

TOPVIEW

BACKEND VIEW

GASCONTROLLEVERSHOWN

IN "OFF"POSITION

OFF

CONVERTIBLE

REGULATOR

VINYLCAP

VINYL CAP

CONVERTIBLE

REGULATOR

GAS CONTROL LEVER SHOWN

IN "OFF" POSITION

TOP VIEW

BACK END VIEW

LIGHTING INSTRUCTIONS

WARNING



personal injury or loss of life.

19563-9-0519Page 14

The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical

Code, CSA C22.1, if an external electrical source is utilized.

This





directly into a properly grounded three-prong receptacle. Do

not cut or remove the grounding prong from this plug. For an

ungrounded receptacle, an adapter, which has two prongs and a

wire for grounding, can be purchased, plugged into the ungrounded

receptacle and its wire connected to the receptacle mounting screw.

With this wire completing the ground, the appliance cord plug can

be plugged into the adapter and be electrically grounded.

CAUTION: Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

NOTE: For testing ame sensor circuit use a micro-amp meter in

series with sensor. Minimum current should be 1 micro-amp during

operation. Be careful as ame sensor is in the 115VAC circuit. If

current is below 1 micro-amp, remove sensor, clean with light

sandpaper and retest.

NOTE: This heater is equipped with a remote bulb electronic

thermistor control located down low at the back of the furnace.

Sometimes due to eld locations different air currents may effect the

control sensing of the thermistor. This sensing bulb can be re-located

if necessary to provided for better room air sensing and control.

Replacement of Thermistor with 24 Volt Wall Thermostat

1. If furnace is installed, turn off gas supply and electric supply.

2. Remove casing front.

3. Remove black hose from front nipple on pressure switch.

4. Remove junction box cover (4 screws).

5. Please refer to wiring diagram for removal of the following

wires.

Internal Electronic Thermostat/Temperature Control Board

Attention! No 24 volt wall thermostat wires are to be

attached to the internal electronic thermostat.

7. Control Board

A. Remove white wire form screw marked W.

B. Remove yellow wire from screw marked C.

C. Remove red wire from screw marked R.

8. Route (2) wires from any 24 volt wall thermostat through the

casing back of furnace to the screws marked W and R on

the control board.

9. Replace junction box cover (4 screws).

10. Replace black hose onto front nipple on pressure switch.

11. Replacement of thermistor with 24 volt wall thermostat is

completed.

CIRCULATING AIR BLOWER

WHT

RED

YEL

RED

BLK

PUR

INDUCER

BLOWER

BLU

IF ANYOFTHE ORIGINAL WIRE AS SUPPLIED WITH THE

APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED

WITHAWIRE OF AT LEAST 105

C TEMPERATURE RATING.

LIMIT SWITCH

SECONDARY

FIELD INSTALLED

THERMOSTAT

24 VOLT

115VAC

SWITCH

LIMIT

3A FUSE

GND

BLACK

WHITE

ON/OFF

ROLLOUT

PRESSURE

SWITCH

R-8191

VALVE

GAS

TRANSFORMER

24 VAC

PRIMARY115 VAC

COMMON

DISCONNECT INTEGRAL THERMOSTAT "R", "W", AND "C" LEADS AND ATTACH WALL THERMOSTAT AS SHOWN

PSROS

RED

GRN

ORG

ELECTRONIC

THERMOSTAT

INTEGRAL

WHT

YEL

RED

GRY

BRN

GRY

24 V

WHT

BLK

115 V

OPTIONAL WALL MOUNT THERMOSTAT

XFMR

ON/OFF

BLACK NEUTRAL

RIBBED

INSULATION

BLACK HOT

SMOOTH

INSULATION

CIRCULATING AIR

BLOWER MOTOR

RED LED

STATUS

LIGHT

IGN

HOT SURFACE

IGNITOR

POWER SWITCH

INDUCER MOTOR

FLAME SENSOR

COMBUSTION AIR

ROS = ROLLOUT LIMIT SWITCH

IGN = HOT SURFACE IGNITOR

PS=PRESSURE SWITCH

XFMR=TRANSFORMER

CORDSET 115VAC

FS=FLAME SENSOR

GV=GAS VALVE

LS=LIMIT SWITCH

4 1

WIRING

19563-9-0519 Page 15

Proper Main Burner Flame

The proper main burner ame will be a blue primary (inner)

ame with a larger, lighter blue secondary (outer) blue ame.

Figure 10

Cleaning Main Burner(s)

Remove main burner(s) and apply air pressure inside the

throat and ports of the main burner(s).

Removing Main Burner(s)

1. Remove front grill assembly.

2. Remove burner compartment access panel (2 screws).

3. Remove main burner(s) from burner compartment (2

screws per main burner).

Removing Gas Valve

1. Remove front grill assembly.

2. Disconnect manifold union assembly at gas valve.

3. Remove (2) two 24 volt wires from gas valve. Label wires

prior to disconnection from gas valve.

4. Remove gas valve from gas valve bracket.



1. Remove front grill assembly.

2. Remove burner compartment access panel (2 screws).

3. Disconnect manifold union assembly.

4. Disconnect manifold union assembly brackets (5 screws).

Removing Ignitor and Flame Sensor

1. Remove front grill assembly.

2. Remove ignitor from burner compartment (2 screws).

3. Remove ame sensor from burner compartment (1 screw).

Cleaning Combustion (Exchanger) Assembly

A QUALIFIED SERVICE PERSON should remove the

combustion (exchanger) assembly. Apply air pressure to

the inside of the combustion (exchanger) assembly in order

to clear all passageways.

Oiling

The blower motor has an oil hole located on each end of the

motor. Use #20 motor oil only. It is best to oil the motor

several times during the heating season using 2 or 3 drops

MAINTENANCE

19563-9-0519Page 16

Your new furnace should provide many years of trouble free

performance, however, a yearly inspection of the burners ,

ue passageways and the outlet vent assembly should be

done. Be sure all passageways are open and clear of any

obstruction, or soot build up. Be sure to shut off all power to

the unit while performing this inspection.

Periodically remove the circulating air lter and clean with

water to remove all dirt. Shake dry and reinstall in unit.

System Operation

1. This furnace has an electronic thermostat and control

board to monitor the room temperature and then control

the furnace operation to provide the best comfort and

performance from a heating appliance. To operate unit

turn ON/OFF switch to ON and then turn temperature

control knob clockwise slowly till furnace turns on. For

typical room comfort, the control knob should be pointed

toward medium.

2. The furnace control board follows sequence of operation

which allows for self diagnosis in the event there is a

problem. The control then blinks a status light, a set number

of blinks based on what problem has been encountered.

When the furnace is on and there is a no fault condition,

the red LED is on.

On a typical call for heat by the integral thermostat 24

VAC is applied to the W terminal on the board.

The inducer blower circuit is energized and the inducer

blower comes on for 15 seconds pre-purging out any gas

and closing the pressure switch.

The hot surface ignitor is energized and after a 17 second

warm-up, the gas valve circuit is energized, opening the

gas valve and igniting the burners. After burning for about

30 seconds, the circulating air blower comes on, delivering

warm air to the room. If ignition does not occur, the ignition

sequence is repeated again up to 2 more times. (3 trials

for ignition-total)

3. After the furnace operates and satises the thermostat, the

gas valve closes and the circulating air blower continues

to run for about 2 minutes and then shuts off. The inducer

blower runs for 5 seconds and shuts off.

If for any reason ignition and operation does not occur, the

control board will blink the red fault status LED, a sequence

code, indicating what to look for as a troubleshooting guide.

If the red LED is ON but not blinking check the electronic

temperature control to verify its operation. This can be

easily done by disconnecting the 3 electronic temperature

control leads from the main furnace board and using a

pig tail jumper to connect R & W together on the board. If

the furnace comes on and runs normally the temperature

control board is malfunctioning. If the heater still does not

come on, then the main furnace board is malfunctioning.

Look for any fault codes below and verify the 3 amp fuse

is not blown.

OPERATION AND TROUBLESHOOTING

19563-9-0519 Page 17

FURNACE CONTROL BOARD DIAGNOSTICS

FAULT SEQUENCE CODE — Trouble Shooting Guide

 FAULT CONDITION FAULT CORRECTION

Steady On 

1 Flash Temperature limit switch is open

-Check Circulating Air Blower Inlet or Grill Outlet for Blockage,

Inducer Blower/Circulating Air Blower Run to Cool Heat Ex-

changer and Limit

-Check for Flame Roll Out Condition Causing Roll Out Limit

Switch on Burner Box to Open

-Clean Circulating Air Filter

2 Flashes

Pressure switch is open with in-

ducer on

-Check Heat Exchanger and Flue System, Outlet and Inlet for

Restriction

-Check Inducer Blower/Wheel for Operation/Airow

-Check Pressure Switch

3 Flashes

Pressure switch is closed with

inducer off

-Check Pressure Switch and Replace

4 Flashes Lockout due to failed ignition

-Check for Broken Ignitor

-Check for Bent Ignitor Bracket - Ignitor too far from Burner

-Check for Flame Sensor Malfunction/or False Ground

-Check Gas Valve

-Reset Thermostat

5 ashes

L1/Neutral reversed or voltage not

present on L1

-Shut Off Power to Unit and Dis-Connect Cordset Plug from Wall

Receptacle.

Open Junction Box and Un-Reverse Polarity of Incoming Power

Leads

Rapid Flash

Flame sense or internal control

fault

-Check Ignitor Operation

-Check Flame Sensor for Malfunction or False Grounding

-Check Gas Valve

-Reset Thermostat

NOTE: If the hot surface ignitor is to be replaced, be sure to disconnect all power to the unit. Be very careful in handling

the new ignitor as they are fragile and can be broken easily if hit or dropped.

19563-9-0519Page 18

Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through

the distributor. Parts can be shipped directly to the service person/dealer.

All parts listed in the Parts List have a Part Number. When ordering parts, rst obtain the Model Number from the name plate on your

equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate il-

lustration and list. Be sure to give all this information.

Furnace Model Number

Part Description

Furnace Serial Number Part Number

Type of Gas (Propane or Natural)

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.

Shipments contingent upon strikes, res and all causes beyond our control.

Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, IL 62222-0529

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

HOW TO ORDER REPAIR PARTS

PARTS LIST

INDEX

NO.

PART

NO.

DESCRIPTION

1 DV-1378 SHROUD TOP

2 DV-1376 SHROUD SIDE RIGHT

3 R-2521 AIR FILTER

4 DV-1375 FILTER RETAINER

5 DV-1379 WALL MOUNTING BRACKET

6 DV-1048 WALL BRACKET - 2 REQ

7 R-2586 CONTROL DOOR PIN - 2 REQ

8 19676 CONTROL DOOR ASSEMBLY

9 DV-1373 CASING TOP

10 R-2661 BLOWER HOUSING - 2 REQUIRED

11 R-2663 BLOWER WHEEL - 2 REQ

12 R-2662 BLOWER MOTOR

13 R-2598 MOTOR BASE WASHER - 4 REQ

14 R-1279 LIMIT SWITCH

15 DV-1367 INNER TOP

16 R-2546 CONTROL KNOB

17 R-2522 ON/OFF SWITCH

18 19561 JUNCTION BOX

19 DV-1370 JUNCTION BOX COVER

20 R-1995 TRANSFORMER

21 R-6988 PRESSURE SWITCH

22 R-8140 CONTROL BOARD

23 R-2577A TEMPERATURE CONTROL BOARD

24 DV-1365 CASING WELDED ASSEMBLY

25 R-1468 STRAIN RELIEF BUSHING

26 R-2099 CORD SET

27 DV-1371 INNER END

28 DV-1372 CASING SIDE - 2 REQUIRED

29 DV-1163 COLLECTOR BOX

30 R-2519 INDUCER WHEEL

31 DV-1169 INDUCER BLOWER HOUSING ASSEMBLY

32 R-2523 INDUCER MOTOR

33 15785 EXCHANGER ASSEMBLY

34 27523 IGNITOR KIT

37 R-2543 FLAME SENSOR

38 R-12593 BURNER - 3 REQ

39 R-2575 FLAME ROLLOUT SWITCH

40 DV-1038 BURNER COMPARTMENT ACCESS PANEL

41 DV-1143 BURNER COMPARTMENT

42 R-3237 GAS VALVE - NATURAL

42 R-3238 GAS VALVE - PROPANE

43 DV-1366 VALVE BRACKET

44 DV-1147 MANIFOLD ASSEMBLY

45 P-88-1.20MM ORIFICE (PROPANE GAS) - 3 REQ

45 P-88-47 ORIFICE (NATURAL GAS) - 3 REQ

46 M-148 MANIFOLD GASKET

47 DV-781 OBSERVATION HOLE COVER ASSEMBLY

48 M-155 OBSERVATION HOLE COVER GASKET

49 15792 FRONT SHIELD ASSEMBLY

50 DV-1024 BOTTOM SHIELD

51 DV-1364 FRONT GRILL ASSEMBLY

52 DV-1380 CASING FRONT ASSEMBLY

53 R-2539 HOSE CLAMP - 4 REQ

54 R-3113 INLET HOSE

55 R-3111 OUTLET ELBOW

56 DV-1192 VENT PAN ASSEMBLY

57 R-3114 INLET CAP

58 R-3115 WALL PLATE GASKET - INSIDE

59 R-2587 WALL PLATE GASKET - OUTSIDE

60 DV-1195 WALL PLATE - OUTSIDE

61 DV-1193 TUBE SPACER

62 DV-1194 END CAP ASSEMBLY

63 DV-1377 SHROUD SIDE LEFT

NS R-8142

WIRE ASSEMBLY - CONTROL BOARD 5 PIN

NS R-2563

WIRE ASSEMBLY - CONTROL BOARD 9 PIN

INDEX

NO.

PART

NO.

DESCRIPTION

19563-9-0519 Page 19

PARTS VIEW

19563-9-0519Page 20

www.empirecomfort.com

Empire Comfort Systems Inc.

Belleville, IL

If you have a general question

about our products, please e-mail

us at [email protected].

If you have a service or repair

question, please contact your dealer.

WARRANTY

Empire Comfort Systems Inc. warranties this space heating product to be free from defects at the time of purchase and for the periods

specied below. Space heating products must be installed by a qualied technician and must be maintained and operated safely, in

accordance with the instructions in the owner’s manual. This warranty applies to the original purchaser only and is not transferable.

All warranty repairs must be accomplished by a qualied gas appliance technician.

Limited Ten-Year Parts Warranty – Combustion Chamber

Empire promises to the owner that if the combustion chamber (see parts list) fails because of defective workmanship or

material with ten years from the date of purchase, Empire will repair or replace at Empire’s option.

Limited One-Year Parts Warranty – Remote Controls, Thermostats, Accessories, and Parts

Should any remote control, thermostat, accessory, or other part fail because of defective workmanship within one year from

the date of purchase, Empire will repair or replace at Empire’s option.

Duties Of The Owner

The appliance must be installed by a qualied installer and operated in accordance with the instructions furnished with the

`appliance. A bill of sale, cancelled check, or payment record should be kept to verify purchase date and establish

warranty period. Ready access to the appliance for service.

What Is Not Covered

Damages that might result from the use, misuse, or improper installation of this appliance.

Travel, diagnostic costs and freight charges on warranted parts to and from the factory.

Claims that do not involve defective workmanship or materials.

Unauthorized service or parts replacements.

Removal and reinstallation cost.

Inoperable due to improper or lack of maintenance.

How To Get Service

To make a claim under this warranty, please have your receipt available and contact your installing dealer. Provide the dealer

with the model number, serial number, type of gas, and purchase verication. The installing dealer is responsible for providing

service and will contact the factory to initiate any warranted parts replacements. Empire will make replacement parts available

at the factory. Shipping expenses are not covered.

If, after contacting your Empire dealer, service received has not been satisfactory, contact: Consumer Relations Department,

Empire Comfort Systems Inc., PO Box 529, Belleville, Illinois 62222, or send an e-mail to [email protected] with

“Consumer Relations” in the subject line.

Your Rights Under State Law

This warranty gives your specic legal rights, and you may also have other rights, which vary from state to state.

La page charge ...

Empire Heating Systems DV55E Le manuel du propriétaire

Marque: Empire Heating Systems

Modèle: DV55E

Taper: Le manuel du propriétaire

Ce manuel convient également à

High-Efficiency Direct-Vent Wall Furnace (DV55E)

Télécharger le PDF

rapport

dans d''autres langues

English: Empire Heating Systems DV55E Owner's manual

Empire Heating Systems DV55E Le manuel du propriétaire

Ce manuel convient également à

Empire Heating Systems DV55E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents