Powermate PWFTA17322 Manuel utilisateur

Look Inside for:

Page

Safety Definitions 1

Important Safety Information 2-4

Safety Decals 5

Specifications 6

Features 6

Assembly 7-8

Engine Preparation 9-10

Operation 11-13

Slope Guide 14

Maintenance 15-20

Technical Service 20

Troubleshooting 21

Warranty 22

09/24/2018 Printed in China A203876

Operator’s Manual

FIELD TRIMMER

173cc, 4 Cycle

IMPORTANT:

Thank you for purchasing this Powermate® Field Trimmer.

This manual provides complete instructions for safely operating and maintaining your Trimmer. Read and save these

instructions. Refer to this manual each time before using your Trimmer.

Record the following for future reference:

Mfg. Date Code: ______________________

Date of Purchase: Attach a copy of your sales receipt.

Consumer Toll Free Number: 1-800-737-2112

Refer to the website for electronic manual and parts book.

www.powermateoutdoor.com

KEEP THIS MANUAL FOR FUTURE REFERENCE

MODEL Nos. PWFTA17322

If you have a question or problem...

CALL TOLL FREE: 1-800-737-2112

WARNING

This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and

birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

WARNING

CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust containing lead. Wash hands after use. Keep

out of reach of children.

EN - 1

Oil Fill Location

Do Not Overfill

Gasoline Fill Location

Start Unit Stop Unit

Engine Stop

PUSH TO PRIME

Push primer 3 times before starting a

cold engine. Prime a warm engine only

as required.

This symbol indicates a potential personal injury

hazard. It means:

Attention! Be alert! Your

safety is involved!

Wear eye protection complying with ANSI

Z87.1.

Read operator’s manual before operating this

machine. Failure to follow directions could

result in serious injury.

Disconnect spark plug wire when not in use

or before servicing, cleaning, or performing

maintenance on the unit.

Thrown objects. Remove all rocks, stones,

and foreign objects which could be thrown by

machine.

Engine exhaust contains carbon monoxide,

an odorless and deadly gas. NEVER run unit

indoors or in a poorly ventilated area.

Keep bystanders at a safe distance (15m /50

ft). NEVER use if children are present.

Do NOT touch hot muffler or cylinder. These

parts are extremely hot from operation and

may remain hot for a short time

after operation.

Do NOT trim up and down slopes. Trim

across slopes.

To reduce risk of fire, clean spilled gas and

oil and keep unit free from debris. Gasoline is

extremely flammable. Allow machine to cool a

minimum of 2 minutes before refueling.

Rotating parts can cause serious injury. Keep

hands and feet away.

Safety Definitions

• Save these instructions

Safety Warning Symbols

Control and Operating Symbols

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor/moderate injury.

Indicates a situation which may result in equipment / property damage or may relate to

general safety messages.

The following symbols are used on the product and in this manual to alert the operator of potential safety hazards. Read

them carefully, and understand their meaning.

Safety Alert Symbols

The following symbols may relate to safety and may be found on your trimmer. Carefully read and understand their meaning.

Important Safety Information

NOTICE

15m/50ft

EN - 2

Important Safety Information

• Save all instructions

RESPONSIBILITY OF THE OWNER

1. Carefully read and follow these safety instructions. Failure to do so can result in serious injury.

2. Know your product. Read and understand this manual before use. Compare the illustrations to unit. Learn location

and function of all controls. Thoroughly understanding the unit before use will result in the best performance and safety.

3. Follow all instructions when assembling the unit. If the unit was purchased in assembled condition, the operator

must check the unit carefully to make sure it was assembled according to the instructions in the manual before use.

4. Regularly inspect the trimmer. Make sure parts are not bent, damaged, or loose.

5 Use this equipment for its intended purpose only.

6. Operate the unit only with guards, shields, and other safety items in place and working correctly.

7. Service the unit only with authorized or approved replacement parts.

8. Complete all unit maintenance and adjustments according to the instructions in this manual.

To prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug

wire and put wire where it cannot contact the spark plug.

PREPARATION SAFETY

• Read, understand, and follow all instructions on this machine and in this manual. Be thoroughly familiar with the

controls and the proper use of the trimmer before starting. Know how to stop the engine quickly.

• Familiarize yourself with all the safety and operating decals on this equipment.

• Thoroughly inspect the area where the trimmer is to be used and remove all foreign objects. Your equipment can

propel small objects at high speed causing personal injury or property damage. Stay away from breakable objects,

such as house windows, auto glass, greenhouses, etc.

• Verify that the control lever is working properly. Make sure that the cable is free and that the control lever is not damaged.

• Check that all nuts and bolts are tight and equipment is in good condition. Check mounting hardware on trimmer head

every time you change trimmer line and prior to each use.

OPERATION SAFETY

• Never allow children or young teenagers to operate the trimmer.

WARNING

• Keep area of operation clear of all bystanders, particularly small children and pets.

• Only allow responsible individuals, who are familiar with the instructions, to operate the trimmer.

• Do not operate the trimmer while under the influence of alcohol, drugs, or other medication which can cause

drowsiness or affect your ability to operate this machine safely.

• Do not use this machine if you are mentally or physically unable to operate the machine safely.

• Always wear ANSI compliant safety goggles or safety glasses with side shields when operating trimmer to protect your

eyes from foreign objects, which can be thrown from the unit.

• Wear appropriate clothing such as a long sleeved shirt or jacket. Also wear long trousers or slacks. Do NOT wear

shorts. Do NOT wear loose clothing, which could get caught in this equipment.

• Always wear work gloves and sturdy footwear such as leather work shoes or short boots. These will protect ankles

and shins from small sticks, splinters, and other flying debris, and improve traction.

• It is advisable to wear protective headgear to protect against being struck by small flying particles, or being struck by

low hanging branches, twigs, or other objects, which may be unnoticed to the operator.

WARNING

EN - 3

Important Safety Information (Continued)

• Save all instructions

WARNING

• Do not put hands or feet near or under rotating parts.

• When crossing gravel drives, walks, or roads, stop the unit and wait for the trimmer lines to stop. Exercise extreme

caution. Stay alert for hidden hazards or traffic.

• Exercise caution to avoid slipping or falling. Never operate trimmer in wet grass. Always be sure of your footing;

keep a firm hold on the handle and walk; never run.

• Look behind and use care when backing.

• Never operate the trimmer without good visibility or light.

DANGER

• Do not run the engine indoors or inside a closed area. The exhaust fumes are dangerous, containing CARBON

MONOXIDE, an ODORLESS AND DEADLY GAS.

• If the trimmer should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and prevent it from

touching the spark plug. Check immediately for the cause. Vibration is generally a warning of trouble.

• Watch for holes, ruts, bumps, or other rough ground. Tall grass can hide obstacles.

WARNING

• Frequently clean debris and grass build up from the recoil starter cover holes, under the deck in the trimming

head area, and around the muffler. Using the unit with excessive debris can risk fire. Always use extreme caution when

using the trimmer during dry conditions.

• Do not trim excessively steep slopes (maximum 15 degrees). See the “Slope Guide” in the back of this manual to

check a slope.

• Always trim across the face of slope; never up and down. Exercise extreme caution when changing direction

on slopes. If you are uneasy on a slope, do NOT trim it.

• Do NOT trim near drop-offs, ditches, or embankments. The operator could lose footing or balance.

FUEL SAFETY

WARNING

• Gasoline is extremely flammable, and gasoline vapors can explode if ignited. Handle with Care.

• Use an approved container.

• Check fuel supply before each use, allowing space for expansion as the heat of the engine and/or sun can

cause fuel to expand.

• Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.

• Do not smoke while refueling.

• After refueling, replace fuel tank cap securely and wipe up spilled fuel.

• Never store fuel or trimmer with fuel in the tank inside a building where fumes may reach an open flame.

Important Safety Information

EN - 4

Important Safety Information (Continued)

• Save all instructions

STORAGE SAFETY

• Always refer to the owner’s manual instructions for important details if the trimmer is to be stored for an

extended period.

• Never store the trimmer with fuel in the fuel tank inside a building where ignition sources are present such as

water heaters, space heaters, clothes dryers, etc.

• To reduce fire hazard, keep trimmer free of grass, leaves, or other debris build-up.

• Allow the engine to cool before storing in any enclosure.

REPAIR, MAINTENANCE, AND ADJUSTMENT SAFETY

• After striking a foreign object, stop the engine. Remove the wire from the spark plug and keep the wire away

from the plug to prevent accidental starting. Thoroughly inspect the trimmer for any damage. If damaged, have

the equipment repaired by a trained technician before restarting and operating.

WARNING

• Stop the engine before cleaning, repairing, or inspecting the unit. Make sure all moving parts have stopped. Let

the engine cool, disconnect the spark plug wire and move it away from the spark plug.

• Never attempt to make any adjustments while the engine is running except when specifically recommended by the

manufacturer.

• Keep the trimmer in safe working condition. Check all fasteners at frequent intervals for proper tightness.

• When servicing or repairing the trimmer, do not tip the machine over or up unless specifically instructed to do

so in this Manual. Service and repair procedures can be done with the trimmer in an upright position. Some

procedures will be easier if the machine is lifted on a raised platform or working surface.

• Use only original equipment or authorized replacement parts.

• Never tamper with safety devices. Check their proper operation regularly.

• Do not change the engine governor setting or over-speed engine.

• Clean and replace safety and instruction decals as necessary.

• To guard against engine over-heating, always have engine debris filter mounted and clean.

CHILDREN SAFETY

WARNING

• Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to

the trimmer and the trimming activity.

• Keep children out of the trimming area and under the watchful care of a responsible adult.

• Never assume that children will remain where you last saw them.

• Be alert and turn trimmer off if children enter the area.

• Before and while moving backwards, look behind and down for small children.

• Never allow children to operate the trimmer.

• Use extra care when operating blind corners, shrubs, trees, or other objects that may obscure vision.

Important Safety Information

EN - 5

Safety Decals

• Save all instructions

This field trimmer has been designed and manufactured to

provide you with the safety and reliability you would expect

from an industry leader in outdoor power equipment

manufacturing.

Although reading this manual and the safety instructions it

contains will provide you with the necessary basic knowledge

to operated this equipment safely and effectively, we have

placed several safety labels on the field trimmer to remind you

of this important information while you are operating the unit.

These important safety labels are illustrated below, and are

shown here to help familiarize you with the location and content

to the safety messages you will see as you perform normal

trimming operations. Please review these labels now. If you

have any questions regarding their meaning or how to comply

with these instructions, reread the complete safety instruction

text on the preceding pages, or contact your local dealer.

Should any of the safety labels become unreadable because

of being worn, faded, or otherwise damaged during the use of

your field trimmer, please contact your local authorized dealer

to order replacement label.

The safety labels are easily applied, and will act as a constant

visual reminder to you and others who may use the equipment.

Following the safety instructions is necessary for safe, effective

operation of your field trimmer.

See “Safety Definitions” section of this manual for

explanations of the safety symbols.

EN - 6

Specifications

• Save all instructions

1. Control Lever - Release to stop the engine.

2. Recoil Starter Handle - The engine is equipped with an

easy pull recoil starter.

3. Recoil Starter Cover - Covers recoil starter mechanism.

Holes allow air intake to cooling system.

4. Spark Plug/Spark Plug Wire - Provides spark to ignite

air/fuel mixture. The spark plug wire must be moved

away from the spark plug when servicing the unit.

5. Muffler - Location of engine exhaust.

6. Trimmer Guard - Protects the operator from thrown

debris. Blade mounted on guard will automatically cut

trimmer line to correct length if line is too long.

7. Trimmer Line - Rotating cutting element of trimmer.

8. Trimmer Head - Rotates the trimmer lines.

9. Primer Button - Injects fuel directly into the carburetor

for faster starts.

10. Air Filter - Removes debris and contaminates from

intake air, allowing engine to run smoothly with low

exhaust.

11. Pivot Handle - Allows the trimmer head to be pivoted left,

centered or right.

12. Trimmer Line Storage - Carries additional pieces of

replacement line.

13. Trimmer Line Cut Guide - Aid to cut line to correct length.

14. Trimmer Head Height Adjustment - Allows trimmer head

to be adjusted vertically.

Features

UNIT

Unit Weight............................77 lb. (35 kg)

Cutting Swath....................... 22 in. (599 mm)

Cutting Line Diameter. . . . . . . . . . . . . . . . . 0.155 in. (4 mm)

Wheel Diameter ..................... 14 in. (356 mm)

Cutting Height................ Adjustable, 2 in. (51mm),

3 in. (76mm), 4 in. ( 102mm)

Gasoline Type .....Regular Unleaded – 87 Octane (min.)

Gasoline Capacity ..................... 1.4 qt. (1.3 L)

Oil Type (API SG-SL) . . . . . .10W-30 is recommended for all

service temperatures. See page 8 for additional information.

Oil Capacity .........................17 oz. (500 ml)

Spark Plug Model...................... Torch K6RTC

Spark Plug Gap ............... 0.030-0.037 in. (0.8-0.9

mm)

ENGINE

Type ................................4 Stroke, OHV

Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 cc

Torque Rating .....6.27 ft/lbs gross torque per SAE J1940

Bore Diam. x Stroke.........2.75 x 1.77 in. (70 x 45 mm)

Intake Valve Clearance . . . . 0.003-0.005 in. (0.08-0.12 mm)

Exhaust Valve Clearance . . . 0.006-0.008 in. (0.15-0.20 mm)

Full Throttle RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000

Figure 1

3

4

5

6

7

14

8

9

12

10

13

1

11

2

EN - 7

Read and follow the assembly instructions. Do not discard

any parts or materials until the unit is assembled.

References to the right or left side of the trimmer are from

the viewpoint of the operator’s position behind the trimmer.

Do not operate trimmer if it is damaged or not completely

and correctly assembled.

Before doing any assembly or maintenance to the unit,

remove the wire from the spark plug. The following compo-

nents will be found in the carton. Quantities shown in ( ).

Assembly

• Save all instructions

If you need assistance or find any parts missing, CALL

TOLL FREE: 1-800-737-2112.

Figure 2

Figure 3

Assemble the Handle

NOTE: Refer to Figure 2 when following the steps below

1. Attach upper handle assembly to lower handle by aligning

bolt holes and inserting provided handle bolts through

each side and assembling plastic wing nut.

Assemble the Control Cable to the Control Lever

NOTE: Refer to Figure 3 when following the steps below

After the handle has been assembled, install the control

cable as follows:

1. Insert z-hook into hole in the control lever

(insert from inside to outside).

2. Clip retainer into hole in handle.

3. Secure control cable to lower handle with cable tie

as desired.

4. Install Rope Guide through horizontal hole in right side

of handle. (Figure 2) Position guide so retaining loop is

upward. Secure with nut using 11 mm wrench.

5. To attach the recoil starter handle to the rope guide,

engage control lever, pull rope, twist the rope through the

rope guide mounted on the right side of the handle.

Included Parts in the Carton QTY

1 Operator Manual 1

2 Engine Manual 1

3

Start Guide

1

4 Wing Nuts 2

5 Handle Bolts 2

6 Shoulder Bolt 2

7 Steel Spacer 2

8 Wheel 2

9 Upper Handle 1

10

Trimmer assembly

1

11 Set of 0.155in. (4mm) Trimmer Line 2

12 Cable Ties 1

13 Container of Engine Oil 1

14 Rope Guide including nut 1

WARNING

Handle

Recoil Start

Handle

Rope Guide

Wing Nut

Wheel

Handle

Bolt

Shoulder

Bolt

Steel

Spacer

Z-hook

Control Lever

Clip retainer

Control cable

EN - 8

Assemble the Wheel

NOTE: Refer to Figure 2 when following the steps below

1. Place the unit on a level surface.

2. Assemble wheels using Spacer and Shoulder Bolt.

3. Tighten securely to 25 ft. lbs. (34 N.m) torque.

Assembly (Continued)

• Save all instructions

If you need assistance or find any parts missing, CALL

TOLL FREE: 1-800-737-2112.

Figure 4

Figure 8

Assemble the Flexible Shield

Assemble the Pivot Handle

Final Assembly

NOTE: Refer to Figure 4 when following the steps below

1. Align rear hole of exible shield with threaded stud at the

base of the deector shroud.

2. Assemble with ange nut.

WARNING

Do not operate trimmer unless all shields are fully installed.

Flange

Nut

1. Cut the black cable tie securing the handle . (Figure 5)

2. Remove the screw and nut from the Index plate.

3. Rotate the Index plate until the bolt hole aligns with the

lower handle hole. (Figure 6 ) Insert screw and nut and

tighten both upper and lower attachment screws securely.

4. Remove the Pivot Screw, Spring and Nut from the lower

end of the Pivot Handle.

5. Position the Pivot Handle so the pivot hole aligns with the

forward hole of the Index plate. (Figure 6 )

6. Install the Pivot screw and spring from the inside. Install

the Locknut from the outside. (Figure 7) Tighten the nut

only until you see one or two threads extending through

the nut. (Figure 8)

1. Assemble the clear Trimmer Line Storage tube to the

retaining clips on the left side handle.

2. Reinstall spark plug wire.

Cable

Tie

Screw

Nut

Figure 5

Index

Plate

Forward Hole of

Index Plate

Screw &

Nut

Figure 6

Nut

Spring

Sc

rew

Forward

Figure 7

EN - 9

NOTICE

Engine shipped without oil. Failure to add oil will result in

serious engine damage.

A bottle of engine oil is included with your Trimmer. Refer to

Figure 9 for alternative oil types to use at different tempera-

tures. Always use a high quality detergent oil classified “For

Service, SG, SH, SJ” or higher. Do not use special additives.

Always use recommended oil type. Using dirty oil or incorrect

oil type such as 2-stroke engine oil will shorten engine life.

HOW TO CHECK OIL LEVEL AND FILL TO PROPER LEVEL

WARNING

Before checking oil, make sure engine is off, and spark

plug wire has been disconnected from spark plug.

1. Place trimmer on a level surface.

2. Remove Dipstick and wipe clean with cloth. Refer to

Figure 10 for location of Dipstick.

3. Replace Dipstick and do NOT screw it. Remove and

check oil level.

4. When oil level is full, the oil will be at upper limit on dip

stick. If oil level is near or below the lower limit, oil must

be added. (See Figure 10)

5. Add oil slowly until the oil level reaches the upper limit of

the dipstick. Use a funnel or nozzle to reduce spillage.

Frequently check oil level while filling.

DO NOT OVERFILL. DO NOT UNDERFILL. Running

engine at improper oil level will seriously damage engine.

6. Replace and tighten dipstick.

7. Clean up any spilled oil.

Engine Preparation

• Save all instructions

Engine Oil

A

Figure 10

Figure 9

SAE

TEMP

100° F

40° C

-20

-20-30 -10

0

20

2010

40

60 80

30

Ambient Service Temperature

SAE 10W-30

SAE 30

NOTICE

Upper Limit

Lower Limit

EN - 10

WARNING

• Gasoline is extremely ammable and vapors can

explode if ignited. Handle with care.

Use fresh, clean, regular-unleaded gasoline with a

minimum of 87 Octane. Do NOT use leaded gasoline,

gasohol, methanol, or diesel fuel. Do NOT mix oil with

gasoline. Do NOT allow gasoline to become contaminated

with dust, water, or debris.

Using incorrect fuel type or contaminated fuel will cause

serious engine damage.

NOTE: Fuel tank capacity is approximately 1.4 qt. US (1.3 L).

HOW TO FILL ENGINE WITH FUEL

WARNING

• Turn engine off and let engine cool for several minutes

before removing the fuel cap or adding fuel.

• Never fill fuel tank indoors.

• Do not smoke while adding fuel.

1. Clean surface around fuel tank cap to prevent

contaminations. Refer to Figure 11 for location of fuel cap.

2. Loosen fuel cap slowly to remove.

3. Pour fuel into the tank. Use care to avoid spillage.

WARNING

Do NOT OVERFILL fuel. Allow space for the fuel to expand

due to heat from engine and/or sun.

4. Before replacing the fuel cap, inspect and clean the fuel

cap seal.

5. Replace the fuel cap and securely hand-tighten.

6. Clean up any spilled fuel.

Fuel

B

Engine Preparation (Continued)

• Save all instructions

Fuel Tank Cap

Figure 11

Oil Fill Cap/Dipstick

NOTICE

EN - 11

WARNING

Debris thrown from Trimmer can cause severe eye

damage. Always wear ANSI compliant safety glasses

or eye shields when operating trimmer. If you wear

eyeglasses, put an OSHA certified Wide Vision Safety

Mask over your eyeglasses.

Before starting Trimmer, clean debris from holes in the recoil

starter cover.

1. Review ALL steps in the “BEFORE STARTING THE

ENGINE” section.

2. Push the Primer Bulb 3 times, waiting 2 seconds

between each push. (See Figure 12)

NOTE: Prime only as required when re-starting a warm

engine.

WARNING

Before starting engine, read operator’s manual. Become

familiar with location and function of all controls. Know how

to stop the engine quickly.

Before attempting to start the engine, review the

following steps:

1. Unit has been assembled according to all

assembly instructions.

2. Unit has been inspected for any damaged or

missing components.

3. No parts are remaining in the carton.

4. Engine oil is at proper level.

5. Fresh, clean, regular-unleaded gasoline has been

added to fuel tank.

6. Spark plug wire is connected to spark plug.

7. Trimmer has been moved to desired location.

8. Trimmer is on level surface.

Operation

• Save all instructions

Before Starting the Engine

A

How to Start the Engine

B

WARNING

Keep all bystanders, especially CHILDREN, away

during operation.

IMPORTANT: This unit’s engine exhaust system is equipped

with a spark-arresting muffler. Tampering with or removing

the spark-arrestor violates section 4442 of the California

Public Resources Code as well as other applicable state

and federal law.

DANGER

Never run engine indoors or in a poorly ventilated area.

Engine exhaust contains Carbon Monoxide, an ODORLESS

and DEADLY gas.

Figure 12

Primer

Button

NOTICE

EN - 12

3. Firmly grip the Trimmer handle with your left hand,

engaging engine control lever. (See Figure 13)

4. Firmly grip the Recoil Starter Handle with your right hand.

(See Figure 13)

5. Pull the recoil starter slowly, until you feel tension in the

starter rope. Then quickly pull the recoil starter handle to

start engine. DO NOT allow the starter rope to snap back.

Let the starter rope slowly rewind as you hold the recoil

starter handle.

6. If engine fails to start after three pulls, push the primer

button two times and again pull the recoil starter handle.

7. If engine fails to start after 5 or 6 more tries, see the

instructions in the “Troubleshooting Chart”.

WARNING

Keep hands, feet, hair, and loose clothing away from any

moving parts. Avoid touching muffler and surrounding

areas. Temperatures can exceed 150° F. Keep all safety

devices and shields in place.

Operation (Continued)

• Save all instructions

Figure 13

Recoil Starter

Handle

How to Start the Engine

B

How to Stop the Engine

C

1. Release the control lever.

CAUTION

Trimmer line will continue to rotate for several seconds after releasing the control lever. Use Caution.

WARNING

Debris such as sticks, gravel, and rocks can be thrown with

sufcient force to cause personal injury or property damage.

• Frequently clean debris and grass build up from the

recoil starter cover holes, under the deck in the trimming

head area, and around the mufer. Using the unit with

excessive debris can risk re. Always use extreme

caution when using the trimmer during dry conditions.

• If the trimmer lines become too short, it will take longer

to complete this job. If the trimmer lines are worn to less

than half their original length, change to a new trimmer

line. See “How to Replace the Trimmer Line” in the

Maintenance section.

• Do not trim on excessively steep slopes. See Slope

Guide. If a slope is difcult to stand on, do not trim it. Do

not trim on slopes when the ground is slippery or wet.

Trim across the face of a slope, not up and down.

• Trimmer head contact to concrete, asphalt and harder

surfaces may create premature wear.

• For best results and longer lasting line, soak the trimmer

line in a pail of water for 24 hours prior to use. A moist

line will be more exible than a dry, brittle line.

• Let the ends of the trimming line do the cutting. This is

easily done by moving slowly through very thick or heavy

weeds.

Trimming Tips

D

EN - 13

Operation (Continued)

• Save all instructions

The trimmer head can be adjusted vertically to three differ-

ent positions. Higher positions are useful when trimming tall

grass or in conditions where frequent objects (rocks, small

limbs) are on the ground. Lower positons will provide a

more nished appearance

The engine must be off and the trimmer head not moving

prior to adjustment.

To adjust the Trimmer Head height:

• Depress the two index buttons on each side of the

trimmer head.

• Raise or lower the trimmer head. It may be necessary to

remove wrapped grass or vines from the vertical index

tube prior to adjustment. If the head will not disengage,

slightly rotate the head while depressing the index

buttons.

• When repositioned to the desired height, release the

index buttons and assure the trimmer head is locked into

the new position.

The trimmer head can be pivoted horizontally to a left,

centered or right position. Offsetting the trimmer head allow

easier trimming under fences and around post or trees.

The trimmer head can be pivoted even when the engine is

running. It is not necessary to stop the engine.

Assure no person, animal or objects are close to the trim-

mer head prior to pivoting the head.

To pivot the trimmer head:

• With the operator’s left hand rmly on the handle, grip the

pivot lever using the operator’s right hand.

• Move the lever to the left to disengage the locking

pin and rotate the lever up or down to the desired

position.

• Release the pivot lever which allows the locking pin

to re-engage.

Adjusting the Height of the Trimmer Head

E

Pivoting the Trimmer Head

F

WARNING

EN - 14

SLOPE GUIDE

SIGHT AND HOLD THIS GUIDE LEVEL WITH A VERTICAL TREE, A

CORNER OF A STRUCTURE, A POWER LINE POLE, OR A FENCE.

Operate a trimmer across the face of slopes, never up or down slopes.

Use this guide and do not trim on a slope greater than 15 degrees.

A 10-degree slope is a hill that increases in height at approximately 1.7 feet in

10 feet.

A 15-degree slope is a hill that increases in height at approximately 2.5 feet in

10 feet.

WARNING!

Use extreme care at all times and avoid sudden turns or maneuvers.

Follow other instructions in this manual for safety in trimming on slopes.

Operate a trimmer across the face of slopes, never up or down slopes. Use

extra care when operating on or near slopes and obstructions.

19

F-050204L

15 Degrees

10 Degrees

Operate a trimmer across the face of

slopes, never up or down slopes.

FOLD ALONG DOTTED LINE

15 DEGREES

EN - 15

PERIODIC MAINTENANCE SCHEDULE TABLE

CAUTION

IMPORTANT NOTES about Maintenance schedule

1. Change Trimmer Lines when they are half original length.

2. Frequently clean grass from:

a. Holes in recoil starter cover

b. Under deck in the trimmer head area

c. Around mufer

3. Re-check fastener tightness after the rst 2 hours of

initial use.

4. Clean air lter every 10 hours. Clean more often if

operating under dusty conditions.

5. Change engine oil after rst 5-8 hours of initial use

6. Change oil every 25 hours if operating under heavy load

or in high temperatures

Maintenance

• Save all instructions

WARNING

Before performing any maintenance, turn engine off and remove the wire from the spark plug to prevent accidental

starting and serious injury.

IMPORTANT: The warranty on this Trimmer does not cover items that have been subjected to operator abuse or negligence.

To receive full value from the warranty, the operator must maintain the trimmer as instructed in this manual, and only use

genuine replacement parts. The following table lists required periodic maintenance.

Service Records-

Fill in dates as you complete regular

service

Before

Each Use

After

Every

10 Hours

of Use

After Every

25 Hours

of

Use

After Every

50 Hours of

Use

After Every

100 Hour

of Use

Before

Each

Season

Before

Storage

See

Note

Below

Check Engine Oil Level,

Fill to Proper Level

√ √

Check Trimmer Lines and

Replace if Necessary

√ √

1

Clean Debris From Unit Including

Trimmer Head

√ √ √

2

Check Fasteners for Tightness

√ √

3

Check Fuel Line

Replace if Necessary

√ √

Lubricate Moving Parts

√ √ √

Check Spark Plug

Replace if Necessary

√ √

Check Drive Belt

Replace if Necessary

√ √

Clean Air Filter,

Replace if very Dirty

√ √

4

Change Engine Oil

√ √ √

5, 6

Replace Spark Plug

√

Clean Combustion Deposits from

cylinder, piston, and valves

√

WARNING

Use only GENUINE replacement parts. Other parts may

damage the unit or result in injury.

EN - 16

Maintenance (Continued)

• Save all instructions

How to Change the Oil

NOTE: Refer to Figure 11 when following the steps below:

1. Stop the engine and allow it to cool.

2. Disconnect spark plug wire from the spark plug.

3. Remove oil dipstick. (See Figure11)

4. Tilt engine and allow all of oil to drain into a collection pan.

IMPORTANT: Used oil is a hazardous waste. Place oil in a sealed container and take to your local recycling center. Do NOT

discard with household waste.

5. To re-fill engine with oil, see engine preparation section “How to Check Oil and Fill to Proper Level”.

How to Clean the Air Filter

A dirty air filter will restrict air intake. Periodic maintenance

of the air filter will help improve engine performance and

reduce emissions.

WARNING

Never clean air filter with gasoline or an easy ignited solvent

because it may create a fire hazard.

1. Remove the air filter cover, and carefully remove the filter

element. (See Figure 14)

2. Clean all parts. Clean filter element by gently tapping it

on a flat surface. Replace if very dirty.

3. Reinstall the filter element and air filter cover.

Figure 14

Filter Element

Air Filter Cover

EN - 17

Maintenance (Continued)

• Save all instructions

How to Replace the Trimmer Lines

When the trimmer line becomes worn to half the original

length, replace the trimmer line. For the best performance,

use a heavy gauge 0.155 in. [4 mm] trimmer line.

1. Stop the engine. Wait for all moving parts to stop.

Disconnect the wire from the spark plug.

2. Remove the worn trimmer line from line retainer.

3. Cut the length of the trimmer line to 20.25 inch (515 mm).

Use the length guide; located on the shield to make sure

the trimmer line is the correct length. (See Figure 15)

NOTE: Do not allow the length of the lines to vary more than

one inch. Make sure the trimmer head is balanced and does

not vibrate.

IMPORTANT: To extend the life of the trimmer line, keep the

trimmer line moist. If not kept moist, the nylon trimmer line

will become dry and brittle. Keep extra trimmer line in a can

of water. The line will then stay exible and easy to change.

A exible line will also last much longer.

Figure 15

Figure 16

Figure 17

Figure 18

EN - 18

How to Check the Spark Plug

Spark Plug Model: Torch K6RTC

CAUTION

Only use the recommended spark plug or a spark plug with

the same temperature range. Using an improper spark plug,

an incorrect spark plug gap, or a dirty/fouled spark plug can

reduce engine performance and cause damage.

1. Stop engine and allow it to cool.

2. Remove spark plug wire from spark plug.

3. Remove the spark plug with a size 16mm (5/8 inch) deep

well socket.

4. Visually inspect the spark plug for cracks or damage.

If cracked, replace spark plug.

5. Clean carbon deposits. If excessive carbon build up,

replace spark plug.

6. Check that the gap of the spark plug is 0.030-0.037 in.

(0.8-0.9 mm). (Figure 19)

7. Re-insert the spark plug and tighten to 20 foot-pounds

(27 Nm).

8. Reattach spark plug wire to spark plug.

Figure 19

0.030-0.037 in.

0.8-0.9 mm

Maintenance (Continued)

• Save all instructions

EN - 19

Figure 21

How to Replace the Drive Belt

WARNING

Before you remove the drive belt, disconnect the wire from

the spark plug.

1. Remove the four fasteners that holds the plastic belt guard

to the trimmer housing. (See Figure 20)

2. Remove the plastic belt guard.

3. Remove the ange nut and washer that holds the forward

drive pulley onto the trimmer head. (See Figure 20)

4. Pull straight up on the forward drive pulley to remove

from the spindle head shaft.

5. Remove the ange nut holding the idler pulley to the idler

bracket. (See Figure 21)

6. Remove the drive belt from the unit.

IMPORTANT: Only use a replacement belt from the

manufacturer. To order spare parts,

call us at: 1-800-737-2112

7. To assemble the drive belt, reverse the above steps.

8. The torque specs are

• 50-70 inch-pounds [5.7-8.0 Nm] for the belt guard.

• 27-33 foot-pounds [36.6-44.7 Nm] for the drive pulley

mounting nut.

9. Check the routing of the drive belt. Make sure the drive

belt is inside of all belt guides and that the belt is not

twisted. (See Figure 21)

IMPORTANT: Test the drive system. Start the engine and

assure that the spindle head is turning freely.

Maintenance (Continued)

• Save all instructions

Figure 20

Forward

Drive Pulley

Belt Guard

Idler

Bracket

Forward

Drive Pulley

Idler

Pulley

Engine Drive

Pulley

Drive

Belt

La page charge ...

Powermate PWFTA17322 Manuel utilisateur

Powermate PWFTA17322 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents