ZyXEL Printer NPS-520 Manuel utilisateur

NPS-520

MFP Print Server

Quick Start Guide

Version 1.00

Edition 2

1/2007

Table of Contents

ENGLISH 1

DEUTSCH 19

ESPAÑOL 39

FRANÇAIS 59

ITALIANO 79

РУССКИЙ 99

SVENSKA 119

ENGLISH

1

Overview

The NPS-520 is a print server and comes with one Ethernet

port and one USB (v2.0) port. You can use the USB port to

share a printer with the computers in the network to which the

NPS-520 (labeled NPS in the following graphic) is connected.

Through the NPS-520, the printer works as if it is connected

directly to your computer.

" You should have already installed the driver

(and utility if there is one) for the printer

(connected to the NPS-520) on your computer.

Refer to your printer documentation for more

information.

This guide shows you how to:

1 Install the hardware.

2 Install and use the ZyXEL utility (Windows users only).

ENGLISH

2

ENGLISH

3 Use the web configurator to manage the NPS-520.

Windows users can use the utility or web configurator to

configure the NPS-520. Macintosh and Linux/UNIX users can

use the web configurator to configure the NPS-520. See page

16 for a list of system requirements.

" If your computer operating system version is

older than Windows 2000 SP4, you can only

print on a printer even if the printer provides

print, copy, fax and/or scan functions.

1 Hardware Connection

Follow the steps below to connect the NPS-520 to your

network.

ENGLISH

3

1 Connect the USB port to a USB v2.0 compliant printer

using a USB cable.

2 Connect the LAN port to your local network using an

Ethernet cable.

3 Use the included power adaptor to connect the power

socket on the NPS-520 to an appropriate power source.

1.1 LEDs

Look at the LEDs (lights) on

the top panel.

The READY LED stays on

when the system is ready.

The LAN LED stays on if the

LAN port is properly

connected and blinks when

there is traffic.

V If none of the LEDs are on, check your

connections, and inspect your cables for

damage. If the LEDs are still off, contact your

local vendor.

4

ENGLISH

2 ZyXEL Utility

Use the utility to install and associate your printer driver as

well as manage the NPS-520.

2.1 Utility Installation on Windows

" The NPS-520’s default IP address is

192.168.1.6.

The installation procedures are similar for all supported

Windows versions.

1 Insert the included CD into the CD-ROM drive on your

computer (that is connected to the NPS-520 directly or

connected to your network). When the following screen

displays, click Setup.

V If the screen does not display, locate and

double-click autorun.exe on the CD.

ENGLISH

5

2 Select your preferred language and click OK.

3 The following screen displays. Click Next.

6

ENGLISH

4 Click Next to accept the default file location or click

Change to select an alternate folder.

5 Select Yes, I want to configure the ZyXEL NPS-520 now

and click Next to configure the NPS-520 now.

ENGLISH

7

6 Your unique NPS-520’s device name automatically

displays in the text box. If it does not show up, click

Refresh to update this screen. Click Next.

7 Enter the default password (1234) and click OK.

8 Replace the unique generated device name with a more

friendly recognizable name with additional descriptive text

if you want. Alternatively, leave the fields at the default

settings. Click Next.

8

ENGLISH

9 If the NPS-520 is connected to a network that has a DHCP

server, select DHCP to have the DHCP server assign

TCP/IP information (such as IP address and subnet mask)

to your NPS-520. Otherwise, select Manual IP and enter

an IP address (in the same subnet as your network),

subnet mask and the gateway’s IP address. Click Next.

" We recommend you give the NPS-520 a static

IP address or configure your DHCP server to

always give it the same IP address (static

DHCP). If the NPS-520’s IP address changes,

you need to uninstall and reinstall the ZyXEL

utility on each computer that uses it.

ENGLISH

9

If you selected DHCP in the previous screen but there was

no DHCP server found in your network, the following screen

displays. Click Yes to go back to the TCP/IP configuration

screen or click No to have the NPS-520 search for the DHCP

server again.

If your computer and the NPS-520 are not in the same

subnet, the following screen pops up. Click OK (or Yes) to

continue.

10This read-only screen shows the current settings. Check

whether what you have configured is correct and click

10

ENGLISH

Finish. Otherwise, click Back to re-configure the

information.

11Click Finish to complete the installation.

12Repeat these steps on each Windows computer in your

network that will use the NPS-520.

ENGLISH

11

2.2 Using the Utility on Windows

If you already installed a printer driver, you still need to

associate it with the NPS-520.

2.2.1 Printer Driver Installation and Association

1 Start the ZyXEL utility by either double-clicking the utility

icon in the system tray or clicking Start > (All) Programs >

ZyXEL NPS-520 Utility > NPS-520 Utility.

2 The Status screen displays. Select the name of your NPS-

520 and click Connect.

3 Windows automatically detects the printer and prompts

you to install the printer driver. Follow the on-screen

12

ENGLISH

instructions to install a new driver and/or have the driver

associate with the NPS-520.

2.2.2 Managing the NPS-520

To have computers in the network take turns to use the

printer, you need to enable Auto Connect in the utility Status

screen and select a default printer. Auto connect allows the

NPS-520 to communicate with the printer when you want to

use it. The NPS-520 drops the connection after the job is

finished.

Alternatively, click Connect and set the Auto Release idle

timeout.

ENGLISH

13

" If you disable Auto Release, only that computer

can use the printer. Click Disconnect to

manually drop the connection.

" The Auto Release and Auto Connect features

are not configurable if your computer operating

system version is older then Windows 2000

SP4.

14

ENGLISH

" If the printer is not connected or not available

when you send out a request, the request will be

put in your computer’s print queue until the

printer is available.

V If you cannot use the printer, make sure you

enable Auto Release and/or Auto Connect on

all Windows computers.

3 Web Configurator

Follow the steps below to use the web configurator to

configure the NPS-520’s TCP/IP settings. See your User’s

Guide for more information and how to add a printer on your

computer.

Use Internet Explorer 6.0 and later or Netscape Navigator 7.0

and later versions.

1 Open your web browser.

2 Type the NPS-520’s default IP address (192.168.1.6) as

the URL.

ENGLISH

15

3 Type “1234” (default) as the password and click Login.

V If the login screen does not display, make sure

your computer is in the same subnet as the

NPS-520.

You may also need to check your browser’s

security settings and make sure your

computer’s Ethernet card is installed and

functioning properly.

4 Click Setup TCP/IP to configure the NPS-520’s IP

address.

If the NPS-520 is connected to a network that has a DHCP

server, select Obtain IP automatically to have the DHCP

server assign TCP/IP information (such as IP address and

subnet mask) to your NPS-520. Otherwise, select Use Fixed

IP Address and enter an IP address (in the same subnet as

your network), subnet mask and the gateway’s IP address.

16

ENGLISH

" We recommend you give the NPS-520 a static

IP address or configure your DHCP server to

always give it the same IP address (static

DHCP). If the NPS-520’s IP address changes,

you need to uninstall and reinstall the ZyXEL

utility on each computer that uses it.

Click Apply to save your changes.

4 System Requirements

Before installation, make sure you have a computer with the

following:

• Pentium II 300 MHz or above

• A minimum of 20 MB available hard disk space

ENGLISH

17

• A minimum of 32 MB RAM

• A CD-ROM drive

• Windows 98 Second Edition (SE), Windows Me, Windows

2000, Windows 2003, Windows XP, Unix/Linux (with LPR/

LPD protocol support), Mac OS 9.x or later

• Windows 98 SE users may need the Windows 98 SE CD

Procedure to View a Product's

Certification(s)

1 Go to www.zyxel.com.

2 Select your product from the drop-down list box on the

ZyXEL home page to go to that product's page.

3 Select the certification you wish to view from this page.

18

ENGLISH

DEUTSCH

19

Übersicht

Der NPS-520 ist ein Druckserver mit einem Ethernet- und

einem USB-Anschluss (v2.0). Am USB-Anschluss des NPS-

520 (in der folgenden Abbildung als NPS bezeichnet) kann ein

Drucker angeschlossen werden, welcher dann von allen

Computern des Netzwerkes verwendet werden kann.

Über den NPS-520 arbeitet der Drucker, als wäre er direkt an

dem Computer angeschlossen.

" Der Treiber (und wenn vorhanden das Utility-

Programm) des Druckers (der an dem NPS-520

angeschlossen ist) muss auf dem Computer

installiert sein. Weitere Informationen finden Sie

im Benutzerhandbuch des Druckers.

In dieser Anleitung wird beschrieben,

1 wie die Hardware installiert wird und

DEUTSCH

La page charge ...

ZyXEL Printer NPS-520 Manuel utilisateur

Ce manuel convient également à

ZyXEL Printer NPS-520 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents