Yale Smart Safe
Installation Instructions
If you have any questions while installing, call our 24/7 tech support team! Call 1-855-213-5841 or email Support@YaleLock.com
Tip: If you already use the
August App, use the same
username and password.
YRSF-MD-MNL-0020 Rev B Part of ASSA ABLOY
1Download the Yale Access App
Create an account
Open the battery
compartment and
insert 4 AA batteries.
Reinstall the cover.
2Unlock Safe Using Key
Open door and leave open
until setup is complete.
Tip: When key is used to
unlock, it must be used to
lock.
Insert Batteries
3
Set up Smart Safe
Tap "Set up a device" from the app menu. When asked,
scan the Yale QR code on the inside of your safe door.
Tip: Once batteries are inserted, you have 10 minutes
to complete this step. If your app doesn't find the safe,
press and hold (5 secs) the reset button on the inside
of the safe door.
Set up Connect*
Note serial number located on back of Connect. Plug Connect
into an INDOOR outlet within 10 feet of the Smart Safe.
Tip: For best connectivity, make sure that the Connect bridge
is in the line of sight of the front of the safe.
Add Safe to the Yale Access App
*Connect WiFi Bridge included with select models
4
OMount Safe For Added Security (Optional)
There are 8 mounting hole locations on the Smart
Safe. Use included mounting template for guidance
to secure the safe to the wall, shelf or floor.
Tips:
• Use Phillips #2 screwdriver to tighten screws.
• To avoid scratching or damaging your floor, attach
the included 4 rubber feet to the bottom of the safe
with the 3M side against safe.
optional
Pour la version francaise voir US.YaleHome.com/Support
Key
x4
Mounting
Hardware
Needed for Optional Installation
Drill with
3/8" Drill Bit Pencil
x4
AA Batteries
(Alkaline only)
Connect WiFi Bridge
(Included with Select Models)
Phillips #2
Screwdriver
x4
Rubber Feet
Once added to the Yale Access App,
you can create and delete
entry codes or share app access by
tapping the Guest icon in the
bottom menu.
Create Entry Codes
5
Using Your Smart Safe
9 Volt Battery Back-up
(Use Alkaline battery)
Hold battery to quickly recharge.
Keyhole
Cover
Outside
LED Keyhole
Enter/Unlock
(Set/Continue)
Safe
Wake Up /
Settings
Settings Definitions
YRSF-MD-MNL-0020 Rev B Part of ASSA ABLOY
Warning: Changes or modifications to this device not expressly approved by
Yale Home could void the user's authority to operate the equipment.
Yale® is a registered trademark of Yale Home. Use of the Works with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge and has been
certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Other products' brand names
may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. © Copyright 2021. All rights reserved. Reproduction in whole or in part without the
express written permission of Yale Home is prohibited.
24/7 Support 1-855-213-5841 • US.YaleHome.com
Yale Home
FCC ID: 2ABFG-IESD100PG0
FCC
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications (including the antennas) to
this device that are not expressly approved by the
manufacturer may void the user's authority to operate the
equipment.
Note : This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications, However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
Modifications not expressly approved by the manufacturer
could void your authority to operate the equipment under
FCC rules.
IC ID: 11626A-IESD100PG0
ISED
This device contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le
présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
FCC and IC RF Radiation Exposure Statement:
This equipment complies with FCC and IC RF Radiation
exposure limits set forth for an uncontrolled environment.
This device and its antenna must not be co-located or
operating in conjunction with any other antenna or
transmitter.
RF du FCC et IC d'exposition aux radiations:
Cet équipement est conforme à l'exposition de FCC et IC
rayonnements RF limites é-tablies pour un environnement
non contrôlé.
L’antenne pour ce transmetteur ne doit pas être même
endroit avec d’autres émetteur sauf conformément à FCC et
IC procédures de produits Multi-émetteur.
While in Privacy Mode, the
safe will not open even
when a valid Entry Code is
entered. This setting can
be changed from the Yale
Access App.
The inside light will
automatically turn on and
stay on for 10 seconds
when the safe door is
opened.
Setting Default Definition
Privacy
Mode
Inside Light
One Touch
Locking
Sound On
On
This setting cannot
be turned off.
On
This feature cannot
be turned off.
Off
The sound setting for entry
code verification can be set
from the Yale Access App.
Inside
LED
Battery
Compartment
Key
Hooks
Reset Button*
(Factory Settings)
* When safe is paired to app, Factory Reset must be done
from app. During a factory reset the safe will be unlocked.
Low Battery Warning
Safe can always be opened with the key
or with a 9V battery and valid code.
Touching any key on
keypad will lock the safe.
Locking Safe
Close Safe Door
Press any key to lock safe
Unlocking Safe
Enter valid 4-6 digit code
Press
-
1
-
2
Yale IESD100PG0 Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Yale IESD100PG0 User manual
Documents connexes
-
Yale Assure Lock SL Key Free Touchscreen Deadbolt YRD256 Mode d'emploi
-
Yale Security YRCB-490-CB1-WSP Manuel utilisateur
-
-
August YALE-AYR202-ZB-HA Guide d'installation
-
August YALE-AYR202-ZWV-USA Guide d'installation
-
Yale YRBDGCB2 Manuel utilisateur
-
-
-