MTD OEM-190-180A Manuel utilisateur

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Printed In USA

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

Op e r a t O r ’s Ma n u a l

Twin Rear Bagger - Model No. OEM-190-180A & 19A30002000

11/18 / 2008

FORM NO. 769-04317

To The Owner

1

2

Thank you for purchasing a double bagging attachment

manufactured by MTD LLC. It was carefully engineered to

provide excellent performance when properly operated and

maintained.

Please read this entire manual prior to operating the equipment.

It instructs you how to safely and easily set up, operate and

maintain this attachment. Please be sure that you, and any

other persons who will operate the machine, carefully follow the

recommended safety practices at all times. Failure to do so could

result in personal injury or property damage.

All information in this manual is relative to the most recent

product information available at the time of printing. Review this

manual frequently to familiarize yourself with the attachment,

its features and operation. Please be aware that this Operator’s

Manual may cover a range of product specifications for various

models. Characteristics and features discussed and/or illustrated

in this manual may not be applicable to all models. MTD LLC

reserves the right to change product specifications, designs and

equipment without notice and without incurring obligation.

If you have any problems or questions concerning this

attachment, phone your local authorized MTD service dealer

or contact us directly. MTD’s Customer Support telephone

numbers, website address and mailing address can be found on

this page. We want to ensure your complete satisfaction at all

times.

Throughout this manual, all references to right and left side of the

machine are observed from the operating position

Thank You

Customer Support

Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.

If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of

this machine, you can seek help from the experts. Choose from the options below:

Visit us on the web at www.mtdproducts.com◊

Call a Customer Support Representative at (800) 800-7310 or (330) 220-4683◊

Write us at MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019◊

Record Product Information

Before setting up and operating your new equipment, please

locate the model plate on the equipment and record the

information in the provided area to the right. From the operator’s

position, locate the model plate in the front, left portion of the

plastic grass catcher cover. This information will be necessary,

should you seek technical support via our web site, Customer

Support Department, or with a local authorized service dealer.

MO d e l nu M b e r

se r i a l nu M b e r

Identify The Model of Tractor ................................. 3

Safe Operation Practices ........................................ 4

Carton Contents & Hardware Packs ...................... 7

Assembly & Installation .......................................... 9

Operation ................................................................16

Parts List ..................................................................18

Warranty ................................................................ 20

Spanish ....................................................................21

French ......................................................................41

Table of Contents

3se c t i O n 1 — tO th e Ow n e r

Identify The Model of Tractor

This manual is designed for installation of this new bagging unit

on several different models of tractors. It is important for you

to determine which model of tractor that you have. Once this is

known, follow the pertinent set of instructions on the following

pages.

Note: Read and observe all WARNING, NOTES and IMPORTANT

statements. They are included to provide for the protection of

the equipment installer and user, and to ensure the prolonged

service life of the equipment.

Note: References to LEFT and RIGHT indicate the left and

right sides of the tractor when facing forward in the operator’s

position. Reference to the FRONT indicates the grille end; to the

REAR, the rear end of the rider.

To determine which model of rider you have, you will need to

locate the rider’s model plate, located under the seat. Simply flip

the seat up and locate the model plate, which will consist of an

11 digit/letter model number and a serial number. See Fig. 1-1.

For ease in this installation and for future use, copy your rider’s

model number & serial number below now:

Rider Model Number:__ __ __ __ __ __ __ __ __ __ __

Rider Serial Number:_________________________

The 5th, 6th & 7th numbers from the left in your model number

determine your rider’s model series. See Fig. 1-2.

When you fill in your model number in the space above, the

actual model series number should fall into the gray shaded area.

Now that you have determined what model rider you are

attaching this grass bag collection system to, follow the

instructions on the following pages according to your model of

rider.

w

w.m t

d

p

ro

d

u

c

t

s

.c

om

M

T

D

L

C

P

.

O

.

B

O

X

3

6

1

3

1

C

L

E

V

E

L

A

N

D

,

O

H

44136

3

0

-

2

0

-

4

6

8

3

8

0

-

8

0

-

7

3

1

0

Model Plate

Figure 1-1

Figure 1-2

1 3 A M 7 9 0 G 0 0 0

Indicates Model Series 700

Sample Model Number

Important Safe Operation Practices

2

4

General Operation

Read, understand, and follow all instructions on your 1.

equipment and in their manuals before attempting to

assemble and operate. Keep this manual in a safe place for

future and regular reference and for ordering replacement

parts.

To help avoid blade contact or a thrown object injury, keep 2.

bystanders, helpers, children and pets at least 75 feet from

the mower while it is in operation. Stop machine if anyone

enters the area.

Thoroughly inspect the area where the equipment is to be 3.

used. Remove all stones, sticks, wire, bones, toys, and other

foreign objects which could be picked up and thrown by

the blade(s). Thrown objects can cause serious personal

injury.

Always wear safety glasses or safety goggles during 4.

operation and while performing an adjustment or repair

to protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

Do not operate the mower without the discharge cover 5.

or entire grass catcher in its proper place. A missing

or damaged discharge cover or grass bag attachment

component may result in thrown objects or blade contact

injuries.

Do not put hands or feet near rotating parts or under the 6.

cutting deck. Contact with the blade(s) can amputate

hands and feet.

Shut off mower’s engine and wait for blades to come to 7.

a complete stop before unclogging mower’s discharge

opening or bagger parts.

Slow down before turning. Operate the machine smoothly. 8.

Avoid erratic operation and excessive speed. Be aware

that a grass catcher attachment can affect the handling

characteristics of your mower.

Disengage blade(s), set parking brake, stop engine and wait 9.

until the blade(s) come to a complete stop before opening

bagger attachment’s top cover, removing grass catcher,

emptying grass, unclogging chute, removing any grass or

debris, or making any adjustments.

Never leave a running machine unattended. Always turn 10.

off blade(s), place transmission in neutral, set parking

brake, stop engine and remove key before dismounting.

Your machine is designed to cut normal residential grass of 11.

a height no more than 10”. Do not attempt to mow through

unusually tall, dry grass (e.g., pasture) or piles of dry leaves.

Dry grass or leaves may contact the engine exhaust and/

or build up on the mower deck presenting a potential fire

hazard.

If situations occur which are not covered in this manual, use 12.

care and good judgment. Contact your customer service

representative for assistance.

Slope Operation

Slopes are a major factor related to loss of control and tip-over

accidents which can result in severe injury or death. Attachments

can also affect the stability of the machine. All slopes require

extra caution.

For your safety, use the slope gauge included as part of this

manual to estimate the angle of slopes before operating this

machine on a sloped or hilly area. If the slope is greater than 10

degrees as shown on the slope gauge, do not operate the mower

with the grass bag attachment installed on that area or serious

injury could result.

Do:

Mow up and down slopes, not across. Exercise extreme 1.

caution when changing direction on slopes.

Watch for holes, ruts, bumps, rocks, or other hidden 2.

objects. Uneven terrain could overturn the machine. Tall

grass can hide obstacles.

WARNING! This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow

all instructions in this manual before attempting to operate this machine. Failure to comply

with these instructions may result in personal injury.

When you see this symbol. HEED ITS WARNING!

DANGER! This attachment was built to be used according to the safe operation practices in

this manual. Carelessness or error on the part of the operator can result in serious injury.

Mowers are capable of amputating hands and feet and throwing objects. Failure to observe

the following safety instructions as well as the instructions provided with your mower, could

result in serious injury or death.

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s

Safety Symbols

This table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the

machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to

assemble and operate

STOP

Turn off the engine before opening the bagger cover.

Use slow speed. Choose a low enough speed setting so 3.

that you will not have to stop or shift while on the slope.

Tires may lose traction on slopes even though the brakes

are functioning properly. Always keep machine in gear

when going down slopes to take advantage of engine

braking action.

Follow the manufacturer’s recommendations for wheel 4.

weights or counterweights to improve stability.

Keep all movement on the slopes slow and gradual. Do 5.

not make sudden changes in speed or direction. Rapid

engagement or braking could cause the front of the

machine to lift and rapidly flip over backwards which could

cause serious injury.

Avoid starting or stopping on a slope. If tires lose traction, 6.

disengage the blade(s) and proceed slowly straight down

the slope.

Do Not:

Do not turn on slopes unless necessary; then, turn slowly 1.

and gradually downhill, if possible.

Do not mow near drop-offs, ditches or embankments. The 2.

mower could suddenly turn over if a wheel is over the edge

of a cliff, ditch, or if an edge caves in.

Do not try to stabilize the machine by putting your foot on 3.

the ground.

Do not use a grass catcher on steep slopes. 4.

Do not mow on wet grass. Reduced traction could cause 5.

sliding.

General Service

Before cleaning, repairing, or inspecting, make certain the 1.

blade(s) and all moving parts have stopped. Disconnect the

spark plug wire and ground against the engine to prevent

unintended starting.

Keep all nuts, bolts, and screws tight to be sure the 2.

equipment is in safe working condition.

Never tamper with your mower’s safety interlock system 3.

or other safety devices. Check their proper operation

regularly.

Never attempt to make adjustments or repairs while the 4.

mower’s engine is running.

Grass catcher components and the discharge cover are 5.

subject to wear and damage which could expose moving

parts or allow objects to be thrown. For safety protection,

frequently check components and replace immediately

with original equipment manufacturer’s (O.E.M.) parts only,

listed in this manual. Use of parts which do not meet the

original equipment specifications may lead to improper

performance and compromise safety!

Maintain or replace safety and instruction labels, as 6.

necessary.

WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s

Sight and hold this level with a vertical tree...

or a corner of a building...

or a fence post

Fold along dotted line (represents a 10° slope)

10°

Use this page as a guide to determine slopes where you may not operate safely.

WARNING! Do not operate your lawn mower with a bagger attachment on such slopes. Do not mow on inclines with a

slope in excess of 10 degrees (a rise of approximately six inches every 10 feet). A riding mower with a bagger attachment

could overturn and cause serious injury. Operate riding mowers up and down slopes, never across the face of slopes.

Contents of Carton

3

7

Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below

and shown in Fig. 2-1. Hardware part numbers are shown in parentheses.

Hitch Bracket Kit •

(3 brackets & Hardware Pack)

700 Series Mount Kit • (2 brackets & hardware)

Chute Tube Extension•

Hitch Support•

Discharge Chute Elbow•

Grass Catcher Cover Screen•

Grass Catcher Cover•

Two Grass Bag Assemblies•

Upper Chute Tube•

Upper Chute Support•

Hinge Cover Pin•

Upright Support•

Bag Support Assembly•

Three Hardware Packs •

(Detailed & Pictured on next page)

Figure 2-1

RH Bracket (783-05889)

LH Bracket (783-05890)

(8) Hex Bolts (710-04484)

(2) Shoulder Bolts (738-04267)

(2) Flange Lock Nuts (712-04065)

(2) Clevis Pins (711-0332)

(2) Click Pins (714-0145)

Hitch Bracket Kit

(3 Pcs. & Hardware Pack)

700 Series

Mounting Kit

Includes the

following parts:

Chute Tube

Extension

(731-06610)

Hitch Support

(783-05887)

Discharge Chute

Elbow

(731-04153A)

Grass Bag

Assemblies

(664-04096)

Hinge Cover Pin

( 711- 0 4 988)

Upright Support

(683-04519)

Bag Support

Assembly

(683-04461)

Upper Chute Tube

(631-04291)

Upper Chute

Support

(731-06497)

Grass Catcher

Cover

(631-04292)

Grass Catcher

Cover Screen

(731-06504)

RH Mount (789-00052)

LH Mount (789-00054)

Rear Attachment Bracket

(789-00053)

Carriage Bolts (4)

(710-0276)

Flange Lock Nuts

(4) (712-04063)

8 se c t i O n 3 — cO n t e n t s O f ca r t O n

CONTENTS OF HARDWARE PACK

This grass collector kit is shipped with three loose hardware packs enclosed and one hardware pack included in the mounting bracket kit.

Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis.

Hardware Pack 689-00091

Hardware Pack 689-00087

(4)

(1)

(4)

(1)

(2)

Hardware Pack included with 689-00080

(1)

(2)

(710-3008)

(710-0276)

(712-04063)

(710-3008)

(712-04063)

(711-0309A)

(714-0117)

(711-05063)

(736-0204)

(714-04040)

(726-3046)

(711-04069)

(712-04064)

(723-04008A)

Assembly & Installation

4

9

Figure 4-1

Figure 4-2

700 Series Tractors Only

If you are assembling this bagger unit for use on any model 700

series tractor you will need to install the two tractor mounting

brackets packed in your bagger kit. If you are installing this

bagger unit on any other tractor, disregard these steps and move

to Assemble Mounting Brackets on the next page.

To install these brackets on a model 700 series tractor, follow

these steps:

Install a shoulder bolt from your hardware pack on each 1.

bracket, securing them with flange lock nuts also included

in the hardware pack. Refer to Fig. 4-1.

Remove and discard the two screws in the lower frame as 2.

seen in Fig. 4-2.

Mount the 700 series tractor mounting brackets to your 3.

tractor using eight self-tapping hex screws included with

your kit by using the pre-drilled holes in your tractor’s

frame for the two top mounting bolts and the holes on the

lower frame where you previously removed and discarded

the screws. See Fig. 4-2.

When attaching the hitch bracket assembly to the tractor, 4.

secure with the clevis pin and clip pins called out in Fig. 4-2,

in addition to the clevis pin used in the hitch plate on the

following page.

Discard existing bolts and replace

with bolts from hardware pack

Secure bracket using eight 5/16-18 x .750

hex tap screws

Clevis pin used on all

700 series tractors

to further secure the

mounting assembly

10 se c t i O n 4 — as s e M b l y & in s t a l l a t i O n

Assemble Mounting Brackets

To assemble the universal mounting assembly, locate the

mounting assembly pack and follow these steps:

Attach the two hitch side brackets to the universal rear 1.

attachment bracket using four hex bolts and flange lock

nuts. With the hooks on the hitch side brackets pointing

down, the tabs on the universal rear attachment bracket

should be pointing upwards. See Fig. 4-3.

Note: This universal mounting bracket assembly is

designed to work with other available attachments, such

as a weight kit used in conjunction with the snow blade or

snow thrower attachment. Utilize the contact information

on page 2, or contact the retailer in which you purchased

this equipment, to find out more about available

attachments for your specific tractor.

Flip over assembly and mount the hitch support bracket 2.

to the mounting assembly as seen in Fig. 4-4.

Note: It might be easier during the mounting stage to

leave this hardware only finger tight to facilitate lining up

the hitch hole for the clevis pin. You will be instructed to

tighten this later in this manual if you chose to only finger

tighten this hardware now.

Note: The holes closest to the mounting hooks are to be

used for all 700 model series machines, while the two holes

closest to the cross mount are for all other models. The

hitch support bracket will need to be flipped to enable

alignment of the proper holes depending on the model of

machine this bagger is being installed on. See Fig. 4-4.

For all other models

For 700 models

Side View

Figure 4-3

Figure 4-4

Hole provided for clevis pins for all 700 series mountings

11se c t i O n 4 — as s e M b l y & in s t a l l a t i O n

Install the clevis pin from hardware pack 689-00087 into the 2.

tractor’s hitch and secure with a hairpin clip. See Fig. 4-8.

Note: The clevis pin can be fed down through the hitch

plate and secured underneath with the hairpin clip, or it

may be easier to feed the clevis pin up through the hitch

plate hole and secure with the hairpin clip on the topside.

The latter method may be preferred since it can be easier

to insert the hairpin clip. Either way will work, the decision

should be based on operator preference.

Note: If you decided to leave the hitch support only

finger tight during the assembly process, tighten all of the

hardware securely at this time.

If Mounting Assembly onto 700 Series Tractors

Note: Install two clevis pins through the mounting assembly and

secure to the 700 series mounting brackets installed earlier with

click pins provided in the hardware pack. Refer back to Fig. 4-3.

Assembling The Support Assembly

Locate the upright support bracket and the bag support

assembly. Assemble it by following these steps:

Lay the bag support assembly topside down with the 1.

mounting bracket portion facing upwards.

Insert the notched end of the vertical support bracket into 2.

the bag support assembly, as in Fig. 4-5, and secure with a

5/16-18 carriage bolt and 5/16-18 flange lock nut. See Fig.

4-6.

Mount Assembly on Tractor

Install mounting assembly on tractor as follows:

Place the hooked ends of the mounting assembly over 1.

the shoulder bolts, as in Fig. 4-7, on the tractor and line up

the hitch support bracket center hole with the hole on the

tractor’s hitch.

Align hole on bracket

with hole on tractor

Figure 4-5

Figure 4-7

Figure 4-8

Figure 4-6

12 se c t i O n 4 — as s e M b l y & in s t a l l a t i O n

Assembling Remaining Bagger Components

Now that the mounting brackets are assembled and are in place

on the tractor, follow these steps to assemble the remaining

bagger components.

Snap the plastic upper chute support in place by first 1.

clipping the side portion onto the bagger support rail with

the edge of the snap feature aligned with the red line, as

seen in Fig. 4-11.

Snap the front side of the chute support to the rail, as 2.

shown in the inset of Fig. 4-11.

Install the bagger hanger assembly onto the mounting 3.

assembly on the tractor by hooking it over the hitch plate

between the two tabs. See Fig. 4-9.

Secure the hanger assembly to the mounting assembly 4.

using a 5/16” bolt and flange nut provided. See Fig. 4-10.

Tabs

Top View

1

2

Figure 4-9

Figure 4-10

Figure 4-11

13se c t i O n 4 — as s e M b l y & in s t a l l a t i O n

Install the bagger screen into the bagger cover by first 3.

inserting the end closest to the side with the cutout into

the mounting hole, as in Fig. 4-12. Make sure to feed the

screen under the lip, as in Fig. 4-13.

Clip in the other side by pushing the screen into the 4.

provided cutout. See Fig. 4-13.

Install the bagger cover onto the bag support assembly, as 5.

seen in Fig. 4-14. The plastic cover goes inside of the two

mounting tabs.

Slide the hinge pin into the hole located on the mounting 6.

tab, as in Fig. 4-15. Use the cut-out window (See inset in

Fig. 4-15) to line up the hinge pin on the other side and

push pin all the way in until it reaches the end-stop. At this

point the pin clips into place and is secured by a tab in the

bagger cover. See Fig. 4-16.

Figure 4-12

Figure 4-13

Figure 4-14

Figure 4-16

Figure 4-15

Make sure screen sits

under the cover’s lip

14 se c t i O n 4 — as s e M b l y & in s t a l l a t i O n

Open Hood by pushing in on the rear, right-side tab with 7.

your right hand, as seen in 1 of Fig. 4-17, and lifting the cover

with your left hand in the center rear of the bagger cover, 2.

Install both bag assemblies with the tight mesh sides facing 8.

forward, onto the bag support brackets by inserting the

front edge in first, as seen in Fig. 4-18, and setting the back

edge down until it fits into the assembly.

Install the rubber chute strap on the chute elbow using the 9.

supplied clevis pin, washer and Bow-tie cotter pin. See Fig.

4-19.

Install the ball pin from your hardware pack into the hole in 10.

the front of the mower deck as seen in Fig. 4-20, and secure

with the supplied flange lock nut.

With the tractor’s discharge chute raised up and held open, 11.

install the chute elbow over the chute opening by placing

the top, rear edge of the chute elbow over the rear of the

deck opening, then pivoting the chute elbow down and

over the chute opening. See Fig. 4-21.

1

2

1

2

Figure 4-17

Figure 4-18

Figure 4-19

Figure 4-21

Figure 4-20

15se c t i O n 4 — as s e M b l y & in s t a l l a t i O n

Note: For the chute elbow to be properly installed, the

bottom edge must fall over the bottom of the deck

opening. See Fig. 4-22.

Secure the chute elbow to the tractor’s deck by hooking 12.

the chute strap onto the ball pin installed earlier on the

deck. See Fig. 4-23.

Install the chute adapter onto the chute elbow by lining up 13.

the tabs and sliding the adapter over the chute elbow, as

in Fig. 4-24. Secure the chute adapter by installing the two

ratchet clips included in the hardware pack in the holes

provided.

With the bagger cover open, install the upper chute over 14.

the chute adapter, and rest the top so that the chute

support sits in the upper chute groove. See Fig. 4-25.

Note: Make sure to align the upper chute with the ridges

on the bagger support bracket.

Figure 4-22

Figure 4-24

Figure 4-25

Figure 4-23

Operation

5

16

Bagger Usage

NOTE: When both grass bags are full, place the tractor on a firm,

level surface, disengage the PTO, turn the tractor engine off and

set the parking brake.

Flip Seat up.1.

Lift up grass bag cover as instructed on Page 14 in Step 7. 2.

Do not remove the chute tube assembly from the tractor.

Remove the grass bags by lifting these up and moving the 3.

bags away from the bag support assembly.

Empty the grass clippings at a proper disposal sight, use 4.

the handle at the bottom of each grass bag. Holding the

bag firmly, empty the contents

Replace grass bags, close lid, flip down seat, restart your 5.

tractor and resume cutting your grass.

Notes

6

17

18

7

6

10

33

700 Series Mount Kit

32

20

21

10

17

16

8

11

14

7

24

33

35

34

10

5

31

30

25

28

26

25

1

15

18

6

5

22

3

23

10

12

9

13

19

4

2

27

29

OEM-190-180A Parts List

19se c t i O n 7 — pa r t s li s t

Ref. Part Number Description

1. 631-04291 Upper Chute Assembly

2. 631-04292 Double Bagger Cover Assembly

3. 731-06497 Upper Chute Support

4. 731-06504 Bagger Cover Screen

5. 710-0276 Carriage Screw, 5/16-18 x 1.00”

6. 710-3008 Hex Head Screw, 5/16-18 x .75”

7. 711- 0 30 9A Clevis Pin, .62” Dia.

8. 711- 0 4 0 6 9 Grass-catcher Pin, 1/4-20

9. 711-05063 Clevis Pin, 5/16 x .75 Lg.

10. 712-04063 Flange Lock Nut, 5/16-18

11. 712-04064 Flange Lock Nut, 1/4-20

12. 714 - 0117 Internal Cotter Pin, .148 x 3.00

13. 714-04040 Bow-Tie Cotter Pin, 72

14. 723-04008A Chute Strap, 6.00 Lg.

15. 726-3046 Ratchet Clip, .250

16. 731-04153A Discharge Chute Elbow, 38”/42”

17. 731-06610 Bagger Chute Adapter, 7 In.

18. 736-0204 Flat Washer, .344 x .62 x .033

19. 783-05887 Universal Bracket Support, RT-99/

20. 664-04096 Grass-bag Assembly

21. 683-04461 Double Bag Support Assembly

22. 683-04519 Vertical Support Bracket

23. 711- 0 4 98 8 Cover Hinge Pin

24. 735-0246A End Plug

25. 710-04484 Tap Screw, 5/16-18 x .750

26. 710-0332 Clevis Pin, .50 x .78 Lg.

27. 712-04065 Flange Lock Nut, 3/8-16

28. 714-0145 Click Pin, .092 x 1.64 Lg.

29. 738-04267 Shoulder Screw, .625 x .412

30. 783-05889 Mounting Bracket, RH

31. 783-05890 Mounting Bracket, LH

32. 689-00101 Hitch Bracket Assembly

33. 789-00052 Hitch Bracket, RH

34. 789-00053 Rear Attachment Bracket

35. 789-00054 Hitch Bracket, LH

MANUFACTURER’S LIMITED WARRANTY FOR

GDOC-100167 REV. A

The limited warranty set forth below is given by MTD LLC with

respect to new merchandise purchased and used in the United States

and/or its territories and possessions, and by MTD Products Limited

with respect to new merchandise purchased and used in Canada and/

or its territories and possessions (either entity respectively, “MTD”).

“MTD” warrants this product (excluding its Normal Wear Parts and

Attachments as described below) against defects in material and

workmanship for a period of one (1) year commencing on the date

of original purchase and will, at its option, repair or replace, free of

charge, any part found to be defective in materials or workmanship.

This limited warranty shall only apply if this product has been

operated and maintained in accordance with the Operator’s Manual

furnished with the product, and has not been subject to misuse,

abuse, commercial use, neglect, accident, improper maintenance,

alteration, vandalism, theft, fire, water, or damage because of other

peril or natural disaster. Damage resulting from the installation or use

of any part, accessory or attachment not approved by MTD for use

with the product(s) covered by this manual will void your warranty as

to any resulting damage.

Normal Wear Parts are warranted to be free from defects in material

and workmanship for a period of thirty (30) days from the date of

purchase. Normal wear parts include, but are not limited to items

such as: batteries, belts, blades, blade adapters, tines, grass bags,

wheels, rider deck wheels, seats, snow thrower skid shoes, friction

wheels, shave plates, auger spiral rubber and tires.

Attachments — MTD warrants attachments for this product against

defects in material and workmanship for a period of one (1) year,

commencing on the date of the attachment’s original purchase or

lease. Attachments include, but are not limited to items such as:

grass collectors and mulch kits.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH

PROOF OF PURCHASE, through your local authorized service dealer.

To locate the dealer in your area:

In the U.S.A.

Check your Yellow Pages, or contact

MTD LLC at P.O. Box 361131,

Cleveland, Ohio 44136-0019, or call 1-800-800-7310, 1-330-220-

4683 or log on to our Web site at www.mtdproducts.com

.

In Canada

Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800-

668-1238 or log on to our Web site at www.mtdcanada.com.

This limited warranty does not provide coverage in the following

cases:

a. Log splitter pumps, valves, and cylinders have a separate one-

year warranty.

b. Routine maintenance items such as lubricants, filters, blade

sharpening, tune-ups, brake adjustments, clutch adjustments,

deck adjustments, and normal deterioration of the exterior finish

due to use or exposure.

c. Service completed by someone other than an authorized service

dealer.

d. MTD does not extend any warranty for products sold or exported

outside of the United States and/or Canada, and their respective

possessions and territories, except those sold through MTD’s

authorized channels of export distribution.

e. Replacement parts that are not genuine MTD parts.

f. Transportation charges and service calls.

g. MTD does not warrant this product for commercial use.

No implied warranty, including any implied warranty of

merchantability of ﬁtness for a particular purpose, applies after

the applicable period of express written warranty above as to the

parts as identiﬁed. No other express warranty, whether written or

oral, except as mentioned above, given by any person or entity,

including a dealer or retailer, with respect to any product, shall

bind MTD. During the period of the warranty, the exclusive remedy

is repair or replacement of the product as set forth above.

The provisions as set forth in this warranty provide the sole and

exclusive remedy arising from the sale. MTD shall not be liable

for incidental or consequential loss or damage including, without

limitation, expenses incurred for substitute or replacement lawn

care services or for rental expenses to temporarily replace a

warranted product.

Some states do not allow the exclusion or limitation of incidental

or consequential damages, or limitations on how long an implied

warranty lasts, so the above exclusions or limitations may not apply

to you.

In no event shall recovery of any kind be greater than the amount of

the purchase price of the product sold. Alteration of safety features of

the product shall void this warranty. You assume the risk and liability

for loss, damage, or injury to you and your property and/or to others

and their property arising out of the misuse or inability to use the

product.

This limited warranty shall not extend to anyone other than the

original purchaser or to the person for whom it was purchased as a

gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This limited

warranty gives you specific legal rights, and you may also have other

rights which vary from state to state.

IMPORTANT: Owner may be required to present proof of purchase to

obtain warranty coverage.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683

MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238

La page est en cours de chargement...

MTD OEM-190-180A Manuel utilisateur

Ce manuel convient également à

MTD OEM-190-180A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents