Modern Forms FR-W1806 Cervantes Mode d'emploi

Cervantes

Installation Instructions

works with the

Google Assistant

FR-W1806

Cervantes Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FR-W1806Cervantes Instructions 3

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email: customerservice@modernforms.com

Or live chat at modernforms.com

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 2

MON-FRI 8AM-8PM EST

Email: fansupport@modernforms.com

General Inquiries

Fan Support

FR-W1806

Cervantes Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned o at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the oor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or nish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FR-W1806 Cervantes Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms. Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app

or Wi-Fi Touch Panel Wall Control (not included).

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of re, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power o at the circuit breaker.

FR-W1806

Cervantes Instructions6

Get Smart...

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Premium smart

features:

Accessories:

DC

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

more ecient than AC fans

Wi-Fi and Bluetooth enabled

for exible control

Bluetooth Wall Control

Dims light to 1% | ON/OFF

6 fan speeds | Sold separately

F-WCBT-WT White

Bluetooth Remote Control

Dims light to 1% | ON/OFF

6 fan speeds

F-RCBT-WT White

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FR-W1806 Cervantes Instructions 7

1. Mounting Options 10

2. Hanging the Fan 12

2. Hanging the Fan 14

3. Attaching the Fan Blades 14

4. Making the Electrical Connections 16

5. Installing the Optional Wall Control 18

6. Finishing the Installation 20

7. Installing the Adapter Plate 20

8. Installing the LED Luminaire Module 22

9. Controlling the Fan 24

10. Reset 26

11. Breeze Mode 26

12. Application 26

13. Accessories 28

14. Troubleshooting 30-32

Contents

Tools Required

F R -W180 6

Cervantes Instructions8

*** denotes blade sweep of fan

Package Contents

7. Adapter Plate

8. LED Module

F4IN-120V-R1-30

9. Glass Shade w/Trim

RPL-F1806-GLA**

10. Luminaire Cover

RPL-F1806-COVER-**

11. Control Receiver

w/ Hardware

F-R3-1806-056

12. Remote w/Wall Cradle

F-RCBT-WT

• Wood screw (1), screws (2)

• 5/32” lock washers (2),

Ø10xØ4mm flat washers (2)

Hardware Bag

RPL-CERVANTESPART

1. Blade Set of 4

RPL-F1806-54-BD-**

2. Blade Arm Set of 4

RPL-F1806-ARM-**

3. Hanger Assembly

Mounting Bracket

Downrod Assembly

RPL-HGR-ASM-**

4. Canopy & Canopy

Screw Cover

RPL-CAN-CYL-**

5. Coupling Cover

6. Motor Assembly

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

• 5.4mm lock washer (1),

Ø14xØ6mm flat washer (1)

wire nuts (8)

• Screws with rubber washers (13)

FR-W1806 Cervantes Instructions 9

1

4

2

7

9

8

10

11

5

6

3

IMPORTANT: Please make note

of the MAC ID on the

receiver and keep it in a

safe place.

Hanging Weight: 20 lbs

MAC ID

12

FR-W1806

Cervantes Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned o at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The

outlet box and support structure must be able to fully support the

moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic

outlet boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure.

Figures 1-1C are examples of dierent ways to mount the

outlet box.

NOTE: To hang your fan where there is an existing xture but no

ceiling joist, you may need an installation hanger bar.

NOTE: Downrod fans can be suspended up to a maximum

recommended length of 72” using additional downrods

(sold separately) and the included 80” lead wire.

NOTE: The sloped ceiling kit (sold separately) is required for sloped

ceiling applications, and will accommodate slopes up to 45° (Fig. 1B).

NOTE: You may need a longer downrod to maintain proper blade

clearance when installing on a steep, sloped ceiling (Fig. 1B).

FR-W1806 Cervantes Instructions 11

1

1A

1B

1C

1

2

1

2

3

1. Support Brace

2. Outlet Box

3. Joist

1. Support Brace

2. Mounting Bracket

3. Recess Outlet Box

1. Outlet Box

Support Ceiling

Max 30° Angle

FR-W1806

Cervantes Instructions12

2. Hanging the Fan

1. Disconnect power at the breaker to the fan location.

A licensed electrician must install the fan.

2. Remove 1 of 2 screws from the bottom of mounting bracket and

save for use in Finishing the Installation section. Loosen the other

screw (Fig. 2).

3. Pass the 120-volt supply wires through the center hole in the

ceiling mounting bracket as shown in (Fig. 2A).

4. Secure the mounting bracket to the ceiling outlet box with the

screws and washers provided with your outlet box.

5. Take out the screw located in the hanger ball, lower the hanger

ball and remove the cross pin. Remove the hanger ball from the

hanger ball/downrod assembly (Fig. 2B).

6. Remove the clevis pin and cotter pin, and loosen the two collar

screws from the motor collar (Fig. 2B).

7. Carefully feed the motor wires and safety cable up through the

downrod. Thread the downrod into the collar.

8. Align the holes of downrod and collar and insert the cotter pin

and clevis pin. Tighten the two collar screws (Fig. 2B).

9. Slip the coupling cover, canopy screw cover (painted side

face down), and canopy (opened side up) onto the downrod

(Fig. 10). Coupling cover goes all the way to the bottom.

10. Carefully reinstall the hanger ball onto the downrod, being sure

that the cross pin is in the correct position, the setscrew is

tightened and wires are not twisted (Fig. 2B).

WARNING: Failure to properly install the cotter pin and/or

tighten the screws could result in the fan loosening and

possibly falling.

FR-W1806 Cervantes Instructions 13

2

1

2B

2A

1. Mounting Bracket

2. Screw

2

1. Cross Pin

2. Hanger Ball

3. Screw

4. Downrod

5. Safety Cable

6. Motor Wires

7. Downrod

8. Screws

9. Collar

10. Cotter Pin

11. Clevis Pin

4

1

5

8

1011

6

7

9

3

2

1. 120V Wires

2. cUL Listed Electrical Box

3. Mounting Bracket

4. Mounting Screws

(supplied with outlet box)

1

2

3

4

FR-W1806

Cervantes Instructions14

11. Carefully lift the fan motor assembly up to the mounting bracket

and seat the hanger ball in the mounting bracket socket. Make

sure the tab on the mounting bracket socket is properly seated in

the groove in the hanger ball (Fig. 2C). Rotate the socket assembly

until the ball drops and locks into the hanger bracket screw.

12. Secure the safety cable into the structure beams using the wood

screw, washers, and spring washers provided (Fig. 2D).

NOTE: A Safety cable is required for all installations in Canada. Safety

cable is required for ceiling fan and light combinations over

35 lbs. in both ush and downrod models in the United States.

2. Hanging the Fan

1. Attach the blade to the blade arm using the screws with lock

washers as shown in (Fig.3).

2. Fasten blade assembly to motor using the screws supplied (Fig.3).

3. Attaching the Fan Blades

FR-W1806 Cervantes Instructions 15

2C

2D

1. Wood Screw

2. Safety Cable

1. Motor Wires

2. Safety Cable

3. Downrod

4. Canopy

5. Canopy Screw Cover

6. Coupling Cover

1

2

4

1

3

5

6

2

3

1. Screw

2. Screws with

Lock Washer

3. Blade Arm

4. Blade

4

2

3

1

FR-W1806

Cervantes Instructions16

4. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground wire) which should run between ceiling and

wall outlet box.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire.

Insert the receiver into the mounting bracket with the at side of the

receiver facing the ceiling (Fig. 4).

Motor to Receiver & Receiver to house supply wires (Fig. 4A).

1. Connect the hanger ball/downrod assembly ground wire,

mounting bracket ground wire and receiver ground wire to

the ground wire in outlet box.

WARNING: Failure to connect ground wires could result in

poor fan control functionality.

2. Connect the red wire from the fan to the red wire marked

“TO MOTOR” from the receiver.

3. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

4. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

5. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

6. Connect the blue wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

7. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

8. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

FR-W1806 Cervantes Instructions 17

Follow the steps above to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

4

4A

1. Mounting Bracket

2. Receiver

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLUE (for Light)

GREEN(GND Must Use)

GREEN(Hanger Bracket Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

WHITE(Neutral)

Safety Cable

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver

Hanger Ball & Downrod

Hanger

Bracket

1

2

FR-W1806

Cervantes Instructions18

5. Installing the Optional Wall Control

1. Connect the green wire marked “GROUND” from the wall

control to the copper wire from the wall outlet box that

feeds back to the circuit breaker – important for proper

fan function (Fig. 5).

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall

outlet box that feeds back to the circuit breaker (Fig. 5).

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan (Fig. 5).

4. Connect the white wire from the wall control to the white

(neutral) wire from the wall outlet box (Fig. 5).

5. Carefully tuck the wire connections inside the outlet box.

Secure the wall control with the two (2) wall control screws

provided (Fig. 5A).

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided (Fig. 5A).

7. Fasten the wall plate to the wall mounting plate (Fig. 5A).

5

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

From Breaker

* Home Wiring may vary

to Fan

FR-W1806 Cervantes Instructions 19

5A

Multi-location wiring

1 2 3

54

1. Wall Outlet

2. Wall Control

3. Wall Mounting Plate

4. Mounting Plate Screws

5. Wallplate

Individually pair each of the wall controls with the fan

receiver using the pairing instruction. See page 25.

Line/Hot

Red

Green (Green or Bare)

Wallcontroller 1 Wallcontroller 2 Wallcontroller 3

If Applicable

FAN

Neutral/White

Wall Control 1 Wall Control 2 Wall Control 3

FR-W1806

Cervantes Instructions20

6. Finishing the Installation

1. Secure all wire connections with supplied wire ties to assist in

canopy installation.

2. Tuck connections neatly into ceiling outlet box.

3. Slide the canopy up to hanger bracket and place the key hole on

the canopy over the screw on the hanger bracket. Turn canopy until

it locks in place at the narrow section of the key holes (Fig. 6).

4. Align the circular hole on canopy with the remaining hole on the

hanger bracket. Secure by tightening the one screw previously

loosened and the one previously removed.

5. Adjust the canopy screws as necessary until the canopy and

canopy cover are snug.

WARNING: Make sure tab at bottom of hanger bracket

is properly seated in groove of hanger ball before attaching

canopy to bracket. Failure to properly seat tab in groove could

cause damage to electrical wiring.

1. Remove one of the three mounting plate screws from the

mounting ring and loosen the other two screws (do not remove).

2. Place the key holes in the mounting plate over the two screws

previously loosened from the mounting ring. Turn the mounting

plate until the adapter plate locks in place at the narrow section

of the key holes (Fig. 7).

3. Tighten the two mounting ring screws previously loosened and

the one previously removed to secure adapter plate.

7. Installing the Adapter Plate

La page charge ...

Modern Forms FR-W1806 Cervantes Mode d'emploi

Ce manuel convient également à

Modern Forms FR-W1806 Cervantes Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents