Empire Heating Systems High-Efficiency Wall Furnace (DV20E, DV40E) Le manuel du propriétaire

Marque: Empire Heating Systems

Modèle: High-Efficiency Wall Furnace (DV20E, DV40E)

Taper: Le manuel du propriétaire

Ce manuel convient également à

Page 1

Patent # 5.664.555

This appliance may be installed as an OEM

installation in a manufactured home (USA

only) or mobile home and must be installed

in accordance with the manufacturer's in-

structions and the Manufactured Home Con-

struction and Safety Standard, Title 24 CFR,

Part 3280, in the United States, or the Mobile

Home Standard, CAN/CSA Z240 MH Series,

in Canada.

This appliance is only for use with the type(s)

of gas indicated on the rating plate. A conver-

sion kit is supplied with the appliance.

FAN TYPE

DIRECT VENT

WALL FURNACE

For Installation In

Manufactured (Mobile Home),

Modular Or Residential Homes

MODELS

DV-20E-5

DV-40E-5

WARNING

FIRE OR EXPLOSION HAZARD

If the information in these instructions is

not followed exactly, a re or explosion

may result causing property damage,

personal injury or loss of life.

— Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

— Installation and service must be

performed by a qualied installer,

service agency or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

WARNING

If not installed, operated and maintained in

accordance with the manufacturer's instructions,

this product could expose you to substances in

fuel or from fuel combustion which can cause

death or serious illness.

INSTALLATION INSTRUCTIONS

AND OWNER'S MANUAL

19562-8-0919Page 2

TABLE OF CONTENTS

SECTION PAGE

Important Safety Information ..................................................................................................................................... 3

Safety Information for Users of Propane Gas ........................................................................................................... 4

Requirements for Massachusetts ............................................................................................................................. 5

Introduction ............................................................................................................................................................ 6-7

 ............................................................................................................................................................ 7

Gas Supply ............................................................................................................................................................... 8

Gas Conversion Instructions ..................................................................................................................................... 9

Clearances .............................................................................................................................................................. 10

Furnace Installation ............................................................................................................................................ 11-13

Lighting Instructions ............................................................................................................................................... 14

Wiring ...................................................................................................................................................................... 15

Maintenance ........................................................................................................................................................... 16

Operation and Troubleshooting ............................................................................................................................... 16

Furnace Control Board Diagnostics ........................................................................................................................ 17

How to Order Repair Parts ...................................................................................................................................... 17

Parts List ................................................................................................................................................................ 18

Parts View ............................................................................................................................................................... 19

Appliance Service History .................................................................................................................................. 20-21

Master Parts Distributor List .................................................................................................................................... 22

How To Order Repair Parts ..................................................................................................................................... 22

Warranty .................................................................................................................................................................. 23

19562-8-0919 Page 3

 



 

of high surface temperatures and should stay away to

avoid burns or clothing ignition.

   

they are in the same room as the appliance.

        

placed on or near the appliance.

        

an appliance must be replaced prior to operating the

appliance.

 

 



For manufactured home (USA only) or mobile home or

residential installation convertible for use with Natural



made for the simple conversion from one gas to the

other.

 Installation and repair should be done by a QUALIFIED

SERVICE PERSON. The appliance should be inspected



person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding materials, etc.

It is imperative that control compartments, burners and

circulating air passageways of the appliance be kept clean.

   put anything around the furnace that will



  keep the appliance area clear and free from

     

vapors and liquids.

  examine venting system periodically and replace

damaged parts.

 make a periodic visual check of burner. Clean and

replace damaged parts.

 use this heater if any part has been under



inspect the heater and to replace any part of the control

system and any gas control which has been under water.

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

IMPORTANT SAFETY INFORMATION

19562-8-0919Page 4

Some people cannot smell well. Some people cannot smell the



smell the odorant in propane. Smoking can decrease your ability

to smell. Being around an odor for a time can affect your sensitivity

or ability to detect that odor. Sometimes other odors in the area

mask the gas odor. People may not smell the gas odor or their

minds are on something else. Thinking about smelling a gas odor

can make it easier to smell.

The odorant in Propane Gas is colorless, and it can fade under

some circumstances. For example, if there is an underground leak,

-

ants in Propane Gas also are subject to oxidation. This fading can

occur if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That will

take some of the odorant out of the gas, reducing its odor intensity.

Propane Gas may stratify in a closed area, and the odor intensity

could vary at different levels. Since it is heavier than air, there may

be more odor at lower levels. Always be sensitive to the slightest

gas odor. If you detect any odor, treat it as a serious leak. Imme-

diately go into action as instructed earlier.





not know all the following safety precautions which can protect

both you and your family from an accident. Read them carefully

now, then review them point by point with the members of your

household. Someday when there may not be a minute to lose,

everyone's safety will depend on knowing exactly what to do. If,

after reading the following information, you feel you still need more

information, please contact your gas supplier.

 

Gas Dealer can give you a "Scratch and Sniff" pamphlet. Use



that your Propane Gas has a weak or abnormal odor, call your

Propane Gas Dealer.

 

or make adjustments to appliances on the Propane Gas system.



Gas prior to and while lighting pilot lights or performing service

or making adjustments.

        

smell that can cover up the Propane Gas odor. Do not try to

light pilot lights, perform service, or make adjustments in an

area where the conditions are such that you may not detect

the odor if there has been a leak of Propane Gas.

 

new cylinders and tanks, is possible. Therefore, people should

be particularly alert and careful when new tanks or cylinders

are placed in service. Odor fade can occur in new tanks, or





of service for a time may develop internal rust which will cause

odor fade. If such conditions are suspected to exist, a periodic

sniff test of the gas is advisable. If you have any question about

the gas odor, call your Propane Gas dealer. A periodic sniff test of

the Propane Gas is a good safety measure under any condition.

 

you think you should, assume you have a leak. Then take the

same immediate action recommended above for the occasion



 

no vapor pressure), turn the tank valve off immediately. If the

container valve is left on, the container may draw in some air



new internal rusting could occur. If the valve is left open, then

treat the container as a new tank. Always be sure your con-

tainer is under vapor pressure by turning it off at the container



completely empty.

 

Do not do anything that could ignite the gas.

 



 

 

such as basements. When you have reason to suspect a gas

leak, keep out of basements and other low areas. Stay out until



 



not continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

 

gas. Have them air out the area before you return. Properly

trained Propane Gas service people should repair the leak,

then check and relight the gas appliance for you.

SOME POINTS TO REMEMBER

NO ODOR DETECTED - ODOR FADE

PROPANE GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the Propane Gas.

That's your signal to go into immediate action!

SAFETY INFORMATION FOR USERS OF PROPANE GAS

19562-8-0919 Page 5

REQUIREMENTS FOR MASSACHUSETTS



installed in every dwelling, building or structure used in whole

or in part for residential purposes, including those owned or

operated by the Commonwealth and where the side wall

exhaust vent termination is less than seven (7) feet above



limited to decks and porches, the following requirements



INSTALLATION OF CARBON MONOXIDE

DETECTORS.

At the time of installation of the side wall

   

        

carbon monoxide detector with an alarm and battery

         

equipment is to be installed. In addition, the installing



or hard wired carbon monoxide detector with an alarm is

installed on each additional level of the dwelling, building

  

gas fueled equipment. It shall be the responsibility of



licensed professionals for the installation of hard wired

carbon monoxide detectors

  

fueled equipment is installed in a crawl space or an

attic, the hard wired carbon monoxide detector with

alarm and battery back-up may be installed on the



b. In the event that the requirements of this subdivision

can not be met at the time of completion of installa-

tion, the owner shall have a period of thirty (30) days

to comply with the above requirements; provided,

however, that during said thirty (30) day period, a

battery operated carbon monoxide detector with an

alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each

carbon monoxide detector as required in accordance with

the above provisions shall comply with NFPA 720 and



3. SIGNAGE

permanently mounted to the exterior of the building at

a minimum height of eight (8) feet above grade directly



vented gas fueled heating appliance or equipment. The



“GAS VENT DIRECTLY BELOW. KEEP

CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the



not approve the installation unless, upon inspection, the

inspector observes carbon monoxide detectors and sig-

nage installed in accordance with the provisions of 248

CMR 5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt



1. The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the

most current edition of NFPA 54 as adopted by

the Board; and

   

gas fueled equipment installed in a room or

structure separate from the dwelling, building or

structure used in whole or in part for residential

purposes.

MENT VENTING SYSTEM PROVIDED. When the

manufacturer of Product Approved side wall hori-



system design or venting system components with

the equipment, the instructions provided by the

manufacturer for installation of the equipment and



1. Detailed instructions for the installation of the

venting system design or the venting system

components; and

2. A complete parts list for the venting system design

or venting system.

(e) A copy of all installation instructions for all Product



equipment, all venting instructions, all parts lists for

venting instructions, and/or all venting design instruc-

tions shall remain with the appliance or equipment

at the completion of the installation.

19562-8-0919Page 6

Introduction

Always consult your local Building Department regarding regulations,

codes or ordinances which apply to the installation of a direct vent

wall furnace.

Instructions to Installer

Installer must leave instruction manual with owner after installation.

2. Installer should show owner how to start and operate furnace

and thermostat.

3. Installer must locate unit near a grounded wall receptacle for

115VAC power and must provide gas supply and vent the unit

properly for safe operation.

WARNING

Any change to this furnace or its control can be dangerous.

This is a heating appliance and any panel, door or guard

removed for servicing an appliance must be replaced prior

to operating the appliance.

General Information



Standard/CSA Standard Z21.86 and CSA 2.32 by the Canadian

Standards Association as a Fan Type Direct Vent Wall Furnace to

be installed according to these instructions.

Any alteration of the original design, installed other than as shown

in these instructions or use with a type of gas not shown on the

rating plate is the responsibility of the person and company making

the change.

Important

All correspondence should refer to complete Model Number, Serial

Number and type of gas.

Notice

may bake out and smoke may occur. To prevent triggering of smoke

alarms, ventilate the room in which the unit is installed.

Installation in Residential Garages



so that all burners and burner ignition devices are located not less



Such equipment shall be located, or protected, so it is not subject

to physical damage by a moving vehicle.

Qualied Installing Agency



or accessories and repair and servicing of equipment shall be





person or through a representative is engaged in and is responsible for

(a) the installation or replacement of gas piping or (b) the connection,

installation, repair or servicing of equipment, who is experienced in

such work, familiar with all precautions required and has complied

with all the requirements of the authority having jurisdiction.

      



of Massachusetts.

The installation must conform with local codes, or in the absence of

local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or

Natural Gas and Propane Installation Code, CSA B149.1.

*Available from the American National Standards Institute, Inc., 11



A manufactured home (USA only) or mobile home OEM installation

must conform with the Manufactured Home Construction and Safety

Standard, Title 24 CFR, Part 3280, or, when such a standard is not

applicable, the Standard for Manufactured Home Installations, ANSI

Z225.1, or Standard for Gas Equipped Recreational Vehicles and

Mobile Housing, CSA Z240.4.

High Altitudes

For altitudes/elevations above 2,000 feet (610m), input ratings should

be reduced at the rate of 4 percent for each 1,000 feet (305m) above

sea level, this may be accomplished by reducing manifold pressure.

The maximum allowable reduction in manifold pressure for Natural

Gas shall be from 3.5" w.c. (.872kPa) to 2.8" w.c. (.697kPa). The

maximum allowable reduction in manifold pressure for Propane

Gas shall be from 10.0" w.c. (2.49kPa) to 8.0" w.c. (1.99kPa). For

Canadian high altitude applications, this appliance is suitable for

installation at elevations between 0 feet (0m) and 4,500 feet (1,372m)

without change.

INTRODUCTION

19562-8-0919 Page 7

INTRODUCTION (CONT'D)

SPECIFICATIONS

Model DV-20E DV-40E

 20,000 (5.9) 40,000 (11.7)

Height 26" (660mm) 26" (660mm)

Width 37" (940mm) 37" (940mm)

Depth with Shroud

15 3/4"

(400mm)

15 3/4"

(400mm)

Gas Inlet (Pipe) 1/2" (13mm) 1/2" (13mm)

Electrical - Unit as a 5' (1.5m) 3 pronged cordset for

connection to an approved 115 VAC 60HZ

minimum AMPs - 5A wall receptacle.

Accessories

Extended Vent Terminal

For walls up to 32" (813mm)

DVT-2



 DVE-1



for Extended Vent Runs

DVE-2 (use

with DVE-1)

Floor Pad DVP-1

 DV-1108



See page 12 for requirements.

CONVERSION KITS

Part Number Description Used On

DV1124 Propane to Natural DV20E-5LPG

DV1123 Natural to Propane DV20E-5NAT

DV1097 Propane to Natural DV40E-5LPG

DV1096 Natural to Propane DV40E-5NAT

When an existing Category 1 heater is removed or replaced,

         

properly vent the attached appliances. Instructions shall



(formation of condensate, leakage, spillage, etc.) and shall



WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each

appliance connected to the venting system being

placed into operation could result in carbon monoxide

poisoning or death.

The following steps shall be followed for each

appliance connected to the venting system being

placed into operation, while all other appliances

connected to the venting system are not in operation:

1. Seal any unused openings in the venting system.

2. Inspect the venting system for proper size and

horizontal pitch, as required in the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 or the Natural

Gas and Propane Installation Code, CSA B149.1

and these instructions. Determine that there is no

blockage or restriction, leakage, corrosion and

other deciencies which could cause an unsafe

condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which

the appliance(s) connected to the venting system

are located and other spaces of the building.

4. Close replace dampers.

5. Turn on clothes dryers and any appliance not

connected to the venting system. Turn on any

exhaust fans, such as range hoods and bathroom

exhausts, so they are operating at maximum

speed. Do operate a summer exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the

thermostat so appliance is operating continuously.

7. Test for spillage from draft hood equipped

appliances at the draft hood relief opening after 5

minutes of main burner operation. Use the ame

of a match or candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected

in accordance with National Fuel Gas Code, ANSI

Z223.1/NFPA 54 and/or Natural Gas and Propane

Installation Code, CSA B149.1.

9. After is has been determined that each appliance

connected

to the venting system properly vents

when tested as outlined above, return doors,

windows, exhaust fans, replace dampers and

any other gas-red burning appliance to their

previous conditions of use.

19562-8-0919Page 8

Consult the current National Fuel Gas Code, ANSI Z223.1

CAN/CGA-B149 (.1 or .2) installation code.

Recommended Gas Pipe Diameter

Pipe

Length

Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Natural Propane Natural Propane

0-10 feet

0-3 meters

1/2”

12.7mm

3/8”

9.5mm

1/2”

12.7mm

3/8”

9.5mm

10-40 feet

4-12

meters

1/2”

12.7mm

1/2”

12.7mm

5/8”

15.9mm

1/2”

12.7mm

40-100

feet

13-30

meters

1/2”

12.7mm

1/2”

12.7mm

3/4”

19mm

1/2”

12.7mm

100-150

feet

31-46

meters

3/4”

19mm

1/2”

12.7mm

7/8”

22.2mm

3/4”

19mm

NOTE:



NOTE: Since some municipalities have additional local codes, it

is always best to consult your local authority and installation code.



— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANS Z21.45 Assembled Flexible Appliance Connectors of Other

Than All-Metal Construction

The above connectors may be used if acceptable by the authority

having jurisdiction. The Commonwealth of Massachusetts requires



Figure 1

Installing a New Main Gas Shut-Off

Each appliance should have its own manual gas shut-off.

A manual main gas shut-off should be located in the vicinity of the





Compounds used on threaded joints of gas piping shall be resistant



checked for leaks by the installer. This should be done with a soap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made.

Never use an exposed ame to check for leaks. Appliance must

be disconnected from piping at inlet of control valve and pipe

capped or plugged for pressure test. Never pressure test with

appliance connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required by

the National Fuel Gas Code that a drip line be installed near the gas

inlet. This should consist of a vertical length of pipe tee connected

into the gas line that is capped on the bottom in which condensation

and foreign particles may collect.

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.

plugged tapping, accessible for test gauge connection, must be

placed immediately upstream of the gas supply connection to

the appliance.

2. The appliance and its individual shut-off valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of

1/2 psig (3.5 kPa).

3. The appliance must be isolated from the gas supply piping system

by closing its individual manual shut-off valve during any pressure

testing of the gas supply piping system at test pressures equal

to or less than 1/2 psig (3.5 kPa).

Attention! If one of the procedures results in pressures in excess of





Checking Manifold Pressure

Both Propane and Natural Gas valves have a built-in pressure

regulator in the gas valve. Natural gas models will have a manifold

pressure of approximately 3.5" w.c. (.872kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 5.0" w.c.

(1.245kPa) for the purpose of input adjustment to a maximum of

10.5" w.c. (2.614kPa) Propane gas models will have a manifold

pressure approximately 10.0" w.c. (2.49kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 11.0" w.c.

(2.739kPa) for the purpose of input adjustment to a maximum of

13.0" w.c. (3.237kPa).

A 1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge

connection, is located on the outlet side of the gas control.

GAS SUPPLY

19562-8-0919 Page 9

Warning: Conversion must be done by a qualied service technician. Main burner orice(s)

and new gas conversion label are provided in conversion kit attached to manifold pipe.

1. Make sure gas supply to furnace is off prior to conversion and disconnect electrical power to unit.

2. Open brass union located between the gas valve and burner box. Remove

the 4 mounting screws securing manifold plate to the burner box. Remove

the top 2 screws holding the burner box top in place and then remove the

1 screw holding the end of the manifold pipe in place. Grasp union and

remove manifold pipe.

 







55 for DV-40E supplied in conversion kit.

  

burner. Secure the manifold and top burner box cover in place using the screws earlier removed. Reconnect the brass union.

5. Remove the vinyl cap and unscrew the gas control convertible regulator and reverse to Propane Gas side (red ring on regulator)



 

indicating that the unit was converted to Propane Gas.

7. Turn on gas supply to furnace and check all gas connections for leaks with soap solution, watching for bubbles on all gas connec-

tions.

8. Turn on electrical power to unit and turn on furnace to verify proper operation. It may take several tries for ignition to completely

purge all the air from the gas line.

Warning: Conversion must be done by a qualied service technician. Main burner orice(s)

and new gas conversion label are provided in conversion kit attached to manifold pipe.

1. Make sure gas supply to furnace is off prior to conversion and disconnect electrical power to unit.

2. Open brass union located between the gas valve and burner box. Re-

move the 4 mounting screws securing manifold plate to the burner box.

Remove the top 2 screws holding the burner box top in place and then

remove the 1 screw holding the end of the manifold pipe in place. Grasp

union and remove manifold pipe.

 







44 for DV-40E supplied in conversion kit.

burner. Secure the manifold and top burner box cover in place using the

screws earlier removed. Reconnect the brass union.

5. Remove the vinyl cap and unscrew the gas control convertible regulator and reverse to Natural Gas side and screw back into place.



 -

plate indicating that the unit was converted to Natural Gas.

7. Turn on gas supply to furnace and check all gas connections for leaks with soap solution, watching for bubbles on all gas connec-

tions.

8. Turn on electrical power to unit and turn on furnace to verify proper operation. It may take several tries for ignition to completely

purge all the air from the gas line.

TOPVIEW

BACKEND VIEW

GASCONTROLLEVERSHOWN

IN "OFF"POSITION

OFF

CONVERTIBLE

REGULATOR

VINYLCAP

RED LP RING

CONVERSION INSTRUCTIONS FROM NATURAL GAS TO PROPANE GAS

TOPVIEW

BACKEND VIEW

GASCONTROLLEVERSHOWN

IN "OFF"POSITION

OFF

CONVERTIBLE

REGULATOR

VINYLCAP

RED LP RING

GAS CONVERSION INSTRUCTIONS

CONVERSION INSTRUCTIONS FROM PROPANE GAS TO NATURAL GAS

19562-8-0919Page 10

1. Pick a location on a wall with a clear space of 36" (91.4cm)

high by 43" (109cm) wide in the room. In selecting a location

for installation, it is necessary to provide adequate accessibility

clearances for servicing and proper installation. Be sure to locate

the unit close enough to a 115 VAC wall receptacle to properly

power appliance.

2. Unit is supported by a wall bracket secured to the wall.

3. When facing the front of the furnace the minimum clearances

from casing to combustible construction are 10" (254mm) on

top, 3" (76mm) on each side, recommend 18" (457mm) on right



rear wall.

 



5. The minimum distance from the center of the vent cap to the

nearest outside corner or obstruction is 12" (305mm).

6. The minimum wall depth is 2" (51mm) and the maximum is

10" (254mm) [or 32"(813mm) using the extended vent terminal

kit accessory]. The use of vent tubes not supplied by the

manufacturer may result in unsatisfactory performance.

The vent terminal of a direct vent appliance, with an input of 50,000





The bottom of the exhaust vent terminal and the air intake shall be

located at least 12" (305mm) above grade and must be vented outside.

WARNING

The nearest point of the vent cap should be a minimum horizontal

distant of six (6) feet (1.83m) from any pressure regulator. In

case of regulator malfunction, the six (6) feet (1.83m) distance

will reduce the chance of gas entering the vent cap.

Installation on Rugs and Tile

If this appliance is to be installed directly on carpeting, tile, or other



be installed on a metal or wood panel extending the full width and

depth of the appliance.



used on wood stoves. The protection is primarily for rugs that may

be extremely thick and light-color tile that can discolor.

Locating Wall Opening (See Figures 2, 3 and 4)

The recommended location for this furnace is on an outside wall.

(The unit can be located on an inside wall but must be vented

using the extended vent kit and should not exceed 15' (4.6m) in

exhaust vent length.) Locate wall studs so that wall vent opening

will be located between wall studs. The wall studs can be used for

attachment of wall mounting bracket. The wall opening required for

venting is a 3 1/4" (83mm) minimum diameter opening.

Refer to Figure 2 for positioning the furnace on wall and for locating



and should be secured to the wall through the wall bracket secured

to the rear top shroud.

(76mm)

8 3/4"

(222mm)

12 5/16"

20" (508mm)

(313 mm)

(267mm)

10 1/2"

1/2" (13mm) DIA.

GAS SUPPLY

WALL

MAYBE20" TO 13"

TO AVOID STUD

31/4"(83mm) DIA. VENT

HOLE THRU OUTSIDE WALL

17 11/16"

(449mm)

FLOOR TO

BOTTOM OF

WALL BRACKET

FRONT OF FURNACE

Figure 2

Figure 3

2" (51mm) TO 13" (330mm)

2" (51mm) TO 32" (813mm)

Figure 4

CLEARANCES

FURNACE INSTALLATION

19562-8-0919 Page 11

Installing Wall Bracket (See Figures 5 and 6)

  

wall bracket must be positioned and installed. The bracket should

be mounted to the wall studs, if possible, or anchored solidly to the

wall. Use the (2) 10 x 1" (25mm) hex-head screws or (2) plastic

anchors

provided. Drill (2) 5/16" (8mm) diameter holes in wall if

plastic anchors are used. Attach the two wall mounting brackets to

the casing back by using (4) 10 x 1/2" (13mm) hex-head screws

provided.

Figure 5

ALL

CASING

BACK

#10X1"

WALL MOUNTING BRACKET

WALL

BRACKET

#10X1/2"

4" (102mm)

Figure 6

WALL

INTAKE FLEX HOSE

WITH CLAMPS

EXHAUST

INTAKE AIR

MOUNTING PLAT

EXHAUST ELBOW MAY

BE CUT TO LENGTH

TO FIT VENT BOX.

SECURE IN PLACE

USING HOSE CLAMPS

PROVIDED.

KEEP CAP ON

UN-USED AIR

INTAKE OPENING

Figure 7

EXHAUST AIR

ORANGE

SILICONE

ELBOW

CONNECTOR

INTAKE AIR

BLACK FLEXIBLE HOSE

Figure 8

VENT TUBING

SILICONE COUPLING

HOSE CLAMP

EDGE

EXHAUST CONNECTIONS

INTAKE FLEX HOSE CONNECTION

WITH INTERNAL METAL COUPLING

VENT COUPLING CONNECTIONS

EXTENDED VENT

Figure 9

Venting (Figures 7, 8 and 9)

This unit is vented directly out the back using the concentric vent

tube assembly provided. See Figure 2 for vent hole location. This

hole location can be conveniently moved closer to unit exhaust outlet

tube to avoid wall stud interference if necessary. The orange silicone

exhaust elbow would need to be cut to length. Do not locate vent

directly behind the exhaust outlet. Do not use the orange silicone





away from the heater. See Figure 12 for extended vertical venting.

The vent provided will accommodate walls up to 10" thick and can be

cut shorter for thinner walls if desired by using a hacksaw or cut-off

saw. Be sure to leave the minimum 3/4" of tube length extending

beyond the outside wall plate. Both the inner and outer tube will be

cut to the same length as the inner exhaust tube has an extension



FURNACE INSTALLATION (CONT'D)

19562-8-0919Page 12



easy after cutting the wall opening secure the vent terminal box

in place using the (4) 10 x 1" hex-head screws provided. Locate

the box so that the middle exhaust tube is directed toward the

furnace exhaust outlet opening. See Figure 8. Attach the black 2"



using a hose clamp. Secure the other end to the lower inlet air box

connector using the hose clamp. Do not kink hose. Attach the long

straight end of the 2" orange silicone exhaust elbow to the middle

vent terminal tube and rotate the elbow toward the furnace exhaust

outlet. Secure the hose to the vent box using a hose clamp. Carefully

push the furnace back closer to the wall and secure the exhaust

elbow to the 2" exhaust tube exiting the unit. Secure the elbow in

place using the last remaining hose clamp. The furnace can now

be secured to the wall.

The furnace can be vented with up to a maximum length of 15'

(4.6m) including termination vent and using 2 - 90° elbows. Also,

the furnace can be vented with up to a maximum length of 10' (3m)

including termination vent and using 3 - 90° elbows. For longer vent

lengths order the vent kit, Part Number DVE-1 and DVE-2. See

Figures 11 and 12 illustrating extended vent run and venting options.

NOTE: If the extended vent kit is used and the exhaust vent pipe

is run through a cold space, such as an attic or a garage, the pipe



          

condensation. Also, slope 1/4" (6mm) per foot (305mm) the vent



         

vent pipe runs of 5 feet (1.5m) or more in length may accumulate

condensation in the exhaust pipe and must, therefore, be sloped

downward to drain any condensate out of the end vent terminal.

Use straps or other suitable supports spaced every 5 feet (1.5m)

to adequately hold pipe. Be sure to avoid any low spots or sags in

pipe run. Be sure all connections are tight using the hose clamps

as shown in Figure 9, "Vent Coupling Connections."

For wall depths thicker than 10" (254mm) order the extended vent

terminal kit which will cover walls to 32" (813mm) thickness. The vent

pipes must be cut to length to assemble for desired wall thickness.

For extended venting, it is also acceptable to use 2" (51mm) diameter

PVC or ABS pipe for the combustion air intake supply piping only to



and ASTM Standards D1785 for SCH. 40 PVC, D2665 for PVC-

DWV, D2241 for SDR-21 and SDR-26 PVC, D2661 for ABS-DWV

and F628 for SCH. 40 ABS. Pipe cement and primer must be used

and conform to ASTM Standard D2564 for PVC or D2235 for ABS.

This PVC or ABS pipe must not be used for the exhaust vent

pipe run.

NOTE: Type SDR pipe is not approved for use in Canada.

For new construction installation, the intake and exhaust vent can be



wall. This can be done but not the preferred method of installation

due to the inability to perform periodic inspection of the vent system.

In doing this, it is important to securely seal the vent system and



toward the vent terminal outside to drain out any condensate. It is

also necessary to adequately support both the exhaust and intake

and to center the exhaust pipe in the wall.

Be sure to consult local codes prior to installation to verify allowable

procedures.

Installation of Shroud

To complete inside installation, secure furnace to the wall bracket

by attaching the two wall mounting brackets to the wall bracket by

using (2) 10 x 1/2" (13mm) hex-head screws provided. See Figures

4 and 6. To attach the right shroud and left shroud to the casing



the casing side. When positioned correctly, the (6) louvers on the

shroud will be facing up and the knock-out on the shroud will be

facing down. Attach the right shroud and left shroud to the casing

back with (3) 10x1/2" hex-head screws supplied in hardware package,

for each shroud. Attach top shroud to right shroud and left shroud

with (4) Phillips-head screws, supplied in hardware package. Insert





 

be able to be installed onto the side shrouds. The top shroud will

appear to be 2 inches, too narrow.

Vent Terminal (Figure 10)

Place the 6 3/8" x 6 3/8" (162mm x 162mm) black foam, wall plate

gasket within the mounting plate. The 4 3/4" (121mm) diameter hole

in the black foam gasket will allow for installation of the concentric

vent tube assembly. Slide the outside mounting plate into place on

the concentric vent tube assembly. The outside mounting plate should

seal against the face of the building and be secured in place using

(4) 10 x 1" hex-head screws. Be sure to caulk and seal around the

pipe on the exterior using high temperature exterior grade, silicone

caulk rated at 204°C/400°F. Wipe some silicone sealant on the 2"

(51mm) exhaust pipe extension. The end cap can be pushed into

place on the exhaust outlet tube.

Attention: The opening on the bottom of the end cap must be

positioned toward the ground. The opening on the bottom cannot

be pivoted to the right or left, it must be centered toward the ground.

Figure 10

FURNACE INSTALLATION (CONT'D)

NO. 10X11/2"

SCREWS (4)

INLETAIR

EXHAUST

AIR

12"(305mm)MIN.

ABOVE GRADE

CAULK AROUND PIPE

EXHAUST FITTING-SLIDE ONTO

2" EXHAUST TUBE AND USE RTV

SEALANT TO SECURE IN PLACE

WITH OUTLET POINTED DOWN

AS SHOWN

19562-8-0919 Page 13

INTAKE

SLOPE THE VENT TERMINAL

HORIZONTAL RUN DOWNWARD

THE OUTSIDE TO DRAIN OUT

ANY CONDENSATE

EXHAUST

VENT TERMINAL

EXHAUST AIR

ELBOW WITH

CLAMPS

INTAKE AIR

SUPPORTSTAP EVERY

5FT. (1.5m) MIN.

SHROUD SIDE

EXHAUST

AIR

INTAKE AIR

EXTERIOR WALL

COUPLING WITH

HOSE CLAMPS

SLOPE DOWNWARD 1/4" (6mm)

PER FOOT (m)TO DRAIN ANY

CONDENSATE OUTSIDE

FILTER

TEMPERATURE CONTROL DOOR

INTERIOR WALL

Figure 11

Condensate Removal (Figures 11 and 12)

The condensate drain kit is used in conjunction with DVE and

DVE-2, intake/exhaust extension kits. The condensate drain kit is

required whenever there is a vertical vent run, in a heated room

[10 ft. (3m) or more for DV-40E or 6 ft. (1.8m) or more for DV-20E],

in the intake/exhaust venting.

Whenever a vertical vent run, in a heated room [10 ft. (3m) or more



run are combined, you must purchase the optional condensate drain

kit, part number DV-1108. If the vertical vent run lengths are less

than those required for the condensate drain kit, you can slope the



outside. However, if local codes prohibit condensate from draining

       

portion of the vent run must slope downward, to the appliance, 1/4"



condensate drain kit. Do not use the orange silicone elbow supplied



the condensate drain kit to an existing drain or into the condensate

drain pan located within the appliance.



can slope the exhaust pipe downward, to the outside, 1/4" (6mm)

per foot (305mm). The downward slope on the exhaust pipe will



If local codes prohibit condensate from draining to the outside and

the appliance produces condensate you must purchase condensate

drain kit, part number DV-1108.

Figure 12

Reassembly and Resealing Vent-Air Intake System

When vent-air intake system is removed for servicing the furnace,

the following steps will assure proper reassembly and resealing

of the vent-air intake assembly. Be sure all hose connections and

elbow assemblies are re-secured in place using the hose clamps





rated at 204°C/400°F to reseal the inlet air vent pipe and exhaust

air vent pipe to the mounting plate.

FURNACE INSTALLATION (CONT'D)

19562-8-0919Page 14

FOR YOUR SAFETY READ BEFORE OPERATING

A. This appliance does not have a pilot. It is equipped

with an ignition device which automatically lights

the burner.

Do not try to light the burner by hand.

B. BEFORE OPERATING smell all around the appli-

ance area for gas. Be sure to smell next to the

oor because some gas is heavier than air and

will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call

the re department.

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will

not push in or turn by hand, don't try to repair

it; call a qualied service technician. Force or

attempted repair may result in a re or explo-

sion.

D. Do not use this appliance if any part has been

under water. Immediately call a qualied ser-

vice technician to inspect the appliance and to

replace any part of the control system and any

gas control which has been under water.

1. STOP! Read the safety information above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. This appliance is equipped with an ignition

device which automatically lights the burner. Do not

try to light the burner by hand.

5. Remove control access panel (front panel).

6. Turn gas control knob clockwise

to "OFF."

7. Wait ten (10) minutes to clear out any gas.



smell gas, STOP! Follow "B" in the safety information

above. If you don't smell gas, go to the next step.

8. Turn gas control knob counterclockwise

to "ON".

9. Replace control access panel (front pan-

el).

10. Turn on all electric power to the appliance.

11. Set thermostat to desired setting.

12. If the appliance will not operate, follow the instructions

"TO TURN OFF GAS TO APPLIANCE" and call your

service technician or gas supplier.

OPERATING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to lowest setting.

2. Turn off all electric power to the appli-

ance if service is to be performed .

3. Remove control access panel (front

panel).

4. Turn gas control knob clockwise

to "OFF." Do not force.

5. Replace control access panel (front

panel).

TOPVIEW

BACKEND VIEW

GASCONTROLLEVERSHOWN

IN "OFF"POSITION

OFF

CONVERTIBLE

REGULATOR

VINYLCAP

LIGHTING INSTRUCTIONS

WARNING

If you do not follow these instructions exactly, a re or explosion may result causing property damage,

personal injury or loss of life.

19562-8-0919 Page 15

The appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical



This

appliance is equipped with a three-prong [grounding] plug for your



a properly grounded three-prong receptacle. Do not cut or remove

the grounding prong from this plug. For an ungrounded receptacle,

an adapter, which has two prongs and a wire for grounding, can

be purchased, plugged into the ungrounded receptacle and its

wire connected to the receptacle mounting screw. With this wire

completing the ground, the appliance cord plug can be plugged

into the adapter and be electrically grounded.

CAUTION

Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous

operation. Verify proper operation after servicing.

NOTE:

series with sensor. Minimum current should be 1 micro-amp dur



If current is below 1 micro-amp, remove sensor, clean with light

sandpaper and retest.

NOTE: This heater is equipped with a remote bulb electronic

thermistor control located down low at the back of the furnace.



control sensing of the thermistor. This sensing bulb can be re-located

if necessary to provided for better room air sensing and control.

Replacement of Thermistor with 24 Volt Wall Thermostat

1. If furnace is installed, turn off gas supply and electric supply.

2. Remove casing front.

3. Remove black hose from front nipple on pressure switch.

4. Remove junction box cover (4 screws).

5. Please refer to wiring diagram for removal of the following

wires.

6. Internal Electronic Thermostat/Temperature Control Board

Attention! No 24 volt wall thermostat wires are to be attached

to the internal electronic thermostat.

7. Control Board

A. Remove white wire form screw marked W.

B. Remove yellow wire from screw marked C.

C. Remove red wire from screw marked R.

8. Route (2) wires from any 24 volt wall thermostat through the

casing back of furnace to the screws marked W and R on

the control board.

9. Replace junction box cover (4 screws).

10. Replace black hose onto front nipple on pressure switch.

11. Replacement of thermistor with 24 volt wall thermostat is

completed.

CIRCULATING AIR BLOWER

WHT

RED

YEL

RED

BLK

PUR

INDUCER

BLOWER

BLU

IF ANYOFTHE ORIGINAL WIRE AS SUPPLIED WITH THE

APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED

WITHAWIRE OF AT LEAST 105

C TEMPERATURE RATING.

LIMIT SWITCH

SECONDARY

FIELD INSTALLED

THERMOSTAT

24 VOLT

115VAC

SWITCH

LIMIT

3A FUSE

GND

BLACK

WHITE

ON/OFF

ROLLOUT

PRESSURE

SWITCH

R-8191

VALVE

GAS

TRANSFORMER

24 VA C

PRIMARY115 VA C

COMMON

DISCONNECT INTEGRAL THERMOSTAT "R", "W", AND "C" LEADS AND ATTACH WALL THERMOSTAT AS SHOWN

PSROS

RED

GRN

ORG

ELECTRONIC

THERMOSTAT

INTEGRAL

WHT

YEL

RED

GRY

BRN

GRY

24 V

WHT

BLK

115 V

OPTIONAL WALL MOUNT THERMOSTAT

XFMR

ON/OFF

BLACK NEUTRAL

RIBBED

INSULATION

BLACK HOT

SMOOTH

INSULATION

CIRCULATING AIR

BLOWER MOTOR

RED LED

STATUS

LIGHT

IGN

HOT SURFACE

IGNITOR

POWER SWITCH

INDUCER MOTOR

FLAME SENSOR

COMBUSTION AIR

ROS = ROLLOUT LIMIT SWITCH

IGN = HOT SURFACE IGNITOR

PS=PRESSURE SWITCH

XFMR=TRANSFORMER

CORDSET 11 5VAC

FS=FLAME SENSOR

GV=GAS VA LVE

LS=LIMIT SWITCH

4 1

WIRING

19562-8-0919Page 16

blower comes on for 15 seconds pre-purging out any gas

and closing the pressure switch.

 



gas valve and igniting the burners. After burning for about

30 seconds, the circulating air blower comes on, delivering

warm air to the room. If ignition does not occur, the ignition

sequence is repeated again up to 2 more times. (3 trials

for ignition-total)

 

gas valve closes and the circulating air blower continues

to run for about 2 minutes and then shuts off. The inducer

blower runs for 5 seconds and shuts off.

If for any reason ignition and operation does not occur, the

control board will blink the red fault status LED, a sequence

code, indicating what to look for as a troubleshooting guide.

If the red LED is ON but not blinking check the electronic

temperature control to verify its operation. This can be

easily done by disconnecting the 3 electronic temperature

control leads from the main furnace board and using a

pig tail jumper to connect R & W together on the board. If

the furnace comes on and runs normally the temperature

control board is malfunctioning. If the heater still does not

come on, then the main furnace board is malfunctioning.

Look for any fault codes below and verify the 3 amp fuse

is not blown.



performance, however, a yearly inspection of the burners ,



done. Be sure all passageways are open and clear of any

obstruction, or soot build up. Be sure to shut off all power to

the unit while performing this inspection.



water to remove all dirt. Shake dry and reinstall in unit.

System Operation

1. This furnace has an electronic thermostat and control

board to monitor the room temperature and then control

the furnace operation to provide the best comfort and

performance from a heating appliance. To operate unit

turn ON/OFF switch to ON and then turn temperature

control knob clockwise slowly till furnace turns on. For

typical room comfort, the control knob should be pointed

toward medium.

2. The furnace control board follows sequence of operation

which allows for self diagnosis in the event there is a

problem. The control then blinks a status light, a set number

of blinks based on what problem has been encountered.

When the furnace is on and there is a no fault condition,

the red LED is on.

On a typical call for heat by the integral thermostat 24

VAC is applied to the W terminal on the board.

 

Proper Main Burner Flame





Figure 13

Cleaning Main Burner(s)

Remove main burner(s) and apply air pressure inside the

throat and ports of the main burner(s).

Removing Main Burner(s)

1. Remove front grill assembly.

2. Remove burner compartment access panel (2 screws).

3. Remove main burner(s) from burner compartment (2

screws per main burner).

Removing Gas Valve

1. Remove front grill assembly.

2. Disconnect manifold union assembly at gas valve.

3. Remove (2) two 24 volt wires from gas valve. Label wires

prior to disconnection from gas valve.

4. Remove gas valve from gas valve bracket.

Removing Main Burner Orice(s)

1. Remove front grill assembly.

2. Remove burner compartment access panel (2 screws).

3. Disconnect manifold union assembly.

4. Disconnect manifold union assembly brackets (5 screws).

Removing Ignitor and Flame Sensor

1. Remove front grill assembly.

2. Remove ignitor from burner compartment (2 screws).

 

Cleaning Combustion (Exchanger) Assembly

A QUALIFIED SERVICE PERSON should remove the

combustion (exchanger) assembly. Apply air pressure to the

inside of the combustion (exchanger) assembly in order to

clear all passageways.

Oiling

The blower motor has an oil hole located on each end of the

motor. Use #20 motor oil only. It is best to oil the motor several

times during the heating season using 2 or 3 drops each time.

MAINTENANCE

OPERATION AND TROUBLESHOOTING

19562-8-0919 Page 17

FAULT SEQUENCE CODE — TROUBLE SHOOTING GUIDE

# of Blinks Fault Condition

Fault Correction

Steady On Control OK

1 Flash Temperature limit switch is open

-Check Circulating Air Blower Inlet or Grill Outlet for

Blockage, Inducer Blower/Circulating Air Blower Run

to Cool Heat Exchanger and Limit

-Check for Flame Roll Out Condition Causing Roll Out

Limit Switch on Burner Box to Open

-Clean Circulating Air Filter

2 Flashes Pressure switch is open with inducer on

-Check Heat Exchanger and Flue System, Outlet and

Inlet for Restriction



-Check Pressure Switch

3 Flashes Pressure switch is closed with inducer off -Check Pressure Switch and Replace

4 Flashes Lockout due to failed ignition

-Check for Broken Ignitor

-Check for Bent Ignitor Bracket - Ignitor too far from

Burner

-Check for Flame Sensor Malfunction/or False Ground

-Check Gas Valve

-Reset Thermostat

 L1/Neutral reversed or voltage not present on L1

-Shut Off Power to Unit and Dis-Connect Cordset Plug

from Wall Receptacle.

Open Junction Box and Un-Reverse Polarity of Incom-

ing Power Leads

Rapid

Flash

Flame sense or internal control fault

-Check Ignitor Operation

-Check Flame Sensor for Malfunction or False Ground-

ing

-Check Gas Valve

-Reset Thermostat

NOTE: If the hot surface ignitor is to be replaced, be sure to disconnect all power to the unit. Be very careful in handling the

new ignitor as they are fragile and can be broken easily if hit or dropped.

Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order

parts through the distributor. Parts can be shipped directly to the service person/dealer.



plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from

the following appropriate illustration and list. Be sure to give all this information.

Furnace Model Number _____________________________ Part Description _________________________________

Furnace Serial Number _____________________________ Part Number ____________________________________

Type of Gas (Propane or Natural) ____________________________________________________________________

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware

store.



Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, IL 62222-0529

HOW TO ORDER REPAIR PARTS

FURNACE CONTROL BOARD DIAGNOSTICS

19562-8-0919Page 18

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

PARTS LIST

INDEX

NO.

PART

NO.

DESCRIPTION

1 DV-1378 SHROUD TOP

2 DV-1376 SHROUD SIDE RIGHT

3 R-2521 AIR FILTER

4 DV-1375 FILTER RETAINER

5 DV-1379 

6 DV-1048 

7 R-2586 CONTROL DOOR PIN - 2 REQUIRED

8 19676 

9 DV-1373 CASING TOP

10 DV-1368 BLOWER HOUSING - 2 REQUIRED

11 R-2584 BLOWER WHEEL - 2 REQUIRED

12 R-2573 BLOWER MOTOR

13 R-2598 MOTOR BASE WASHER - 4 REQUIRED

14 R-1279 LIMIT SWITCH

15 DV-1367 INNER TOP

16 R-2546 

17 R-2522 ON/OFF SWITCH

18 19561 JUNCTION BOX

19 DV-1370 JUNCTION BOX COVER

20 R-1995 TRANSFORMER

21 R-6989 PRESSURE SWITCH

22 R-8140 CONTROL BOARD

23 R-2577A TEMPERATURE CONTROL BOARD

24 DV-1365 

25 R-1468 STRAIN RELIEF BUSHING

26 R-2099 CORD SET

27 DV-1371 INNER END

28 DV-1372 CASING SIDE - 2 REQUIRED

29 15790 

29 15791 

30 R-2519 INDUCER WHEEL

31 DV-1169 INDUCER BLOWER HOUSING

32 R-2523 INDUCER MOTOR

33 15783 

33 15784 

34 27523 

37 R-2543 FLAME SENSOR

38 R-12593 BURNER (2 REQUIRED ON DV-40E-5)

39 R-2575 FLAME ROLLOUT SWITCH

40 DV-1038 BURNER COMPARTMENT ACCESS PANEL

41 DV-1039 BURNER COMPARTMENT

42 R-3237 GAS VALVE (NATURAL GAS)

42 R-3238 GAS VALVE (PROPANE GAS)

43 DV-1366 

44 DV-1016 

44 DV-1013 

45 P-88-44

ORIFICE (NATURAL GAS) - 1 REQUIRED ON

DV-20E-5

45 P-88-55

ORIFICE (PROPANE GAS) - 1 REQUIRED

ON DV-20E-5

45 P-88-44

ORIFICE (NATURAL GAS) - 2 REQUIRED ON

DV-40E-5

45 P-88-55

ORIFICE (PROPANE GAS) - 2 REQUIRED

ON DV-40E-5

46 M-148 

47 DV-781 

48 M-155 

49 DV-1040 

50 DV-1024 BOTTOM SHIELD

51 DV-1363 

52 DV-1380 

53 R-2539 HOSE CLAMP - 4 REQUIRED

54 R-3113 INLET HOSE

55 R-3111 OUTLET ELBOW

56 DV-1192 

57 R-3114 INLET CAP

58 R-3115 

59 R-2587 

60 DV-1195 WALL PLATE - OUTSIDE

61 DV-1193 TUBE SPACER

62 DV-1194 

63 DV-1377 SHROUD SIDE LEFT

NS DV-1361 BAFFLE - 1 REQUIRED ON DV-20E-5

NS DV-1108 

NS DV-1132 

NS R-8142 

NS R-2563 

NS - NOT SHOWN

INDEX

NO.

PART

NO.

DESCRIPTION

19562-8-0919 Page 19

PARTS VIEW

19562-8-0919Page 20

APPLIANCE SERVICE HISTORY

Date Dealer Name Service Technician Name Service Performed/Notes

La page est en cours de chargement...

Empire Heating Systems High-Efficiency Wall Furnace (DV20E, DV40E) Le manuel du propriétaire

Marque: Empire Heating Systems

Modèle: High-Efficiency Wall Furnace (DV20E, DV40E)

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Empire Heating Systems High-Efficiency Wall Furnace (DV20E, DV40E) Owner's manual

Empire Heating Systems High-Efficiency Wall Furnace (DV20E, DV40E) Le manuel du propriétaire

Ce manuel convient également à

Empire Heating Systems High-Efficiency Wall Furnace (DV20E, DV40E) Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents