NEC PlasmaSync® 50VP1 Le manuel du propriétaire

Marque: NEC

Modèle: PlasmaSync® 50VP1

Catégorie: Téléviseurs à écran plasma

Taper: Le manuel du propriétaire

NEC Technologies

PlasmaSync Plasma Monitor

User’s Manual

Important Information

Warnings and Safety Precaution

The NEC PlasmaSync 42/50PD1(Model PX-42/

50VP1A) is designed and manufactured to provide

long, trouble-free service. No maintenance other than

cleaning is required. Use a soft dry cloth to clean the

panel. Never use solvents such as alcohol or thinner

to clean the panel surface.

The plasma display panel consists of fine picture ele-

ments (cells). Although NEC produces the plasma dis-

play panels with more than 99.99 percent active cells,

there may be some cells that do not produce light or

remain lit.

For operating safety and to avoid damage to the unit,

read carefully and observe the following instructions.

To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid inter-

nal heat build-up. Do not cover rear vents or install in a

closed cabinet or shelves.

The unit is equipped with cooling fans. If you install

the unit in an enclosure, be sure there is adequate space

at the top of the unit to allow hot air to rise and escape.

If the monitor becomes too hot, the overheat protector

will be activated and the monitor will be turned off. If

this happens, turn off the power to the monitor and un-

plug the power cord. If the room where the monitor is

installed is particularly hot, move the monitor to a cooler

location, and wait for the monitor to cool for 60 min-

utes. If the problem persists, contact your NEC dealer

for service.

2. Do not use the power cord polarized plug with exten-

sion cords or outlets unless the prongs can be completely

inserted.

3. Do not expose unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to

modify the power cord.

5. Unplug unit during electrical storms or if unit will not

be used over a long period.

6. Do not open the cabinet which has potentially danger-

ous high voltage components inside. If the unit is dam-

aged in this way the warranty will be void. Moreover,

there is a serious risk of electric shock.

7. Do not attempt to service or repair the unit. NEC is not

liable for any bodily harm or damage caused if unquali-

fied persons attempt service or open the back cover.

Refer all service to authorized NEC Service Centers.

8. Do not attempt to install or mount the unit yourself.

Please contact your NEC dealer for installation.

Precautions

Please read this manual carefully before using your NEC

PlasmaSync 42/50PD1 42/50inch Plasma Monitor and keep

the manual handy for future reference.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER. NO

USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

This symbol warns the user that uninsulated

voltage within the unit may have sufficient

magnitude to cause electric shock. There-

fore, it is dangerous to make any kind of

contact with any part inside of this unit.

This symbol alerts the user that important

literature concerning the operation and

maintenance of this unit has been included.

Therefore, it should be read carefully in

order to avoid any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE

THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE

THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD

RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS

CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE

CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PER-

SONNEL.

DOC compliance Notice

This Class A digital apparatus meets all requirements of

the Canadian Interference-Causing Equipment Regulations.

WARNING

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his

own expense.

CAUTION

To avoid damage and prolong operating life:

1. Use only with 120V 50/60Hz AC power supply. Con-

tinued operation at line voltages greater than 120 Volts

AC will shorten the life of the unit, and might even

cause a fire hazard.

2. Handle the unit carefully when installing it and do not

drop.

3. Locate set away from heat, excessive dust, and direct

sunlight.

4. Protect the inside of the unit from liquids and small

metal objects. In case of accident, unplug the unit and

have it serviced by an authorized NEC Service Center.

5. Do not hit or scratch the panel surface as this causes

flaws on the surface of the screen.

6. As is the case with any phosphor-based display (like a

CRT monitor, for example) light output will gradually

decrease over the life of a Plasma Display Panel.

Recommendations to avoid or minimize phosphor burn-in

Like all phosphor-based display devices and all other gas

plasma displays, PlasmaSync monitors can be susceptible

to phosphor burn under certain circumstances. Certain

operating conditions, such as the continuous display of a

static image over a prolonged period of time, can result in

phosphor burn if proper precautions are not taken. To pro-

tect your investment in this NEC PlasmaSync monitor,

please adhere to the following guidelines and recommen-

dations for minimizing the occurrence of image burn:

* Always enable and use your computer's screen saver

function during use with a computer input source.

* Display a moving image whenever possible.

* Always power down the monitor when you are finished

using it.

If the PlasmaSync monitor is in long term use or continu-

ous operation take the following measures to reduce the

likelihood of phosphor burn: (See page 42, 44, 45)

* Lower the Brightness and Contrast levels as much as

possible without impairing image readability. (See page

24, 29)

* Display an image with many colors and color gradations

(ie. photographic or photo-realistic images).

* Create image content with minimal contrast between light

and dark areas, for example white characters on black

backgrounds. Use complementary or pastel color when-

ever possible.

* Avoid displaying images with few colors and distinct,

sharply defined borders between colors.

Contact NEC Technologies at 1-800-836-0655 for other

recommended procedures that will best suit your particu-

lar application needs.

NOTE:

When you connect a computer to this monitor, attach

the supplied ferrite cores. If you do not do this, this

monitor will not comform to mandatory FCC standards.

Attaching the ferrite cores.

Set the ferrite cores on the both ends of the DVI cable

(not supplied), and the one end of the power cable (sup-

plied).

Close the lid tightly until the clamps click.

Set side

(Plasma Monitor side)

DVI cable (not supplied)

core (small)

Connector

Power cable (supplied)

core (large)

Mises en garde et précautions de

sécurité

Le moniteur multimédia NEC PlasmaSync 42/

50PD1(Modèle PX-42/50VP1A) a été conçu et

fabriqué pour une utilisation fiable et durable. Il ne

nécessite aucun entretien en dehors du nettoyage.

Utiliser un chiffon doux et sec pour nettoyer la surface

de l'écran. Ne jamais utiliser de solvant comme l'alcool

ou le diluant. Le panneau à affichage plasma est

constitué de fines particules d'images ou pixels

(cellules). Bien que NEC produise des panneaux à

affichage plasma avec plus de 99,99 % de cellules

actives, il peut y avoir des cellules qui ne produisent

pas de lumière ou qui restent allumées.

Pour des raisons de sécurité et pour éviter

d'endommager l'appareil, lire attentivement les in-

structions suivantes.

Pour éviter les risques d'éléctrocution et d'incendie:

1. Laisser suffisament d'espace autour de l'appareil pour

la ventilation et éviter toute augmentation excessive de

la température interne. Ne pas couvrir les évents ou

l'installer dans un endroit trop exigu.

L'appareil est équipé de ventilateurs de refroidissement.

Si vous installez l'appareil dans un espace clos, assurez-

vous qu'il y ait suffisamment d'espace au dessus pour

permettre à l'air chaud de s'élever et de s'évacuer.

Si la température du moniteur devient excessive, la pro-

tection contre les surchauffes entrera en action et

coupera l'alimentation. Dans ce cas, éteindre l'appareil

et débrancher le câble d'alimentation. Si la température

de la pièce dans laquelle le moniteur est installé est

particulièrement excessive, déplacer l'appareil dans un

endroit plus frais et le laisser refroidir 60 minutes. Si le

problème persiste, prendre contact avec le revendeur

NEC pour le service après-vente.

2. Ne pas utiliser la fiche polarisée du cordon

d’alimentation avec des prolongateurs ou des prises de

courant, sauf si les lames peuvent être insérées à fond.

3. Ne pas exposer à L'eau ou à l’humidité.

4. Eviter d’endommager le cordon d’alimentation, et ne

pas modifier le cordon d’alimentation.

5. Débrancher l’appareil pendant les tempêtes ou si

l’appareil n’est pas utilisé pendant une longue période.

6. Ne pas ouvrir le coffret. Des composants de haute ten-

sion se trouvent à l’intérieur. Si l’appareil est

endommagé de cette manière, la garantie devient

caduque. De plus, il y a risque d’électrocution.

7. Ne pas essayer de réparer ou entretenir l’appareil soi-

même. NEC ne saura être tenu pour responsable pour

toute blessure ou dommage causé par des personnes

non qualifiées qui essayent de réparer ou d’ouvrir le

couvercle arrière. Confier toute réparation à un centre

de service agréé NEC.

8. N’essayez pas d’installer ou d’assembler l’appareil

vous- mêmes. Veuillez contacter votre revendeur NEC

pour l’installation.

Précautions

Veuillez lire ce manuel avec attention avant d'utiliser votre

PlasmaSync 42/50PD1 NEC - Moniteur Plasma 42/50

pouces et conserver ce manuel à portée de la main pour

une consultation ultérieure.

RISQUE D’ELECTROCUTION

NE PAS OUVRIR

MISE EN GARDE: AFIN DE REDUIRE LES RISQUES D’ELECTRO-

CUTION, NE PAS DEPOSER LE COUVERCLE, IL N’Y

A AUCUNE PIECE UTILISABLE A L’INTERIEUR DE

CET APPAREIL. NE CONFIER LES TRAVAUX

D’ENTRETIEN QU’A UN PERSONNEL QUALIFIE.

Ce symbole a pour but de prévenir l’utilisateur de la

présence d’une tension dangereuse, non isolée se trouvant

à l’intérieur de l’appareil. Elle est d’une intensité suffisante

pour constituer un risque d’électrocution. Eviter le con-

tact avec les pièces à l’intérieur de cet appareil.

Ce symbole a pour but de prévenir l’utilisateur de la

présence d’importantes instructions concernant l’entretien

et le fonctionnement de cet appareil. Par conséquent, elles

doivent être lues attentivement afin d’éviter des problèmes.

AVERTISSEMENT

AFIN DE REDUIRE LES RISQUES D’INCENDIE OU

D’ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA

PLUIE OU A L’HUMIDITE. AUSSI, NE PAS UTILISER LA FICHE

POLARISEE AVEC UN PROLONGATEUR OU UNE AUTRE PRISE

DE COURANT SAUF SI CES LAMES PEUVENT ETRE INSEREES

A FOND. NE PAS OUVRIR LE COFFRET, DES COMPOSANTS

HAUTE TENSION SE TROUVENT A L’INTERIEUR. LAISSER A

UN PERSONNEL QUALIFIE LE SOIN DE REPARER CET

APPAREIL.

DOC avis de conformation

Cet appareil numérigue de la classe A respecte toutes les exi-

gences du Réglement sur le Matériel Brouilleur du Canada.

AVERTISSEMENT

Cet équipement a été testé et certifié conforme avec les limi-

tations des équipements numériques de Classe A,

conformément à l'article & (du règlement FCC. Ces limites sont

conçues pour assurer une protection raisonnable contre les

interférences nuisibles lorsque l'équipement est utilisé en mi-

lieu commercial. Cet équipement génère, utilise, et peut

produire de l'énergie de fréquence radio et, s'il n'est pas installé

et utilisé selon le manuel d'instruction, peut provoquer des

interférences nuisibles aux communications radio. L'utilisation

de cet équipement dans une zone résidentielle est suscepti-

ble de provoquer des interférences nuisibles, dans quel cas

l'utilisateur est tenu de remédier à ces interférences à ses frais.

ATTENTION

Pour éviter des dommages et prolonger la durée de

service de l’appareil:

1. N’utiliser qu’une source d’alimentation de 120 V 50/

60 Hz CA. Le fait d’utiliser l’appareil en continu à des

tensions de ligne supérieures à 120 Volts CA réduit sa

durée de vie et risque de provoquer un incendie.

2. Manipuler l’appareil avec soin pendant son déplacement

et ne pas le faire tomber.

3. Eloigner l’appareil des endroits chauds, très poussiéreux

et exposés en plein soleil.

4. Eviter que des liquides et des petits objets métalliques

pénètrent à l’intérieur de l’appareil. En cas d’accident,

débrancher l’appareil et le confier à un centre de serv-

ice agréé NEC.

5. Ne pas frapper ou rayer la surface de la écran plasma,

car des défauts risquent de se produire sur la surface de

la écran plasma.

6. Comme c'est le cas pour tout affichage à base de

phosphore (comme un moniteur CRT, par exemple), la

puissance de lumière baisse graduellement au cours de

la vie du Panneau d'Affichage à Plasma.

Pour éviter le risque de combustion au phosphore, les

mesures suivantes sont recommandées :

Comme tous les appareils d'affichage à base de phosphore

et tous les autres affichages à gaz plasma, les moniteurs

Plasmasync peuvent être sujets à la combustion au

phosphore dans certaines circonsatnces. Certaines condi-

tions d'utilisation, telles que l'affichage continu d'une im-

age statique pour une durée prolongée, peuvent causer des

brûlures au phophore si aucune précaution n'est prise. Pour

protéger votre investissement dans ce moniteur PlasmaSync

NEC, veuillez suivre les directives et les recommandations

suivantes pour minimiser l'occurence de brûlure d'image :

• Assurez-vous de mettre en marche et d'utliser

l'économisateur d'écran chaque fois que c'est possible

lorsque vous l'utilisez avec une source d'entrée

d'ordinateur.

• Affichez une image en mouvement aussi souvent que

possible.

• Coupez toujours l'alimentation lorsque vous avez terminé

d'utiliser la moniteur.

Si le PlasmaSync moniteurs est en usage continu ou longue

durée, prenez les mesures suivantes afin d'éviter l'occurence

de combustion au phosphore :

• Abaissez le niveau de l'image (contraste, luminosité)

autant que possible, sans faire perdre la lisibilité de

l'image.

• Affichez une image avec de nombreuses couleurs et

graduations de couleur (par ex. des images

photographiques ou photo-réalistes).

• Créez un contenu d'image avec un contraste minimal

entre les zones sombres et les zones claires, par exemple,

des caractères blancs sur un fond noir. Utilisez des

couleurs complémentaires ou pastels le plus souvent

possible.

• Évitez d'afficher des images avec peu de couleurs et des

limites nettes et clairement définies entre les couleurs.

Contactez NEC Technologies au 1-800-836-0655 pour

d'autres procédures recommandées qui conviendront le

mieux au besoin de votre appareil.

REMARQUE:

Lorsque vous branchez un micro-ordinateur sur ce

moniteur, fixez les noyaux en ferrites fournis. Si vous

ne le faîtes, le moniteur ne sera pas en conformité avec

les exigences des standards FCC.

Fixation des noyaux en ferrite.

Installez les noyaux en ferrite sur chaque bout du câble

DVI (non fourni), ainsi que sur un côté du câble

d’alimentation électrique (fourni).

Fermez doucement le couvercle jusqu’à ce que les

crans se clipsent.

Câble DVI (non fourni)

noyau (petit)

connecteur

câble d’alimentation électrique

(fourni)

côté de l’appareil

(côté du moniteur à plasma)

noyau (large)

NEC Technologies, Inc. (hereinafter NECTECH) warrants

this product to be free from defects in material and work-

manship under the following terms and, subject to the con-

ditions set forth below, agrees to repair or replace (at

NECTECH's sole option) any part of the enclosed unit

which proves defective. Replacement parts or products may

be new or refurbished and will meet specifications of the

original parts or product.

HOW LONG IS THE WARRANTY?

Parts and labor are warranted for (1) One Year from the

date of the first customer purchase.

WHO IS PROTECTED?

This warranty may be enforced only by the first purchaser.

WHAT IS COVERED AND WHAT IS NOT COVERED

Except as specified below, this warranty covers all defects

in material or workmanship in this product. The following

are not covered by the warranty:

1. Any product which is not distributed in the U.S.A. or

Canada and Mexico by NECTECH or which is not

purchased in the U.S.A. or Canada or Mexico from an

authorized NECTECH dealer.

2. Any product on which the serial number has been de-

faced, modified or removed.

3. Damage, deterioration or malfunction resulting from:

a.Accident, misuse, abuse, neglect, fire, water, light-

ning or other acts of nature, unauthorized product

modification, or failure to follow instructions sup-

plied with the product.

b.Repair or attempted repair by anyone not authorized

by NECTECH.

c.Any shipment of the product (claims must be pre-

sented to the carrier).

d.Removal or installation of the product.

e.Any other cause which does not relate to a product

defect.

f. Burns or residual images upon the phosphor of the

panel.

4. Cartons, carrying cases, batteries, external cabinets,

magnetic tapes, or any accessories used in connection

with the product.

5. Service outside of the U.S.A. and Canada.

WHAT WE WILL PAY FOR AND WHAT WE WILL

NOT PAY FOR

We will pay labor and material expenses for covered items,

but we will not pay for the following:

1. Removal or installation charges.

2. Costs of initial technical adjustments (set-up), includ-

ing adjustment of user controls. These costs are the re-

sponsibility of the NECTECH dealer from whom the

product was purchased.

3. Payment of shipping charges.

HOW YOU CAN GET WARRANTY SERVICE

1. To obtain service on your product, consult the dealer

from whom you purchased the product.

2. Whenever warranty service is required, the original

dated invoice (or a copy) must be presented as proof of

warranty coverage. Please also include in any mailing

your name, address and a description of the problem(s).

3. For the name of the nearest NECTECH authorized serv-

ice center, call NECTECH at 800-836-0655.

LIMITATIONS OF LIABILITY

Except for the obligations specifically set forth in this war-

ranty statement, we will not be liable for any direct, indi-

rect, special, incidental, consequential, or other types of

damages, whether based on contract, tort, or any other le-

gal theory, whether or not we have been advised of the

possibility of such damages.

This warranty is in lieu of all other warranties express or

implied, including, but not limited to, the implied warran-

ties of merchantability or fitness for a particular purpose.

EXCLUSION OF DAMAGES

NECTECH' s liability for any defective product is limited

to the repair or replacement of the product at our option.

NECTECH shall not be liable for:

1. Damage to other property caused by any defects in this

product, damages based upon inconvenience, loss of

use of the product, loss of time, commercial loss; or

2. Any other damages whether incidental, consequential

or otherwise. Some states do not allow limitation on

how long an implied warranty lasts and/or do not allow

the exclusion or limitation of incidental or consequen-

tial damages, so the above limitations and exclusions

may not apply to you.

HOW STATE LAW RELATES TO THE WARRANTY

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

FOR MORE INFORMATION, TELEPHONE 800-836-

0655

NEC TECHNOLOGIES, INC.

1250 N. Arlington Heights Road, Suite 500

Itasca, Illinois 60143-1248

Note:

All products returned to NECTECH for service

MUST have prior approval. To get approval, call NEC

Technologies at 800-836-0655.

Limited Warranty Plasma Monitors

Contents

How to Attacch Options to the Plasma Monitor .............................................................................................8

Introduction

Introduction to the PlasmaSync 42/50PD1 ...................................................................................... 9

The features you’ll enjoy include ..................................................................................................... 9

Contents of the Package.................................................................................................................. 9

OPTIONS...................................................................................................................................... 9

Setup Procedure .........................................................................................................................................10

Part Names and Functions

Front View .................................................................................................................................. 12

Side View Terminal Board L/R...................................................................................................... 13

Remote Controller........................................................................................................................ 14

Battery Installation and Replacement .............................................................................................................

Operating Range / Using the wired remote control mode ................................................................................16

Making the DIP Switch Settings

DIP Switch Functions and Settings ................................................................................................. 17

Power Management Function ....................................................................................................... 18

Power Management Modes.......................................................................................................... 18

Installation

Wiring Diagram.......................................................................................................................... 19

Connecting Your PC or Macintosh Computer ................................................................................. 20

Connections with Equipment that has a Digital Interface ................................................................. 20

Connecting Your VCR or Laser Disc Player .................................................................................... 20

Connecting Your Document Camera ............................................................................................. 20

Daisy-chaining Your monitors....................................................................................................... 21

Operation

Power/General Controls/Adjustment of the Display ....................................................................... 22

Adjustment of the Display (Direct) ................................................................................................. 23

Returning the Screen Adjustment to the Factory Default Settings (NORMAL) ..................................... 23

Adjustment of the Image .............................................................................................................. 24

Returning the Image Adjustments to the Factory Default Settings (NORMAL)..................................... 24

Adjustment of the Display (Menu Control)

List of Setting Details .................................................................................................................... 25

Before Making Adjustments .......................................................................................................... 26

To Reset the Adjustment Value (to the Factory Default Setting) During the Setting............................... 27

Adjustment of the Image (Visual Controls)...................................................................................... 29

Adjustment of Screen Position (Horizontal) .................................................................................... 30

Adjustment of Screen Position (Vertical)......................................................................................... 31

Color Temperature ....................................................................................................................... 32

Adjustment of the White Balance .................................................................................................. 33

Adjustment of the On-screen Display Position ................................................................................ 34

Setting the On-screen Display OFF Time........................................................................................ 35

Adjustment of the Clock Frequency/Clock Phase (AUTO PICTURE) .................................................. 36

Normal Screen............................................................................................................................ 37

Next Page Screen........................................................................................................................ 38

Information Screen ...................................................................................................................... 39

Timer Screen............................................................................................................................... 40

Auto Timer Screen ....................................................................................................................... 41

Multiple Screens.......................................................................................................................... 43

Other Setting Screens (1) ............................................................................................................. 44

Other Setting Screens (2) ............................................................................................................. 45

Set Selection Screen for Allotting ID Numbers to Multiple Screens/Each Set ..................................... 46

Troubleshooting ..........................................................................................................................................47

Specifications .............................................................................................................................................48

Appendix

Signal Identification For Raster Preset............................................................................................ 50

Pin Configuration and Signal Level of mini D-Sub 15-Pin (Analog) Input Connector.......................... 51

Pin Configuration and Signal of the RGB 3 IN Connector (DVI Connector) ....................................... 51

Function and Pin Configuration of the External Control Connector ................................................... 52

Cabinet dimensions ................................................................................................... 63

How to Attach Options to the Plasma Monitor

Drawing A

Drawing B

45mm (1.77")

mm (1.97")

mm

(1.22")

mm 

(1.22")

Wall



Ventilation Requirements for

enclosure mounting

To allow heat to disperse, leave space between

surrounding objects as shown on the diagram be-

low when installing.

You can attach your optional mounts or stand to the plasma

monitor in one of the following two ways:

* In the upright position. (See Drawing A)

* Lay the screen face down (See Drawing B). Lay the

protective sheet, which was wrapped around the monitor

when it was packaged, beneath the screen surface so as

not to scratch the screen face.

• This device cannot be installed on its own.

Be sure to use a stand or optional mounting

unit. (Wall mount unit, Stand, etc)

* See page 2.

• For correct installation and mounting it is

strongly recommended to use a

trained,authorized NEC dealer.

Failure to follow correct mounting proce-

dures could result in damage to the equip-

ment or injury to the installer.

Product warranty does not cover damage

caused by improper installation.

Notice:

* Installation of only the main unit is not possible. Be sure

to use and install the main unit in conjunction with a

stand or special unit.

Note:

RETRACTABLE FEET ARE FOR TEMPORARY USE

ONLY AND ARE NOT INTENDED FOR PERMA-

NENT INSTALLATION.

MODEL # PX-42VPU1-ST STAND IS REQUIRED

FOR PERMANENT TABLETOP INSTALLATION.

REPLACE THE FEET WHEN YOU MOVE THE

MONITOR.

Pulling Out and Reinserting the

Retractable Stand

Retractable Stand are housed at 2 locations on the bottom

surface of the main unit.

1. Grasp the end and pull out.

2. The stand will open automatically when your hand is

removed.

To house the Retractable Stand, close them and then con-

tinue to push them inside the main unit.

Introduction

Contents of the Package

The following lists all of the items included in your

MultiSync multimedia monitor package. Please save the

original box and packing materials for future

transportation or shipment of this monitor.

1. PlasmaSync 42/50PD1

2. Power cord

3. Wireless/Wired remote control unit and two AAA

batteries

4. Remote cable

5. RGB cable (15-Pin mini D-Sub To 15-pin mini D-Sub

Connector)

6. User' s manual

7. Core (large) and two cores (small)

OSM and IPM are trademarks of NEC Technologies, Inc.

IBM PC/AT, PS/2, VGA, S-VGA, 8514/A and XGA are

registered trademarks of International Business Machines

Corporation.

Apple and Macintosh are registered trademarks of Apple

Computer, Inc.

Microsoft is a registered trademark of Microsoft

Corporation. Windows is a trademark of Microsoft

Corporation.

Introduction to the PlasmaSync

42/50PD1

This section introduces you to your new PlasmaSync 42/

50PD1, provides a list of materials that comes with your

monitor and describes the features and controls.

The features you’ll enjoy include:

* This unit can be used with IBM PC/AT compatible,

Macintosh, and compatibles.

(For details, see “Factory Setting Values Preset Table.”

* Easy-to-operate multifunction remote control and

external control connector

A single remote control can be used as a wireless or as a

wired remote control (with automatic switching by cable

connection) and the remote THROUGH OUT connector

permits simultaneous operation of multiple monitors.

(A maximum of 3 units can be connected.)

The external control connector with a THROUGH OUT

feature permits various control functions to be made

externally.

* ID No. settings can be made for up to 256 units.

* NTSC, PAL, SECAM, and M-NTSC composite video

signals can be accommodated

Video signals from video cameras, video decks, video

disc players, and other video equipment adhering to

NTSC as well as PAL, SECAM, and M-NTSC (with a

4.43 MHz chroma signal) standards can be selected on

screen.

* Varied set of input connectors

Video input signals: BNC video connector, S video

connector. Each type is equipped with its own

THROUGH OUT connector, single system.

Analog RGB input: mini D-Sub 15-pin connector, BNC

(R, G, B, H/CS, V connectors). BNC is equipped with its

own THROUGH OUT connector, single system.

* Can be used with Digital RGB input (DVI standard

compliant)

* Can be used with multiple screens

* Power management function

RGB3 input mode complies with DMPM (Digital

Monitor Power Management) of DVI.

A great reduction in power consumption when not being

used is achieved through the VESA-proposed DPMS

system.

The unit can also be used with the Energy Star standard

(in which case power consumption will be 15 W or less

when not being used).

* The personal computer and the operating system that are

to be connected must be compatible with VESA DPMS.

Personal computers that are to be connected to the RGB3

input must be compatible with DVI DMPM.

* OSM (On Screen Manager) function

The OSM function displays a variety of screen adjustment

and correction menus on the screen to allow fine settings

to be made.

* Plug and Play compatible

The RGB3 input is compatible with DDC2B only.

Ready to be used with Plug and Play which are supported

by Windows 98 and Windows 95.

(VESA DDC1 and DDC2 level B)

* Windows 98 or Windows 95 and a personal computer

with VESA DDC are required to use Plug and Play.

* Can be used with RS-232C

1.Determine the installation location

* To ensure safe use, see “Before Use” and “Observe

the Following,” then install properly.

2.Connect the equipment

Set the termination switch (75Ω/high impedance).

Set the DIP switches to suit the application and system

structure. (See Page 17.)

(Loop-out connections are for one unit, maximum.)

3.Install the remote control batteries.

* To use the remote control in the wired arrangement,

connect the supplied remote control cable.

4.Connect the supplied power cable

* The maximum current rating 5.6(A) : 42PD1

* The maximum current rating 7.4(A) : 50PD1

5.Switch on the power of each of the

devices

* When connected with a computer, switch on the

power of the computer first.

6.Input an analog RGB signal or a video

signal to this unit

7.Select the input mode

* Select the appropriate RGB input or video input.

8.Adjust the screen

* Make adjustments when adjustment of the screen

display position or distortion is required.

9.Adjust the image

* Make adjustments when adjustment of the tint,

brightness, or contrast is required.

Setup Procedure

Warning

For proper installation and mounting it is strongly recom-

mended to use a trained, authorized NEC dealer.

Failure to follow correct mounting procedures could re-

sult in damage to the unit or injury to the installer.

Product warranty does not cover damage caused by im-

proper installation.

Notice:

This monitor requires the use of a tabletop stand or wall

mount unit for permanent installation and use.

This monitor cannot be used without one of these accesso-

ries.

Note:

RETRACTABLE FEET ARE FOR TEMPORARY USE

ONLY AND ARE NOT INTENDED FOR PERMA-

NENT INSTALLATION.

MODEL # PX-42VPU1-ST STAND IS REQUIRED

FOR PERMANENT TABLETOP INSTALLATION.

REPLACE THE FEET WHEN YOU MOVE THE

MONITOR.

Opening the Terminal Board

Cover

Slide the knob and at the same time lift the cover.

Knob

Removing the Terminal Board

Cover

This unit’s terminal board cover can be removed.

First, open the cover and then:

1. Pull the top hook in the direction of the arrow.

2. Pull the entire terminal board cover downward.

To attach the terminal board cover, insert the bottom hook

into the hole, then pull the top hook and insert it into the

hole.

Hook

Attaching the Remote Control

Holder

Insert the top hook of the remote control holder into the

installation hole of the main unit and then insert the bot-

tom hook into its respective hole.

To remove the remote control holder, first release the bot-

tom hook, then release the top hook.

Housing the Remote Control in

the Remote Control Holder

First insert the bottom part of the remote control and con-

tinue to push it in until the top part clicks into place.

To remove, lift the remote control up from the top part and

remove it from the holder.

Part Names and Functions

Front View

1 POWER/STANDBY

The lamp color indicates the mode of power on/standby

or power management.

2 Remote control sensor

Receives the signal from the remote control (when using

the wireless remote control).

3 VIDEO button

Switches to the signal connected with the VIDEO input

connector.

Functions as the (-) button in the on-screen display

(OSM) mode.

4 RGB button

Switches to the signal connected with the RGB input

connector. (Toggle switches between RGB1/RGB2/

RGB3.)

Functions as the (+) button in the on-screen display

(OSM) mode.

5 UP button

Functions as the (▲) button in the on-screen display

(OSM) mode.

6 DOWN button

Functions as the (▼) button in the on-screen display

(OSM) mode.

7 PROCEED button

Sets the on-screen display (OSM) mode and displays

the on-screen menu.

8 EXIT button

Exits the on-screen display (OSM) mode.

9 POWER button

Switches the main power on/off.

495678

Side View.... Terminal Board L/R



AC-IN

OUT

RGB1

HIGH 75Ω

RGB2

VIDEOG B H/CS

R S-VIDEO

10 DIP SW

Sets the various modes of this unit.

11 RGB3 (DVI 29pin)

IN connector: Inputs a digital RGB signal. (TMDS)

Note:

This connector does not support analog input.

12 REMOTE (Mini jack)

IN jack: This jack connects the wired remote control.

THROUGH OUT jack: Outputs as is the remote

control signal that is connected to the REMOTE IN

jack.

* This is used when operating multiple monitors (i.e., of

this unit) with a single remote control.

13 EXTERNAL CONTROL (mini D-Sub 15 pin)

Controlled by the computer’s RS-232C interface.

IN connector: Used when operating this unit with

EXTERNAL CONTROL from a personal computer.

THROUGH OUT connector: Outputs as is the signal

that is input to the EXTERNAL CONTROL IN

connector.

14 CONTROL LOCK

When “CONTROL LOCK” is set to “ON”, the buttons

on the set’s control panel do not function.

15 VIDEO

IN [BNC] connector (BNC): Inputs the video

(composite video signal).

IN [S] connector (DIN 4 pin): Inputs the S video (Y/

C separate signal).

* When connections are made to both the BNC connector

and the S video connector, the signal of the S video

connector has priority.

THROUGH OUT [BNC] connector (BNC): Outputs

as is the signal that is input to the VIDEO IN [BNC]

connector.

THROUGH OUT [S] connector (DIN 4 pin): Outputs

as is the signal that is input to the VIDEO IN [S]

connector.

16 RGB2 [R, G, B, H/CS, V] (BNC)

IN connector: Inputs the analog RGB signal.

The H/V composite signal is connected to the H/CS

connector.

THROUGH OUT connector: Outputs as is the signal

input to the RGB2 IN connector.

75Ω/HIGH switch: This switch selects the impedance

of the connector. It is usually used in the “75Ω” position.

17 RGB1 (mini D-Sub 15 pin)

IN connector: Inputs the analog RGB signal of a

personal computer, etc.

18 AC IN connector

Connects with the supplied power cable.

Insert the prongs completely.

* for PLUGGABLE EQUIPMENT, tee

socket-outlet shall be installed near the

equipment and shall be easily accessible.

POWER

OFF

RGB 1

RGB 2

POSITION / CONTROL

RGB 3

EXIT

PROCEED

VIDEO

CONTRAST

RGB/VIDEO

BRIGHT

COLOR

VIDEO

TINT

SHARPNESS

VISUAL

NORMAL

RASTER

NORMAL

ID SELECT CLEAR

1 POWER ON/OFF button:

Switches the power on/off.

(This does not operate when POWER/STANDBY lamp

of the main unit is off.)

2 Input selection buttons:

Select the input signal that will be displayed on the

screen.

VIDEO: Switches to the signal that is connected to the

VIDEO IN connector.

RGB1: Switches to the signal that is connected to the

RGB1 IN (mini D-sub 15-pin) connector.

RGB2: Switches to the signal that is connected to the

RGB2 IN (BNC type: R, G, B, H/CS, V) connector.

RGB3: Switches to the signal that is connected to the

RGB3 IN connector.

RASTER CONTROL (Screen Adjustment)

3 POSITION/CONTROL buttons (▲▼

Used for screen position adjustment and on-screen

manager (OSM) mode adjustment settings.

4 POSITION/CONTROL buttons (

Enable item selection and adjustments/settings.

ON SCREEN (Screen and Image Adjustment via Menu

Control)

5 PROCEED button:

Displays the main menu of screen and image

adjustments.

Press this button during the display of the main menu

to go to the sub menu.

6 EXIT button:

Exits the on-screen adjustments.

Press this button during the display of the sub menu to

return to the main menu.

VISUAL CONTROL (Image Adjustment)

7 CONTRAST button:

Adjusts the contrast of the RGB signal and the video

signal.

8 BRIGHT button:

Adjusts the brightness of the RGB signal and the video

signal.

9 COLOR button:

Adjusts the density of the video signal colors.

10 TINT button:

Adjusts the tint of the video signal.

(Does not function in the PAL or SECAM settings.)

16 17

Remote Controller

1. Press and open the cover.

2. Align the batteries according to the (+) and (-)

indications inside the case.

3. Replace the cover.

Battery Installation and Replacement

The remote control is powered by two 1.5V AAA batteries.

11 SHARPNESS:

Adjusts the fine screen quality of the video screen.

12 VISUAL NORMAL button:

Returns the screen adjustments to the default factory

visual settings.

13 RASTER NORMAL button:

Returns the screen adjustments to the default factory

raster settings.

14 ID SELECT:

Selects the ID number used when operating one unit at

a time with the remote control when settings of the set

ID have been made to the VIDEO WALL and main

unit.

15 CLEAR:

Deletes the ID number that was set with ID SELECT.

16 Remote control transmitter:

Transmits the remote control signal. (Used with the

wireless remote control.)

17 Remote jack:

Connects the supplied remote control cable when used

as a wired remote control.



Using the wired remote control mode

Connect the included remote control cable to the remote

control's remote jack and "REMOTE IN" jack on the

monitor.

When the cable is connected, the mode automatically

switches to wired remote control.

When the wired remote control mode is used, the remote

control unit can be operated even if no batteries are loaded.

Operating Range

* Use the remote controller within a distance of about 7 m

/ 23ft. from the front of the monitor's remote control sen-

sor and at a horizontal angle of within 30°.

* The remote control operation may not function if the

monitor's remote control sensor is exposed to direct sun-

light or strong artificial light, or if there is an obstacle

between the sensor and the remote control unit.

Note:

Do not connect the wired remote control to the REMOTE

THROUGH OUT jack. If doing so, the remote control

does not work.

Remote Control Cable

To Remote Jack

POWER

OFF

RGB 1

RGB 2

POSITION / CONTR OL

RGB 3

EXIT

PROCEED

VIDEO

CONTRAST

RGB/VIDEO

BRIGHT

COLOR

VIDEO

TINT

SHARPNESS

VISUAL

NORMAL

RASTER

NORMAL

ID SELECT CLEAR

Approx.

7m/23ft

30˚ 30˚

POWER

OFF

RGB 1

RGB 2

POSITION / CONTR OL

RGB 3

EXIT

PROCEED

VIDEO

CONTRAST

RGB/VIDEO

BRIGHT

COLOR

VIDEO

TINT

SHARPNESS

VISUAL

NORMAL

RASTER

NORMAL

ID SELECT CLEAR

Setting details

On-off switching of on-screen display (OSM)

On-off switching of wireless remote control

Setting when shipped

Switch position

OFF

Sync control mode

Automatic selection

PIn No.

Automatic

Manual 1 (Composite)

Manual 2 (Sync-on-green)

No.4

OFF

Sync control setting

No.3

OFF

Switch position

Making the DIP Switch Settings

Before connections are made, the DIP switch should be set to suit the application and

the system structure.

* DIP switches are moved up or down with something fine and pointed such as a

miniature screwdriver or the tip of a ballpoint pen.

Note:

Be sure to switch off the main power before making settings.

1 2 3 4

DIP Switch Functions and Settings

Factory Default Settings

No. 1: On/off switching of on-screen display (OSM)

* Set to “ON” when performing adjustments and viewing displays with the on-screen

display.

Set to “OFF” when displays are not desired.

No. 2: On/off switching of wireless remote control

* When using multiple units under wireless remote control operation, the remote

control signal also enters other monitors and may control them at the same time.

Monitors for which the reception of the wireless remote control signal is not desired

should be set to “OFF.”

* Be sure to switch the units on when the wireless remote control is to be used.

Note:

that use of the wired remote control is not related to this setting.

Pin Nos. 3 and 4 Sync Control Settings

* These are settings of the input sync signals.

* When this unit is set to automatic, it automatically detects the separate sync,

composite sync, and green sync (sync-on-green).

Separate sync should be recognized automatically.

Note:

When both pins No. 1 and No. 2 are set “ON” the synchronization may be

disturbed. Do not set both these pins “ON.”

Power Management Function

The power management function is an energy saving function that automatically reduces the power consumption of the

display when the keyboard or the mouse have not been used for a fixed period. The power management function of the

display becomes operational when the monitor is used with a personal computer based on the VESA DPMS and DVI

DMPM system.

When preparing to display a personal computer screen, check that the personal computer is properly connected to this unit

and that the personal computer power is on.

When the personal computer power is off, the power management function will be activated and this unit will be set to the

off mode.

For information about the power management setting method, see the operating system (OS) manual of the personal

computer you are using. To see the video when the power management function is operating, setting the input selection to

video will switch the function off.

Power Management Modes

There are three modes in the power management function.

* Standby mode

The standby mode is set when the horizontal sync signal from the personal computer is not input.

The image will be displayed immediately upon the input of the horizontal sync signal.

* Suspend mode

The suspend mode is set when the vertical sync signal from the personal computer is not input.

The image will be displayed about 4 seconds after the input of the vertical sync signal.

* Off mode

This unit is set to the off mode when the horizontal/vertical sync signals from the personal computer are not input.

The image will be displayed about 4 seconds after the input of the horizontal/vertical sync signal.

This is the only power management mode during RGB3 input. When there is no TMDS link, the off mode is set. (This

power state is equivalent to the DPMS “off” state.) Displayed approximately 4 seconds after the TMDS link is restored.

The color in which the STANDBY/POWER lamp lights indicates the mode (listed below) in which the unit is set.

Mode

Power ON

Standby

Suspend

OFF

* Standby suspend, off in the table is the condition that exists when power management is ON.

This is not the standby condition set by the remote control.

STANDBY/POWER lamp display

Green

Yellow

Orange

Not lit

Notes

----

Immediate return to normal display

15 W or less, returns to normal display in about 4 seconds

Maximum 8 W or less, returns to normal display in about 4 seconds

Remote control in standby mode

Power cord not connected

Power OFF

Installation

Wiring Diagram

AC-IN

OUT

RGB1

HIGH 75Ω

RGB2

VIDEOG B H/CS

R S-VIDEO

EXTERNAL

CONTROL



PlasmaSync 42/50PD1

IBM XGA/SuperVGA/VGA or

Compatibles or Macintosh G3 series

Macintosh or

Compatibles

Document camera VCR, Video copy

stand or Multimedia application

RGBcable (Supplied)

To mini D-SUB 15 Pin input

To R,G,B,H/CS, V inputs 

(BNC)

To VIDEO IN inputs

Pin adapter for Macintosh

(not supplied)

RGBcable (Supplied)

To mini D-SUB 15 Pin input

To EXTERNAL CONTROL

(mini D-SUB 15 Pin input)

To RGB3 DVI 29pin

(not supplied)

Personal computer 

with a digital 

RGB (TMDS) output

HIROYUK AIZASUSUSUSUSSWA

HIROYUK AIZ

Scan Converter

Connecting Your PC or Macintosh

Computer

Connecting your PC or Macintosh computer to your

PlasmaSync 42/50PD1 will enable you to display your

computer's screen image. All of these following display

standards are supported:

To connect to a PC, Macintosh or computer equipped with

an XGA/SuperVGA/VGA adapter or compatible graphics

adapter, simply:

1. Turn off the power to your monitor and computer.

2. If your PC does not support XGA/SuperVGA/VGA

you will need to install an XGA/SuperVGA/VGA

graphics board. Consult your computer's owner's

manual for your XGA/SuperVGA/VGA configuration.

If you need to install a new board, see the manual that

comes with your new graphics board for installation in-

structions.

3. Use the signal cable that’s supplied to connect your PC

or Macintosh computer to the RGB1 input terminal.

4. Turn on the monitor and the computer.

Note:

Refer to your computer's owner's manual for

more information about your computer's video output

requirements and any special identification or

configuring your monitor's image and monitor may

require.

Connecting Your VCR DVD or

Laser Disc Player

Use a composite video cable with BNC connector and

RCA video cables (not provided) to connect your VCR,

DVD or laser disc player to your PlasmaSync 42/50PD1.

To make these connections, simply:

1. Turn off the power to your monitor and VCR, DVD or

laser disc player.

2. Connect one end of your video cable to the video out-

put connector on the back of your VCR, DVD or laser

disc player, connect the other and to the VIDEO input

terminal (BNC type) of the monitor.

NOTE: You will need a BNC to RCA adapter (not in-

cluded) to connect a video cable with an RCA pin jack to

the BNC input terminal of the PlasmaSync 42/50PD1.

3. Turn on the monitor and the VCR, DVD or laser disc

player.

Note:

Refer to your VCR or laser disc player owner's

manual for more information about your equipment's

video output requirements.

Note:

S-VIDEO IN terminals will take preference

over VIDEO IN terminals when a component is

connected to each terminal and S-VIDEO selected.

Connecting Your Document

Camera

You can connect your PlasmaSync 42/50PD1 to a document

camera. To do so, simply:

1.Turn off the power to your monitor and document

camera.

2.Use a standard video cable to connect your document

camera to the VIDEO input terminal(BNC-type) of the

monitor.

3.Turn on the monitor and the document camera.

Note:

Refer to your document camera's owner's

manual for more information about your camera's

video output requirements .

Connections with Equipment that

has a Digital Interface

Connections can be made with equipment that is equipped

with a digital interface compliant with the DVI (Digital

Visual Interface) standard.

* Use a DVI 29-pin signal cable (available separately)

and the ferrite cores (supplied) when making connec-

tions to the RGB3 IN (DVI) connector of the main unit.

Notes:

1. Input TMDS signals conforming to DVI standards.

The TMDS input corresponds to 1 link.

2. To maintain display quality, use a cable with a qual-

ity prescribed by DVI standards that is within 5

meters in length.

La page est en cours de chargement...

NEC PlasmaSync® 50VP1 Le manuel du propriétaire

Marque: NEC

Modèle: PlasmaSync® 50VP1

Catégorie: Téléviseurs à écran plasma

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: NEC PlasmaSync® 50VP1 Owner's manual

NEC PlasmaSync® 50VP1 Le manuel du propriétaire

NEC PlasmaSync® 50VP1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents