Rockford Fosgate Punch HE2 DVC RFP2208 Manuel utilisateur

Marque: Rockford Fosgate

Modèle: Punch HE2 DVC RFP2208

Catégorie: Subwoofers

Taper: Manuel utilisateur

INSTALLATION & OPERATION

RFP2208

RFP2210

RFP2212

RFP2215

RFR2210

RFR2212

RFR2215

RFD1208

RFD1210

RFD1212

RFD1215

RFD1218

POWER

DVC

® ®

car audio

fanatics

for

– 2 –

PUNCH HE2 DVC PUNCH HX2 DVC POWER DVC

MODEL RFP2208 RFP2210 RFP2212 RFP2215 RFD1208 RFD1210 RFD1212 RFD1215 RFD1218 RFR1210 RFR1212 RFR1215

FEATURES

Cone SPP SPP SPP SPP SPP SPP SPP SPP SPP SPP SPP SPP

Surround Foam Foam Foam Foam

Santoprene Santoprene Santoprene Santoprene Santoprene

Rubber Rubber Rubber

Basket

LX Stamped LX Stamped LX Stamped LX Stamped

LX Cast LX Cast LX Cast LX Cast LX Cast Cast Cast Cast

Voice Coil Diameter 2.0 2.5 2.5 2.5 2.5 3.0 3.0 3.0 4.0 3" 4" 4"

Aluminum Voice Coil XXXXXXXXXXXX

Hyper-Extended Pole Piece XXXXXXXXXXXX

Vented Pole Piece XXXXXXXXXXXX

Aero-Vent Back Plate XXXXXXXXXX XX

Magnet Bumper XXXXXXXXXXXX

ENCLOSURE VOLUME

Sealed (ft

) 0.30 0.75 1.25 2.5 0.30 0.75 1.25 2.5 4.0 0.75 1.25 2.5

Sealed (liters) 8.50 21.24 35.40 70.79 8.50 21.24 35.40 70.79 113.28 21.24 35.40 70.79

Vented (ft

) 0.625 1.0 2.0 2.5 0.625 1.0 2.0 2.5 4.0 1.0 2.0 2.5

Vented (liters) 17.70 28.32 56.63 70.79 17.70 28.32 56.63 70.79 113.28 28.32 56.63 70.79

SPECIFICATIONS

– 3 –

PUNCH HE2 DVC PUNCH HX2 DVC POWER DVC

MODEL RFP2208 RFP2210 RFP2212 RFP2215 RFD1208 RFD1210 RFD1212 RFD1215 RFD1218 RFR1210 RFR1212 RFR1215

SPECIFICATIONS

Nominal Impedance 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2 4Ω x 2

Fs 35 30 28 22 40 30 26 24 22 28Hz 24Hz 20Hz

Qts .37 .49 .51 .51 .50 .40 .39 .48 .48 0.34 0.38 0.35

Vas (ft

) .460 1.483 3.178 9.182 1.060 3.108 4.238 7.063 14.126 1.060 3.29 9.182

Vas (liters) 13 42 90 260 30 88 120 200 400 30 93 260

Xmax (in.) .43 .51 .51 .51 .55 .55 .55 .55 .75 0.48 0.53 0.53

Xmax (mm) 11.0 13.0 13.0 13.0 14.0 14.0 14.0 14.0 19.0 12.3 13.5 13.5

Sensitivity (dB @1w/1m) 84 85 87 89 83 85 88 89 90 85 87 89

Power Handling (RMS/Peak)

250/500 400/800 400/800 500/1000 400/800 500/1000 500/1000 600/1200 600/1200 500/1000 1000/2000 1000/2000

Speaker Displacement (ft

) .035 .06 .085 .135 .05 .12 .21 .25 .30 .12 .21 0.25

Mounting Diameter (in.) 7-1/16 9-1/2 11-1/8 13-7/8 6-7/8 9-3/16 10-13/16 13-13/16 16-5/16 9-5/32 11 13-7/8

Mounting Diameter (mm) 179 241 283 252 175 233 275 351 414 233 279 352

Mounting Depth (in.) 4-11/16 5-7/8 6-5/16 7-11/16 4-13/16 5-7/16 5-13/16 6-15/16 8-11/16 5-5/16 6-1/32 7-1/4

Mounting Depth (mm) 119 149 160 195 122 138 148 176 221 135 153 184

– 4 –

Dear Customer,

ongratulations on your purchase of the world's finest brand of car audio

speakers. At Rockford Fosgate we are fanatics about musical reproduction at

its best, and we are pleased you chose our product. Through years of engineer-

ing expertise, hand craftsmanship and critical testing procedures, we have

created a wide range of products that reproduce music with all the clarity and

richness you deserve.

For maximum performance we recommend you have your new Rockford

Fosgate product installed by an Authorized Rockford Fosgate Dealer, as we

provide specialized training through Rockford Technical Training Institute

(RTTI). Please read your warranty and retain your receipt and original carton

for possible future use.

Great product and competent installations are only a piece of the puzzle

when it comes to your system. Make sure that your installer is using 100%

authentic installation accessories from Connecting Punch in your installa-

tion. Connecting Punch has everything from RCA cables and speaker wire to

Power line and battery connectors. Insist on it! After all, your new system

deserves nothing but the best.

To add the finishing touch to your new Rockford Fosgate image order your

Rockford wearables, which include everything from T-shirts and jackets to

hats and sunglasses.

To get a free brochure on Rockford Fosgate products and Rockford wearables,

in the U.S. call 480-967-3565 or FAX 480-967-8132. For all other countries,

call +001-480-967-3565 or FAX +001-480-967-8132.

If, after reading your manual, you still have questions regarding this product,

we recommend that you see your Rockford Fosgate dealer. If you need further

assistance, you can call us direct at 1-800-669-9899. Be sure to have your seri-

al number, model number and date of purchase available when you call.

The serial number can be found on the outside of the box. Please record it in

the space provided below as your permanent record. This will serve as verifi-

cation of your factory warranty and may become useful in recovering your

speaker if it is ever stolen.

Serial Number:__________________________________

Model Number: ________________________________

PRACTICE SAFE SOUND™

CONTINUOUS EXPOSURE TO SOUND PRESSURE LEVELS

OVER

100dB MAY CAUSE PERMANENT HEARING LOSS.

HIGH POWERED AUTOSOUND SYSTEMS MAY PRODUCE

SOUND PRESSURE LEVELS WELL OVER

130dB. USE

COMMON SENSE AND PRACTICE SAFE SOUND

– 5 –

TABLE OF CONTENTS

Specifications............................................................................................2

Dear Customer..........................................................................................4

Introduction ..............................................................................................5

Power DVC Woofer Contents....................................................................5

Recommended Enclosures ........................................................................6

Wiring Configurations ..............................................................................8

Building An Enclosure ..............................................................................9

Calculating Volume ..................................................................................9

Subwoofer Crossovers ..............................................................................9

Warranty Information..............................................................................10

International Information ........................................................................11

INTRODUCTION

The Punch HE2 DVC, Punch HX2 DVC, Power DVC are high performance,

low frequency drivers with dual 4 ohm voice coils. These woofers were

designed for use primarily in small sealed & small ported enclosures. By uti-

lizing the latest materials and construction techniques, we are able to offer

a speaker with high output at low frequencies while requiring a minimum

of operating space.

CONTENTS

Punch HX2 DVC

Power HE2 DVC Woofer

Installation & Operation Manual

4 foam gasket segments

Punch HX2 DVC

Power HX2 DVC Woofer

Installation & Operation Manual

4 foam gasket segments

Power DVC

Power DVC Woofer

Installation & Operation Manual

4 foam gasket segments

– 6 –

RECOMMENDED ENCLOSURES

Punch HE2 10” - Punch HX2 10” - Power DVC 10"

Recommended Sealed 0.75ft

(21.24L)

Punch HE2 12” - Punch HX2 12” - Power DVC 12"

Recommended Sealed 1.25ft

(35.40L)

Recommended Vented 1.0 ft

(28.32L)

Recommended Vented 2.0 ft

(56.63L)

D = 13.5"

(34.29cm)

H = 13"

(33.02cm)

W = 15"

(38.1cm)

Range in Cubic Feet

1 2 3 4 5 6

0.3

.75

D = 12"

(30.48cm)

H = 14"

(35.56cm)

W = 19-3/4"

(50.17cm)

Range in Cubic Feet

1 2 3 4 5 6

0.3

1.25

1.75

D = 14"

(35.56cm)

H = 18"

(45.72cm)

W = 20.5"

(52.07cm)

Range in Cubic Feet

1 2 3 4 5 6

0.3

1.50

2.50

D = 10"

(25.40cm)

H = 14"

(35.56cm)

W = 15"

(38.10cm)

Range in Cubic Feet

1 2 3 4 5 6

0.3

.625

1.50

.75

*Fb = 35 Hz Pd = 3" (7.62cm)

Pl = 13.25" (33.65cm)

*Fb=35 Hz Pd=4" (10.16cm)

Pl=10.75" (27.30cm)

Punch HE2 8” - Punch HX2 8”

Recommended Sealed 0.30ft

(8.50L) Recommended Vented 0.625 ft

(17.70L)

D = 8"

(20.32cm)

H = 11"

(27.94cm)

W = 19.75"

(50.16cm)

Range in Cubic Feet

1 2 3 4 5 6

.50

.625

0.3

D = 8"

(20.32cm)

H = 11"

(27.94cm)

W = 11"

(27.94cm)

Range in Cubic Feet

1 2 3 4 5 6

0.3

.50

1.50

*Fb = 40 Hz Pd = 2.5" (6.35cm)

Pl = 11.25" (28.57cm)

– 7 –

Punch HE2 15” - Punch HX2 15” - Power DVC 15"

Recommended Vented 2.5ft

(70.79L)

D = 12"

(30.48cm)

H = 20"

(50.80cm)

W = 25"

(63.50cm)

Range in Cubic Feet

1 2 3 4 5 6

0.3

2.50

3.50

D = 12"

(30.48cm)

H = 20"

(50.80cm)

W = 25"

(63.50cm)

Range in Cubic Feet

1 2 3 4 5 6

0.3

2.50

2.25

Recommended Sealed 2.5ft

(70.79L)

*Fb = 35 Hz Pd = 4" (10.16cm)

Pl = 8" (20.32cm)

Punch HX2 18”

Recommended Vented 4.0ft

(113.27L)

D = 14"

(35.56cm)

H = 20.5"

(52.0cm)

W = 32.5"

(82.55cm)

Range in Cubic Feet

1 2 3 4 5 6

D = 14"

(35.56cm)

H = 20.5"

(52.0cm)

W = 32.5"

(82.55cm)

Range in Cubic Feet

1 2 3 4 5 6

0.3

Recommended Sealed 4.0ft

(113.27L)

Fb = Tuning Frequency

Pd = Port Diameter

Pl = Port Length

*Fb = 30 Hz Pd = 2x4" (2x10.16cm)

Pl = 14.5" (36.83cm)

– 8 –

WIRING CONFIGURATIONS

By varying the wiring configuration of your speakers you can create an

impedance load to match your system. Since each voice coil of a DVC

speaker carries its own impedance, altering the wiring configurations give

a range of options for impedance load. Series, Parallel, or Series-Parallel

wiring configurations are different techniques for wiring speakers that pro-

vide different loads. Series configuration is a string method where speakers

are wired end to end. Parallel configuration uses two or more speakers

wired across common terminals. Series-Parallel configuration combines

both techniques. Choose the wiring diagram below that corresponds the

number of woofers and the impedance of your amplifier.

– 9 –

BUILDING AN ENCLOSURE

To work properly, the walls of the enclosure must be rigid and not flex when

subjected to the high pressures generated by the speaker's operation. For

optimum performance, we recommend using 3/4" MDF (Medium Density

Fiberboard) and internal bracing. The enclosure should be glued together

and secured with nails or screws. MDF is porous; therefore, it is suggested

to also seal the outside walls with polyurethane.

CALCULATING VOLUME

Calculating volume is merely a matter of measuring the dimensions in inch-

es and using the formula:

If two facing sides are of uneven length, add them together and divide by

two to take the average. Using this number will give you the volume with-

out the necessity of calculating the box in sections and adding the sections

together. The thickness of the baffle material reduces the internal volume so

this must be subtracted from the outside dimensions to determine the inter-

nal volume. The speaker itself also reduces the internal volume. The

amount of air displaced by each model is listed on the specification sheet

and should also be subtracted from the gross volume calculation.

Height" x Width" x Depth"

1728 cu. in.

Box Volume =

(cubic feet)

SUBWOOFER CROSSOVERS

There are two operational types of crossovers, passive and active. Passive

crossovers (coils or inductors) are placed on the speaker leads between the

amplifier and speaker. An active crossover is an electronic filter which sep-

arates the audio signal fed to different amplifiers. For optimum subwoofer

performance, we recommend using an active 80-100Hz low-pass crossover

at 12dB/octave.

– 10 –

LIMITED WARRANTY INFORMATION

Rockford Corporation offers a limited warranty on Rockford Fosgate products on

the following terms:

• Length of Warranty

1 year on speakers 90 days on speaker B-stock (receipt required)

3 years on electronics 90 days on electronic B-stock (receipt required)

1 years on source units

• What is Covered

This warranty applies only to Rockford Fosgate products sold to consumers by

Authorized Rockford Fosgate Dealers in the United States of America or its pos-

sessions. Product purchased by consumers from an Authorized Rockford Fosgate

Dealer in another country are covered only by that country’s Distributor and not

by Rockford Corporation.

• Who is Covered

This warranty covers only the original purchaser of Rockford product purchased

from an Authorized Rockford Fosgate Dealer in the United States. In order to

receive service, the purchaser must provide Rockford with a copy of the receipt

stating the customer name, dealer name, product purchased and date of purchase.

• Products found to be defective during the warranty period will be repaired or

replaced (with a product deemed to be equivalent) at Rockford's discretion.

• What is Not Covered

1. Damage caused by accident, abuse, improper operations, water, theft

2. Any cost or expense related to the removal or reinstallation of product

3. Service performed by anyone other than Rockford or an Authorized Rockford

Fosgate Service Center

4. Any product which has had the serial number defaced, altered, or removed

5. Subsequent damage to other components

6. Any product purchased outside the U.S.

7. Any product not purchased from an Authorized Rockford Fosgate Dealer

• Limit on Implied Warranties

Any implied warranties including warranties of fitness for use and merchantabil-

ity are limited in duration to the period of the express warranty set forth above.

Some states do not allow limitations on the length of an implied warranty, so this

limitation may not apply. No person is authorized to assume for Rockford Fosgate

any other liability in connection with the sale of the product.

• How to Obtain Service

Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an

RA# (Return Authorization number) to return any product to Rockford Fosgate.

You are responsible for shipment of product to Rockford.

Ship to:

Electronics

Rockford Corporation

Warranty Repair Department

2055 E. 5th Street

Tempe, AZ 85281

RA#:_________________

Ship to:

Speakers

Rockford Acoustic Design

(Receiving-speakers)

609 Myrtle N.W.

Grand Rapids, MI 49504

RA#:_________________

– 11 –

NTERNATIONAL

INFORMATION

– 12 –

LEA DETENIDAMENTE LAS SIGUIENTES INSTRUCCIONES DE INSTA-

LACÍON DEL PRODUCTO.

INTRODUCCÍON

Los woofers Power DVC son una gama completa de drivers de baja fre-

cuéncia que comprenden diámetros de 10" a 15". Diseñada para ofrecer la

máxima calidad, los Woofers ofrecen al entusiasta principiante en sistemas

de car audio, la oportunidad para disfrutar de un bajo sólido en las bajas

frecuéncias. Nuestros ingenieros han seleccionado materiales y técnicas

para la construcción de nuestros altavoces con el objetivo de ofrecer

características y confianza comparable a otros altavoces vendidos much

más caros.

CALCULO DEL VOLUMEN

Para calcular el volumen sólo se han de medir las dimensiones en cen-

timetros y aplicar la fórmula:

Volumen

du la caja =

(en litros)

Si dos caras opuestas son de diferente tamaño, súmelas y divida el total por

dos para obtener el promedio. Usando esta técnica se ahorrara el cálculo

por secciones. El espesor del material con que está construida la caja

reduce el volumen interno, de manera quer ha de restarse de las dimen-

siones exteriores para determinar el volumen interior. La cantidad de aire

que ocupa cada modelo viene especificado en la hoja de caracteristicas y

también debe sustraerse para obtener el volumen neto interior.

CONSTRUCCION DE UN RECINTO

Para un buen funcionamiento las paredes del recinto han de ser rigidas y

sin flexión a altas presiones de aire. Recomendamos usar un espesor de 1.9

cm de conglomerado de alta densidad o fibra de media densidad. Si el

recinto es muy grande es necessario reforzarlo internamente. Las juntas

deben ser encoladas y aseguradas con tornillos o grapas. Internamente las

juntas deben ser selladas con silicona para prevenir las fugas de aire. La

cola para madera es la mejor opción. Debido a la porosidad del conglom-

erado de alta densidad y la fibra es recomendable sellar exteriormente la

caja con poliuretano.

Alto x Ancho x Profundidad

1000

ESPAÑOL

– 13 –

VEUILLEZ LIRE LES INSTRUCTIONS SUIVANTES POUR L'INSTALLATION

DE CE PRODUIT.

INTRODUCTION

Les woofers Power DVC sont une gamme complète de haut-parleurs de

graves allant de 25 à 38 cm et disponibles en 4Ωx2. En utilisant les tech-

niques et les matériaux de construction les plus récents, nous sommes

parvenus à construire un haut-parleur fournissant un rendement élevé dans

les graves tout en requérant un volume opérationnel minimum.

CALCUL DU VOLUME

On calcule le volume en mesurant la dimension de chaque côté et en util-

isant la formule suivante:

Volume

du caisson =

(Litres)

Hauteur (cm) x Longueur (cm) x Largeur (cm)

1000

Si les due côtés qui se font face n'ont pas la même longueur, additionnez

les et divisez le résultat par deux pour obtenir la moyenne des deux

longueurs. Utilisez le nombre ainsi obtenu dans la formule pour détermin-

er le litrage. Cette méthode permet d'obtenir le volume du caisson sans

devoir faire de calculs compliqués de section de volume. L'épaisseur du

matériau dont est fait le caisson réduit le volume interne de celui-ci.

Lorsqu'on mesure les côtés du caisson il ne faut donc pas oublier d'oter des

mesures l'epaisseur du matériau. Le haut-parleur lui-même diminue le vol-

ume interne du caisson. Le volume d'air déplacé par chaque modèle de

haut-parleur est repris dans les spécifications techniques et doit également

être soustrait du volume total.

CONSTRUIRE UN CAISSON

Pour fonctionner convenablement les parois du caisson doivent être rigides

lorsqu'elles sont soumises aux hautes pressions dues au fonctionnement du

haut-parleur. Nous vous recommandons d'utiliser des panneaux de bois

aggloméré à haute ou moyenne densité de particules de type “MDF”. Ces

panneaux sont disponibles dans la plupart des magasins de bricolage. Pour

un caisson de grand volume il est recommandé de placer des renforts à l'in-

térieur du caisson. Les différents côtés devront être collés (colle à bois) et

vissés (ou éventuellement cloués). Il est recommandé de mettre un joint de

silicone dans les arêtes internes du caisson afin d'éviter les fuites d'air. Du

fait de la porosité des matériaux que nous vous conseillons il est préférable

de recouvrir l'extérieur du caisson avec du polyuréthane.

FRANÇAIS

– 14 –

BITTE LESEN SIE DIESE GEBRAUCHSANLEITUNG ZUERST SORGFÄLTIG

DURCH. DAS KANN SIE VOR FALSCHEM EINSATZ, AUSFALLEN ODER SOGAR

BESCHÄDIGUNG DES PRODUKTES ODER IHRES FAHRZEUGES SCHÜTZEN.

EINLEITUNG

Die Power DVC Woofer sind eine komplette Produktlinie von Tief-

Frequenzlautsprechern mit Durchmesser von 25 cm bis zu 38 cm, erhältlich

in der Impendanz 4 Ohm x 2. Durch die Verwendung neuester Materialien

und Produktionstechniken können wir Ihnen heute einen Lautsprecher

vorstellen, der hohe Lautstärken und tiefe Frequenzen selbst in sehr kleinen

Volumen reproduzieren kann.

VOLUMEN-BERECHNUNG

Zur Volumen-Berechung benötigen sie die genauen Mabe und

Dimensionen in Zentimetern.

Gehäuse-

Volumen =

(Kubik Liter)

Höhe (cm) x Breite (cm) x Tiefe (cm)

1000

Sollten zwei gegenüberliegende Seiten ungleich lang sein, so können sie

die Mabe zusammen rechnen und durch zwei dividieren um den

Durchschnitt zu erhalten. Dies macht Ihnen die Berechnung leichter und

Sie müssen das Gehäuse nicht in Sektionen berechnen, die Sie danach

wieder mühselig zusammen zählen müssen. Die Materialstärke beeinflubt

natürlich auch das Innen-Volumen, so muss für eine präzise Berechnung

die Materialstärke von Auben-Volumen abgezogen werden. Der

Lautsprecher verringert ebenfalls das Innen-Volumen, auch er sollte natür-

lich heraus gerechnet werden. Jedes Lautsprecher-Volumen ist unter

“Specifications” genau aufgelistet.

DER GEHÄUSE BAU

Um das Gehäuse so präzise wie möglich zu bauen, sollten die

Gehäusewände sehr steif und luftundurchlässig sein, um dem entsehenden

Luftdruck des Lautsprechers standhalten zu können. Wir empfehlen 1,9 cm

mittelverdichtete Faserplatte (MDF), die in den meisten Baumärkten ange-

boten wird. Bei einem grö

βeren Gehäuse sollten Sie Versteifungen durch

Holzbalken montieren. Diese sollten – wie auch das gesamte Gehäuse –

mit Holzleim geklebt und verschraubt oder vernagelt sein. Um eine höhere

Dichte zu erreichen, empfiehlt es sich, die Kanten und Verschraubungen

mit Silikon abzudichten und das Gehäuse von innen mit einer

Hohlraumversiegelung zu behandeln.

DEUTSCH

– 15 –

LEGGERE CON ATTENZIONE LE SEGUENTI ISTRUZIONI PRIMA DEL-

L'INSTALLAZIONE DEL PRODOTTO.

INTRODUZIONE

I woofer Power DVC sono una linea completa di altoparlanti per basse fre-

quenze con diametri che vanno da 25 a 38 cm e disponibili sia a

4 ohm x 2. Impiegando le piú aggiomate tecnologie e materiali, siamo in

grado di offrire altoparlanti che possono riprodurre un'elevata pressione

sonora alle basse frequenze mantenendo i volumi di impiego assolutamente

ridotti.

CALCOLO DEL VOLUME

Calcolare il volume é essenzialmente solo un problema di misurazione

delle dimensioni in centimetri della cassa e di applicazione della formula:

Se due pareti parallele sono di dimensioni diverse (prisma), semplicemente

Volume

della cassa =

(litri)

Alteza x Larghezza x Profonditá

1000

sommatele e dividete il risulto per due. Impiegando il risultato ottenuto

potete calcolare il volume senza dividere la cassa i sezioni. Lo spessore del

legno riduce il volume interno, per cui é necessario sottrario dalle dimen-

sioni esterne. Anche il volume dell'altoparlante stesso riduce il volume

della cassa e deve essere sottratto. Il volume che ciascun altoparlante

contribuisce a togliere dalla cassa é indicato nelle tabelle con le specifiche.

COSTRUIRE UNA CASSA

Per ottenere le prestazioni massime, le pareti della cassa devono essere

rigide e non flettere sotto la sollecitaxione della elevata pressione generata

dal woofer. Noi raccomandiamo l'impiego di MDF con uno spessore min-

imo di 19 mm, materiale facilmente reperibile in tutte le falegnamerle. Per

casse di dimensioni molto grandi é indispensabile prevedere dei rinforzi

interni. Le giunture devono essere incollate e fissate con viti o chiodi in

abbondanza. Intermanmente le giunture devono essere siliconate per

impedire trafilati d'aria. Anche la colla da legno funziona bene. Essendo il

MDF un materiale poroso si consiglia di sigillare l'esterno con materiali

poliuretanici.

ITALIANO

Installation assistance available at:

http://www.rockfordfosgate.com/rftech

Rockford Fosgate

Rockford Corporation

546 South Rockford Drive

Tempe, Arizona 85281 U.S.A.

In U.S.A., (480) 967-3565

In Europe, Fax (49) 8503-934014

In Japan, Fax (81) 559-79-1265

www.rockfordfosgate.com

MADE IN THE USA

This product is designed, developed and assembled in the USA by a dedicated

group of American workers. The majority of the components used in the con-

struction of this product are produced by American companies. However, due to

the global nature of their manufacturing facilities and the loudspeaker parts

industry in general, some parts may be manufactured in other countries.

11/99 E.R.

LIT10683

Rockford Fosgate Punch HE2 DVC RFP2208 Manuel utilisateur

Marque: Rockford Fosgate

Modèle: Punch HE2 DVC RFP2208

Catégorie: Subwoofers

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Rockford Fosgate Punch HE2 DVC RFP2208 User manual

Rockford Fosgate Punch HE2 DVC RFP2208 Manuel utilisateur

Rockford Fosgate Punch HE2 DVC RFP2208 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents