Skil ID572702 Le manuel du propriétaire
- Catégorie
- Outils électroportatifs
- Taper
- Le manuel du propriétaire
WARNING: To reduce the risk of injury, the user must read and understand the
Owner’s Manual before using this product. Save these instructions for future reference.
AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et
comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide
afin de pouvoir le consulter ultérieurement.
ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender
el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para
consultarlas en caso sea necesario.
Owner’s Manual
Guide d’utilisation
Manual del propietario
For Customer Service
Pour le service à la clientèle
Servicio al cliente
Model/ Modelo/ Modèle: ID572701
1-877-SKIL-999
OR
www.skil.com
20V 1/4'' Hex Impact Driver
Clé à chocs hexagonale de 1/4 po et de 20 V
2
TABLE OF CONTENTS
General Power Tool Safety Warnings . ............................3-5
Safety Warnings for Impact Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Symbols .....................................................6-9
Get to Know Your Impact Driver ..................................10
Specications .................................................10
Operating Instructions .......................................11-15
Maintenance ...................................................16
Troubleshooting ...............................................16
Limited Warranty of SKIL Cordless Tool ............................17
WARNING
•
Some dust created by power sanding, sawing, grinding, drilling and other construction
activities contains chemicals known to the State of California to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
–
Lead from lead-based paints.
–
Crystalline silica from bricks, cement, and other masonry products.
–
Arsenic and chromium from chemically-treated lumber.
•
Your risk from these exposures varies, depending upon how often you do this type of work.
To reduce your exposure to these chemicals:
–
Work in a well-ventilated area.
–
Work with approved safety equipment, such as dust masks that are specially designed to
lter out microscopic particles.
–
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote
absorption of harmful chemicals.
3
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and specications
provided with this power tool . Failure to follow all instructions listed
below may result in electric shock, re and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE
REFERENCE.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching
outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is earthed
or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
Personal safety
Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the inuence of drugs,
alcohol or medication. A moment of inattention while operating power tools may result in
serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment
such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for
appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch or energising power tools that have the
switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a
key left attached to a rotating part of the power tool may result in personal injury.
4
Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving
parts.
If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent
and ignore tool safety principles. A careless action can cause severe injury within a fraction
of a second.
Power tool use and care
Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if
detachable, from the power tool before making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures reduce the risk of starting the
power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool
in unexpected situations.
Battery tool use and care
Recharge only with the charger specied by the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of re when used with another battery pack.
Use power tools only with specically designated battery packs. Use of any other battery
packs may create a risk of injury and re.
When battery pack is not in use, keep it away from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals together may cause burns or a
re.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or modied. Damaged or modied
batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.
5
Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or
temperature above 265 °F may cause explosion.
Follow all charging instructions and do not charge the battery pack or tool outside the
temperature range specied in the instructions. Charging improperly or at temperatures
outside the specied range may damage the battery and increase the risk of re.
Service
Have your power tool serviced by a qualied repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of battery packs should only be performed
by the manufacturer or authorized service providers.
SAFETY WARNINGS FOR IMPACT DRIVER
Hold the power tool by insulated gripping surfaces, when performing an operation
where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may
make exposed metal parts of the power tool “live” and could give the operator an electric
shock.
6
SYMBOLS
Safety Symbols
The purpose of safety symbols is to attract your attention to possible dangers. The safety
symbols and the explanations with them deserve your careful attention and understanding.
The symbol warnings do not, by themselves, eliminate any danger. The instructions and
warnings they give are no substitutes for proper accident prevention measures.
WARNING
Be sure to read and understand all safety instructions in this Owner's
Manual, including all safety alert symbols such as “DANGER,”
“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed
below may result in electric shock, re, and/or serious personal injury.
The denitions below describe the level of severity for each signal word. Please read the manual
and pay attention to these symbols.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
CAUTION, used with the safety alert symbol, indicates a hazardous
situation which, if not avoided, will result in minor or moderate injury.
Damage Prevention and Information Messages
These inform the user of important information and/or instructions that could lead to equipment
or other property damage if they are not followed. Each message is preceded by the word
“NOTICE”, as in the example below:
NOTICE: Equipment and/or property damage may result if these instructions are not followed.
WARNING
The operation of any power tools can result in foreign
objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and a full face
shield when needed. We recommend a Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always
use eye protection which is marked to comply with ANSI Z87.1.
7
SYMBOLS (CONTINUED)
IMPORTANT: Some of the following symbols may be used on your tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to operate the
tool better and more safely.
Symbol Name Designation/Explanation
V Volts Voltage (potential)
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
kg Kilograms Weight
min Minutes Time
s Seconds Time
Wh Watt-hours Battery capacity
Ah Ampere-Hours Battery capacity
Ø Diameter Size of drill bits, grinding wheels, etc.
n
0
No-load speed Rotational speed, at no load
n Rated speed Maximum attainable speed
…/min
Revolutions or
reciprocations per minute
Revolutions, strokes, surface speed,
orbits, etc. per minute
0 Off position Zero speed, zero torque...
1,2,3,…
I,II,III,
Selector settings
Speed, torque or position settings. Higher
number means greater speed
Innitely variable selector
with off
Speed is increasing from 0 setting
Arrow Action in the direction of arrow
Alternating current Type or a characteristic of current
Direct current Type or a characteristic of current
Alternating or direct current Type or a characteristic of current
Class II construction
Designates Double Insulated Construction
tools.
Earthing terminal Grounding terminal
Li-ion RBRC seal
Designates Li-ion battery recycling
program
8
Symbol Name Designation/Explanation
Ni-Cad RBRC seal
Designates Ni-Cad battery recycling
program
Read manual symbol Alerts user to read manual
Wear eye protection symbol
Always wear safety goggles or safety
glasses with side shields and a full face
shield when operating this product.
9
SYMBOLS (CERTIFICATION INFORMATION)
IMPORTANT: Some of the following symbols for certication information may be used on your
tool. Please study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and more safely.
Symbol Designation/Explanation
This symbol designates that this tool is listed by Underwriters Laboratories.
This symbol designates that this tool is recognized by Underwriters
Laboratories.
This symbol designates that this tool is listed by Underwriters
Laboratories, to United States and Canadian Standards.
This symbol designates that this tool is listed by the Canadian
Standards Association.
This symbol designates that this tool is listed by the Canadian
Standards Association, to United States and Canadian Standards.
This symbol designates that this tool is listed by the Intertek Testing
Services, to United States and Canadian Standards.
This symbol designates that this tool complies to NOM Mexican
Standards.
10
GET TO KNOW YOUR IMPACT DRIVER
20V 1/4'' Hex Impact Driver
Fig. 1
Quick-change
Collet
Variable-Speed
Trigger Switch
LED Light
Direction-of-Rotation Indicator
Direction-of-Rotation
(forward/center-lock/
reverse) Selector
Soft Grip
Removable Belt
Clip
SPECIFICATIONS
Rated voltage 20V d.c.
Collet size 1/4" Hex (power groove impact bits only)
No-load speed 0~2500 /min
Recommended working temperature 14 ~ 104°F (-10 ~ 40°C)
Recommended storage temperature 32 ~ 104°F (0 ~ 40°C)
11
OPERATING INSTRUCTIONS
WARNING
To reduce the risk of re, personal injury, and product damage due to
a short circuit, never immerse your tool, battery pack or charger in
uid or allow a
uid to
ow inside them. Corrosive or conductive
uids, such as seawater,
certain industrial chemicals, and bleach or bleach-containing products, etc, can cause a short
circuit.
WARNING
If any parts are damaged or missing, do not operate this product until
the parts are replaced. Use of this product with damaged or missing parts
could result in serious personal injury.
WARNING
Do not attempt to modify this impact driver or create accessories not
recommended for use with this impact driver. Any such alteration or
modication is misuse and could result in a hazardous condition leading to possible serious
injury.
WARNING
To prevent accidental starting that could cause serious personal
injury, always remove the battery pack from the impact driver when
assembling parts, making adjustments, cleaning, or performing maintenance.
This cordless impact driver must be used only with the battery packs and chargers
listed below:
Battery Pack
Charger
2Ah 4Ah 5Ah
SKIL BY519701 SKIL BY519601 SKIL BY519603 SKIL SC535801
NOTICE: Please refer to the battery and charger manuals for detailed operating information.
To Attach/Detach Battery Pack
(Fig. 2)
Lock the variable-speed trigger switch “OFF”
on the tool by placing the direction-of-rotation
(forward/center-lock/reverse) selector in the
center position before attaching or detaching
the battery pack.
To attach the battery pack:
Align the raised rib on the battery pack with the
grooves in the tool, and then slide the battery
pack onto the tool.
To detach the battery pack:
Depress the battery-release button, located
on the front of the battery pack, to release the
battery pack. Pull the battery pack out and
remove it from the tool.
NOTICE: When placing the battery pack onto the tool, be sure that the raised rib on battery
pack aligns with the groove inside the tool and that the latches snap into place properly.
Improper attachment of the battery pack can cause damage to internal components.
WARNING
Battery tools are always in operating condition. Therefore, the
direction-of-rotation (forward/center-lock/reverse) selector should
always be locked in the center position when the tool is not in use or carrying it at your
side.
Fig. 2
Attach
Battery-Release
Button
Detach
12
Direction-of-Rotation (Forward/Center-Lock/Reverse) Selector
WARNING
After tool use, lock the direction-of-rotation selector in the “OFF”
position (center-lock) to help prevent accidental starts and possible
injury.
Your tool is equipped with a direction-of-rotation selector, located above the variable-speed
trigger switch. This selector is used to change the direction of rotation of the bit and to lock the
variable-speed trigger in the “OFF” (center-lock) position (Fig. 3).
a. Position the direction-of-rotation selector to the far right of the tool for forward rotation.
b. Position the direction-of-rotation selector to the far left of the tool for reverse rotation.
c. Position the switch in the “OFF” (center-lock) position to help reduce the possibility of
accidental starting when not in use.
NOTICE: To prevent gear damage, always allow the impact driver to come to a complete stop
before changing the direction of rotation.
NOTICE: The impact driver will not run unless the direction-of-rotation selector is engaged
fully to the left or to the right.
Fig. 3
Forward Reverse
Center-Lock
13
Variable-Speed Trigger Switch
Your tool is equipped with a variable-speed
trigger switch. The tool can be turned "ON"
or "OFF" by depressing or releasing the vari-
able-speed trigger switch.
The variable-speed trigger switch delivers high-
er speed with increased trigger pressure and
lower speed with decreased trigger pressure
(Fig. 4).
LED Light
Your tool is equipped with an LED light, located
on the base of the tool. This provides additional
light on the surface of the work piece for
operation in lower-light areas.
The LED light will automatically turn on with a
slight squeeze on the variable-speed trigger
switch before the tool starts running, and will
turn off 8 to 12 seconds after the variable-
speed trigger switch is released.
The LED light will rapidly ash when the tool
and/or battery pack becomes overloaded or too
hot, and the internal sensors will turn the tool
off. Rest the tool for a while or place the tool
and battery pack separately under air ow for
to cool them.
The LED light will ash more slowly to indicate
that the battery is at low-battery capacity. Recharge the battery pack.
Fig. 4
Variable-Speed
Trigger Switch
Fig. 5
14
Removable Belt Clip (Fig. 6)
Your tool is equipped with a removable belt clip
that can be positioned on the left side of the
tool for convenient transport.
Install the belt clip onto the tool:
a. Remove the battery pack from the tool.
b. Align the rib of the belt clip with the threaded
hole on the base of the tool.
c. Insert the screw and securely tighten the
screw with a screwdriver.
Remove the belt clip from the tool:
d. Remove the battery pack from the tool.
e. Use a screwdriver to loosen the screw that
attaches the belt clip to the impact driver.
f. Remove the screw and the belt clip.
Install and Remove Bits
Your tool is equipped with a quick-change collet, making bit installation and removal very
easy.
Lock the variable-speed trigger switch “OFF” by placing the direction-of-rotation selector in the
center position.
To install the bit:
Pull the locking sleeve forward, insert the bit as far as it will go into the collet, and release the
locking sleeve to lock the bit. (Fig. 7)
To remove the bit:
Pull the locking sleeve forward. Pull the bit from the collet and release the sleeve.
Fig. 7
Locking Sleeve
NOTICE: Use only bits with power grooves; other bits can be used with a universal bit holder
that has power groove. Do not use bits that have a damaged shank.
WARNING
Use protective gloves when removing the bit from the tool, or rst
allow the bit to cool down. The bit may be hot after prolonged use.
Fig. 6
15
Tighten and Loosen Nuts and Bolts
Variable-speed control must be used with
caution for driving nuts and bolts with socket-
set attachments. The best technique is to start
slowly, increase speed as the nut or bolt runs
down, and then set the nut or bolt snugly by
slowing the tool to a stop. If this procedure is
not followed, the tool will have a tendency to
torque or twist in your hand when the nut or
bolt seats.
a. Install a suitable bit.
b. Apply just enough pressure to keep the bit
engaged on the screw or nut.
c. Apply minimal pressure to the variable-speed
trigger switch initially. Increase the speed
only when full control can be maintained.
NOTICE:
a. Always use the correct type and size of bit for your application.
b. When turning in a screw at/near the cross cut end or an edge of wood, pre-drill a hole in
order to avoid cracking of the wood.
c. When screw driving in hard wood, one should pre-drill a hole.
WARNING
Do not over-tighten, as the force of the impact driver can break the
fastener. Keep the impact driver at a right angle to the fastener to
avoid damaging the fastener head.
Fig. 8
16
MAINTENANCE
WARNING
To avoid serious personal injury, always remove the battery pack
from the tool when cleaning or performing any maintenance.
Service
WARNING
Preventive maintenance performed by unauthorized personnel may
result in misplacing of internal wires and components which could
cause serious hazard. We recommend that all tool service be performed by a SKIL Factory
Service Center or Authorized SKIL Service Station.
General Maintenance
WARNING
When servicing, use only identical replacement parts. Use of any
other parts could create a hazard or cause product damage.
Periodically inspect the entire product for damaged, missing, or loose parts such as screws,
nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product
until all missing or damaged parts are replaced. Please contact customer service or an
authorized service center for assistance.
Cleaning
WARNING
The tool may be cleaned most effectively with compressed dry air. Always
wear safety goggles when cleaning tools with compressed air.
Ventilation openings and switch selectors must be kept clean and free of foreign matter. Do
not attempt to clean by inserting pointed objects through openings.
WARNING
Certain cleaning agents and solvents damage plastic parts. Some of
these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,
ammonia and house hold detergents that contain ammonia.
Storage
Store the tool indoors in a place that is inaccessible to children. Keep it away from corrosive
agents.
TROUBLE SHOOTING
Problem Cause Remedy
Tool does not work. 1. Battery pack is depleted. 1. Charge the battery.
2. Tool is over-loaded. 2. Release the variable-speed trigger
switch and try again.
3. Battery pack is over-
temperature
3. Turn off the impact driver and cool
the battery pack under air
ow.
4. Battery pack is not installed
properly.
4. Conrm that the battery is locked
and secured to the tool.
5. Burned out switch. 5. Have the switch replaced by an
Authorized SKIL Service Center or
Service Station.
Bit cannot be
installed.
Bit does not t the sleeve. Use a suitable bit or adapter.
17
LIMITED WARRANTY OF SKIL CONSUMER TOOLS
5 YEAR LIMITED WARRANTY- LEGAL
Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL
consumer TOOLS will be free from defects in material or workmanship for a period of ve
years from date of purchase, if original purchaser registers the product within 30 days from
purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration
can be completed online at www.Registermyskil.com. Original purchasers should also retain
their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS
CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.
If original purchasers do not register their product timely, the foregoing limited warranty will
apply for a duration of three years for tools. All batteries and chargers will remain under the
two-year limited warranty.
Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional
or commercial purposes, the foregoing warranty will apply for a duration of ninety days,
regardless of registration.
SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited
Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall
be the repair or replacement of parts, without charge, which are defective in material or
workmanship and which have not been misused, carelessly handled, or repaired by persons
other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,
you must return the complete product, transportation prepaid, to any SKIL Factory Service
Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,
please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS
CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING
BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.
ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN
DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE
TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME
STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)
ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.
AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE
TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.
THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED
STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR
WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL
DEALER OR IMPORTER.
© Chervon North America, 1203 E. Warrenville Rd, Naperville, IL 60563.
08/18
18
TABLE DES MATIÈRES
Avertissements de sécurité généraux relatifs
aux outils électriques . .......................................19-21
Avertissements de sécurité pour la clé à chocs. .....................21
Symboles ..................................................22-25
Apprenez à connaître votre clé à chocs. ............................26
Caractéristiques techniques .....................................26
Mode d’emploi ..............................................27-31
Entretien ......................................................32
Dépannage ....................................................33
Garantie limitée de l’outil sans l SKIL ..........................34-35
AVERTISSEMENT
•
La poussière créée pendant le ponçage, le sciage, le polissage, le perçage et d’autres
activités liées à la construction peut contenir des produits chimiques reconnus par l’État
de la Californie comme étant la cause de cancers, d’anomalies congénitales et d’autres
problèmes liés aux fonctions reproductrices. Voici des exemples de ces produits chimiques :
–
Plomb provenant de peintures à base de plomb.
–
Silice cristalline provenant de la brique, du ciment ou d’autres matériaux de maçonnerie.
–
Arsenic et chrome contenus dans le bois d’œuvre traité avec des produits chimiques.
•
Les risques liés à l’exposition à ces produits varient selon le nombre de fois où vous
pratiquez ces activités. Pour réduire votre exposition à ces produits chimiques :
–
Travaillez dans un endroit bien ventilé.
–
Munissez-vous de l’équipement de sécurité approuvé tel que des masques antipoussières
conçus spécialement pour ltrer les particules microscopiques.
–
Évitez l’exposition prolongée à la poussière causée par le ponçage mécanique, le sciage, le
polissage, le perçage et d’autres activités liées à la construction. Portez un équipement de
protection et lavez à l’eau et au savon toutes les parties exposées. Les poussières pénétrant
dans votre bouche ou dans vos yeux et les poussières se déposant sur votre peau peuvent
causer l’absorption de produits chimiques dangereux.
19
AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX RELATIFS
AUX OUTILS ÉLECTRIQUES
AVERTISSEMENT
Lisez tous les avertissements et toutes les instructions,
illustrations et spécications fournis avec cet outil
électrique. Le non-respect des consignes de sécurité ci-dessous peut occasionner un choc
électrique, un incendie ou des blessures graves.
CONSERVEZ TOUS LES AVERTISSEMENTS ET TOUTES LES
INSTRUCTIONS AFIN DE POUVOIR LES CONSULTER RÉFÉRER
ULTÉRIEUREMENT.
L’expression « outil électrique » utilisée dans les avertissements correspond aux outils
électriques alimentés sur secteur (à l) ou alimentés par piles (sans l).
Mesures de sécurité dans l’aire de travail
Maintenez l’aire de travail propre et bien éclairée. Les aires de travail sombres et
encombrées sont propices aux accidents.
N’utilisez pas d’outils électriques dans un endroit présentant un risque d’explosion,
par exemple en présence de liquides, de gaz ou de poussières inammables. Les outils
électriques produisent des étincelles pouvant causer un incendie en raison de la poussière et
des fumées.
Gardez les enfants et les autres personnes à l’écart lorsque vous utilisez un outil
électrique. Une distraction peut vous faire perdre la maîtrise de l’outil.
Consignes de sécurité relatives à l’électricité
Les ches des outils électriques doivent correspondre à la prise. Ne modiez jamais la
che de quelque façon que ce soit. N’utilisez pas d’adaptateur avec les outils électriques
mis à la terre. L’utilisation de ches non modiées dans les prises compatibles réduit les
risques de choc électrique.
Évitez de toucher à des surfaces mises à la terre, par exemple, un tuyau, un radiateur,
une cuisinière ou un réfrigérateur. Le contact du corps avec une surface mise à la terre
augmente les risques de choc électrique.
N’exposez pas les outils électriques à la pluie ni à tout environnement humide.
L’inltration d’eau dans un outil électrique augmente les risques de décharge électrique.
N’utilisez pas le cordon d’alimentation de façon à l’endommager. Ne transportez jamais
un outil électrique en le tenant par son cordon, et ne tirez jamais sur le cordon pour le
débrancher. Tenez le cordon d’alimentation éloigné des sources de chaleur, de l’huile,
des objets coupants et des pièces mobiles. Les risques de choc électrique sont plus
élevés si le cordon d’alimentation est endommagé ou emmêlé.
Lorsque vous utilisez un outil électrique à l’extérieur, utilisez une rallonge conçue pour
être utilisée à l’extérieur. Ce type de rallonge réduit les risques de choc électrique.
Si vous n’avez d’autre choix que d’utiliser un outil électrique dans un endroit humide,
utilisez une alimentation protégée par un disjoncteur différentiel. L’utilisation d’un
disjoncteur différentiel réduit les risques de choc électrique.
Sécurité personnelle
Soyez vigilant, prêtez attention à ce que vous faites et usez de votre jugement lorsque
vous utilisez un outil électrique. N’utilisez pas un outil électrique lorsque vous êtes
fatigué ou sous l’effet de drogues, d’alcool ou de médicaments. Un moment d’inattention
lorsque vous utilisez des outils électriques peut occasionner des blessures graves.
20
Utilisez un équipement de protection. Portez toujours des lunettes de sécurité. Le
port d’un équipement de protection (comme un masque antipoussières, des chaussures de
protection antidérapantes, un casque de sécurité ou un dispositif de protection auriculaire),
lorsque les conditions l’exigent, réduit les risques de blessures.
Prenez des mesures an d’éviter que l’outil se mette en marche accidentellement.
Veillez à ce que l’interrupteur soit en position d’arrêt avant de connecter le produit
au courant ou au bloc-piles, de le ramasser ou de le transporter. Transporter les outils
électriques avec le doigt sur la gâchette ou brancher les outils lorsque l’interrupteur est à la
position de marche augmente les risques d’accident.
Enlevez toute clé de serrage ou clé à molette avant de mettre l’outil électrique
en marche. Une clé de réglage oubliée sur une pièce rotative de l’outil électrique peut
occasionner des blessures graves.
Ne tendez pas les bras trop loin. Gardez une posture sécuritaire et un bon équilibre
en tout temps. Cela vous permet de mieux maîtriser l’outil électrique lorsque des situations
inattendues se présentent.
Habillez-vous convenablement. Ne portez pas de vêtements amples ni de bijoux.
Gardez vos cheveux, vos vêtements et vos gants loin des pièces mobiles. Les vêtements
amples, les bijoux ou les cheveux longs risquent de se prendre dans les pièces mobiles.
Si des dispositifs sont fournis pour le branchement d’équipement de dépoussiérage
et de collecte de la poussière, veillez à ce qu’ils soient branchés et utilisés de manière
appropriée. L’emploi d’un dépoussiéreur contribue à réduire les dangers liés à la poussière.
Même si vous connaissez parfaitement ces outils parce que vous les utilisez souvent,
soyez vigilant et respectez les principes de sécurité. Il suft d’être négligent une fraction
de seconde pour se blesser gravement.
Utilisation et entretien d’un outil électrique
Ne forcez pas l’outil électrique. Utilisez l’outil électrique approprié à la tâche que vous
souhaitez accomplir. L’outil électrique adéquat vous permettra de mieux accomplir le travail
avec plus de sécurité et au rythme pour lequel il a été conçu.
N’utilisez pas l’outil électrique si l’interrupteur ne permet pas de le mettre en marche et
de l’arrêter. Tout outil électrique qui ne peut être commandé au moyen de l’interrupteur est
dangereux et doit être réparé.
Débranchez la che de la source d’alimentation ou retirez, si possible, le bloc-
piles de l’outil électrique avant de le ranger ou de procéder à un ajustement ou à un
changement d’accessoire. Ces mesures de sécurité préventives réduisent les risques de
mettre accidentellement l’outil électrique en marche.
Rangez l’outil électrique à l’arrêt hors de la portée des enfants et n’autorisez pas une
personne ne sachant pas s’en servir ou n’ayant pas lu ces instructions à l’utiliser.
Les outils électriques sont dangereux s’ils se retrouvent entre les mains d’utilisateurs qui ne
savent pas s’en servir.
Entretenez les outils électriques et les accessoires. Vériez les pièces mobiles pour
vous assurer qu’elles ne sont pas désalignées, enrayées, brisées, ou dans un état qui
pourrait nuire à leur fonctionnement. Si l’outil électrique est endommagé, faites-le réparer
avant de l’utiliser. De nombreux accidents sont provoqués par des outils électriques mal
entretenus.
Gardez vos outils tranchants affûtés et propres. Des outils de découpe aux lames affûtées
risquent moins de s’accrocher et sont plus faciles à contrôler.
Utilisez l’outil électrique, les accessoires, les mèches, etc. conformément à ces
instructions, en tenant compte des conditions de travail et de la tâche à accomplir.
L’utilisation de l’outil électrique à des ns autres que celles pour lesquelles il a été conçu
pourrait créer une situation dangereuse.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Skil ID572702 Le manuel du propriétaire
- Catégorie
- Outils électroportatifs
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Skil ID572702 Owner's manual
Documents connexes
-
Skil ID6744A-00 Le manuel du propriétaire
-
-
-
-
-
-
-
-
-
Skil PWR CORE 12™ 12V Brushless Impact Wrench Le manuel du propriétaire
