Real Fyre GR47 Le manuel du propriétaire

1

REV 0 -A - 2004290720

L-A2-458

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

This gas log set is to be installed only in a solid-fuel

burning ﬁreplace with a working ﬂue and constructed

of noncombustible material. The installation, including

provisions for combustion and ventilation air must

conform with the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, or the CSA B149.1, Natural Gas and Propane

Installation Code, and applicable local building codes.

A damper clamp, which must be permanently installed,

is included to maintain the minimum permanent vent

opening and to prevent full closure of the damper.

The chimney damper MUST be fully opened when

burning the unit. The unit is designed to burn

with yellow ﬂames; thus adequate ventilation is

absolutely necessary.

To comply with certification, listings, and building

code acceptances, and for safe operation and proper

performance of this gas log set, you must use ONLY

Peterson Real Fyre parts, decorative media, and

accessories. Use of any other controls, parts, or

accessories not designed for use with Real Fyre gas

log sets is prohibited. This will void all warranties,

certiﬁcations, listings, and building code approvals,

and may cause property damage, personal injury, or

loss of life. Peterson will not be liable for any damages

caused by this misuse.

*Note: Solid-fuels shall not be burned in a ﬁreplace

where this product is installed.

FOR INSTALLATION IN

SOLID-FUEL BURNING

FIREPLACES*

IMPORTANT: READ THESE INSTRUCTIONS

CAREFULLY BEFORE STARTING

INSTALLATION OF THE UNIT.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in the building.

• Immediately call the gas supplier

from a neighbor’s phone. Follow gas

supplier’s instructions.

• If you cannot reach the gas supplier,

call the ﬁre department.

WARNING

If the information in this manual is not

followed exactly, a fire or explosion

may result, causing property damage,

personal injury, or loss of life.

This appliance is only for use with the type

of gas indicated on the rating plate.

Installation and service must be

performed by a qualiﬁed professional

service technician, service agency, or

the gas supplier.

DESIGN CERTIFIED

to

Vented Decorative Appliance

ANSI Z21.60

CSA 2.26

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

INSTALLATION &

OWNER’S MANUAL

GR47 RUMFORD VENTED GAS LOG SETS

Burner Systems:

GR47- ** (P)A

GR47- ** -02(M)(P)

GR47- ** -17(M)(P)

**Sizes:

(18/20, 24/30)

Regulated burner system for

use w/ propane or natural gas

2

REV 0 -A - 2004290720

L-A2-458

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

Le Real Fyre système de brûleur doit être installée

seulement dans une cheminée brûlante de combustible

solide avec une conduite de cheminée fonctionnante

et être construit avec du matériel non-combustible.

L'installation, y compris des dispositions pour l'air de

combustion et de ventilation doit se conformer au code

national de gaz de carburant, la norme ANSI Z223.1/

NFPA 54, ou le CSA B149.1, code d'installation de gaz

naturel et de propane, et codes du bâtiment locaux

applicables.

Une bride plus humide est incluse pour maintenir

l’ouverture permanente minimum de passage et pour

empêcher la pleine fermeture de la lame plus humide.

L'amortisseur de cheminée DOIT être entièrement

ouvert en brûlant l'unité. L'unité est conçue pour

brûler avec les ﬂammes jaunes; ainsi à ventilation

proportionnée est absolument nécessaire.

Pour être en conformité avec la certiﬁcation, les listes et

les acceptations du code du bâtiment, ainsi que pour un

fonctionnement en toute sécurité et des performances

correctes, vous devez utiliser UNIQUEMENT les pièces,

les supports de décoration et les accessoires Peterson

Real Fyre. L'utilisation d'autres contrôles, de pièces

ou accessoires non conçu pour une utilisation avec

les systèmes de brûleurs Real Fyre est interdite. Ceci

annulera toutes les garanties, les certiﬁcations, les

annonces et les approbations du code du bâtiment, et

peut causer des dommages matériels, des blessures

ou des pertes de vie. Peterson ne sera pas responsable

des dommages causés par ce détournement.

*Note: des Plein-carburants ne seront pas brûlés

dans une cheminée où un appareil décoratif

est installé.

POUR L'INSTALLATION DANS

LE COMBUSTIBLE SOLIDE DE

BRÛLANT FIREPLACES*

Ne stockez pas ou n’employez pas l’essence

ou d’autres vapeurs et liquides inﬂammables

à proximité de ceci ou d’aucun autre appareil.

CE QUI À FAIRE SI VOUS SENTEZ LE GAZ:

• Ouvrez une fenêtre.

• N’essayez pas de n’allumer aucun appareil.

• Ne touchez aucun commutateur

électrique; n’utilisez aucun téléphone

dans le bâtiment.

• Appelez immédiatement le fournisseur

de gaz du téléphone du voisin. Suivez les

instructions du fournisseur de gaz.

• Si vous ne pouvez pas atteindre le

fournisseur de gaz, appelez le

département de feu.

AVERTISSEMENT

Si l’information en ce manuel n’est pas suivie

exactement, une incendie ou une explosion

peut résulter, entraînant des dégats

matériels, des blessures, ou la perte de la vie.

Cet appareil sert seulement avec le type de

gaz indiqué de la plaque de contrôle.

Installation et entretien doivent être effectués par

un technicien professionnel qualiﬁé de service, un

organisme de service ou le fournisseur de gaz.

CONCEPTION CERTIFIÉE

à

Vented Decorative Appliance

ANSI Z21.60

CSA 2.26

INSTALLATEUR :

Laissez ce manuel avec l'appareil.

CONSOMMATEUR:

Maintenez ce manuel pour la future référence.

IMPORTANT: LISEZ CES INSTRUCTIONS

SOIGNEUSEMENT AVANT DE

COMMENCER L'INSTALLATION DE

L'UNITÉ.

Système de brûleur réglementé

l'usage du propane ou du gaz naturel

INSTALLATION ET

MODE D'EMPLOI

GR47 RUMFORD VENTILÉ SYSTÈMES DE BRÛLEURS

Systèmes de brûleur:

GR47- ** (P)A

GR47- ** -02(M)(P)

GR47- ** -17(M)(P)

**Tailles:

(18/20, 24/30)

3

REV 0 -A - 2004290720

L-A2-458

TABLE OF CONTENTS

GETTING STARTED

IMPORTANT PRE-INSTALLATION AND FIREPLACE

SAFETY INFORMATION �� 5

FIREPLACE OPERATING SAFETY INFORMATION �� 7

SPECIFICATIONS�� 8

DAMPER CLAMP INSTRUCTIONS �� 11

GR47 BURNER PARTS LIST - MANUAL (A) SERIES ��12

GR47 BURNER PARTS LIST - 02 SERIES �� 13

GR47 BURNER PARTS LIST - 17 SERIES �� 14

INSTALLATION

INSTALLATION ��15

INSTALL BURNER ��15

INSTALL BATTERIES (if applicable) ��15

INSTALL REMOTE RECEIVER / SWITCH BOX (if

applicable) �� 16

PLACE WIRE GUARD (if applicable) �� 16

PREPARE GRATE AND CENTER �� 17

HEAT SHIELD PLACEMENT ��18

LIGHTING TEST ��18

LAVA GRANULES/COALS (optional) ��18

SAND/VERMICULITE PLACEMENT ��19

BLACK EMBERS PLACEMENT �� 19

GRATE PLACEMENT ��20

LOG SET PLACEMENT�� 22

INSTALLING/REPLACING BATTERIES (if applicable) �23

REMOTE TRANSMITTER BATTERY �� 23

RECEIVER/BURNER SYSTEM BATTERIES ��23

NOTES PAGE ��24

USE, CARE, & SERVICE

LIGHTING INSTRUCTIONS - MANUAL (A) SERIES ��25

FOR YOUR SAFETY, READ BEFORE LIGHTING ��25

LIGHTING THE PILOT ��25

LIGHTING THE BURNER ��27

SHUTTING DOWN ��27

PILOT BURNER CHECK/ADJUSTMENT ��27

LIGHTING INSTRUCTIONS - 02 SERIES ��29

FOR YOUR SAFETY, READ BEFORE LIGHTING ��29

REMOTE LIGHTING (if equipped) ��29

MANUAL LIGHTING �� 31

SHUTTING DOWN ��31

LIGHTING INSTRUCTIONS - 17 SERIES ��33

FOR YOUR SAFETY, READ BEFORE LIGHTING ��33

LIGHTING THE PILOT ��33

REMOTE LIGHTING (if equipped) ��33

MANUAL LIGHTING �� 35

SHUTTING DOWN ��37

PILOT BURNER CHECK/ADJUSTMENT ��37

REMOTE OPERATING INSTRUCTIONS - 17 SERIES �� 37

ORIENTATION ��37

FLAME HEIGHT ��37

CLEANING AND SERVICING �� 39

SYNCING THE REMOTE SYSTEM (if applicable) ��40

FLAME DESCRIPTION ��40

TROUBLESHOOTING ��41

ELECTRONIC PILOT TROUBLESHOOTING (IF

APPLICABLE) ��43

WARRANTY �� 44

4

L'INFORMATION DE SÛRETÉ IMPORTANTE DE PRÉINSTALLATION ET DE CHEMINÉE

A. FAITES ATTENTION: Sinon installé, entretenu, et utilisé correctement par ces instructions, ce produit peut causer le

dommage corporel, les dégats matériels, ou les pertes humaines sérieux.

B. AVERTISSEMENT: Quand l'installation dans une cheminée plein-carburant-brûlante, la conduite de cheminée, l'amortisseur,

et le foyer de cheminée doivent ÊTRE COMPLÈTEMENT NETTOYÉS de la suie, de la créosote, des cendres, et de la peinture

lâche, et doivent être inspectés par un décapant qualiﬁé de cheminée. Quelques cheminées plus anciennes peuvent ont besoin

de réparation avant d'installer cet appareil.

C. Le plancher du foyer doit être plat et lisse.

D. Cet appareil sert seulement avec le type de gaz indiqué de la plaque de contrôle. Cet appareil n'est pas CONVERTIBLE de

CHAMP pour l'usage avec d'autres gaz.

VÉRIFIEZ LE TYPE de GAZ (normal ou propane) : La fourniture de gaz doit être identique qu'indiquée de votre plaque de

contrôle de système de brûleur. Si la fourniture de gaz est différente, N'INSTALLEZ PAS. Contactez votre revendeur pour l'aide

immédiate.

E. LA PRESSION DE GAZ INSUFFISANTE GARDERA LE PILOTE DU FONCTIONNEMENT CORRECTEMENT (SI ÉQUIPÉ).

N'EMPLOYEZ PAS SI LA PRESSION DE GAZ EST INFÉRIEURE À LA CONDITION MINIMUM.

F. L'admission minimum gaz-fournissent la pression aux ﬁns de l'ajustement d'entrée est 5" ; colonne d'eau (w.c.) sur le gaz naturel

et le 11" ; w.c. sur le gaz de propane. La pression de gaz insufﬁsante affectera l'opération appropriée du pilote (si équipé).

N'installez pas cet appareil à gaz si la pression minimum n'est pas disponible. L'admission maximum gaz-fournissent la pression

est 10.5" ; w.c. sur le gaz naturel et le 13" ; w.c. sur le gaz de propane. La source de propane doit être réglée. (Ne branchez

pas cet appareil directement à un réservoir de gaz propane non réglementée - cela peut provoquer une explosion.) Ne

branchez pas cet appareil à une bouteille de gaz propane portable.

G. Le système sifﬂant de gaz doit être classé pour fournir la pression d'admission minimum au débit maximum (BTU/hr).

La perte de pression anormale se produira si la pipe est trop petite, ou la course est trop longue. La pipe de fourniture de gaz

doit être

1

/

2

" ; diamètre intérieur minimum. Si la ligne de gaz est plus longue que 20' ; une ligne de plus grand diamètre peut

être nécessaire. Reportez-vous aux directives NFPA 54 pour plus de détails.

H. Les estimations d'entrée montrées en Btu par heure sont pour des altitudes jusqu'à 2.000 pi. Pour des altitudes au-dessus de

2.000 pi, référez-vous au code national de gaz de carburant ou entrez en contact avec le fabricant avant d'installer ce produit.

I. Cet appareil à gaz et son clapet à gaz principal doivent être disconnected du gaz-fournissent le système sifﬂant pendant tout

vériﬁcateur de pression de ce système aux pressions d'essai au-dessus de 1/2 psig.

J. Cet appareil à gaz doit être isolé dans gaz-fournissent le système sifﬂant en fermant le robinet d'isolement d'équipement relié

au gaz-fournissent la ligne pendant tout vériﬁcateur de pression du gaz-fournissent le système sifﬂant aux pressions d'essai

égales à ou moins d'à 1/2 psig.

K. Pour installer l'appareil à gaz dans votre foyer, le foyer doit satisfaire aux exigences minimales de taille (voir le tableau

des spéciﬁcations du produit dans la section SPÉCIFICATIONS).

L. Cet appareil peut être installé dans un marché des accessoires, maison (mobile) de manière permanente située et manufacturée,

où non interdit par des codes locaux. L'installation des appareils a conçu pour la maison manufacturée (États-Unis seulement)

ou installation de caravane résidentielle doit se conformer au CAN/CSA standard Z240 MH, logement mobile, au Canada, ou à

la construction et au standard de sécurité à la maison manufacturés, intitulent 24 CFR, la partie 3280, aux Etats-Unis, ou quand

une telle norme ne s'applique pas, à ANSI/NCSBCS A225.1/NFPA 501A, installations à la maison manufacturées standard.

M. NE PAS installer ce système de brûleur dans un foyer avec une lèvre en cendres ou un renfoncement supérieur à

3

/

4

".

N. Si ce système de brûleur est installé dans un foyer avec des portes en verre et que les portes ont un cadre qui obstrue le ﬂux

d'air vers le sol du foyer, celui-ci DOIT comporter des fentes (au-dessus du sol du foyer) permettant une ventilation adéquate.

L'ouverture (avec les portes complètement ouvertes) DOIT respecter les exigences minimales de largeur et de hauteur de

la cheminée. Les portes en verre DOIVENT être complètement ouvertes lorsque le brûleur est en marche.Voir la section

SPÉCIFICATIONS pour plus de détails.

ATTENTION: L'installation et la réparation doivent être faites par un NFI certiﬁé ou tout autre installateur professionnel qualiﬁé.

Installateur: Lisez soigneusement ces instructions avant d'installer ce système de brûleur à gaz. Soyez sûr que vous comprenez

tous les mesures de sécurité et avertissements contenus en ce manuel.

5

IMPORTANT PRE-INSTALLATION AND FIREPLACE SAFETY INFORMATION

A. BE CAREFUL: If not installed, serviced, and used correctly per these instructions, this product can cause serious

personal injury, property damage, or loss of life.

B. WARNING: When installing in a solid-fuel-burning ﬁreplace, the chimney ﬂue, damper, and ﬁrebox must be thoroughly

CLEANED of soot, creosote, ashes, and loose paint, and must be inspected by a qualiﬁed chimney cleaner. Some older

ﬁreplaces may need repair prior to installing this appliance.

C. The ﬁreplace ﬂoor must be level and smooth.

D. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is NOT FIELD CONVERTIBLE

for use with other gasses.

CHECK GAS TYPE (natural or L.P.): The gas supply must be the same as stated on your burner system rating plate. If

gas supply is different, DO NOT INSTALL. Contact your dealer for immediate assistance.

E. INSUFFICIENT GAS PRESSURE WILL KEEP THE PILOT (IF EQUIPPED) FROM OPERATING PROPERLY.

DO NOT USE IF GAS PRESSURE IS LOWER THAN THE MINIMUM REQUIREMENT.

F. The minimum inlet gas-supply pressure for purposes of input adjustment is 5" water column (w.c.) on natural gas and

11" w.c. on L.P. gas. Insufﬁcient gas pressure will affect proper operation of the pilot (if equipped). Do not install this gas

appliance if minimum pressure is not available. The maximum inlet gas-supply pressure is 10.5" w.c. on natural gas and

13" w.c. on L.P. gas. The L.P. source must be regulated. (Do not connect this appliance directly to an unregulated

L.P. gas tank - this can cause an explosion.) Do not connect this appliance to a portable L.P. gas cylinder.

G. The gas piping system must be sized to provide minimum inlet pressure at the maximum ﬂow rate (BTU/hr).

Undue pressure loss will occur if the pipe is too small, or the run is too long. Gas supply pipe must be

1

/

2

" minimum

interior diameter. If the gas line is longer than 20', a larger diameter line may be necessary. Refer to the NFPA 54

guidelines for further details.

H. Input ratings shown in BTU per hour are for elevations up to 2,000 ft. For elevations above 2,000 ft., refer to the National

Fuel Gas Code or contact manufacturer before installing this product.

I. This gas appliance and its main gas valve must be disconnected from the gas-supply piping system during any pressure

testing of that system at test pressures in excess of

1

/

2

psig.

J. This gas appliance must be isolated from the gas-supply piping system by closing the equipment shutoff valve connected to

the gas-supply line during any pressure testing of the gas-supply piping system at test pressures equal to or less than

1

/

2

psig.

K. To install the gas appliance in your ﬁreplace, the ﬁreplace MUST meet the minimum size requirements (see

product speciﬁcations table in SPECIFICATIONS section).

L. This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home, where not prohibited

by local codes. Installation of appliances designed for manufactured home (U.S. only) or mobile home installation must

conform with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction

and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable, ANSI/

NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard.

M. DO NOT install this burner system in a ﬁreplace with an ash lip or recess greater than

3

/

4

".

N. If this burner system is installed in a ﬁreplace with glass doors, and the doors have a frame that obstructs airﬂow

to the ﬁreplace ﬂoor, the frame MUST have slots (above the ﬁreplace ﬂoor) that allow adequate ventilation. The

opening (with doors fully open) MUST meet the minimum ﬁreplace size front width and height requirements. The

glass doors MUST be fully open when the burner is in operation. See the SPECIFICATIONS section for details.

CAUTION: Installation and repair must be done by an NFI Certiﬁed or other qualiﬁed professional installer.

Installer: Carefully read these instructions before installing this gas burner system. Be sure you understand

all safety precautions and warnings contained in this manual.

GETTING STARTED

6

INFORMATIONS SUR LA SÉCURITÉ D'EXPLOITATION DE CHEMINÉE

A. Adultes doivent être présents lors de cet appareil au gaz est en marche. Cette unité ne doit pas être laissé sans surveillance

ou brûlure lorsque tout quelqu'un dort.

B. Gardez le domaine du clair réglé de notation de gaz et libérez des matériaux combustibles, l'essence, et d'autres vapeurs et

liquides inﬂammables.

C. Ne pas utiliser cet appareil si une partie quelconque a été submergée. Appelez immédiatement un technicien de service qualiﬁé

pour inspecter l'appareil et pour remplacer toute pièce du système de contrôle et toute commande de gaz qui a été sous l'eau.

Tentative d'opération peut entraîner un incendie ou une explosion entraînant des dommages matériels, des blessures ou des

pertes de vie.

D. Un écran de cheminée doit être en place lorsque le système brûle. Des dispositions pour un air de combustion adéquat

doivent être maintenues. Sauf si d'autres dispositions pour l'air de combustion sont prévues, l'écran aura une ouverture pour

l'introduction d'air de combustion. L'air de combustion est adéquat lorsque toutes les ﬂammes sont enroulées dans le foyer et

loin de l'écran. Lorsque vous utilisez un foyer (porte) en verre, les portes en verre DOIVENT être complètement ouvertes

lorsque le brûleur est en marche.

E. Ne retirez pas les plaques signalétiques ou les étiquettes d'avertissement. Ceux-ci sont une composante de sécurité et

d'identiﬁcation intégrante de cet appareil.

F. Assurez-vous de lire la section de nettoyage et l'entretien et la section de description de la ﬂamme.

7

FIREPLACE OPERATING SAFETY INFORMATION

A. Adults shall be present when this gas appliance is operating. This unit shall not be left burning when unattended or

while anyone is sleeping.

B. Keep the area of the gas burner system clear and free from combustible materials, gasoline, and other ﬂammable

vapors and liquids.

C. DO NOT use this appliance if any part has been underwater. Immediately call a qualiﬁed service technician to inspect

the appliance and to replace any part of the control system and any gas control that has been underwater. Attempted

operation may result in ﬁre or explosion resulting in property damage, personal injury or loss of life.

D. A ﬁreplace screen must be in place when the system is burning. Provisions for adequate combustion air must be

maintained. Unless other provisions for combustion air are provided, the screen shall have an opening(s) for introduction

of combustion air. Combustion air is adequate when all ﬂames curl into the ﬁreplace and away from the screen. When a

glass ﬁreplace enclosure (door) is used, the glass doors MUST be fully open when the burner is in operation.

E. Do not remove the rating plates or the warning tags. These are an integral safety and identiﬁcation component of this

appliance.

F. Be sure to read the CLEANING AND SERVICING and FLAME DESCRIPTION sections.

8

Real Fyre gas burner systems must be installed only in a solid-fuel burning ﬁreplace with the

minimum ﬁrebox dimensions and venting requirements met (see following tables). This appliance

is designed to burn with yellow ﬂames; adequate ventilation is absolutely necessary.

SPECIFICATIONS

Product Speciﬁcations

Speciﬁcation Value Qty.

02 burner system battery type D battery 2

Remote transmitter battery type 12V battery 1

Remote receiver battery type AA battery 4

Table 2 - Technical Data (if applicable)

Model

Minimum Fireplace Size BTU Rating

Width *

Depth ‡ Height Nat. Gas L.P. Gas

Front Rear †

GR47-18/20 34" 26" 17" 32" 75k 60k

GR47-24/30 40" 32" 17" 36" 95k 80k

Important Information Regarding Dimensions

* For 02 models, add 2" to both front and rear width.

These required widths allow for centering of the unit.

†

Rear width is at corresponding depth.

‡ If an ash lip exists, the depth requirement begins inside of the lip (see Fig. 8-1 below).

Table 1 - Product Speciﬁcations

Fireplace

side view

Max.

3

/

4

"

ASH LIP OR

RECESS UP

TO

3

/4"

(MAX)

DEPTH to be

measured as

shown (when

ash lip exists)

Fig. 8-1 Ash lip/recess detail

Fireplace Requirements

These requirements MUST be met:

Ash Lip/Recess

DO NOT install this burner system in a ﬁreplace with

an ash lip or recess greater than

3

/

4

". See Fig. 8-1.

9

SPECIFICATIONS (cont.)

Fireplace Requirements (cont.)

Glass Doors

If this burner system is installed in a ﬁreplace with glass doors, and the doors have a frame that OBSTRUCTS

AIRFLOW to the ﬁreplace ﬂoor, the frame MUST have slots (above the ﬁreplace ﬂoor) that allow adequate

ventilation. See Fig. 9-1.

Important: The opening (with doors fully open) MUST meet the minimum ﬁreplace size front width and height

requirements. See Table 1 (previous page) and Fig. 9-1.

Important: The glass doors MUST be fully open when the burner is in operation.

Fig. 9-1 Correct glass-doors frame setup, ventilation, and use (if applicable)

Fireplace front view

Fireplace ﬂoor

Frame

(above

ﬁreplace

ﬂoor)

Slots that

allow

adequate

ventilation

Glass doors must

be FULLY open.

Opening (with doors

FULLY open) MUST meet

front width and height

requirements in Table 1

(on previous page)

Fig. 9-3 Incorrect glass-doors frame setup, ventilation, and use (if applicable)

INCORRECT

USE

(DO NOT operate

your burner with

glass doors only

partially open)

10

SPECIFICATIONS (cont.)

Fig. 10-2

S

02 SERIES WIRING DIAGRAM

Fig. 10-1

Valve

Ignition

module

Wire

harness

Battery

box

Ground

wire

Pilot

assembly

Electrode

wires

Manual

switch

OR

Remote

receiver

Thermo switch

17 SERIES WIRING DIAGRAM

Valve

Thermocouple

line

Pilot

assembly

Remote receiver

(optional)

Wire

harness

11

Damper clamp

Set screw

Open

Closed

DAMPER CLAMP INSTRUCTIONS

Fig. 11-1 Damper clamp detail

Fig. 11-2 Damper open / closed

The damper clamp with hex bolt (Fig. 11-1) is provided as a

means to prevent full closure of the damper blade. The clamp is

easily attached to most damper blades with pliers or a wrench,

and must be permanently installed. The clamp is designed

to prevent accidental closure of the damper when installed

as illustrated (Fig. 11-2). Should the clamp not ﬁt, or fail to

provide the permanent vent opening listed in Table 3 below,

have a permanent stop installed, remove the damper blade,

or have the damper cut to provide the minimum permanent

opening required.

Note: The minimum chimney height from hearth to top of chimney is 15'.

Table 3 - Minimum Chimney Damper Vent Opening Requirements

Venting Requirements

THE DAMPER MUST BE COMPLETELY OPENED WHEN OPERATING THIS GAS APPLIANCE TO

ACHIEVE THE BEST VENTILATION POSSIBLE.

THESE ARE MINIMUM DAMPER OPENING SPECIFICATIONS.

Minimum permanent free opening area of chimney damper for venting (sq. in.)

For factory-built ﬁreplaces

Chimney height 18/20" 24/30"

15' 36 47

20' 29 41

30' 23 31

For masonry-built ﬁreplaces

15' 46 57

20' 43 52

30' 39 47

12

GR47 BURNER PARTS LIST - MANUAL (A) SERIES

Note: Photos not to scale

Replacement parts can be ordered

from your local Real Fyre dealer.

24/30" burner model shown

Pilot

18/20" model 24/30" model

Item Description Part No. Qty. Part No. Qty.

1.

or

Pilot assembly (natural)

Pilot assembly (propane)

PAC-1NAT

PAC-1LP

1

PAC-1NAT

PAC-1LP

1

2. Control valve (natural or propane) SV-19 1 SV-19 1

3.

or

Pressure regulator (natural)

Pressure regulator (propane)

PR-3NAT

PR-2LP

1

PR-3NAT

PR-2LP

1

4. Valve heat shield HS-51 1 HS-51 1

5. Regulator heat shield HS-39 1 HS-39 1

6. Flame diverter bracket SH-1 1 SH-1 1

7. Flex connector (w/ adapter), 1/2" O.D. x 12" CK-5-SP 1 CK-5-SP 1

8. Control knob w/ extension EH-11H 1 EH-11H 1

9. Grate SD-RUM-18/20 1 SD-RUM-24/30 1

10.

or

Sand (natural gas)

Vermiculite (propane gas)

CS-8

LF-15-3.5

1

CS-10

LF-15-7

1

11. Black embers EB-1 1 EB-1 1

12.

Hardware kit (damper clamp,

stabilizer clips w/ screws and nuts)

HK-1 1 HK-1 1

13. Damper clamp (only) DC-1 1 DC-1 1

Thermocouple

1

The log set is purchased and packaged separately;

contact your local Real Fyre dealer when ordering. Refer

to the instructions included with the log set.

7

10

11

9

13

12

2

3

4

5

6

8

13

GR47 BURNER PARTS LIST - 02 SERIES

Note: Photos not to scale

Replacement parts can be ordered

from your local Real Fyre dealer.

24/30" burner model shown

Pilot

18/20" model 24/30" model

Item Description Part No. Qty. Part No. Qty.

1.

or

Pilot assembly (natural)

Pilot assembly (propane)

PAC-6

PAC-7

1

PAC-6

PAC-7

1

2.

or

Control valve (natural)

Control valve (propane)

SV-45

SV-45P

1

SV-45

SV-45P

1

3. Control module IMP-1 1 IMP-1 1

4. Main harness assembly WH-11 1 WH-11 1

5.

or

Remote receiver box

(includes remote receiver, battery box, thermo switch, metal heat shield)

Switch box assembly *

(includes battery box, ON/OFF switch, thermo switch, metal heat shield)

AR-02-1

EPK-64

1

AR-02-1

EPK-64

1

6. Remote transmitter (only - if equipped) AT-R1-1 1 AT-R1-1 1

7. Valve heat shield HS-38 1 HS-38 1

8. Decorative heat shield HS-52 1 HS-52 1

9. Flame diverter bracket SH-1 1 SH-1 1

10. Flex connector (w/ adapter), 1/2" O.D. x 12" CK-5-SP 1 CK-5-SP 1

11. Grate SD-RUM-18/20 1 SD-RUM-24/30 1

12. Wire guard WHG-1 1 WHG-2 1

13.

or

Sand (natural gas)

Vermiculite (propane gas)

CS-8

LF-15-3.5

1

CS-10

LF-15-7

1

14. Black embers EB-1 1 EB-1 1

15.

Hardware kit (damper clamp,

stabilizer clips w/ screws and nuts)

HK-1 1 HK-1 1

16. Damper clamp (only) DC-1 1 DC-1 1

* to add a remote system to an 02M model, use RR-1A

1

The log set is purchased and packaged separately;

contact your local Real Fyre dealer when ordering. Refer

to the instructions included with the log set.

10

14

11

9

7

Heat sensor

4

8

Electrode

13

Remote transmitter and system

batteries included with burner

system (as applicable).

2

3

5

6

OR

12

15

Important: Minimum ﬁreplace size for 02 series is larger than other GR47 models (by 2" front & rear width).

16

14

GR47 BURNER PARTS LIST - 17 SERIES

4

5

Note: Photos not to scale

Replacement parts can be ordered

from your local Real Fyre dealer.

24/30" burner model shown

2

18/20" model 24/30" model

Item Description Part No. Qty. Part No. Qty.

1.

or

Pilot assembly (natural)

Pilot assembly (propane)

PAC-1NAT

PAC-1LP

1

PAC-1NAT

PAC-1LP

1

2. Control valve (natural or propane) SV-37 1 SV-37 1

3.

Pressure regulator (natural)

Pressure regulator (propane)

PR-3NAT

PR-2LP

1

PR-3NAT

PR-2LP

1

4.

Remote kit * †

(includes receiver, transmitter, batteries, plastic cover)

VR-1A 1 VR-1A 1

5. Remote transmitter (only) * AT-V1-1 1 AT-V1-1 1

6. Valve heat shield HS-51 1 HS-51 1

7. Regulator heat shield HS-39 1 HS-39 1

8.

Decorative heat shield * †

HS-53 1 HS-53 1

9. Remote receiver wire harness *

†

WH-01 1 WH-01 1

10. Flame diverter bracket SH-1 1 SH-1 1

11. Flex connector (w/ adapter), 1/2" O.D. x 12" CK-5-SP 1 CK-5-SP 1

12. Control knob w/ extension EH-11H 1 EH-11H 1

13. Grate SD-RUM-18/20 1 SD-RUM-24/30 1

14. Wire guard WHG-1 1 WHG-2 1

15.

or

Sand (natural gas)

Vermiculite (propane gas)

CS-8

LF-15-3.5

1

CS-10

LF-15-7

1

16. Black embers EB-1 1 EB-1 1

17.

Hardware kit (damper clamp,

stabilizer clips w/ screws and nuts)

HK-1 1 HK-1 1

18. Damper clamp (only) DC-1 1 DC-1 1

* if equipped

† to add a remote system to a 17M model, use VR-1A, HS-53, and WH-01

3

The log set is purchased and packaged separately;

contact your local Real Fyre dealer when ordering. Refer

to the instructions included with the log set.

11

16

13

10

8

7

6

15

1

Pilot

Thermocouple

12

9

14

18

17

15

REFER TO THE PARTS LIST WHEN FOLLOWING

INSTALLATION INSTRUCTIONS. 24/30" burner model

shown here.

INSTALL BURNER

1. MAKE SURE FIREPLACE GAS SUPPLY IS TURNED

OFF.

2. Locate the gas-supply stub inside the ﬁreplace and

remove the cap, if attached (reference Fig. 15-1).

CAUTION: When removing the cap, make sure the stub

does not turn, loosening the connection

inside the wall.

3. Attach the nut end of the ﬂex connector to the adapter

found on the valve or, if attached, on the regulator

behind the valve. Tighten securely.

4. Place the burner system in the ﬁreplace. Center the

burner from left to right in the ﬁreplace. See Fig. 15-2.

5. Be sure gas to the ﬁreplace is off. Remove the

adapter connected to the ﬂex connector. Attach the

adapter to the gas-supply stub using a pipe compound

resistant to all gasses. Tighten securely. Then attach

the open end of the ﬂex connector to the adapter.

Tighten securely (see Fig. 15-1). Ensure the pan rests

level on the ﬁreplace ﬂoor after connection. Adjust the

pan if necessary.

6. LEAK TEST: Make sure the burner valve is in the

OFF position. Turn on the ﬁreplace gas supply, and

test at all connections for leaks using the appropriate

soapy water solution. See Fig. 15-3. If bubbles appear,

a leak is present. Turn off the gas and tighten at all

connections. Repeat until no leaks are present. If a

leak persists, turn off the gas supply and contact the

local gas company or dealer. NEVER USE A FLAME

TO CHECK FOR LEAKS.

For manual and 17M models, continue to PREPARE

GRATE section.

INSTALL BATTERIES (if applicable)

At this stage the burner system and remote batteries are

to be installed. Reference the INSTALLING/REPLACING

BATTERIES section for details.

The Real Fyre burner system must be installed by a qualiﬁed professional service technician. Instructions

must be followed carefully to ensure proper performance and full beneﬁt from the burner system. Check to be

sure the burner system is designed and labeled for the type of gas (natural or propane gas) supplied to

ﬁreplace. Fireplace ﬂoor must be level, clean, and smooth (see FIREPLACE SAFETY INFORMATION section).

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts

speciﬁcally approved with this appliance may result in property damage or personal injury.

INSTALLATION

Fig. 15-2 Center burner pan in ﬁreplace

Fig. 15-1 Connect gas supply

Flex

connector

Adapter

Gas

supply

stub

(17 model

shown)

Installation continued on next page

Fig. 15-3 Perform leak test

Make sure

valve is in OFF

position.

(17 model shown)

INSTALLATION

16

INSTALLATION (cont.)

Fig. 16-2 Place wire guard (if applicable)

Installation continued on next page

Fig. 16-1 Install remote receiver / switch box

and heat shield (if applicable)

Refer to separate remote instructions (if applicable)

RECEIVER ON ITS SIDE

(w/ plastic cover and heat shield)

(Burner)

Place wire guard over wire harness

Fig. 16-3 Wire guard placement detail

Wire guard

Wire harness

17 REMOTE RECEIVER PLACEMENT:

IN FIREBOX, ON LEFT SIDE

(PLACE ONLY AS SHOWN)

4"

min.

Wire harness

Bottom

(against

wall)

INSTALL REMOTE RECEIVER / SWITCH BOX

(if applicable - 02 & 17 models)

For 02 models proceed to step 2

1. 17 Models Only: If this unit was shipped with a remote,

read and follow the separate remote instructions

(packed with remote) for connecting the remote to

the valve. Then continue to step 2.

2. Place the receiver/switch box inside the ﬁrebox.

Position so that it is:

• located at the left front of the ﬁrebox.

• on its side, with its bottom toward the left ﬁrebox

wall.

• a minimum of 4" from the burner/ﬂame.

See Fig. 16-1, A or B for details.

DO NOT place the receiver/switch box at the rear

of the ﬁrebox. Ensure that the box wire harness

remains away from the burner, valve, heat shield,

and ﬂame at all times. Coil any excess wire within

the box.

CAUTION: THE BOX WILL BE HOT DURING AND

AFTER OPERATION.

3. Decorative Heat Shield

Note: The decorative heatshield has a rear wall with

a notch in it. Face this notched end toward

the back of the ﬁreplace, and route the wire

harness through the notch.

17 Models: Ensure the remote receiver is properly

installed (with the plastic cover over it). Then place

the decorative heat shield over the remote receiver.

See Fig. 16-1, A.

02 Models: Place the decorative heat shield over

the remote receiver / switch box (see Fig. 16-1, B).

CAUTION: THE REMOTE RECEIVER / SWITCH

BOX AND DECORATIVE HEAT SHIELD

WILL BE HOT DURING AND AFTER

OPERATION.

PLACE WIRE GUARD (if applicable)

1. 02, 02M, & 17 models only: Place the wire guard

over the wire harness that is routed along the rear

of the ﬁreplace. (The wire routes from the valve

assembly to the remote receiver / switch box.) See

Fig. 16-2 and 16-3.

Note: Manual models and 17M models without a

remote system do not require this step. Proceed

to the next section.

A

B

- OR -

RECEIVER/BOX ON ITS SIDE

(w/ heat shield)

02 RECEIVER/BOX PLACEMENT:

IN FIREBOX, ON LEFT SIDE

(PLACE ONLY AS SHOWN)

4"

min.

Wire harness

Bottom

(against

wall)

17

INSTALLATION (cont.)

Fig. 17-1 Attach stabilizer clips to grate

Fig. 17-2 Position grate

(24/30" grate shown)

Fig. 17-3 Grate placement detail

Installation continued on next page

PREPARE GRATE AND CENTER

1. Locate the grate (outside of the ﬁreplace), and attach

the stabilizer clips to the 2 inner bars of the grate

using the provided screws and nuts (see Fig. 17-1

and Fig. 17-3).

The stabilizer clips should be positioned on the inner

bars and oriented as shown. Note the 1

1

/

2

" spacing

in Fig. 17-3. Tighten the clips in place.

2. Position the grate over the burner pan (in the ﬁreplace)

so that:

• the stabilizer clips ﬁt over the back edge of the

pan to lock it in position.

• the rear grate legs insert into the wire guard

cutouts (if applicable).

• the assembly is centered from left to right.

See Fig. 17-2 and Fig. 17-3.

Then remove the grate for future media placement.

(Remove grate after centering burner)

Clips ﬁt over back edge of pan

Grate legs insert into wire guard cutouts

(if applicable)

(Top View)

(Side View)

Legs insert into

wire guard

(if applicable)

Spacing: 1

1

/

2

"

Clips ﬁt

over burner

Attach here

18

HEAT SHIELD PLACEMENT

TO PREVENT DAMAGE AND FAILURE:

IT IS CRITICAL THAT THE HEAT SHIELD(S) BE PLACED

CORRECTLY OVER THE REGULATOR AND/OR VALVE

PRIOR TO OPERATION.

TO PREVENT OVERHEATING:

Place the valve heat shield over the valve as shown in the

applicable image of Fig. 18-1. It should rest ﬂat above the valve.

For manual and 17 models, place the regulator heat shield

as shown in the applicable image of Fig. 18-1. It should rest

ﬂat above the regulator.

Keep the area above and below the heat shield(s) clear

of decorative media or any other objects at all times.

DO NOT remove the heat shield(s).

Important: Ensure any lines/tubes/wires from the valve

do not interfere with heat shield placement.

LIGHTING TEST

Prior to proceeding with installation, perform a lighting test

(see lighting instructions for lighting your burner). Allow the

unit to completely cool after testing.

LAVA GRANULES/COALS (optional)

Optional lava granules and lava coals are available for

decorative purposes. Contact your dealer for ordering

information.

If purchased, follow the steps below.

1. Spread the lava granules on the ﬂoor of the ﬁreplace,

around the front and sides of the burner system (see

Fig. 18-2).

2. Repeat this process for the lava coals (on top of the

already placed lava granules).

Note: DO NOT place any lava media on the burner

system, behind it, on or within the heat shield, or

under a knob if one exists at the front of the valve

(see Fig. 18-3).

For models with a receiver/switch box, the lava media

may be placed around the box. Leave the front of the

receiver/switch box clear for control access.

INSTALLATION (cont.)

IMPORTANT

For all valves, the air MUST be purged from the gas line

before the pilot will light and burn properly. The time needed

to purge will depend on the length of the gas line to the

unit and the amount of time since the unit or gas line was

last used. It may take several minutes before all the air is

purged and the pilot will light and burn properly. Reference

the LIGHTING INSTRUCTIONS section in this manual.

Installation continued on next page

Fig. 18-2 Place lava media (if purchased)

Fig. 18-3 Proper lava media placement

Keep clear

(17 model shown)

Fig. 18-1 Place heat shield(s)

Heat shield(s) MUST:

• be placed over regulator and/or valve

(DO NOT remove)

• rest ﬂat

• be kept clear of all media and objects

Manual and 17 Models

02 Model

2 heat

shields

19

SAND/VERMICULITE PLACEMENT

The sand/vermiculite supplied with the unit is specially

selected for use with either natural or propane gas. It

maximizes ﬂame distribution and provides a cleaner

burning ﬂame.

CAUTION: Use only sand for natural gas burners and

vermiculite for propane gas burners.

1. Fill the burner pan completely with the sand/

vermiculite (see Fig. 19-1). Avoid spilling the sand/

vermiculite on the pilot assembly. DO NOT place

sand/vermiculite on any other parts of the burner,

valve, or heat shield.

2. Slope the sand/vermiculite at the same angle as

the burner pan. This is important to ensure quiet

lighting and even ﬂame distribution. See Fig. 19-2.

BLACK EMBERS PLACEMENT

Spread the black embers lightly and evenly over the entire

surface of the sand/vermiculite as shown in Fig. 19-3.

Break up any clumps that may have developed during

shipment. Completely cover the sand/vermiculite. DO

NOT pack the embers down.

KEEP LAVA GRANULES/COALS, SAND/

VERMICULITE, EMBERS, AND ALL FOREIGN

OBJECTS AWAY FROM THE PILOT ASSEMBLY,

VALVE ASSEMBLY, AND HEAT SHIELD(S)

DURING MEDIA PLACEMENT AND AT ALL TIMES.

SEE FIG. 19-4.

INSTALLATION (cont.)

Installation continued on next page

Fig. 19-3 Place black embers

Fig. 19-4 Keep pilot, valve, & shield(s) clear

Place embers as shown

Fig. 19-1 Place sand/vermiculite

Fig. 19-2 Sand/vermiculite detail

Fill pan (only) with

sand / vermiculite

& slope with pan.

(17 model shown)

KEEP CLEAR

OF ALL MEDIA

20

GRATE PLACEMENT

1. Place the grate over the burner pan so that:

• the stabilizer clips ﬁt over the back edge of the

pan to lock it in position.

• the rear grate legs insert into the wire guard

cutouts (if applicable).

See Fig. 20-1.

2. Place a second layer of embers lightly and evenly

over the burner and grate area. Be sure to cover the

grate bars/ﬁngers as shown. See Fig. 20-1.

Break up any clumps that may have developed during

shipment. Completely cover the area as shown. DO

NOT pack the embers down.

Store unused embers for later use/replacement.

INSTALLATION (cont.)

Fig. 20-1 Place grate

Installation continued on next page

Fig. 20-2 Place additional black embers

Cover entire area with second layer of embers

La page charge ...

Real Fyre GR47 Le manuel du propriétaire

Ce manuel convient également à

Real Fyre GR47 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents