Panasonic Toughbook FZ-A1 Operating Instructions Manual

Marque: Panasonic

Modèle: Toughbook FZ-A1

Taper: Operating Instructions Manual

Ce manuel convient également à

For further information about

this computer, you can refer

to the on-screen manual by

performing the following

steps.

Touch

- [ OnlineManual].

When more than one on-

screen manuals are prepared,

name of those manuals are

listed in above step. Touch

a manual to access from the

list.

OPERATING INSTRUCTIONS

Tablet Computer

Model No. FZ-A1 series

Please read these instructions carefully before using this product, and save this manual for future use.

Appendix

Specifications ............................................................... 26

LIMITED WARRANTY .................................................. 28

Troubleshooting

Troubleshooting (Basic)................................................ 23

Useful Information

Handling and Maintenance ........................................... 20

Getting Started

Introduction ................................................................... 11

Description of Parts ...................................................... 12

First-time Operation ...................................................... 14

Turning On/Off and Sleeping/Waking Up ...................... 17

Input Operation ............................................................. 18

Read Me First

Safety Precautions ..........................................................2

Regulatory Information ....................................................6

Contents

Read Me FirstGetting Started

Useful InformationTroubleshooting

Appendix

Safety Precautions

To reduce the risk of injury, loss of life, electric

shock, fire, malfunction, and damage to equipment

or property, always observe the following safety

precautions.

Explanation of symbol word panels

The following symbol word panels are used to

classify and describe the level of hazard, injury,

and property damage caused when the denotation

is disregarded and improper use is performed.

DANGER

Denotes a potential hazard that will result in

serious injury or death.

WARNING

Denotes a potential hazard that could result in

serious injury or death.

CAUTION

Denotes a hazard that could result in minor

injury.

NOTICE

Denotes a hazard that could result in property

damage.

The following symbols are used to classify and

describe the type of instructions to be observed.

This symbol is used to alert users to a

specific operating procedure that must not

be performed.

This symbol is used to alert users to a

specific operating procedure that must

be followed in order to operate the unit

safety.

WARNING

Do Not Charge the Battery Using

Methods Other Than Those Specified

If the battery is not charged using one

of the specified methods, electrolyte

leakage, generation of heat, ignition or

rupture of the battery may result.

Do Not Throw the Product Into a Fire or

Expose It to Excessive Heat

Generation of heat, ignition or rupture of

the battery may result.

Avoid Extreme Heat (Near the Fire, In

Direct Sunlight, for Example)

Electrolyte leakage, generation of heat,

ignition or rupture of the battery may

result.

Do Not Insert Sharp Objects Into the

Internal Battery, Disassemble, or

Modify It

Electrolyte leakage, generation of heat,

ignition or rupture of the battery may

result.

Do Not Apply Shocks to the Product by

Dropping It, Applying Strong Pressure

to It, etc.

Electrolyte leakage, generation of heat,

ignition or rupture of the battery may

result.

• If this product is subjected to a strong

impact, stop using it immediately.

When the battery has deteriorated,

contact your technical support office to

replace the battery

Continued use of a damaged battery

may result in heat generation, ignition or

battery rupture.

Read Me First

WARNING

If a Malfunction or Trouble Occurs,

Immediately Stop Use

If a Malfunction Occurs, Immediately

Unplug the AC Plug

• This product is damaged

• Foreign object is inside this product

• Smoke emitted

• Unusual smell emitted

• Unusually hot

Continuing to use this product while any

of the above conditions are present may

result in fire or electric shock.

• If a malfunction or trouble occurs,

immediately turn the power off and

unplug the AC plug. Then contact your

technical support office for repair.

Do Not Touch This Product and Cable

When It Starts Thundering

Electric shock may result.

Do Not Connect the AC Adaptor to a

Power Source Other Than a Standard

Household AC Outlet

Otherwise, a fire due to overheating

may result. Connecting to a DC/AC

converter (inverter) may damage the AC

adaptor. On an airplane, only connect

the AC adaptor/charger to an AC outlet

specifically approved for such use.

Do Not Do Anything That May Damage

the AC Cord, the AC Plug, or the AC

Adaptor

Do not damage or modify the cord, place

it near hot tools, bend, twist, or pull it

forcefully, place heavy objects on it, or

bundle it tightly. Continuing to use a

damaged cord may result in fire, short

circuit, or electric shock.

Do Not Pull or Insert the AC Plug If

Your Hands Are Wet

Electric shock may result.

Clean Dust and Other Debris of the AC

Plug Regularly

If dust or other debris accumulates on the

plug, humidity, etc. may cause a defect in

the insulation, which may result in a fire.

• Pull the plug, and wipe it with a dry cloth.

Pull the plug if the computer is not being

used for a long period of time.

Insert the AC Plug Completely

If the plug is not inserted completely, fire

due to overheating or electric shock may

result.

• Do not use a damaged plug or loose AC

outlet.

Close the Connector Cover Tightly

When Using This Product Where Is a

Lot of Water, Moisture, Steam, Dust,

Oily Vapors, etc.

The entry of foreign matter may cause a

fire or electric shocks.

• If foreign matter has found its way inside,

immediately turn the power off and

unplug the AC cord. Then contact your

technical support office.

Do Not Disassemble This Product

You may receive an electric shock, or

foreign matter may enter and result in a

fire.

Keep microSD Memory Cards Away

from Infants and Small Children

Accidental swallowing will result in bodily

injury.

• In the event of accidental swallowing,

see a doctor immediately.

Do Not Use With Exposing the Skin To

This Product For a Long Period of Time

Using this product with exposing the

skin to the heat source of this product or

AC adaptor for a long period of time can

cause a low-temperature burn.

Do Not Turn the Volume Up To Loud

When Using Headphones

Listening at high volumes that

overstimulate the ear for long periods of

time may result in loss of hearing.

CAUTION

Do Not Place This Product on Unstable

Surfaces

If balance is lost, this product may fall over

or drop, resulting in an injury.

Avoid Stacking

If balance is lost, this product may fall over

or drop, resulting in an injury.

e or

t by

ure

e to

Read Me First

Safety Precautions

CAUTION

Do Not Leave This Product in High

Temperature Environment for a Long

Period of Time

Leaving this product where it will be

exposed to extremely high temperatures

such as near fire or in direct sunlight may

deform the cabinet and/or cause trouble

in the internal parts. Continued use in

such a resulting condition may lead to

short-circuiting or insulation defects, etc.

which may in turn lead to a fire or electric

shocks.

Hold the Plug When Unplugging the AC

Plug

Pulling on the cord may damage the cord,

resulting in a fire or electric shock.

Do Not Move This Product While the

AC Plug Is Connected

The AC cord may be damaged, resulting

in fire or electric shock.

• If the AC cord is damaged, unplug the

AC plug immediately.

Use Only the Specified AC Adaptor

With This Product

Using an AC adaptor other than the one

supplied (supplied with the unit or one

sold separately as an accessory) may

result in a fire.

Do Not Subject the AC Adaptor To Any

Strong Impact

Using the AC adaptor after a strong

impact such as being dropped may result

in electric shock, short circuit, or fire.

Take a Break Of 10-15 Minutes Every

Hour

Using this product for long periods of time

may have detrimental health effects on

the eyes or hands.

Do Not Expose the Skin To This

Product When Using the Product In A

Hot Or Cold Environment

Burns, low-temperature burns, or frostbite

may result.

• When it is necessary to expose the

skin to this product such as to scan a

fingerprint, perform the operation in the

shortest time possible.

NOTICE

 Do not place the computer near a television or

radio receiver.

 Keep the computer away from magnets. Data

stored on the flash memory may be lost.

 This computer is not intended for the display of

images for use in medical diagnosis.

 This computer is not intended for a use with

connection of medical equipment for the purpose

of medical diagnosis.

 Panasonic shall not be liable for loss of data

or other incidental or consequential damages

resulting from the use of this product.

 If this computer will not be used for a long period

of time (a month or more), charge or discharge

(use) the battery until the remaining battery level

becomes 30 % to 40 % and store the product in

a cool, dry place.

 This computer prevents overcharging of the

battery by recharging only when the remaining

power is less than approx. 95 % of capacity.

 The battery is not charged when this computer

is first purchased. Be sure to charge it before

using it for the first time. When the AC adaptor

is connected to this computer, charging begins

automatically.

 Should the battery leak and the fluid get into your

eyes, do not rub your eyes. Immediately flush

your eyes with clear water and see a doctor for

medical treatment as soon as possible.

NOTE

 The battery may become warm during

recharging or normal use. This is completely

normal.

 Recharging will not commence if internal

temperature of the battery is outside of the

allowable temperature range (0 °C to 50 °C).

Once the allowable range requirement is

satisfied, charging begins automatically. Note

that the recharging time varies based on the

usage conditions. (Recharging takes longer than

usual when the temperature is 10 °C or below.)

 If the temperature is low, the operating time is

shortened. Only use the computer within the

allowable temperature range.

 The battery is a consumable item. If the amount

of time the computer can be run by using a

particular battery becomes dramatically shorter

and repeated recharging does not restore its

performance, the battery should be replaced with

a new one. Contact your technical support office.

 Al

in u

rem

THIS

AS,

EQU

DEV

WIT

PAN

FOR

USE

THE

(

Pan

tec

Smo

requ

med

spec

The

This

equi

contr

syste

or sa

in an

the u

devi

This

mini

(e.g.,

is pr

precis

hand

Read Me First

y of

pose

eriod

rge

evel

ct in

ter

tor

your

for

than

w.)

ount

rter

d with

ffice.

 Always power off the computer when it is not

in use. Leaving the computer on when the

AC adaptor is not connected will exhaust the

remaining battery capacity.

THIS PRODUCT IS NOT INTENDED FOR USE

AS, OR AS PART OF, NUCLEAR EQUIPMENT/

SYSTEMS, AIR TRAFFIC CONTROL

EQUIPMENT/SYSTEMS, AIRCRAFT COCKPIT

EQUIPMENT/SYSTEMS *

, MEDICAL DEVICES

OR ACCESSORIES *

, LIFESUPPORT

SYSTEMS OR OTHER EQUIPMENTS/

DEVICES/SYSTEMS THAT ARE INVOLVED

WITH ENSURING HUMAN LIFE OR SAFETY.

PANASONIC WILL NOT BE RESPONSIBLE

FOR ANY LIABILITY RESULTING FROM THE

USE OF THIS PRODUCT ARISING OUT OF

THE FOREGOING USES.

AIRCRAFT COCKPIT EQUIPMENT/

SYSTEMS include Class2 Electrical Flight

Bag (EFB) Systems and Class1 EFB Systems

when used during critical phases of flight (e.g.,

during take-off and landing) and/or mounted

on to the aircraft. Class1 EFB Systems and

2 EFB Systems are defined by FAA: AC

(Advisory Circular) 120-76A or JAA: JAA TGL

(Temporary Guidance Leaflets) No.36.

As defined by the European Medical Device

Directive (MDD) 93/ 42/EEC.

Panasonic cannot guarantee any specifications,

technologies, reliability, safety (e.g. Flammability/

Smoke/Toxicity/Radio Frequency Emission, etc)

requirements related to aviation standards and

medical equipment standards that differ from the

specifications of our COTS (Commercial-Off-

The-Shelf) products.

This computer is not intended for use in medical

equipment including life-support systems, air traffic

control systems, or other equipment, devices or

systems that are involved with ensuring human life

or safety. Panasonic cannot be held responsible

in any way for any damages or loss resulting from

the use of this unit in these types of equipment,

devices or systems, etc.

This computer has been designed so as to

minimize shock to the LCD, the leakage of liquid

(e.g., water) on to the buttons, etc., but no warranty

is provided against such trouble. Therefore, as a

precision instrument, be extremely careful in the

handling.

Read Me First

Regulatory Information

Information to the User

This product and your Health

This product, like other radio devices, emits radio

frequency electromagnetic energy. The level of

energy emitted by this product however is far much

less than the electromagnetic energy emitted by

wireless devices like for example mobile phones.

Because this product operates within the

guidelines found in radio frequency safety

standards and recommendations, we believe

this product is safe for use by consumers. These

standards and recommendations reflect the

consensus of the scientific community and result

from deliberations of panels and committees of

scientists who continually review and interpret the

extensive research literature.

In some situations or environments, the use of

this product may be restricted by the proprietor of

the building or responsible representatives of the

organization. These situations may for example

include:

 Using this product on board of airplanes, or

 In any other environment where the risk of

interference to other devices or services is

perceived or identified as harmful.

If you are uncertain of the policy that applies on the

use of wireless devices in a specific organization

or environment (e.g. airports), you are encouraged

to ask for authorization to use this product prior to

turning on the product.

Regulatory Information

We are not responsible for any radio or television

interference caused by unauthorized modification

of this product. The correction of interference

caused by such unauthorized modification will be

the responsibility of the user. We and its authorized

resellers or distributors are not liable for damage or

violation of government regulations that may arise

from failing to comply with these guidelines.

26-M-1

Lithium Battery

Lithium Battery!

This computer contains a lithium battery to enable

the date, time, and other data to be stored. The

battery should only be exchanged by authorized

service personnel.

Warning! A risk of explosion from incorrect

installation or misapplication may possibly occur.

15-E-1

Pile au lithium!

Le micro-ordinateur renferme une pile au lithium

qui permet de sauvegarder certaines données,

notamment la date et l’heure. La pile ne doit être

remplacée que par un technicien qualifié.

Danger!

Risque d’explosion en cas de non respect de cette

mise en garde!

15-F-1

Information for Users on

Collection and Disposal

of Old Equipment and

used Batteries

These symbols on the products,

packaging, and/or accompanying

documents mean that used electrical

and electronic products and batteries

should not be mixed with general

household waste.

For proper treatment, recovery and recycling of

old products and used batteries, please take them

to applicable collection points, in accordance

with your national legislation and the Directives

2002/96/EC and 2006/66/EC.

By disposing of these products and batteries

correctly, you will help to save valuable resources

and prevent any potential negative effects on

human health and the environment which could

otherwise arise from inappropriate waste handling.

For more information about collection and recycling

of old products and batteries, please contact your

local municipality, your waste disposal service or

the point of sale where you purchased the items.

Penalties may be applicable for incorrect disposal

of this waste, in accordance with national

legislation.

For business users in the European Union

If you wish to discard electrical and electronic

equipment, please contact your dealer or supplier

for further information.

[Information on Disposal in other

Countries outside the European

Union]

These symbols are only valid in the

European Union. If you wish to discard

this product, please contact your local

authorities or dealer and ask for the

correct method of disposal.

<Only

The f

durin

or re

WAN

termi

infor

to inc

supp

thes

desig

produ

custo

Read Me First

tre

cette

5-F-1

hem

ces

ling.

ycling

our

ms.

osal

plier

ard

cal

Note for the battery symbol (bottom

two symbol examples):

This symbol might be used in

combination with a chemical symbol.

In this case it complies with the

requirement set by the Directive for the

chemical involved.

53-E-1

Safety Precautions for

wireless WAN

The following safety precautions must be observed

during all phases of the operation, usage, service

or repair of any Computer incorporating wireless

WAN modem. Manufacturers of the cellular

terminal are advised to convey the following safety

information to users and operating personnel and

to incorporate these guidelines into all manuals

supplied with the product. Failure to comply with

these precautions violates safety standards of

design, manufacture and intended use of the

product. Panasonic assumes no liability for

customer failure to comply with these precautions.

When in a hospital or other health care

facility, observe the restrictions on

the use of mobiles. Switch Computer

incorporating wireless WAN modem off,

if instructed to do so by the guidelines

posted in sensitive areas. Medical

equipment may be sensitive to RF

energy.

The operation of cardiac pacemakers,

other implanted medical equipment

and hearing aids can be affected

by interference from Computer

incorporating wireless WAN modem

placed close to the device. If in doubt

about potential danger, contact the

physician or the manufacturer of the

device to verify that the equipment is

properly shielded. Pacemaker patients

are advised to keep their Computer

incorporating wireless WAN modem

away from the pacemaker, while it is on.

Switch off Computer incorporating

wireless WAN modem before boarding

an aircraft. Make sure it cannot be

switched on inadvertently. The operation

of wireless appliances in an aircraft is

forbidden to prevent interference with

communications systems. Failure to

observe these instructions may lead

to the suspension or denial of cellular

services to the offender, legal action, or

both. For details on usage of this unit

in aircrafts please consult and follow

instruction provided by the airline.

Do not operate Personal Computer

or Handheld Computer incorporating

wireless WAN modem in the presence

of flammable gases or fumes. Switch off

the cellular terminal when you are near

petrol stations, fuel depots, chemical

plants or where blasting operations are

in progress. Operation of any electrical

equipment in potentially explosive

atmospheres can constitute a safety

hazard.

Your Computer incorporating wireless

WAN modem receives and transmits

radio frequency energy while switched

on. Remember that interference can

occur if it is used close to TV sets,

radios, computers or inadequately

shielded equipment. Follow any

special regulations and always switch

off Computer incorporating wireless

WAN modem wherever forbidden, or

when you suspect that it may cause

interference or danger.

Road safety comes first! Do not use a

Computer incorporating wireless WAN

modem while driving a vehicle. Do

not place the computer with wireless

WAN modem in an area where it could

cause personal injury to the driver or

passengers. It is recommended to stow

the unit in the boot or secure stowage

area while driving. Do not place the

computer with wireless WAN modem

in an area over an air bag or in the

vicinity where an air bag may deploy. Air

bags inflate with great force and if the

computer with wireless WAN modem is

placed in the air bag deployment area

may be propelled with great force and

cause serious injury to occupants of the

vehicle.

IMPORTANT!

Computer incorporating wireless WAN

modem operate using radio signals

and cellular networks cannot be

guaranteed to connect in all conditions.

Therefore, you should never rely

solely upon any wireless device for

essential communications, for example

Read Me First

Regulatory Information

This

oper

FCC

the f

the p

Mobi

alloc

and 5

can c

produ

Resp

Amer

One

Sec

Tel N

USA

com

For

visi

http

or c

CAU

Risk

Inco

Disp

Instr

ATT

Il y a

rem

Met

conf

L’ap

alim

Pou

de l

1-80

emergency calls. Remember, in order

to make or receive calls, Computer

incorporating wireless WAN modem

must be switched on and in a coverage

area with adequate cellular signal

strength. Some networks do not allow

for emergency calls if certain network

services or phone features are in

use (e.g. lock functions, fixed dialing

etc.). You may need to deactivate

those features before you can make

an emergency call. Some networks

require that a valid SIM card be properly

inserted in Computer incorporating

wireless WAN modem.

Camera Light

CAUTION

Camera Light for rear camera

- The light from the LED is strong and can injure

human eyes. Do not look directly at the LEDs with

naked eyes.

57-E-1

For U.S.A.

Federal Communications Commission Radio

Frequency Interference Statement

Note: This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment generates,

uses and can radiate radio frequency energy

and, if not installed and used in accordance with

the instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to

try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment

and receiver.

 Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

 Consult the Panasonic Service Center or an

experienced radio/TV technician for help.

Warning

To assure continued compliance, use only shielded

interface cables when connecting to a computer

or peripheral. Also, any changes or modifications

not expressly approved by the party responsible

for compliance could void the user’s authority to

operate this equipment.

This device complies with Part 15 of the FCC

Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful

interference, and

(2) This device must accept any interference

received, including interference that may cause

undesired operation.

FCC RF Exposure Warning:

 This device meets the government’s

requirements for exposure to radio waves.

This device is designed and manufactured not

to exceed the emission limits for exposure to

radio frequency (RF) energy set by the Federal

Communications Commission of the U.S.

Government.

 This equipment has been approved for portable

operation, and does not require any minimum

spacing be provided between antennas and

all person’s body. This equipment may not be

colocated or operated with any other antenna or

transmitter.

 The exposure standard for wireless device

employs a unit of measurement known as the

Specific Absorption Rate, or SAR. The SAR limit

set by the FCC is 1.6 W/kg.

* Tests for SAR are conducted using standard

operating positions accepted by the FCC with

the device transmitting at its highest certified

power level in all tested frequency bands.

Although the SAR is determined at the highest

certified power level, the actual SAR level of

the device while operating can be well below

the maximum value. This is because the

device is designed to operate at multiple power

levels so as to use only the poser required to

reach the network. In general, the closer you

are to a wireless base station antenna, the

lower the power output.

 The FCC has granted an Equipment

Authorization for this device with all reported

SAR levels evaluated as in compliance with the

FCC RF exposure guidelines. SAR information

on this device is on file with the FCC and can be

found under the Display Grant section of www.

fcc.gov/oet/ea/fccid after searching on FCC ID:

ACJ9TGFZ-A12.

25-M-4

Read Me First

This product is restricted to indoor use due to its

operation in the 5.15 to 5.25 GHz frequency range.

FCC requires this product to be used indoors for

the frequency range 5.15 to 5.25 GHz to reduce

the potential for harmful interference to co-channel

Mobile Satellite systems. High power radars are

allocated as primary users of the 5.25 to 5.35 GHz

and 5.65 to 5.85 GHz bands. These radar stations

can cause interference with and /or damage this

product.

25-M-W-4

Responsible Party: Panasonic Corporation of North

America

One Panasonic Way

Secaucus, NJ 07094

Tel No:1-800-LAPTOP5 (1-800-527-8675)

6-M-1

USA Only: Disposal may be regulated in your

community due to environmental considerations.

For disposal or recycling information, please

visit Panasonic website:

http://www.panasonic.com/environmental

or call 1-888-769-0149

65-M-2

CAUTION:

Risk of Explosion if Battery is replaced by an

Incorrect Type.

Dispose of Used Batteries According to the

Instructions.

58-E-1

ATTENTION:

Il y a risque d’explosion si la batterie est

remplacée par une batterie de type incorrect.

Mettre au rebut les batteries usagées

conformément aux instructions.

58-F-1

A lithium ion battery that is

recyclable powers the

product you have

purchased.

Please call

1-800-8-BATTERY for

information on how to

recycle this battery.

L’appareil que vous vous êtes procuré est

alimenté par une batterie au lithium-ion.

Pour des renseignements sur le recyclage

de la batterie, veuillez composer le

1-800-8-BATTERY.

48-M-1

For Canada

Canadian ICES-003

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

7-M-2

Industry Canada

This product complies with RSS210 Industry Canada.

Operation is subject to the following two conditions;

(1) this device may not cause interference, and

(2) this device must accept any interference,

including interference that may cause

undesired operation of the device.

30-Ca-1-1

Industrie Canada

Cet équipement est conforme à la norme CNR-

210 d’Industrie Canada. Son fonctionnement est

soumis aux deux conditions suivantes :

(1) ce dispositif ne peut produire de brouillage, et

(2) ce dispositif doit accepter le brouillage, y

compris le brouillage pouvant entraîner le

fonctionnement non déiré de l’appareil.

30-Ca-1

This product (local network devices) for the band

5150- 5250 MHz is only indoor usage to reduce

potential for harmful interference to co-channel

Mobile Satellite systems. High power radars are

allocated as primary users (meaning they have

priority) of 5250-5350 MHz and 5650-5850 MHz

and these radars could cause interference and/or

damage to LELAN devices.

Cet appareil (pour réseaux locaux radioélectriques)

dans les bandes de fréquences 5150-5250 MHz

est réservé à une utilisation à l’intérieur afin de

réduire le risque d’interférence avec les systèmes

satellites mobiles bicanaux.

Les radars forte puissance sont désignés comme

étant les premiers utilisateurs (c’est-à-dire qu’ils

ont la priorité) des bandes de fréquences 5250-

5350 MHz et 5650-5850 MHz. Ces stations radars

peuvent provoquer des interférences et/ou des

dommages à ce périphérique.

30-Ca-2-1

 This computer complies with Industry Canada

radiation exposure limits set forth for an

uncontrolled environment.

 This PC with WLAN and/or Bluetooth

transmitters installed, has been approved for

portable operation and does not require any

minimum spacing be provided between antennas

and all person’s body.

elded

ons

tions:

ause

eral

able

a or

limit

ard

with

hest

ower

d to

the

n be

ww.

ID:

5-M-4

Read Me First

Regulatory Information

 Cet équipement est conforme aux limites

d’exposition aux rayonnements d’Industrie

Canada établies pour un environnement non

contrôlé.

 Ce PC avec émetteurs WLAN et/ou Bluetooth

a été approuvé à des fins d’opération mobile;

aucun espace minimum entre les antennes et le

corps de l’utilisateur n’est requis.

25-Ca-1

FOR USE WITH MODEL NO. :

FZ-AA2202B

POUR UTILISER AVEC MODÈLE :

FZ-AA2202B

20-Ca-1

For Europe

<Only for model with a “ ” mark on the

bottom of the computer>

Declaration of Conformity

(DoC)

“Hereby, Panasonic

declares that this

Personal Computer is in

compliance with the essential requirements and

other relevant provisions of the Directive 1999/5/

EC.”

Hint:

If you want to get a copy of the original DoC of our

above mentioned products, please contact our web

address: http://www.doc.panasonic.de

Authorised Representative:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Indication of the countries where WLAN is intended

to be used:

AT BE BG CH CY CZ DE DK EE ES

FI FR GB GR HU IE IS IT LT LU

LV MT NL NO PL PT RO SE SI SK TR

18-25-E-0

Interface Cable

Use of an interface cable longer than 3 m

{ 9.84 feet } is not recommended.

11-E-1

For UK

For your safety, please read the following text

carefully.

This appliance is supplied with a molded three pin

mains plug for your safety and convenience.

A 3 ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure

that the replacement fuse has a rating of 3 ampere

and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark

A S A

or the BSI mark

on the body of the fuse.

If the plug contains a removable fuse cover you

must ensure that it is refitted when the fuse is

replaced.

If you lose the fuse cover the plug must not be

used until a replacement cover is obtained. A

replacement fuse cover can be purchased from

your local dealer.

If the fitted molded plug is unsuitable for the

socket outlet in your home then the fuse should

be removed and the plug cut off and disposed of

safely.

There is a danger of severe electrical shock if the

cut off plug is inserted into any 13-ampere socket.

How to replace the fuse

The location of the fuse differs according to the

type of AC mains plug (figures A and B).

Confirm the AC mains plug fitted and follow the

instructions below. Illustrations may differ from

actual AC mains plug.

Open the fuse cover with a screwdriver and

replace the fuse and close or attach the fuse cover.

Fuse cover

Figure A Figure B

For India

For the purpose of recycling to facilitate

effective utilization of resources, please

return this product to a nearby

authorized collection center, registered

dismantler or recycler, or Panasonic service center

when disposing of this product.

Please see the Panasonic website for further

information on collection centers, etc.

http://www.panasonic.co.in/wps/portal/home

Read Me First

Thank you for purchasing this Panasonic product.

For optimum performance and safety, please read

these instructions carefully.

Terms and Illustrations

in These Instructions



Page in these Operating Instructions

or in the Reference Manual.

Reference to the on-screen manuals.

 Some illustrations are simplified to help your

understanding and may look different from the

actual unit.

 Refer for the latest information about optional

products to the catalogs, etc.

Disclaimer

Computer specifications and manuals are subject

to change without notice. Panasonic Corporation

assumes no liability for damage incurred directly or

indirectly from errors, omissions or discrepancies

between the computer and the manuals.

Trademarks / Licenses

 Google, the Google logo, Google Search, Gmail,

Android and Google Play are trademarks of

Google, Inc.

 Marvell and the Marvell logo are registered

trademarks of Marvell and/or its affiliates.

 microSDHC Logo is a trademark of SD-3C, LLC.

 HDMI, the HDMI Logo and High-Definition

Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing LLC in

the United States and other countries.

 Adobe, the Adobe logo and Adobe Reader are

either registered trademarks or trademarks

of Adobe Systems Incorporated in the United

States and/or other countries.

 Bluetooth

is a registered trademark owned

by Bluetooth SIG, Inc., U.S.A. and licensed to

Panasonic Corporation.

 Names of products, brands, etc., appearing

in this manual are trademarks or registered

trademarks of their respective own companies.

 This product is licensed under the AVC Patent

Portfolio License, VC-1 Patent Portfolio License

and MPEG-4 Visual Patent Portfolio License

for the personal use of a consumer or other

uses in which it does not receive remuneration

to (i) encode video in compliance with the AVC

Standard, VC-1 Standard and MPEG-4 Visual

Standard (“AVC/VC-1/MPEG-4 Video”) and/or

(ii) decode AVC/VC-1/MPEG-4 Video that was

encoded by a consumer engaged in a personal

activity and/or was obtained from a video

provider licensed to provide AVC/VC-1/MPEG-4

Video. No license is granted or shall be implied

for any other use. Additional information may be

obtained from MPEG LA, LLC. See http://www.

mpegla.com.

Introduction

Getting Started

Description of Parts

Front Side

HF I J K

Wireless WAN Antenna



Reference Manual “Wireless

Communication - Wireless WAN”

Ambient light sensor



Reference Manual “Settings - Using

Dashboard”

Front camera



Reference Manual “Photos and

Videos”

LCD

 “Input Operation” (page 18), “Home

Screen” (page 19)

Wi-Fi antenna / Bluetooth antenna



Reference Manual “Wireless

Communication - Wi-Fi”, “Wireless

Communication - Bluetooth”

Magnet sensor



Reference Manual “Settings - Using

Settings Application - Display”

Microphone

 Reference Manual “Input Operation -

Voice Input”

Menu button

 “Input Operation” (page 18)

Home button

 “Input Operation” (page 18)

Back button

 “Input Operation” (page 18)

USER button

 “Input Operation” (page 18)

Battery indicator



Reference Manual “Battery Power -

Checking the Battery Status”

Power switch

 “Turning On/Off and Sleeping/Waking

Up” (page 17)

Getting Started

Rear Side

Camera light

 Reference Manual “Photos and

Videos”

Rear camera



Reference Manual “Photos and

Videos”

C Reset switch

HDMI Micro connector

 Reference Manual “Connections -

External Display”

Headphone/microphone jack

microSD memory card slot

 Reference Manual “Connections -

MicroSD Memory Card”

USB 2.0 Micro-B connector

 Reference Manual “Connections -

USB Connection”

H Speaker

SIM card slot



Reference Manual “Wireless

Communication - Wireless WAN”

J DC-IN jack

Expansion Bus Connector (Use as an

extension in the future)

Pen holder

( page 14)

Security lock

A Kensington cable can be connected.

For further information, read the manual that

comes with the cable.

CAUTION

When closing the DC-IN jack cover, push the cover

straight.

Otherwise, the cover may be damaged.

Correct Incorrect

D E F

on -

r -

Getting Started

First-time Operation

Preparation

Check and identify the supplied

accessories.

If you do not find the described accessories,

contact your technical support office.

AC Adaptor…1

Model No.

FZ-AA2202B

AC Cord…1

(Shape depends on

the country)

Digitizer Pen…1

(At the time of

purchase, the digitizer

pen is put in the pen

holder ( page 13).)

Tether…1

Soft Cloth…1

OPERATING INSTRUCTIONS

(This book)…1

To prevent the digitizer pen

falling accidentally, attach the

digitizer pen to this computer

using the tether.

1. Pass one of the loops through the hole of the

digitizer pen.

2. Pass one of the loops through the second

loop on the tether.

3. Thread the second loop on the tether to the

hole as illustrated.

4. Pass the digitizer pen through the second

loop on the tether as illustrated.

NOTE

 When the digitizer pen is not used, hook the

tether as illustrated.

Getting Started

Starting Up

Connect this computer to a

power outlet.

The battery charging starts automatically.

CAUTION

 Do not disconnect the AC adaptor until the

first-time operation procedure is completed.

 When using this computer for the first

time, do not connect any peripheral device

except the AC adaptor.

 Handling the AC adaptor

• Problems such as sudden voltage drops

may arise during periods of thunder and

lightning. Since this could adversely affect

this computer, an uninterruptible power

source (UPS) is highly recommended

unless running from the battery alone.

Press (Power switch).

After the battery indicator blinks 3 times, this

tablet computer starts up.

If necessary, touch the

language name and scroll the

language list, then touch the

language you use.

㪜㫅㪾㫃㫀㫊㪿㩿㪬㫅㫀㫋㪼㪻㩷㪪㫋㪸㫋㪼㫊㪀

㪜㫊㫇㪸㬧㫆㫃

㪝㫉㪸㫅

ç㪸㫀㫊㩿㪙㪼㫃㪾㫀㫈㫌㪼㪀

㪝㫉㪸㫅

ç㪸㫀㫊㩿㪚㪸㫅㪸㪻㪸㪀

㪝㫉㪸㫅

ç㪸㫀㫊㩿㪝㫉㪸㫅㪺㪼㪀

㪝㫉㪸㫅

ç㪸㫀㫊㩿㪪㫌㫀㫊㫊㪼㪀

㪠㫋㪸㫃㫀㪸㫅㫆㩿㪠㫋㪸㫃㫀㪸㪀

㪠㫋㪸㫃㫀㪸㫅㫆㩿㪪㫍㫀㫑㫑㪼㫉㪸㪀

㪥㪼㪻㪼㫉㫃㪸䌮㪻㫊㩿㪙㪼㫃㪾㫀㬡㪀

㪥㪼㪻㪼㫉㫃㪸䌮㪻㫊㩿㪥㪼㪻㪼㫉㫃㪸㫄㪻㪀

㪥㫆㫉㫊㫂㩷㪹㫆㫂㫄㬛㫃

Touch [Start].

If “SIM card not found” is displayed, touch

[Skip]. Then touch [Skip] or configure

wi-fi settings by following the on-screen

instructions.

Touch and scroll the time zone

list and touch the time zone for

your location.

If necessary, set date and time or set

[Automatic date & time] to [ON].

Touch [Next].

“Sign in with your Google Account” screen is

displayed.

If necessary, set up your

Google account by following

the on-screen instructions.

 If you set up your Google account, you can

use Gmail, Calendar, etc.

When “Use Google location”

is displayed, touch the Google

location services to enable/

disable them, and touch [Next].

When “This tablet belongs to...”

is displayed, input your name

and touch [Next].

Read “Google services” and

touch [Next].

When “Setup complete” is

displayed, touch [Finish].

k the

Getting Started

First-time Operation

At the

autom

turn o

opera

When “Make yourself at home”

is displayed, touch [OK].

Getting Started

Turning On/Off and Sleeping/Waking Up

Turning On

Press (Power switch).

Drag to or .

When dragging to , Camera application

will start.

CAUTION

 Do not press the power switch repeatedly.

 Once you turn off this computer, wait for

10 seconds or more before you turn it on

again.

 Do not perform the following operation until

the home screen is displayed.

• Connecting or disconnecting the AC

adaptor

• Pressing the power switch

• Touching the screen or buttons

Turning Off

Press and hold (Power

switch) until “Power off” screen

is displayed.

Touch “OK”.

Sleeping

At the time of purchase, the screen turns off

automatically after 1 minute with no operation. To

turn off the screen manually, perform the following

operation.

Press (Power switch).

The screen turns off.

NOTE

 The screen turns off automatically after

1 minute. You can change time to turn the

screen off by touching

[

Settings] - [ Display] - [Sleep].

Waking Up

Press (Power switch).

The lock screen is displayed.

Drag to or .

When dragging to , Camera application

will start.

NOTE

 Some applications (“Clock” etc.) will appear

before the lock screen is displayed. After

that application is closed, the lock screen is

displayed.

Getting Started

Input Operation

Screen Input Operation

Touch Select items or options.

Touch and hold Open special options.

Drag Scroll the screen.

Flick

Scroll the screen

quickly.

Drag and drop Move an item.

Pinch

Zoom in or out the

screen.

Depending on the

applications, you can

also zoom in or out by

double-touching the

screen.

Using the Digitizer Pen

You can operate “Touch”, “Touch and hold”,

“Drag”, “Flick”, “Drag and drop” and “Double-tap”

by using the included digitizer pen instead of your

finger.

 Without pressing the digitizer button (A):

Touch the screen with the digitizer pen.

 While pressing the digitizer button (A):

Close the digitizer pen to the screen.

CAUTION

 The tip of the digitizer pen (B) is equipped with

a sensor. Continued applied pressure to the

tip may result in its malfunction or degradation.

Make sure excessive pressure is not applied to

the tip when storing the digitizer pen.

Digitizer Calibration

If necessary, perform the digitizer calibration by

following steps below.

Perform the calibration for the orientation to be

used.

Touch - [ Pen Calibration].

Using the digitizer pen, touch

each target one by one.

Touch [Finished].

Buttons

Select additional functions.

The same function as [

Return to the home screen.

The same function as [

Return to the previous screen.

The same function as [

 Press within 1 second :

Enter security mode (sound off, screen

off and lock). To return from security

mode, press

(Power switch).

 Press for more than 1 second :

Launch “Dashboard”.

 Press and hold

(USER button), then

press

(Menu button) within 1 second:

Take screenshot

The screenshot data will be stored in

the following folder.

/sdcard/Pictures/Screenshots/

Getting Started

Home Screen

EBCD F

A Search / Voice search

Search the internet and this computer using

Google search. You can input the search

terms by using on-screen keyboard or

speaking.

B Widgets

The small applications on the home screen.

Some widgets display the latest information

(clock, calendar, weather, email, etc.) on the

home screen.

C Application shortcuts

Open an application. You can add/remove

applications shortcuts to/from the home

screen.

D Home screen

The starting point for this computer. You can

place shortcuts, widgets and other items to

the home screen.

Apps

Display all applications and widgets. Touch an

application/widget to open from the list.

Depending on the applications,

displayed at the top-right of the screen. You

can select additional functions from the menu.

Recent apps

Display the recent applications. Touch an

application to open from the application list.

To stop the application, drag it to the right.

Home

Return to the home screen.

Back

Return to the previous screen.

J Status detail and quick settings

Touch this area to open the status detail

(notification icons, status icons and clock)

(

Reference Manual “Home Screen -

Notification Icons”, “Home Screen - Status

Icons”). Touch the status detail to open the

quick settings. The quick settings display

network status, remaining battery charge and

other details.

When you touch [

Settings], Settings

application is opened.

K Panels

This computer has 5 panels. Flick left or right

to display the next panel.

n].

hen

ond:

Getting Started

Operation Environment

 Place this computer on a flat stable surface. If

this computer is exposed to an extremely strong

impact, it may become damaged.

 Temperature :

Operation : -10 °C to 50 °C {14 °F to 122 °F}

(IEC60068-2-1, 2)*

Storage : -20 °C to 60 °C {4 °F to 140 °F}

Humidity :

Operation : 30 % to 80 % RH

(No condensation)

Storage : 30 % to 90 % RH (No condensation)

Even within the above temperature/humidity

ranges, using for a long time in an extreme

environment will result in the product

deterioration and will shorten the product life.

If this computer is wet in temperatures of 0 °C or

below, freeze damage may occur. Make sure to

dry off this computer in such temperatures.

Do not expose the skin to this product when

using the product in a hot or cold environment.

( page 4)

 Do not place this computer in the following

areas, otherwise the computer may be damaged.

• Near electronic equipment. Image distortion or

noise may occur.

• In extremely high or low temperature.

 As this computer can become hot during

operation, keep it away from items that are

sensitive to heat.

Handling Cautions

This computer is designed to minimize shock to

parts such as the LCD and the flash memory drive,

but no warranty is provided against any trouble

caused by shock. Be extremely careful when

handling this computer.

 When carrying this computer :

• Turn off this computer.

• Remove all external devices, cables and other

protruding objects.

• Do not drop or hit this computer against solid

objects.

• Do not grip the display part.

 When you board an airplane, take this computer

with you and never put it in your checked

luggage. When using this computer on airplane,

follow the airline’s instructions.

 Use only the included digitizer pen or finger to

touch the screen. Do not place any object on

its surface and do not press down strongly with

sharp-pointed or hard objects that may leave

marks (e.g., nails, pencils and ball point pens).

 Do not use the screen when dust or dirt (e.g., oil)

is on the screen. Otherwise foreign particles on

the screen/digitizer pen can scratch the screen

surface or obstruct the digitizer pen operation.

 Use the digitizer pen only for touching the

screen. Using it for any other purpose may

damage the digitizer pen and result in scratches

on the screen.

When Using Peripheral Devices

Follow these instructions and the Reference

Manual to avoid any damage to the devices.

Carefully read the instruction manuals of the

peripheral devices.

 Use the peripheral devices conforming to this

computer’s specifications.

 Connect to the connectors in the correct

direction.

 If it is hard to insert, do not try forcibly but check

this computer’s shape, direction, alignment of

pins, etc.

 Remove the cables when you carry this

computer. Do not pull the cables forcibly.

Preventing This Computer from

Unauthorized Use via Wireless

Networks

 Before using Wi-Fi/Bluetooth/wireless WAN*

make the appropriate security settings such as

data encryption.

Only for model with wireless WAN.

Maintenance

To Clean the LCD Panel

 When the screen becomes dirty, wipe it with an

approved soft cloth.

The screen is specially treated to prevent dirt

from adhering to the surface, so dirt can be

removed easily using a dry cloth (use only the

approved soft cloth).

Remove the dirt, water, etc. as soon as possible.

Otherwise, the LCD panel is stained or changes

in quality.

If the dirt does not come off easily, breathe on

the surface and try again.

 Suggestions About Cleaning the LCD Surface

To improve the outdoor visibility of the display, a

low reflection coating has been added. In order

Handling and Maintenance

to a

app

the

this

pro

• B

•

How

• Use

wat

• Fir

adh

the

sur

part

Nex

of th

Afte

the

for

 Cle

off.

Cle

cau

the

pow

 Wa

mil

If t

cle

 Ch

• A

• Is

• A

• Is

Useful Information

La page charge ...

Panasonic Toughbook FZ-A1 Operating Instructions Manual

Marque: Panasonic

Modèle: Toughbook FZ-A1

Taper: Operating Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Panasonic Toughbook FZ-A1

Panasonic Toughbook FZ-A1 Operating Instructions Manual

Ce manuel convient également à

Panasonic Toughbook FZ-A1 Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents