Topdon VS2000Plus Manuel utilisateur

Jump Starter & Battery Tester USER MANUAL

VS2000Plus

CONTENTS

Safety Is Always the First

Priority!

DE

21

22

23

26

29

32

33

EN

5

6

7

10

13

16

FR

35

36

37

40

43

46

IT

77

78

79

82

85

88

60

63

64

65

68

71

74

PT

49

50

52

54

57

60

88

ES

Section 1 About VS2000Plus

Section 2 What's in the

Box?

Section 7 Specications

Section 8 Warranty

Section 3 Product Overview

Section 4 Recharge the

Jump Starter

Section 5 How to Jump

Start a 12V Battery Vehicle?

Section 6 How to Perform a

Battery Test?

4

ENGLISH

5

SAFETY IS ALWAYS THE FIRST

PRIORITY!

READ ALL INSTRUCTIONS BEFORE USE

For your safety, the safety of others, and to avoid any

damage to the product and your vehicle, CAREFULLY READ

AND MAKE SURE YOU FULLY UNDERSTAND ALL THE

SAFETY INSTRUCTIONS AND MESSAGES ON THIS MANUAL

BEFORE OPERATING.

ALWAYS WEAR APPROVED SAFETY GOGGLES while

working near a battery.

ONLY use the battery clamps that come with this product.

DO NOT use this product if the cable or the jump starter

has any damage.

DO NOT put the product under direct sunlight or in high

temperature areas.

DO NOT disassemble the product.

DO NOT SMOKE OR HAVE ANY FLAMES NEAR THE

VEHICLE when testing. The fuel and battery vapors are

highly ammable.

WARNING: Battery acid is extremely corrosive. If acid gets

into your eyes, FLUSH THEM THOROUGHLY WITH COLD

RUNNING WATER FOR AT LEAST 20 MINUTES AND SEEK

MEDICAL ATTENTION IMMEDIATELY.

If battery acid gets on your skin or clothing, WASH IT

IMMEDIATELY WITH A SOLUTION OF WATER AND BAKING

SODA.

6

SECTION 1 ABOUT VS2000PLUS

The VS2000Plus is a two-in-one tool that combines

jump-starting and battery testing functions. It provides

a perfect solution for vehicle jump-starting, battery

testing, power supply, emergency illumination and

other scenarios.

SECTION 2 WHAT'S IN THE BOX?

VS2000Plus Jump Starter

Smart Battery Clamps (Wireless Battery Tester)

USB Cable (Type-A to Type-C)

User Manual

Carrying Case

7

SECTION 3 PRODUCT OVERVIEW

Jump Starter

2

1

3

5 7

6 8

4

8

Power Button

Short press to power ON; long press to turn on the LED

light, then short press to toggle the LED light among

the following modes: Flashlight, SOS, Strobe and OFF.

Battery Level Indicators

Indicate the charge level of the internal battery.

Note: Only jump start vehicles when the battery level of

the jump starter is above 50%.

LED Light

Jump Start Socket

USB Output (QC3.0 12V/1.5A, 9V/2A, 5V/3A)

DC Output (Max 16.8V/10A)

Type-C Input/Output (PD60W 20V/3A, 15V/3A, 12V/3A,

9V/3A, 5V/3A)

1.

2.

3.

4.

5.

6.

7.

8.

9

Smart Battery Clamps (Wireless Battery Tester)

1 2 3

OK/Err Indicator

OK：Solid green

The jumper starter is ready for use.

Err：Solid / ashing red

Illuminates or ashes red if reverse polarity, short circuit

or over temperature is detected.

Bluetooth Connection Indicator

Solid blue

Bluetooth connected

Flashing blue

Bluetooth not connected

BOOST Button

Short press to enable BOOST mode (forced output

mode). The status indicator will light up green. Start

your vehicle within 30 seconds. The BOOST mode will

be automatically turned off if no operation is performed

within 30 seconds or after the vehicle is successfully

cranked, and the green LED light will be off.

Note: Under BOOST mode, all safety protections are

disabled temporarily. Therefore, only use this mode

when the vehicle battery voltage is extremely low.

1.

2.

3.

10

SECTION 4 RECHARGE THE JUMP

STARTER

The jump starter comes partially charged and needs to

be fully charged prior to use. Please charge it through the

Type-C input port once you receive it.

SECTION 5 HOW TO JUMP START A

12V BATTERY VEHICLE?

IMPORTANT

Make sure you have turned off all of the power loads of the

vehicle, including headlights, radio, air conditioner, etc., before

attempting to jump start the vehicle.

Note:

The jump-starting function is only applicable to 12V battery

vehicles.

Step 1:

11

Step 2:

Connect the battery clamps to the vehicle battery. Red

clamp to the positive polarity (+), black clamp to the

negative polarity (-). The status indicator will illuminate

green, which indicates it is ready for jump starting. Just by

clamping the terminals correctly, the VS2000Plus delivers a

jump to the battery.

Plug the blue end of the smart battery clamps into the jump

start socket.

12

Note:

• The jump starter has a built-in buzzer that will ring when

reverse polarity, over temperature, short circuit, or other

improper connections are detected. Disconnect the clamps

from the battery if the buzzer rings and connect them again

after the issue is resolved.

• If the status indicator doesn't turn on, press the BOOST

Button to enable the forced output mode.

Step 3:

Try starting the vehicle. If it fails, disconnect the clamps from

the vehicle's battery and wait for 20 seconds, then reconnect

and try again. Do not attempt more than 3 consecutive jump

starts within 2 minutes.

Step 4:

After successfully jumpstarting the vehicle, remove the

clamps from vehicle battery and separate the clamps and

jump starter. Your jump starter will automatically power off

after a few seconds.

13

SECTION 6 HOW TO PERFORM A

BATTERY TEST?

Getting Started

Download and install the app

Option 1 Scan QR code

For both iOS and Android, you can open the camera on

your phone and scan the QR code below to download

the app.

1.

14

Note:

For battery testing functions, there is no need to connect the

VS2000Plus jump starter, only the clamps.

Note:

Please ensure that you have enabled the "Scan QR

Codes" feature for your phone's camera in Settings.

Option 2 Go to App Store / Google Play

For iOS: Search for "BatteryLab" in App Store to download

the app.

For Android: Search for "JumpSurge" in Google Play to

download the app.

Connect the battery clamps to the vehicle battery. Red

clamp to the positive polarity (+), black clamp to the

negative polarity (-). The Bluetooth connection indicator

will ash blue.

2.

15

Connect the smart battery clamps (battery tester) to

your phone via Bluetooth

Open the BatteryLab/JumpSurge app and tap the

Bluetooth icon to establish connection with the unit.

3.

Perform Battery Tests

The BatteryLab/JumpSurge app provides detailed

instructions on how to test a battery. Thus, to perform a

battery / cranking / charging test, simply follow the on-screen

instructions.

Note:

The battery testing function is only applicable to 12V lead-acid

batteries.

16

TOPDON One Year Limited Warranty

TOPDON warrants to its original purchaser that the

company's products will be free from defects in material

and workmanship for 12 months from the date of purchase

(Warranty Period).

For the defects reported during the Warranty Period,

TOPDON will either repair or replace the defective part or

product according to its technical support analysis and

conrmation.

TOPDON shall not be liable for any incidental or consequential

damages arising from the device's use, misuse, or mounting.

If there is any conict between the TOPDON warranty policy

and local laws, the local laws shall prevail.

SECTION 7 SPECIFICATIONS

SECTION 8 WARRANTY

59.2Wh/16000mAh, 3.7V

QC18W 12V 1.5A, 9V 2A, 5V 3A

Max 16.8V 10A

PD60W 20V 3A, 15V 3A, 12V 3A,

9V 3A, 5V 3A

2000A

-10℃ to 40℃ (14 ℉ to 104 ℉)

-20℃ to 75℃ (-4 ℉ to 167 ℉)

BatteryCapacity

USB1 Output

USB2 Output

DC Output

Type-C Input/Output

Peak Current

WorkingTemperature

StorageTemperature

17

Note:

All information in this manual is based on the latest

information available at the time of publication and no

warranty can be made for its accuracy or completeness.

TOPDON reserves the right to make changes at any time

without notice.

This limited warranty is void under the following conditions:

• Misused, disassembled, altered or repaired by unauthorized

stores or technicians.

• Careless handling and/or improper operation.

18

Any changes or modications not expressly approved by

the party responsible for compliance could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses,

and can radiate radio frequency energy, and if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause

harmful interference to radio or television reception, which

can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver.

- Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician

for help.

SECTION 9 FCC

19

20

DEUTSCH

La page est en cours de chargement...

Topdon VS2000Plus Manuel utilisateur

Topdon VS2000Plus Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents