Sun Joe 24V-PS8-LTE Manuel utilisateur

Marque: Sun Joe

Modèle: 24V-PS8-LTE

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

A Division of Snow Joe®, LLC Model 24V-PS8-LTE Form No. SJ-24V-PS8-LTE-880E-MR4

OPERATOR’S MANUAL

CORDLESS POLE CHAIN SAW

24V MAX* | 2.0 Ah | 8-INCH | MULTI-ANGLE

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in serious bodily injury or death.

General Safety

mWARNING! This appliance is not intended for use

by children or by unassisted, unsupervised persons whose

physical, sensory or mental capabilities prevent them from

using it safely. Children should be supervised to ensure that

they do not play with the appliance.

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

mWARNING! When using the power tool, basic safety

precautions should always be followed to reduce the risk of

re, electric shock, and personal injury. These include:

1. Keep work area clean and well-lit – Cluttered, dark

areas invite accidents.

2. Avoid dangerous environments – Do not use the power

tool in rain, in damp or wet locations, or in bad weather,

especially when there is a risk of lighting. This decreases

the risk of being struck by lighting. Do not operate the

power tool in gaseous or explosive atmospheres or use

the power tool near ammable or combustible liquids.

Motors in these tools normally spark, and the sparks

might ignite fumes.

3. Know your product – Know how to start and stop the

machine. Be thoroughly familiar with the controls.

4. Keep children, bystanders, and pets away –

All spectators, including pets, should be kept a safe

distance away from the work area.

5. Dress properly – Do not wear loose clothing or jewelry.

They can get caught in moving parts. Protective rubber

gloves and non-slip footwear are recommended when

working outdoors.

6. mCAUTION! – Exercise caution to avoid slipping or

falling. Wear protective footwear that will protect your feet

and improve your footing on slippery surfaces.

7. Stay alert – Watch what you are doing. Use common

sense. Do not operate the power tool when you are tired,

or under the inuence of alcohol or drugs.

8. Do not overreach – Keep proper footing and balance at

all times.

9. Prevent unintentional starting – Ensure the switch is in

the o-position before connecting to battery pack, picking

up or carrying the appliance. Carrying the appliance with

your nger on the switch or energizing appliance that have

the switch on invites accidents.

NOTE: This warning is not applicable for batteries that

cannot be disconnected from the appliance in normal use.

10.

Use the right appliance – Do not use the power tool for

any applications other than those for which it was intended.

11. Blades are sharp – Don't grasp the exposed cutting

blades or cutting edges when picking up or holding the

power tool.

12. Use two hands – Hold the telescoping pole and handle

with both hands to avoid loss of control.

13. Remove the battery – Remove the battery from the

power tool when it is not in use, before servicing it, when

changing accessories, and when performing any other

maintenance task.

14.

Use safety glasses – Also use safety footwear, snug-tting

clothing, protective gloves, hearing and head protection.

15. Use head protection – Always use head protection when

operating the power tool overhead. Falling debris can

result in serious personal injury.

16. Do not force the tool – It will perform better with less

likelihood of personal or mechanical injury if it is used at

the rate for which it was designed.

17. Store indoors – When not in use, the power tool should

be stored indoors in a dry and high or locked-up place out

of the reach of children.

18. Check for damaged parts – Before further use of the

appliance, all guards and parts should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other condition that may aect its

operation. A guard or other part that is damaged should

be properly repaired or replaced. Contact the Snow Joe®

+ Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563) for assistance.

19. Maintain the power tool with care – Keep the cutting

edges sharp and clean for optimal performance and to

reduce the risk of injury. Keep the handles dry, clean,

and free from oil and grease. Follow the additional

recommendations described in the maintenance section

of this manual.

20. Do not use the power tool if the switch does not turn it on

and o. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

21. Keep all parts of the body away from the cutting blades or

chain. Do not remove cut material or hold material to be cut

when blades are moving. Make sure the switch is o when

clearing jammed material. The blades or chain will continue

moving for a while after the tool is turned o. A moment

of inattention while operating the power tool may result in

serious personal injury.

22. Carry the power tool by the handle with the cutting blade

or chain stopped. When transporting or storing the power

tool, always keep the blades or chain bar covered.

Proper handling of the pole chain saw will reduce possible

personal injury from the cutting blades or chain.

23. Hold the product by insulated gripping surfaces only,

because the cutting blade or chain may contact hidden

wiring. Cutting blades or chain contacting a “live” wire

may make exposed metal parts of the product “live” and

could give the operator an electric shock.

24. The unit has not been designed to provide protection

from electric shock in the event of contact with overhead

electric lines. Never use the power tool near any electrical

power lines. Contact with or use near power lines may

cause serious injury or electric shock resulting in death.

Maintain a minimum clearance of 50 ft (15 m) from all

power lines.

mWARNING! Before inspecting, cleaning, or servicing

the machine, remove the battery and wait for all moving

parts to stop. Failure to follow these instructions can result in

serious personal injury or property damage.

mWARNING! Do not use this appliance without reading

this instruction manual.

mWARNING! Do not use the appliance within range of

persons unless they are wearing protective clothing.

mWARNING! Do not operate the cordless power tool in

a tree, on a ladder, or on a scaold. Using the tool under such

circumstances is extremely dangerous.

mWARNING! Do not let familiarity with this type of tool

prevent you from taking all necessary precautions. Remember

that a careless fraction of a second is sucient to inict

serious injury.

mWARNING! The cordless pole chain saw must be fully

assembled before operation! Do not use the tool that is only

partly assembled or assembled with damaged parts!

mWARNING! Starting, stopping, and restarting an

electric motor repeatedly within a few seconds can generate

a great deal of heat and damage the motor. To protect the life

of your cordless power tool, always wait at least ve seconds

after stopping before restarting the unit.

mWARNING! Electrical Shock Hazard – Before starting

up your machine, please check it carefully for any defects.

If you nd any, do not start up your machine and contact your

distributor.

NOTE: Take care of small parts that are removed during

assembly or when making adjustments. Keep them secure to

avoid loss.

Please contact an authorized Snow Joe® + Sun Joe® dealer

or call the Snow Joe® + Sun Joe® customer service center

at 1-866-SNOWJOE (1-866-766-9563) for all maintenance

or operations not foreseen in this manual. Any operation

performed in an unauthorized service center or by unqualied

personnel will completely invalidate the warranty.

mWARNING! For your safety and that of others:

• Correct maintenance is essential to maintain the original

eciency and safety of the machine over time.

• Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

• Never use the machine with worn or damaged parts.

Damaged parts are to be replaced and never repaired.

mWARNING! Always wear protective gloves during

maintenance operations.

mWARNING! Use only original manufacturer’s

replacement parts, accessories and attachments. Failure to do

so can cause possible injury and poor performance.

To order genuine replacement parts or accessories for the

Sun Joe® iON+ cordless pole chain saw, please visit sunjoe.

com or contact the Snow Joe® + Sun Joe® customer service

center at 1-866-SNOWJOE (1-866-766-9563).

Cleaning the Tool

mWARNING! Never let any liquid get inside the motor

housing and NEVER immerse any part of the housing in liquid.

1. Stop the motor and remove the battery.

2. Clean dirt and debris from the body of the tool, using a

damp cloth with a mild detergent.

NOTE: Do not use any strong detergents on the plastic

housing or the handle, as they can be damaged by certain

aromatic oils such as pine and lemon, and by solvents

such as kerosene.

Storage

mWARNING! Do not at any time let brake uids, gasoline,

petroleum-based products, penetrating oils, etc., come in

contact with plastic parts. Chemicals can damage, weaken, or

destroy plastic which may result in serious personal injury.

1. Stop the motor and remove the battery.

2. Clean the pole chain saw thoroughly before storing.

3. Always place the bar sheath on the chain bar before

storing or transporting the pole chain saw. Use caution to

avoid the sharp teeth of the blade and the chain.

4. Store the pole chain saw indoors, in a dry place that is

inaccessible to children. Keep away from corrosive agents

such as garden chemicals and de-icing salts.

5. We recommend using the original package for storage or

covering the product with a suitable cloth or enclosure to

protect it against dust.

Specic Safety Warnings

for Pole Chain Saw

1. Only the pole chain saw operator should be in the

work area.

2. Do not use the pole chain saw to cut down trees.

3. Always use two hands when operating the pole chain saw.

Grip the pole chain saw securely with one hand on the

trigger and the other hand on the pole.

4. Before starting the pole chain saw, make sure that the saw

chain is not in contact with any object.

5. Do not allow the pole chain saw to make contact with

grounded objects such as pipes, fences, and metal posts.

6. Do not force the pole chain saw while cutting. Apply light

pressure. It will perform more eectively and safely if it is

used at the rate for which it was designed.

7. Use extreme caution when cutting a limb that is under

tension. When wood tension is released, the limb could

spring back and strike the operator, causing severe injury

or death.

8. During transport, hold the pole at its balance point,

with the guide bar and chain facing to the rear.

9. Do not cut small brush and saplings with the pole chain

saw. Small branches may catch in the chain and be

whipped towards the operator, which could pull the

operator o balance.

10. Never stand directly under the limb you are trimming.

Always position yourself outside the path of falling debris.

11. Keep a rm, steady pressure on the pole chain saw while

cutting. Do not try to cut limbs larger in diameter than the

length of the guide bar.

12. Keep other people and pets away from the cutting end of

the pole chain saw and at a safe distance away from the

work area.

Kickback

mWARNING! Kickback may occur when the nose or tip

of the guide bar touches an object, or when the wood closes in

and pinches the saw chain in the cut.

AVOID CONTACTING THE GUIDE BAR TIP WITH ANY

OBJECT. In some cases, when the tip makes contact with an

object, it may cause a fast reverse reaction, kicking the guide

bar up and back towards the operator. Pinching the saw chain

along the top of the guide bar may also push the guide bar

rapidly back towards the operator. Either of these reactions

may cause you to lose control of the pole chain saw, which

could result in serious personal injury. Follow the necessary

precautions indicated below to avoid kickbacks.

• Always use two hands when operating the pole chain saw,

one hand gripping the trigger and the other hand gripping

the pole. Use a rm grip. Thumbs and ngers must wrap

around the trigger and the pole.

• Keep all guards in place on the pole chain saw. Make sure

they are in proper working order.

• Do not overreach or extend arms above shoulder height.

• Keep solid footing and balance at all times.

• Never try cutting through two branches at the same time.

Only cut one at a time.

• Do not bury the guide bar nose or try to cut by boring the

guide bar nose into the wood.

• Watch for shifting of wood or other forces that may pinch

the chain.

• Use extreme caution when re-entering a previous cut.

• Use the low-kickback chain and guide bar supplied with

this pole chain saw. Only use genuine Snow Joe® +

Sun Joe® replacement parts designed specically for use

with this pole chain saw.

• Never use a dull or loose chain. Keep the chain sharp and

properly tensioned.

Battery & Charger

Safety Instructions

We pay a great deal of attention to the design of every battery

pack to ensure that we supply you with batteries that are safe,

durable and have a high energy density. The battery cells have

a wide range of safety devices. Each individual cell is initially

formatted and its electrical characteristic curves are recorded.

This data is then used exclusively to be able to assemble the

best possible battery packs.

Despite all the safety precautions, caution must always be

exercised when handling batteries. The following points must

be obeyed at all times to ensure safe use. Safe use can only

be guaranteed if undamaged cells are used. Incorrect handling

of the battery pack can cause cell damage.

IMPORTANT! Analyses conrm that incorrect use and poor

care of high-performance batteries are the main factors

responsible for personal and/or product damage.

mWARNING! Use only approved replacement batteries;

other batteries may damage the power tool and cause it to

malfunction, which can lead to serious personal injury.

mWARNING!

Do not use a battery pack or appliance that is

damaged or modied. Damaged or modied batteries may exhibit

unpredictable behavior resulting in re, explosion or risk of injury.

Do not modify or attempt to repair the appliance or the battery

pack except as indicated in the instructions for use and care.

Have your battery pack serviced by a qualied repair person

using only identical replacement parts. This will ensure that the

safety of the battery pack is maintained.

mCAUTION! To reduce the risk of injury, charge the

iON+ 24V lithium-ion battery pack only in its designated

iON+ 24V lithium-ion charger. Other types of chargers present

risk of re, personal injury and damage. Do not wire a battery

pack to a power supply plug or car cigarette lighter. Such

misuse will permanently disable or damage the battery pack.

• Avoid dangerous environments – Do not charge the

battery pack in rain, snow or in damp or wet locations.

Do not use the battery pack or charger in the presence of

explosive atmospheres (gaseous fumes, dust or ammable

materials) because sparks may be generated when inserting

or removing the battery pack, which could lead to a re.

• Charge in a well-ventilated area – Do not block the

charger vents. Keep them clear to allow for proper

ventilation. Do not allow smoking or open ames near a

charging battery pack. Vented gases may explode.

NOTE: The safe temperature range for the battery is

41°F – 105ºF (5°C – 40.5°C). Do not charge the battery

outside in freezing weather; charge it at room temperature.

• Maintain charger cord – When unplugging the charger, pull

the plug, not the cord, from the receptacle to reduce the

risk of damage to the electrical plug and cord. Never carry

the charger by its cord or yank it by the cord to disconnect

it from the receptacle. Keep the cord away from heat, oil

and sharp edges. Make sure the cord will not be stepped

on, tripped over or subjected to damage or stress when the

charger is in use. Do not use the charger with a damaged

cord or plug. Replace a damaged charger immediately.

• Do not use an extension cord unless it is absolutely

necessary – Using the wrong, damaged or improperly

wired extension cord poses a risk of re and electric shock.

If an extension cord must be used, plug the charger into a

properly wired 16 gauge or larger extension cord with the

female plug matching the male plug on the charger. Make

sure that the extension cord is in good electrical condition.

• Charger 24VCHRG-AC is rated for 100 – 240 volt AC

only – The charger must be plugged into an appropriate

receptacle.

• Use only recommended attachments – Use of an

attachment not recommended or sold by the battery

charger or battery pack manufacturer may result in risk of

re, electric shock or personal injury.

• Unplug charger when not in use – Make sure to remove

battery packs from unplugged chargers.

mWARNING! To reduce the risk of electric shock,

always unplug the charger before performing any cleaning

or maintenance. Do not allow water to ow into the charger.

Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock

hazards.

• Do not burn or incinerate battery packs – Battery packs

may explode, causing personal injury or damage.

Toxic fumes and materials are created when battery packs

are burned.

• Do not crush, drop or damage battery packs – Do not

use the battery pack or charger if they have sustained a

sharp blow, been dropped, run over or have been damaged

in any way (i.e. pierced with a nail, hit with a hammer,

stepped on, etc.).

• Do not disassemble – Incorrect reassembly may pose

a serious risk of electric shock, re or exposure to toxic

battery chemicals. If the battery or charger are damaged,

contact an authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563) for assistance.

• Battery chemicals cause serious burns – Never let a

damaged battery pack contact the skin, eyes or mouth. If a

damaged battery pack leaks battery chemicals, use rubber

or neoprene gloves to safely dispose of it. If skin is exposed

to battery uids, wash the aected area with soap and

water and rinse with vinegar. If eyes are exposed to battery

chemicals, immediately ush with water for

20 minutes and seek medical attention. Remove and

dispose of contaminated clothing.

• Do not short circuit – When battery pack is not in use,

keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects,

that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns or

a re.

• Store your battery pack and charger in a cool, dry

place – Do not store the battery pack or charger where

temperatures may exceed 105ºF (40.5ºC), such as in direct

sunlight or inside a vehicle or metal building during the

summer.

Information about the battery

1. The battery pack supplied with your cordless power tool is

only partially charged. The battery pack has to be charged

completely before you use the tool for the rst time.

2. For optimum battery performance, avoid low discharge

cycles by charging the battery pack frequently.

3. Store the battery pack in a cool place, ideally at 77°F

(25°C) and charged to at least 40%.

4. Lithium-ion batteries are subject to a natural aging

process. The battery pack must be replaced at the latest

when its capacity falls to just 80% of its capacity when

new. Weakened cells in an aged battery pack are no

longer capable of meeting the high power requirements

needed for the proper operation of your cordless pole

chain saw, and therefore pose a safety risk.

5. Do not throw battery packs into an open re as this poses

a risk of explosion.

6. Do not ignite the battery pack or expose it to re.

7. Do not exhaustively discharge batteries. Exhaustive

discharge will damage the battery cells. The most

common cause of exhaustive discharge is lengthy storage

or non-use of partially discharged batteries. Stop working

as soon as the performance of the battery falls noticeably

or the electronic protection system triggers. Place the

battery pack in storage only after it has been fully charged.

8. Protect batteries and the tool from overloads. Overloads

will quickly result in overheating and cell damage inside

the battery housing even if this overheating is not apparent

externally.

Avoid damage and shocks. Immediately replace batteries

that have been dropped from a height of more than 3 feet

(1 meter) or those that have been exposed to violent shocks,

even if the housing of the battery pack appears to be

undamaged. The battery cells inside the battery may have

suered serious damage. In such instances, please read the

waste disposal information for proper battery disposal.

10. If the battery pack suers overloading and overheating,

the integrated protective cuto will switch o the

equipment for safety reasons.

IMPORTANT! Do not press the ON/OFF trigger switch any

more if the protective cut-o has been activated. This may

damage the battery pack.

11. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with

another battery pack.

12. Use appliances only with specically designated battery

packs. Use of any other battery packs may create a risk of

injury and re.

13. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

14. Do not use a battery pack or appliance that is damaged

or modied. Damaged or modied batteries may exhibit

unpredictable behavior resulting in re, explosion or risk of

injury.

15. Do not expose a battery pack or appliance to re or

excessive temperature. Exposure to re or temperature

above 266ºF (130°C) may cause explosion.

16. Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature

range specied in the instructions. Charging improperly

or at temperatures outside of the specied range may

damage the battery and increase the risk of re.

Information about the charger and the

charging process

1. Please check the data marked on the rating plate of the

battery charger. Be sure to connect the battery charger

to a power supply with the voltage marked on the rating

plate. Never connect it to a dierent mains voltage.

2. Protect the battery charger and its cord from damage.

Keep the charger and its cord away from heat, oil and

sharp edges. Have damaged cords repaired without delay

by a qualied technician at an authorized Snow Joe® +

Sun Joe® dealer or call the Snow Joe® + Sun Joe®

customer service center at 1-866-SNOWJOE

(1-866-766-9563).

3. Electrical plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

grounded appliances. Unmodied plugs and matching

outlets will reduce the risk of electric shock.

4. Keep the battery charger, battery pack(s) and the cordless

tool out of the reach of children.

5. Do not use the supplied battery charger to charge other

cordless tools.

6. During periods of heavy use, the battery pack will become

warm. Allow the battery pack to cool to room temperature

before inserting it into the charger to recharge.

7. Do not overcharge batteries. Do not exceed the maximum

charging times. These charging times only apply to

discharged batteries. Frequent insertion of a charged or

partially charged battery pack will result in overcharging

and cell damage. Do not leave batteries in the charger for

days on end.

Never use or charge batteries if you suspect that it has been

more than 12 months since the last time they were charged.

There is a high probability that the battery pack has already

suered dangerous damage (exhaustive discharge).

9. Charging batteries at a temperature below 41°F (5°C) will

cause chemical damage to the cells and may cause a re.

10. Do not use batteries that have been exposed to heat

during the charging process, as the battery cells may have

suered dangerous damage.

11. Do not use batteries that have suered curvature or

deformation during the charging process or those that

exhibit other atypical symptoms (gassing, hissing,

cracking, etc.).

12. Never fully discharge the battery pack (maximum

recommended depth of discharge is 80%). A complete

discharge of the battery pack will lead to premature aging

of the battery cells.

Protection from environmental inuences

1. Wear suitable work clothes. Wear safety goggles.

2. Protect your cordless tool and the battery charger from

moisture and rain. Moisture and rain can cause dangerous

cell damage.

3. Do not use the cordless tool or the battery charger near

vapors and ammable liquids.

4. Use the battery charger and cordless tools only in dry

conditions and at an ambient temperature of 41ºF – 105°F

(5°C – 40.5°C).

5. Do not keep the battery charger in places where the

temperature is liable to reach over 105°F (40.5°C). In

particular, do not leave the battery charger in a car that is

parked in the sunshine.

6. Protect batteries from overheating. Overloads,

overcharging and exposure to direct sunlight will result

in overheating and cell damage. Never charge or work

with batteries that have been overheated – replace them

immediately, if possible.

7. Store the charger and your cordless tool only in dry

locations with an ambient temperature of 41ºF – 105°F

(5°C – 40.5°C). Store your lithium-ion battery pack in a

cool, dry place at a temperature of 77°F (25°C). Protect

the battery pack, charger and cordless tool from humidity

and direct sunlight. Only place fully charged batteries in

storage (charged to at least 40%).

8. Prevent the lithium-ion battery pack from freezing. Battery

packs that were stored below 32°F (0°C) for more than

60 minutes must be discarded.

9. When handling batteries, be wary of electrostatic charge.

Electrostatic discharges can damage the electronic

protection system and the battery cells. Avoid electrostatic

charging and never touch the battery poles.

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

READ THE OPERATOR'S

MANUAL(S) – Read, understand,

and follow all instructions in the

user manual(s) before attempting

to assemble and operate.

SAFETY ALERT – Indicates a

precaution, a warning, or a danger.

WEAR EYE AND HEARING

PROTECTION – For protection

against injury, wear ear defenders

and safety goggles.

WARNING! Do not expose the unit

to rain or wet conditions. Keep dry.

Symbols SymbolsDescriptions Descriptions

Indoor use only. Only use battery

charger indoors.

50 ft

(15 m) WARNING! SHOCK HAZARD –

Keep at least 50 ft (15 m) away

from power lines. Do not overreach.

Keep proper footing and balance at

all times.

DANGER! ROTATING BLADES

– Keep hands and feet away from

openings while the saw is running.

Thrown objects and rotating

blade can cause severe

injury.

Keep bystanders a minimum

distance of 50 ft (15 m) away from

the work area.

Wear protective gloves and non-slip

footwear when using the machine

and handling debris.

Know Your Cordless Pole Chain Saw

Read the owner’s manual and safety instructions carefully before operating the cordless pole chain saw. Compare the illustration

below to the cordless pole chain saw in order to familiarize yourself with the location of the various controls and adjustments.

Save this manual for future reference.

*Initial no-load voltage, when fully charged, peaks at 24 volts; nominal voltage under typical load is 21.6 volts.

1. Cutting bar sheath

2. Oil tank cap

3. Chain saw head

4. Multi-angle head adjustment dial

5. Lock tab

6. Telescoping pole

7. Auxiliary handle

8. Soft grip

9. Rear handle

10. Safety lock switch

11. Trigger switch

12. Battery compartment

13. Auxiliary handle loop

14. Auxiliary handle lock knob

15. Telescoping lock

16. Assembly lock

17. Chain/sprocket end cover

18. Chain/sprocket end cover knob

19. Chain tensioner ring

20. 8 in. (20.3 cm) chain

21. 8 in. (20.3 cm) guide bar

22. Oil level indicator window

23. Battery indicators

24. Push button for battery indicator

25. Charge socket

26. 24V iON+ lithium-ion battery charger

(24VCHRG-AC)

27. Charger plug

28. 24V iON+ lithium-ion battery

(24VBAT-LTE) featuring exclusive

EcoSharp® technology

29. Push lock button

Technical Data

Motor ................................................................................ 350 W

Battery Voltage Max* .................................................... 24V D.C.

Battery Capacity ............................................................... 2.0 Ah

Charger Input .................................................... 100 – 240V AC,

50 – 60 Hz, 50 W

Charger Output .................................. 25.2 V DC, 1400 mA

Charge Time Max ......................................................1 hr 20 min

No Load Speed ........................................................... 2800 rpm

Bar Chain Length .................................................8 in. (20.3 cm)

Cutting Thickness Max ........................................7.5 in. (19 cm)

Recommended: 6.5 in. (16.5 cm)

Multi-Angle Head ......................................................... 0º to 30º

Telescopic Pole ..................................................... 3.7 ft to 7.2 ft

(1.1 m to 2.2 m)

Auxiliary Handle Angles ......................................... -45° | 0° | 45°

Overhead Reach ............................................ Up to 14 ft (4.3 m)

Oil Tank Capacity ............................................... 2.7  oz (80 ml)

Net Weight ............................................................. 7.7 lbs (3.5 kg)

Back of the chain saw head

27 28 29

2425

678910 2

20191817161512 141311

Unpacking

Carton Contents

• Telescoping pole with auxiliary handle

• Chain saw head with chain and bar pre-mounted

• Chain saw bar sheath

• 24V iON+ lithium-ion battery

• 24V iON+ lithium-ion battery charger

• Hex key wrench

• Manual with registration card

1. Carefully remove the cordless pole chain saw and check

to see that all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you nd damaged or

missing parts, DO NOT return the unit to the store. Please

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging

material until you are ready to use your new cordless pole

chain saw. The packaging is made of recyclable materials.

Properly dispose of these materials in accordance with

local regulations.

IMPORTANT! The equipment and packaging material are

not toys. Do not let children play with plastic bags, foils,

or small parts. These items can be swallowed and pose a

suocation risk!

Battery Pack Operation

The equipment is powered by a lithium-ion battery. The battery

pack is completely sealed and maintenance free.

Battery Charge Level Indicator

The battery pack is equipped with a push button for checking

the charge level. Simply press the push button to read o the

battery charge level from the LEDs of the battery indicator:

• All 3 level monitoring LEDs are lit: Battery charge level

is high.

• 2 level monitoring LEDs are lit: Battery charge level is

decreasing. Stop work as soon as possible.

• 1 level monitoring LED is lit: Battery is at. Stop work

IMMEDIATELY and charge the battery. Otherwise the

battery’s service life will be greatly shortened.

NOTE: If the charge level button does not appear to be

working, insert the charger and charge as needed.

NOTE: Immediately after using the battery pack, the charge

level button may display a lower charge than it will if checked

a few minutes later. The battery cells “recover” some of their

charge after resting.

Charger Operation

mWARNING! Charge only 24V iON+ lithium-ion battery

packs with its compatible 24V iON+ lithium-ion charger. Other

types of batteries may cause personal injury and damage.

To reduce the risk of electric shock, do not allow water to ow

into the charger's AC/DC plug.

When to Charge the iON+ 24VBAT-LTE

Lithium-iON Battery

NOTE: The iON+ 24VBAT-LTE lithium-ion battery packs do

not develop a "memory" when charged after only a partial

discharge. Therefore, it is not necessary to run down the

battery pack before inserting the charger plug.

• Use the battery indicator lights to determine when to charge

your iON+ 24VBAT-LTE lithium-ion battery pack.

• You can "top-o" your battery pack's charge before starting

a big job or after a long day of use.

Charge level button

The battery is at 30% capacity

and requires charging

The battery is at 60% capacity

and requires charging soon

The battery is at full capacity

Light IndicatorsLights

Charging the Battery

1. Push the push lock button on the battery to pull the

battery pack out from the battery compartment (Fig. 1).

2. Check that the mains voltage is the same as that marked

on the rating plate of the battery charger. Then, plug the

charger adapter into an appropriate AC power outlet.

Connect the charger plug into the charge socket of the

battery to start charging (Fig. 2).

3. The battery will take approximately 1 hr 20 minutes

to charge. The battery indicator LEDs will twinkle and

illuminate one by one during the charging process.

Unplug the charger immediately when the 3 LEDs are all

illuminated.

mCAUTION! FIRE HAZARD. When disconnecting the

charger from the battery, be sure to unplug the charger from

the outlet rst, then disconnect the charger from the battery

mWARNING! This charger does not automatically

turn o when the battery is fully charged. Please take care

not to leave the battery plugged into the charger. Switch

o or unplug the charger at the mains when charging is

complete.

4. Timely recharging of the battery will help prolong the

battery's life. You must recharge the battery pack when

you notice a drop in the equipment's power.

IMPORTANT! Never allow the battery pack to become fully

discharged as this will cause irreversible damage to the

battery.

Assembly

mDANGER! Never start the motor before installing the

guide bar, chain, and chain/sprocket end cover. Without all

these parts in place, the clutch can y o or explode, exposing

the user to potentially serious injuries.

Installing/Replacing Guide Bar +

Cutting Chain

Tools and supplies required:

• Hex key wrench (provided)

• Heavy-duty work gloves

NOTE: When replacing the guide bar and chain, use only

identical replacement parts. Make sure the pole chain saw

is disconnected with the battery before proceeding with

installation.

1. Remove the hex bolt by screwing it counterclockwise with

the hex key wrench (Fig. 3).

2. Screw the chain/sprocket end cover knob

counterclockwise to release chain/sprocket end cover

(Figs. 4 – 5).

Fig. 1

Push button

Fig. 2

Battery

indicators

Chain/sprocket

end cover Hex bolt

Hex key wrench

Fig. 3

Fig. 4

Chain/sprocket

end cover Chain/sprocket

end cover knob

3. Remove the bar and chain from the mounting surface

(Fig. 6).

4. Remove the old chain from the bar.

5. Lay out the new saw chain in a loop and straighten

any kinks. THE SHARP SIDE OF THE TEETH MUST

FACE AWAY FROM YOU IN THE DIRECTION OF THE

CHAIN ROTATION INDICATED ON THE GUIDE BAR

. If the teeth face backwards,

turn the loop over (Fig. 7).

6. Starting at the tip, mount the chain drive links into the

bar groove, leaving a loop at the back of the bar. The

chain will loosely t until it is placed on the sprocket

(Figs. 8 – 9).

NOTE: Make certain of the direction of the chain

If the chain is mounted

backwards, the saw will vibrate abnormally and will not cut.

7. Hold the chain in position on the bar and place the loop

around the sprocket. Fit the bar ush against the mounting

surface so that the bar studs are in the long slot of the bar

and the adjusting pin is in the chain tension pin hole

(Fig. 10).

8. Replace the chain/sprocket end cover by positioning the

cover onto the saw head. Tighten the end cover knob,

but leave the bar free to move for tension adjustment.

Put back the hex bolt by screwing it clockwise with the

hex key wrench.

9. Remove all slack from the chain by turning the chain

tensioner ring clockwise until the chain seats snugly

against the bar with the drive links in the bar groove

(Fig. 11).

Chain/sprocket

end cover

Fig. 5

Cutting chain

Guide bar

Fig. 6

Chain rotation

Sharp cutting edge

Chain drive link

Fig. 7

Fig. 8

Loop

Fig. 9

Sprocket

Adjusting pin

Chain tension

pin hole

Fig. 10

NOTE: The chain is correctly tensioned when there is no

sag on the underside of the guide bar; the chain is snug,

but can be rotated by hand without binding. For more

information on chain tensioning, see the maintenance

section beginning on pg. 16.

Connecting to the Telescoping Pole

1. Open the assembly lock on the telescoping pole, and

push the chain saw head into the opening on the end of

the pole (Fig. 12).

2. When the lock tabs snap in, lock back the assembly lock,

the pole chain saw will be ready to use (Fig. 13).

3. To remove the chain saw head, release the On/O trigger

switch and remove the battery. Unlock the assembly lock.

Push the lock tabs on both sides, and pull the chain saw

head out (Fig. 13).

Operation

Starting and Stopping

1. Slide the battery into the battery compartment until it

clicks to lock it into position (Fig. 14).

2. To turn the pole chain saw ON, push and hold the safety

lock switch (located on the handle) forward with your

thumb and then squeeze the On/O trigger switch with

your ngers. Once the tool is running, you can release the

safety lock switch (Fig. 15).

3. To turn the tool OFF, release the On/O trigger switch

(Fig. 15).

Adjusting the Telescoping Pole

This machine is equipped with a telescoping pole which

provides up to 14 ft (4.3 m) of overhead reach. To adjust the

telescoping pole, follow the instructions below.

1. Disconnect the saw from the power supply by removing

the battery from the compartment.

2. Unclip the telescoping lock to release the pole. Extend the

pole to the desired length (Fig. 16).

NOTE: Push poles toward each other to shorten the pole

or pull them away from each other to lengthen the pole.

Only extend the pole to the minimum length required to

reach the limb.

Fig. 11

Chain/sprocket

end cover Chain tensioner

ring

Fig. 12

Telescoping pole

Assembly lock

Chain saw head

Fig. 13

Lock tab

Assembly lock

Fig. 14

Battery

Fig. 15

On/O trigger switch

Safety lock

switch

3. Lock the pole in position by closing the telescoping lock

(Fig. 17), and ensure that the pole is secured.

mWARNING! Failure to lock the telescoping lock as

directed could result in personal injury.

Adjusting the Multi-Angle Head

The pole chain saw head can be rotated for dierent cutting

angles for 0º, 15º, and 30º (Fig. 18). Follow the below

instructions to adjust angles.

1. Rotate the chain saw head to the desired cutting angle

while pressing the rotating buttons located on both sides

simultaneously (Fig. 19).

2. Release the buttons when the chain saw head is set to the

desired angle.

NOTE: Failure to properly secure the chain saw head may

result in personal injury and/or property damage.

mWARNING! Always ensure the chain saw head is

securely locked! Do not attempt to use the pole chain saw with

the head in any other position or unlocked!

Adjusting the Auxiliary Handle

The chain saw is equipped with an auxiliary handle that can be

adjusted and removed. Follow the instruction below to operate

the auxiliary handle

mWARNING! Make sure the knob, bolt, and the screws

are xed into place. Failure to lock any of them as directed

could result in personal injury or property damage.

To Remove the Auxiliary Handle

1. Disconnect the saw from the power supply by removing

the battery from the compartment.

2. Unscrew the auxiliary handle lock knob and remove it and

the bolt, then the auxiliary handle can be pulled out

(Fig. 20).

Fig. 16

Pull Pull

Telescoping lock

Fig. 17

Telescoping lock

Fig. 18

0º

15º

30º

Fig. 19

Rotating button

Front Side

Back Side

Rotating button

Fig. 20 Auxiliary handle

Auxiliary handle

lock knob

Bolt

3. Re-assemble the auxiliary handle lock knob and the bolt

on (Fig. 21).

To Adjust the Position of the Auxiliary Handle

1. Disconnect the saw from the power supply by removing

the battery from the compartment.

2. Remove the auxiliary handle lock knob, the bolt, and the

auxiliary handle. Use a screw driver to remove the two

screws that used to x the auxiliary handle loops.

Remove the loops from the pole (Fig. 22).

3. Re-assemble the auxiliary handle loop on the desired spot

on the pole by using the two screws, and put back the

auxiliary handle, the auxiliary handle lock knob and the

bolt (Fig. 22).

To Adjust the Angle of the Auxiliary Handle

1. Stop the saw by releasing the On/O switch.

2. The auxiliary handle can be adjusted in -45°, 0°, 45°.

Rotate the auxiliary handle lock knob to unlock the handle,

and then rotate the handle to the desired angle (Fig. 23).

3. Rotate the auxiliary handle lock knob back to lock the

handle in position.

Cutting Tips for Pole Chain Saw

mCAUTION!

• Before starting the saw, remove the oil tank cap and add

bar & chain oil to the top of the oil level window (Fig. 24).

One minute of use will consume approximately 0.15  oz

(4 ml) of oil. Rell when the oil level drops to 1/4 of a tank.

NOTE: Your pole chain saw head is equipped with an

automatic oil pump for bar and chain oiling. You must add

bar and chain oil or your pole chain saw will not function.

mWARNING! Be sure that the chain is not in contact with

any object when you start the motor.

mWARNING! Keep hands away from chain. Keep hands

on handles. Do not overreach.

A good, rm grip on the tool using both hands will help you

maintain control. Place one hand on the soft grip or the

telescoping pole, and the other hand on the handle with your

thumbs and ngers encircling the pole and handle. A rm grip

combined with proper positioning of the handle against your

body will help you maintain control of the saw. Do not let go of

the saw while it is in operation.

mCAUTION! The chain will continue to run for several

seconds after turning o the tool.

Do not use the pole chain saw under wet conditions. Use

extreme caution when cutting small brush, saplings, or limbs

under tension because slender and tense material may catch

the saw and be whipped toward you, pull you o balance, or

spring back.

Do not use the pole chain saw to cut vines and/or small

underbrush.

Prior to each cutting session, run through the daily checklist

(see pg. 18).

Fig. 21

Fig. 22 Auxiliary handle

Auxiliary

handle

lock knob

Bolt

Auxiliary

handle loop

Screws

Auxiliary

handle loop

Fig. 23

Auxiliary handle

lock knob

Fig. 24

Oil tank cap

Oil level

window

mWARNING! Do not cut trees near electrical wires.

mWARNING! Failure to lubricate the chain will cause

damage to the bar and chain. Use only a good quality bar

and chain oil designed specically for use with chain saws.

One minute of use will consume approximately 0.15  oz.

(4 ml) of oil.

NOTE: It is normal for oil to seep from the saw when not in

use. To prevent seepage, empty the oil tank after each use.

When storing the unit for a long period of time (3 months or

longer), be sure the chain is lightly lubricated; this will prevent

rust on the chain and bar sprocket.

mWARNING! Kickback may occur when the moving

chain contacts an object at the upper portion of the tip of

the guide bar or when the wood closes in and pinches the

chain saw in the cut (Fig. 25). Contact at the upper portion

of the tip of the guide bar can cause the chain to dig into

the object and stop the chain for an instant. The result is a

lightning-fast reverse reaction, which kicks the guide bar up

and back toward the operator. If the chain saw is pinched

along the top of the guide bar, the guide bar can be driven

rapidly back toward the operator. Either of these reactions

can cause loss of saw control, which can throw the operator

o balance and result in serious injury. Do not rely exclusively

upon the safety devices built into the saw. As a user, you

should take several precautions to keep your cutting jobs free

from accident or injury.

Proper Cutting Stance

• Balance your weight with both feet on solid ground.

• Your body should always be to the left of the chain line.

• The most typical cutting application is to position the

unit at an angle of 60° or less depending on the specic

situation (Fig. 26). As the angle of the pole chain saw shaft

to the ground increases, the diculty of making the rst

cut (from the underside of limb) increases.

Basic Cutting Procedure

This unit with the chain saw head is designed for trimming

small branches and limbs up to recommended 6.5 in.

(16.5 cm), not to exceed a Max. cut of 7.5 in. (19 cm) in

diameter depending on type of wood. Practice cutting a few

small limbs using the following technique to get the “feel” of

using the saw before you begin a major sawing operation.

• Take the proper stance in front of the tree with the

saw OFF (Fig. 26).

• Squeeze the On/O trigger switch and let the chain

accelerate to full speed before entering the cut.

• Keep the saw running the entire time you are cutting;

maintain a steady speed.

• Allow the chain to cut for you; exert only light downward

pressure. If you force the cut, damage to the bar, chain, or

unit can result.

• PUSH and PULL – This reaction force is always opposite

to the direction the chain is moving when it is in contact

with the wood. Thus, the operator must be ready to

control the PULL when cutting on the bottom edge of the

bar, and PUSH when cutting along the top edge.

• Do not put pressure on the saw at the end of the cut.

KICKBACK DANGER ZONE

Fig. 25

Fig. 26

60º MAXIMUM

Pruning

Pruning is the process of trimming limbs from a live tree.

• Remove long branches in several stages.

• Cut lower branches rst to allow the top branches more

room to fall.

• When pruning trees, it is important not to make the

nishing cut next to the main limb or trunk until you have

cut o the farthest lying limb. This will reduce the weight

and prevent stripping the bark from the main member.

• Under cut the branch 1/3 through for your rst cut.

Your second cut should over cut to drop the branch o

(Fig. 27). Be prepared to balance the weight of the pole

chain saw when the limb falls.

• When re-starting the motor, always keep the ON/O

trigger switch pressed.

NOTE: The motor only runs when the ON/O trigger

switch is operated and shuts o when the ON/O trigger

switch is released.

• Now make your nishing cut from the topside of the

branch smoothly and neatly against the main member so

the bark will grow back to seal the wound.

• Release the On/O trigger switch as soon as the cut is

completed. Failure to follow proper cutting procedures will

result in the bar and chain binding and becoming pinched

or trapped in the limb.

Limbing

Limbing is the process of removing branches from a fallen tree.

• You should cut limbs one at a time. Remove the cut limbs

from the work area often to help keep the work area clean

and safe.

• Cut branches under tension from the bottom up to avoid

binding the bar and chain.

• Keep the tree between you and the pole chain saw while

limbing. Cut from the side of the tree opposite the branch

you are cutting.

If the Saw Becomes Pinched or Trapped

1. Wait for the blade to stop, wait ve minutes for the saw to

cool, remove the battery, and wear gloves to protect your

hands from the chain teeth.

2. If you can reach the limb from the ground, lift the limb

while holding the saw. This should release the “pinch” and

free the saw.

3. If the saw is still trapped, call a professional for assistance.

Maintenance + Care

mWARNING! Always remove the battery before

performing any adjustments, maintenance, or repairs to your

cordless pole chain saw.

• Use protective gloves when handling the bar and chain.

• Keep the bar encased in its sheath, except when working

directly on the bar or the chain.

• Never dispose of oils or other polluting materials in

unauthorized places.

Chain Tension

Check the chain tension before using the saw when the chain

is cold. The correct tension of a cold chain is when there is no

slack on the underside of the guide bar; the chain is snug, but

you can rotate it by hand without binding.

During normal saw operation, the temperature of the chain will

increase. The drive links of a correctly tensioned warm chain

will hang approximately 0.050 in. (1.25 mm) out of the bar

groove (Fig. 27). Be aware that a chain tensioned while warm,

may be too tight upon cooling. Check the “cold tension” before

next use. The chain must be re-tensioned whenever the ats

on the drive links hang out of the bar groove (Fig. 28).

NOTE: A new chain tends to stretch. Check the chain tension

frequently and re-tension as needed.

Load

Second Cut

First Cut

1/3 Diameter

Finishing Cut

Fig. 27

Properly Adjusted Warm Chain

Approximately 0.050 in. (1.25 mm)

Flats are

visible here

Flats are not

visible here

Chain Needs Tensioning

Fig. 28

Nuts and Screws

Periodically check that all the nuts and screws are tightened

securely. Check that the telescoping lock and assembly lock

are intact and in proper working order.

Chain Sharpening

mWARNING! To ensure that the saw works safely and

eciently, it is essential that the cutting components are

well-sharpened. It is highly recommended to replace the

chain once it loses its ability to cut cleanly and safely.

It is possible, however, to sharpen the existing chain if the

sharpening is carefully performed. Any work on the chain

and bar requires specic experience and special tools. For

safety purposes, we recommend you contact an authorized

Snow Joe® + Sun Joe® dealer or call the Snow Joe® +

Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563).

Sharpening is necessary when:

• The sawdust looks like dust;

• Cutting becomes more dicult;

• The cut is not straight;

• Vibrations increase.

An authorized service center will sharpen the chain using the

right tools to ensure minimum removal of material and even

sharpness on all the cutting edges.

If you sharpen the chain yourself, use special round-section

les with the right diameter depending on the type of chain

(see “Chain Maintenance Table”). You need a certain amount

of skill and experience to avoid damaging the cutting edges.

Sharpen the chain as follows (Fig. 29):

• Secure the bar rmly, with the chain mounted, in a

suitable vise.

• Tighten the chain if it is loose.

• Mount the le in the guide and then insert it in the tooth at

a constant angle from the cutting edge.

• Sharpen in a forward motion a few times and repeat this

on all the cutting edges facing the same way (right or left).

• To move the chain forward, use a screwdriver.

• Turn the bar over in the vise and repeat on all the other

cutting edges.

• Check that the depth limiter tooth does not stick out

farther than the inspection tool and le any projecting

parts with a at le, rounding o the edges (Fig. 29).

• After sharpening, remove all traces of ling and dust

and lubricate the chain in an oil bath. Replace the chain

whenever:

– The length of the cutting edges decreases to 5 mm

or less;

– There is too much play between the links and the rivets.

Guide Bar Maintenance

When the guide bar shows signs of wear, turn it over on the

saw to distribute the wear for maximum bar life. Feathering or

burring of the bar rails is a normal process of bar wear. You

should smooth such faults with a le as soon as they occur.

Replace a bar with any of the following faults:

• wear inside the bar rails permitting the chain to

lay over sideways

• bent guide bar

• cracked or broken rails

• spread rails

Turn the saw over, check the underside of the guide bar,

and make sure that the lubrication holes and chain groove are

free from impurities.

Inspection tool

Depth limiter tooth

Cutting edge

Depth

limiter

tooth

Fig. 29

Chain Maintenance Table

3/8

inches mm

Drive Links Chain Pitch Chain Gauge File Diameter

inches mm inches mm

9.5 0.050 1.3 45/32

Chain Sprocket

Regularly check the condition of the sprocket and replace it

when wear exceeds 0.5 mm (Fig. 30).

Do not mount a new chain with a worn sprocket or vice-versa.

Troubleshooting

Troubleshooting Tips

Most diculties are easy to x. Consult the troubleshooting

table for common problems and their solutions. If you continue

to experience problems or need repairs beyond these minor

adjustments, please call 1-866-SNOWJOE (1-866-766-9563)

for assistance.

mWARNING! Always remove the battery before

performing any adjustments, maintenance, or repairs to your

cordless chain saw.

Troubleshooting Table

Daily Checklist, Cleaning

and Storage

Daily Checklist

To help maintain your pole chain saw for optimum

performance, we recommend you complete this checklist prior

to each work session.

mWARNING! Do not insert the battery until you have

completed all of the daily checks.

• Inspect for any visible damage to the chain, guide bar, or

motor housing.

• Inspect the oil port and guide bar rails and clean them to

remove any debris.

• Check the chain tension.

• Check the chain teeth for sharpness.

• Check the bar and chain oil level; ll with only new chain

oil specically formulated for chain saws.

NOTE: If you notice anything unusual, such as a vibration or an

odd sound, shut the saw OFF immediately. Remove the battery

and check the saw for any damage.

If you cannot nd the cause of the problem or are uncertain

what to do, then have the saw inspected by an authorized

Snow Joe® + Sun Joe® dealer or call the Snow Joe® +

Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563) before using it.

mCAUTION!

• Remove the battery and wait at least ve minutes for the

saw to cool before servicing or storing your unit.

• If you drop the saw, carefully inspect it for damage. If the

guide bar is bent, the housing is cracked, the handle is

broken, or if you see any other condition that may aect

the saw’s operation, DO NOT USE the tool. Instead, have

it serviced at an authorized Snow Joe® + Sun Joe®

dealer or call the Snow Joe® + Sun Joe® customer service

center at 1-866-SNOWJOE (1-866-766-9563).

Disposal

Recycling the tool

• Do not dispose of electrical appliances as unsorted

municipal waste. Use separate collection facilities.

• Contact your local government agency for information

regarding the collection systems available.

• If electrical appliances are disposed of in landlls

or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your

health and well-being.

• When replacing old appliances with new ones, the retailer

is legally obligated to take back your old appliance for

disposal at least free of charge.

< 0.5 mm

Fig. 30

Problems Corrective Action

The saw

motor fails

to start

• Check that you have inserted the battery properly

and the battery has enough power to work.

• Make sure that you fully depress, push forward

and hold the safety lock switch before squeezing

the ON/OFF trigger switch.

• The chain is too tight; re-tension.

• The chain tension is too tight; re-tension.

• The chain oil tank is empty; rell.

• The lubrication holes are plugged; clean them out.

• The chain tension is too tight; re-tension.

• The guide bar or chain is damaged; inspect

and replace the damaged part.

The saw

runs, but

the chain

speed is

low

Bar and

chain

running

hot and

smoking

The saw

motor

runs, but

the chain

is not

turning

Recycling + Disposal

The product comes in a package that protects it against

damage during shipping. Keep the package until you are

sure that all parts have been delivered and the product is

functioning properly. Recycle the package afterwards or keep it

for long-term storage.

WEEE symbol. Waste electrical products should not

be disposed of with household waste. Please recycle

where facilities exist. Check with your local authority

or local store for recycling regulations.

Battery Caution + Disposal

Always dispose of your battery pack according to federal,

state, and local regulations. Contact a recycling agency in your

area for recycling locations.

mCAUTION! Even discharged battery packs contain

some energy. Before disposing, use electrical tape to cover

the terminals to prevent the battery pack from shorting, which

could cause a re or explosion.

mWARNING! To reduce the risk of injury or explosion,

never burn or incinerate a battery pack even if it is damaged,

dead or completely discharged. When burned, toxic fumes and

materials are emitted into the surrounding atmosphere.

1. Batteries vary according to device. Consult your manual

for specic information.

2. Install only new batteries of the same type in your product

(where applicable).

3. Failure to insert batteries in the correct polarity, as

indicated in the battery compartment or manual, may

shorten the life of the batteries or cause batteries to leak.

4. Do not mix old and new batteries.

5. Do not mix Alkaline, Standard (Carbon-Zinc) or

Rechargeable (Nickel Cadmium, Nickel Metal Hydride, or

Lithium-Ion) batteries.

6. Do not dispose of batteries in re.

7. Batteries should be recycled or disposed of as per state

and local guidelines.

Support

If your Sun Joe® iON+ 24V-PS8-LTE cordless pole chain saw

requires service or maintenance, please call 1-866-SNOWJOE

(1-866-766-9563) for assistance.

Model + Serial Number

When contacting the company, reordering parts, or arranging

service from an authorized dealer, you will need to provide the

model and serial numbers, which can be found on the decal

located on the housing of the unit. Copy these numbers into

the space provided below.

24VCHRG-AC

Federal Communications Commission

(FCC)

mWARNING! Any changes or modications to this

unit not expressly approved by the party responsible for

compliance could void the user's authority to operate the

equipment.

Class B device:

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur

in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit dierent

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Record the following numbers from the housing or handle of your

new product:

2 4 V - P S 8 - L T E

Model #:

Serial #:

Optional Accessories

mWARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use

replacement parts or accessories that are not intended for use with this cordless pole chain saw. Contact Snow Joe® +

Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your cordless pole chain saw.

The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such

changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

24V iON+ 2.0 Ah Lithium-Ion Battery

24V iON+ 2.5 Ah Lithium-Ion Battery

24V iON+ 4.0 Ah Lithium-Ion Battery

24V iON+ 5.0 Ah Lithium-Ion Battery

24V iON+ lithium-ion Battery Quick Charger

24V iON+

lithium-ion Dual Port Battery Charger

8 in. (20.3 cm) chain

8 in. (20.3 cm) bar

24VBAT-LTE

24VCHRG-QC

24VCHRG-DPC

SWJ-8CHAIN

SWJ-8BAR

SJWB

24VBAT-LT

24VBAT

24VBAT-XR

ModelAccessories Item

Universal Wall Bracket

with Mounting Hardware

La page charge ...

Sun Joe 24V-PS8-LTE Manuel utilisateur

Marque: Sun Joe

Modèle: 24V-PS8-LTE

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sun Joe 24V-PS8-LTE User manual
español: Sun Joe 24V-PS8-LTE Manual de usuario

Sun Joe 24V-PS8-LTE Manuel utilisateur

Sun Joe 24V-PS8-LTE Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents